SP4704-26-Q-0038 Computerized Mat Cutter.pdf

For the best experience, open this PDF portfolio in

Acrobat X or Adobe Reader X, or later.

Get Adobe Reader Now!

http://www.adobe.com/go/reader

SOURCE SELECTION INFO - SEE FAR 2.101 & 3.104 PAGE 1 of 3

Computerized Mat Cutter (CMC) System for DLA HQ at Fort Belvoir, VA (DM-FFX) DLA HQ at Fort Belvoir, VA (DM-FFX) requires Wizard Z1 Computerized Mat Cutter (CMC). This system is required to automate framing, cutting, embossing, and drawing operations with computerized control, ensuring high repeatability, reduced waste, and enhanced operational throughput. The Contractor shall deliver, install, and license a complete Wizard Z1 Computerized Mat Cutter system.

The scope of work encompasses:

Delivery of the Wizard Z1 hardware, integrated PC controller, and proprietary software.

Supply of a comprehensive suite of standard and specialized cutting, debossing, and drawing accessories. Provision of operating software licenses (FrameShop™ Design & Cut Software).

Delivery of ongoing technical support, software updates, and hardware warranties.

Performance of on-site installation, system calibration, and operator training.

Requirement Overview

• One (1) each – Wizard Z1 CMC Standard Package o Includes:

Z1 CNC Unit with SmartClamps™ Board & SwitchBlade™ Cartridge

System Base mount (Floor Stand) Integrated Windows® Computer & FrameShop™ License Cartridge set: 45° Standard, 45°+ Deep, 52° Intricate, 90° Straight Debossing Kit (3 Tip Sizes) and Pen Kit 1-Year PC Warranty & 2-Year CMC Warranty (Essential Premium Service

Plan)

• One (1) each – Vinyl Kit

• One (1) each – Box Kit

• One (1) each – Computer Stand

• One (1) each – California Air Tools® Quiet Compressor

• On-Site Installation, System Calibration, and Operator Training

Shipping Address:

DLA HQ – DM-FFX

ATTN: Curtis Cox Multimedia Room 2550 8795 John J. Kingman Road Fort Belvoir, VA 22060-6221

Delivery Lead Time: 30 Days ARO

SOURCE SELECTION INFO - SEE FAR 2.101 & 3.104 PAGE 2 of 3

1.0 REQUIREMENT SPECIFICATIONS

The Computerized Mat Cutter must meet or exceed the following technical and operational criteria, which are uniquely satisfied by the Wizard Z1 CMC:

1.1 Physical & Performance Specifications

Maximum Material Size (H x W): Must accommodate board sizes up to 40" x 60" (101.6cm × 152.4cm).

Cutting Performance Speed: Must achieve cutting speeds of up to 20 inches per second (50.8 cm/sec) to maintain high production efficiency.

Physical Footprint (W x D): Must fit within an operating space of 74" x 46" (188.0cm × 116.8cm).

Origin of Manufacture: Designed, manufactured, and assembled in the USA.

1.2 Advanced Automation & Precision Features

Zero-Waste Edge-to-Edge Cutting: Equipment must support edge-to-edge cutting capability to maximize material utilization and minimize scrap waste.

Digital Depth Control: System must feature automated, software-controlled blade depth adjustment to eliminate manual dial-turning errors when changing materials.

Auto-Homing: The cutting head must automatically align to its home position via computerized control to secure repeatable starting points.

Intelligent Clamping with Collision Detection: Clamping systems must feature real-time sensor technology (equivalent to SmartClamps™) and LED indicator lights to notify operators of required physical adjustments. The unit must feature an active Collision Detection and Avoidance System to prevent tool and board damage during cutting paths.

Modular Cartridge System: Must feature a quick-change cartridge system (equivalent to SwitchBlade™) to allow rapid, tool-free transitions between bevel angles, straight cuts, drawing tools, and debossing heads.

1.3 Multi-Functional Tooling Capability

The system must act as a multi-functional production station capable of the following operations:

Bevel & Straight Cutting: 45-degree standard, 45-degree deep bevel (for thick boards), 52-degree intricate bevel, and 90-degree straight cuts.

Computerized Drawing (Pen Tool): Automated pen drawing on matte boards for decorative detailing and custom calligraphy.

Embossing/Debossing: Computerized debossing utilizing multiple tip sizes (minimum of 3 sizes) to compress matte board fibers without cutting.

Expansion Capabilities: System must support options for vinyl cutting and corrugated cardboard box making.

1.4 Control Software Requirements

Powered by user-friendly, industry-standard software (FrameShop™ or equivalent) capable of:

Nested layouts (nesting) to maximize board usage. Tiling for oversized mat layouts. Optimized

SOURCE SELECTION INFO - SEE FAR 2.101 & 3.104 PAGE 3 of 3 toolpaths for exterior cuts. Step-by-step visual guidance for machine operators to ensure consistency across shift work.

2.0 WARRANTIES, SERVICE LEVEL AGREEMENTS (SLA), & SOFTWARE LICENSING

2.1 Warranty Coverage

The contractor shall provide a dual-tiered warranty package included in the base system price:

Computer Controller Warranty: 1-Year hardware warranty provided directly by the original PC manufacturer.

Matte Cutter Warranty: 2-Year CMC Warranty under the Essential Premium Service Plan. This plan must provide:

Complete hardware coverage for all mechanical and electronic components.

Direct technical support via phone and online channels from Wizard International, Inc.

Full access to Wizard University (comprehensive video training modules, operational guides, and continuing education for machine operators).

2.2 Proprietary Software Licensing (FrameShop™)

Grant of License: Licensing for the FrameShop™ Design & Cut Software is granted directly with the purchase of the Z1 CMC system.

Scope of Use: The license authorizes design, nesting, tiling, and cutting actions for the purchased hardware unit.

Updates: License terms must include access to software updates and optimization patches issued by Wizard International, Inc. during the warranty period.

2.3 Technical Support Infrastructure

All warranty claims, replacement parts, software troubleshooting, and technical assistance must be handled directly by Wizard International, Inc.’s corporate support team in Mukilteo, WA. Third-party support or unauthorized repairs are prohibited to maintain warranty validity.

SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL ITEMS

OFFEROR TO COMPLETE BLOCKS 12, 17, 23, 24, & 30 7018129953

1. REQUISITION NUMBER

2. CONTRACT NO. 3. AWARD/EFFECTIVE

DATE

4. ORDER NUMBER

SP4704-26-Q-0038

5. SOLICITATION NUMBER

2026 SEP 04

6. SOLICITATION ISSUE

DATE

Cherlyn Carby DCC0179

a. NAME

Phone: 8047739813

b. TELEPHONE NUMBER (No Collect calls)

2026 SEP 10

8. OFFER DUE DATE/

LOCAL TIME

9. ISSUED BY CODE SP4704

DCSO RICHMOND DIVISION #2

6090 STRATHMORE RD.

RICHMOND VA 23297-5441

RICHMOND VA 23237

USA

10. THIS ACQUISITION IS UNRESTRICTED OR SET ASIDE: % FOR:

SMALL BUSINESS

HUBZONE SMALL

BUSINESS

WOMEN-OWNED SMALL BUSINESS

(WOSB) ELIGIBLE UNDER THE WOMEN-OWNED

SMALL BUSINESS PROGRAM

8 (A)

SERVICE-DISABLED

VETERAN-OWNED

SMALL BUSINESS

322211NAICS:

SIZE STANDARD:

11. DELIVERYFOR FOB DESTINA-

TION UNLESS BLOCK IS

MARKED

12. DISCOUNT TERMS

13a. THIS CONTRACT IS A

RATED ORDER UNDER

DPAS (15 CFR 700)

13b. RATING

14. METHOD OF SOLICITATION

RFQ IFB RFP

15. DELIVER TO CODE 16. ADMINISTERED BY CODE

17a. CONTRACTOR/ CODE

OFFEROR

FACILITY

CODE

TELEPHONE NO.

18a. PAYMENT WILL BE MADE BY CODE

17b. CHECK IF REMITTANCE IS DIFFERENT AND PUT SUCH ADDRESS IN

OFFER

18b. SUBMIT INVOICES TO ADDRESS SHOWN IN BLOCK 18a UNLESS BLOCK

BELOW IS CHECKED

19.

ITEM NO.

20.

SCHEDULE OF SUPPLIES/SERVICES

21.

QUANTITY

22.

UNIT

23.

UNIT PRICE

24.

AMOUNT

See Schedule

(Use Reverse and/or Attach Additional Sheets as Necessary)

25. ACCOUNTING AND APPROPRIATION DATA 26. TOTAL AWARD AMOUNT (For Govt. Use Only)

27a. SOLICITATION INCORPORATES BY REFERENCE FAR 52.212-1, 52.212-4. FAR 52.212-3 AND 52.212-5 ARE ATTACHED. ADDENDA ARE ARE NOT ATTACHED

27b. CONTRACT/PURCHASE ORDER INCORPORATES BY REFERENCE FAR 52.212-4. FAR 52.212-5 IS ATTACHED. ADDENDA ARE ARE NOT ATTACHED

28. CONTRACTOR IS REQUIRED TO SIGN THIS DOCUMENT AND RETURN

COPIES TO ISSUING OFFICE. CONTRACTOR AGREES TO FURNISH AND

DELIVER ALL ITEMS SET FORTH OR OTHERWISE IDENTIFIED ABOVE AND ON ANY

ADDITIONAL SHEETS SUBJECT TO THE TERMS AND CONDITIONS SPECIFIED

29. AWARD OF CONTRACT: REF. OFFER

DATED . YOUR OFFER ON SOLICITATION

(BLOCK 5), INCLUDING ANY ADDITIONS OR CHANGES WHICH ARE

SET FORTH HEREIN, IS ACCEPTED AS TO ITEMS:

30a. SIGNATURE OF OFFEROR/CONTRACTOR 31a. UNITED STATES OF AMERICA (SIGNATURE OF CONTRACTING OFFICER)

30b. NAME AND TITLE OF SIGNER (Type or Print) 30c. DATE SIGNED 31b. NAME OF CONTRACTING OFFICER (Type or Print) 31c. DATE SIGNED

SEE SCHEDULE

7. FOR SOLICITATION

INFORMATION CALL:

SEE SCHEDULE

12:00 PM

STANDARD FORM 1449 (REV. 2/2012)

Prescribed by GSA - FAR (48 CFR) 53.212

AUTHORIZED FOR LOCAL REPRODUCTION

PREVIOUS EDITION IS NOT USABLE

SEE ADDENDUM

EDWOSB

32a. QUANTITY IN COLUMN 21 HAS BEEN

ACCEPTED, AND CONFORMS TO THE CONTRACT, EXCEPT AS NOTED:RECEIVED INSPECTED

COMPLETE PARTIAL FINAL

STANDARD FORM 1449 (REV. 2/2012) BACK

36. PAYMENT

PARTIAL FINAL

20.

SCHEDULE OF SUPPLIES/SERVICES

21.

QUANTITY

22.

UNIT

23.

UNIT PRICE

24.

AMOUNT

19.

ITEM NO.

32b. SIGNATURE OF AUTHORIZED GOVERNMENT

REPRESENTATIVE

32c. DATE 32d. PRINTED NAME AND TITLE OF AUTHORIZED GOVERNMENT

REPRESENTATIVE

32f. TELEPHONE NUMBER OF AUTHORIZED GOVERNMENT REPRESENTATIVE

32g. E-MAIL OF AUTHORIZED GOVERNMENT REPRESENTATIVE

33. SHIP NUMBER 34. VOUCHER NUMBER 35. AMOUNT VERIFIED

CORRECT FOR

37. CHECK NUMBER

38. S/R ACCOUNT NO. 39. S/R VOUCHER NUMBER 40. PAID BY

42a. RECEIVED BY (Print)

41b. SIGNATURE AND TITLE OF CERTIFYING OFFICER 41c. DATE

42c. DATE REC'D (YY/MM/DD) 42d. TOTAL CONTAINERS

41a. I CERTIFY THIS ACCOUNT IS CORRECT AND PROPER FOR PAYMENT

32e. MAILING ADDRESS OF AUTHORIZED GOVERNMENT REPRESENTATIVE

42b. RECEIVED AT (Location)

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED:

CONTINUED ON NEXT PAGE

PAGE 3 OF 16 PAGES

COMPUTERIZED MAT CUTTER (CMC)

The Purpose of this requirement is to provide the Wizard Z1 Computerized Mat Cutter (CMC) for Department Logistics Agency (DLA) Head Quarters at Fort Belvoir, VA (DM-FFX). This system is required to automate framing, cutting, embossing, and drawing operations with computerized control, ensuring high repeatability, reduced waste, and enhanced operational throughput. The Contractor shall deliver, install, and license a complete Wizard Z1 Computerized Mat Cutter system. See attached Specifications. Requested delivery is 30 days ARO.

NAICS Code 333515 (Small Business Size 500 employees)

The contract will be Firm-Fixed Price.

INSTRUCTIONS TO QUOTERS

Quotes shall be submitted to Cherlyn Carby at Cherlyn.Carby@dla.mil.

Quotes must be submitted via email to the contract specialist no later than 12:00pm EDT, September 10, 2026. The vendor is responsible for confirming quote receipt. Please note that external emails are often delayed so quotes should not be submitted at the last minute. Late quotes may or may not be considered at the contracting officer’s discretion.

The submission email must include the following:

-Company name, address, UIE, and CAGE (included in body of email);

-Point of contact for questions (included in body of email);

-Provide quoted delivery and pricing for all elements of Schedule B (page 4). All pricing must be limited to two decimal places.

-If pricing is provided as a separate attachment, the attachment cannot exceed three pages total – this is inclusive of the cover page, table of contents, etc.

-Do not include any additional information/attachments that is not specifically requested as it will not be reviewed.

All submissions must be in Microsoft Word, Microsoft Excel, or Adobe PDF unless otherwise specified. Word and PDF documents must adhere to the following: 8.5” x 11”; Times New Roman; 11pt font. Table fonts must be Times New Roman with font no smaller than 9pt.

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED:

PAGE 4 OF 16 PAGES

SECTION B

Delivery Days:____________________________________

CLIN 0001 - Wizard Z1 CMC Standard Package - Quantity 1 EA - Price $__________________________________

CLIN 0002 - Vinyl Kit - Quantity 1 EA - Price $__________________________________

CLIN 0003 - Box Kit - Quantity 1 EA - Price $__________________________________

CLIN 0004 - Computer Stand - Quantity 1 EA - Price $__________________________________

CLIN 0005 - California Air Tools Quiet Compressor - Quantity 1 EA - Price $__________________________________

CLIN 0006 - On-Site Installation, System Calibration, and Operator Training -

Quantity 1 EA - Price $_______________________________

GRAND TOTAL: $__________________________________

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 5 OF 16 PAGES

SECTION C - SPECIFICATIONS/SOW/SOO/ORD

C03 CONTRACTOR RETENTION OF SUPPLY CHAIN TRACEABILITY DOCUMENTATION (JUN 2023)

SECTION E - INSPECTION AND ACCEPTANCE

52.246-2 INSPECTION OF SUPPLIES FIXED PRICE (AUG 1996) FAR

SECTION F - DELIVERIES OR PERFORMANCE

52.242-15 STOP-WORK ORDER (AUG 1989) FAR

52.242-17 GOVERNMENT DELAY OF WORK (APR 1984) FAR

52.247-34 F.O.B. DESTINATION (JAN 1991) FAR

SECTION G - CONTRACT ADMINISTRATION DATA

252.232-7006 WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (PRE-FILLED) (JAN 2023) DFARS As prescribed in 232.7004 (b), use the following clause:

(a) Definitions. As used in this clause - Department of Defense Activity Address Code (DoDAAC) is a six position code that uniquely identifies a unit, activity, or organization.

Document type means the type of payment request or receiving report available for creation in Wide Area WorkFlow (WAWF).

Local processing office (LPO) is the office responsible for payment certification when payment certification is done external to the entitlement system.

Payment request and receiving report are defined in the clause at 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports.

(b) Electronic invoicing. The WAWF system provides the method to electronically process vendor payment requests and receiving reports, as authorized by Defense Federal Acquisition Regulation System (DFARS) 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports.

(c) WAWF access. To access WAWF, the Contractor shall -

(1) Have a designated electronic business point of contact in the System for Award Management at https://www.sam.gov and

(2) Be registered to use WAWF at https://wawf.eb.mil/ following the step-by-step procedures for self-registration available at this Web site.

(d) WAWF training. The Contractor should follow the training instructions of the WAWF Web-Based Training Course and use the Practice Training Site before submitting payment requests through WAWF. Both can be accessed by selecting the “Web Based Training” link on the WAWF home page at https:// wawf.eb.mil/.

(e) WAWF methods of document submission. Document submissions may be via Web entry, Electronic Data Interchange, or File Transfer Protocol.

(f) WAWF payment instructions. The Contractor shall use the following information when submitting payment requests and receiving reports in WAWF for this contract or task or delivery order:

(1) Document type. The Contractor shall submit payment requests using the following document type(s):

(i) For cost-type line items, including labor-hour or time-and-materials, submit a cost voucher.

(ii) For fixed price line items -

(A) That require shipment of a deliverable, submit the invoice and receiving report specified by the Contracting Officer.

(Contracting Officer: Insert applicable invoice and receiving report document type(s) for fixed price line items that require shipment of a deliverable.)

Invoice (stand-alone) and Receiving Report (stand-alone) or Invoice and Receiving Report (combination)

(B) For services that do not require shipment of a deliverable, submit either the Invoice 2in1, which meets the requirements for the invoice and receiving report, or the applicable invoice and receiving report, as specified by the Contracting Officer.

(Contracting Officer: Insert either “Invoice 2in1” or the applicable invoice and receiving report document type(s) for fixed price line items for services.)

(iii) For customary progress payments based on costs incurred, submit a progress payment request.

(iv) For performance based payments, submit a performance based payment request.

(v) For commercial financing, submit a commercial financing request.

(2) Fast Pay requests are only permitted when Federal Acquisition Regulation (FAR) 52.213-1 is included in the contract.

[Note: The Contractor may use a WAWF “combo” document type to create some combinations of invoice and receiving report in one step.]

(3) Document routing. The Contractor shall use the information in the Routing Data Table below only to fill in applicable fields in WAWF when creating payment requests and receiving reports in the system.

Routing Data Table *

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 6 OF 16 PAGES

SECTION G - CONTRACT ADMINISTRATION DATA (CONTINUED)

Field Name in WAWF Data to be entered in WAWF Guidance

Pay Official DoDAAC See Block 12 (SF26), 15 (DD 1155), or 18a

(SF1449)

(If blank, see resulting award)

Issue By DoDAAC See Block 5 (SF26), 6 (DD 1155), or 9 (SF1449)

Admin DoDAAC See Block 6 (SF26), 7 (DD 1155), or 16 (SF1449)

Inspect By DoDAAC SEE SECTION B (If blank, see resulting

Ship To Code SEE SECTION B (If blank, see resulting

Ship From Code SEE SECTION B (If blank, see resulting

Mark For Code SEE SECTION B (If blank, see resulting

Service Approver (DoDAAC)

Service Acceptor (DoDAAC)

Accept at Other DoDAAC (If blank, see resulting

LPO DoDAAC (If blank, see resulting

DCAA Auditor DoDAAC (If blank, see resulting

Other DoDAAC(s) (If blank, see resulting

(* Contracting Officer: Insert applicable DoDAAC information. If multiple ship to/acceptance locations apply, insert “See Schedule” or “Not applicable.”) (** Contracting Officer: If the contract provides for progress payments or performance-based payments, insert the DoDAAC for the contract administration office assigned the functions under FAR 42.302(a)(13).)

(4) Payment request. The Contractor shall ensure a payment request includes documentation appropriate to the type of payment request in accordance with the payment clause, contract financing clause, or Federal Acquisition Regulation 52.216-7, Allowable Cost and Payment, as applicable.

(5) Receiving report. The Contractor shall ensure a receiving report meets the requirements of DFARS Appendix F.

(g) WAWF point of contact. (1) The Contractor may obtain clarification regarding invoicing in WAWF from the following contracting activity's WAWF point of contact.

See administer listed on page 1

(Contracting Officer: Insert applicable information or “Not applicable.”)

(2) Contact the WAWF helpdesk at 866-618-5988, if assistance is needed.

(End of Clause)

SECTION H - SPECIAL CONTRACT REQUIREMENTS

H18 DEFENSE PRIORITIES AND ALLOCATIONS SYSTEM (DPAS) RATED AWARDS (FEB 2025)

SECTION I - CONTRACT CLAUSES

52.202-1 DEFINITIONS (JUN 2020) FAR

52.203-3 GRATUITIES (APR 1984) FAR

52.203-6 RESTRICTIONS ON SUBCONTRACTOR SALES TO THE GOVERNMENT (JUN 2020) FAR

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 7 OF 16 PAGES

SECTION I - CONTRACT CLAUSES (CONTINUED)

52.203-19 PROHIBITION ON REQUIRING CERTAIN INTERNAL CONFIDENTIALITY AGREEMENTS OR STATEMENTS (JAN 2017)

FAR

52.203-18 PROHIBITION ON CONTRACTING WITH ENTITIES THAT REQUIRE CERTAIN INTERNAL CONFIDENTIALITY

AGREEMENTS OR STATEMENTS-REPRESENTATION (JAN 2017) FAR

252.203-7000 REQUIREMENTS RELATING TO COMPENSATION OF FORMER DOD OFFICIALS (SEP 2011) DFARS

252.203-7002 REQUIREMENT TO INFORM EMPLOYEES OF WHISTLEBLOWER RIGHTS (DEC 2022) DFARS

52.204-13 SYSTEM FOR AWARD MANAGEMENT -- MAINTENANCE (DEVIATION 2026-O0038) (FEB 2026) FAR

52.204-19 INCORPORATION BY REFERENCE OF REPRESENTATIONS AND CERTIFICATIONS (DEVIATION 2026-O0038) (FEB

2026) FAR

252.204-7000 DISCLOSURE OF INFORMATION (OCT 2016) DFARS

252.204-7004 ANTITERRORISM AWARENESS TRAINING FOR CONTRACTORS (JAN 2023) DFARS

252.204-7014 LIMITATIONS ON THE USE OR DISCLOSURE OF INFORMATION BY LITIGATION SUPPORT CONTRACTORS (JAN

2023) DFARS

252.204-7015 NOTICE OF AUTHORIZED DISCLOSURE OF INFORMATION FOR LITIGATION SUPPORT (JAN 2023) DFARS

252.240-7997 NIST SP 800-171 DOD ASSESSMENT REQUIREMENTS (DEVIATION 2026-O0025) (FEB 2026) DFARS

52.222-3 CONVICT LABOR (JUN 2003) FAR

52.222-19 CHILD LABOR - COOPERATION WITH AUTHORITIES AND REMEDIES (DEVIATION 2026-O0038) (FEB 2026) FAR

52.222-36 EQUAL OPPORTUNITY FOR WORKERS WITH DISABILITIES (DEVIATION 2026-O0038) (FEB 2026) FAR

52.222-37 EMPLOYMENT REPORTS ON VETERANS (DEVIATION 2026-O0038) (FEB 2026) FAR

52.222-50 COMBATING TRAFFICKING IN PERSONS (NOV 2021) FAR

52.222-90 ADDRESSING DEI DISCRIMINATION BY FEDERAL CONTRACTORS (DEVIATION 2026-O0040, REVISION 1) (APR 2026)

FAR

52.223-3 HAZARDOUS MATERIAL IDENTIFICATION AND SAFETY DATA (DEVIATION 2026-O0038) (FEB 2026) FAR As prescribed in 23.304(a)(1), insert the following clause:

(a) Hazardous material, as used in this clause, includes any material defined as hazardous under the latest version of Federal Standard No. 313 (including revisions adopted during the term of the contract).

(b) The Offeror must list any hazardous material, as defined in paragraph (a) of this clause, to be delivered under this contract. The hazardous material shall be properly identified and include any applicable identification number, such as National Stock Number or Special Item Number. This information shall also be included on the Safety Data Sheet submitted under this contract.

Material (If none, insert None)

Identification No.

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 8 OF 16 PAGES

(c) This list must be updated during performance of the contract whenever the Contractor determines that any other material to be delivered under this contract is hazardous.

(d) The apparently successful offeror agrees to submit, for each item as required prior to award, a Safety Data Sheet, meeting the requirements of 29 CFR 1910.1200(g) and the latest version of Federal Standard No. 313, for all hazardous material identified in paragraph (b) of this clause. Data shall be submitted in accordance with Federal Standard No. 313, whether or not the apparently successful offeror is the actual manufacturer of these items. Failure to submit the Safety Data Sheet prior to award may result in the apparently successful offeror being considered nonresponsible and ineligible for award.

(e) If, after award, there is a change in the composition of the item(s) or a revision to Federal Standard No. 313, which renders incomplete or inaccurate the data submitted under paragraph (d) of this clause, the Contractor shall promptly notify the Contracting Officer and resubmit the data.

(f) Neither the requirements of this clause nor any act or failure to act by the Government shall relieve the Contractor of any responsibility or liability for the safety of Government, Contractor, or subcontractor personnel or property.

(g) Nothing contained in this clause shall relieve the Contractor from complying with applicable Federal, State, and local laws, codes, ordinances, and regulations (including the obtaining of licenses and permits) in connection with hazardous material.

(h) The Government's rights in data furnished under this contract with respect to hazardous material are as follows:

(1) To use, duplicate and disclose any data to which this clause is applicable. The purposes of this right are to --

(i) Apprise personnel of the hazards to which they may be exposed in using, handling, packaging, transporting, or disposing of hazardous materials;

(ii) Obtain medical treatment for those affected by the material; and

(iii) Have others use, duplicate, and disclose the data for the Government for these purposes.

(2) To use, duplicate, and disclose data furnished under this clause, in accordance with subparagraph (h)(1) of this clause, in precedence over any other clause of this contract providing for rights in data.

(3) The Government is not precluded from using similar or identical data acquired from other sources.

(End of Clause)

52.223-23 SUSTAINABLE PRODUCTS (DEVIATION 2026-O0038) (FEB 2026) FAR

252.225-7001 BUY AMERICAN AND BALANCE OF PAYMENTS PROGRAM (FEB 2024) DFARS

252.225-7001 BUY AMERICAN AND BALANCE OF PAYMENTS PROGRAM, ALT II (FEB 2024) DFARS

252.225-7002 QUALIFYING COUNTRY SOURCES AS SUBCONTRACTORS (MAR 2022) DFARS

252.225-7013 DUTY-FREE ENTRY (OCT 2025) DFARS

252.225-7048 EXPORT-CONTROLLED ITEMS (JUN 2013) DFARS

252.225-7052 RESTRICTION ON THE ACQUISITION OF CERTAIN MAGNETS, TANTALUM, AND TUNGSTEN (MAY 2024) DFARS

52.226-8 ENCOURAGING CONTRACTOR POLICIES TO BAN TEXT MESSAGING WHILE DRIVING (MAY 2024) FAR

52.232-40 PROVIDING ACCELERATED PAYMENTS TO SMALL BUSINESS SUBCONTRACTORS (MAR 2023) FAR

252.232-7010 LEVIES ON CONTRACT PAYMENTS (DEC 2006) DFARS

52.233-3 PROTEST AFTER AWARD (AUG 1996) FAR

52.243-1 CHANGES - FIXED PRICE (AUG 1987) FAR

5452.233-9001 DISPUTES - AGREEMENT TO USE ALTERNATIVE DISPUTE RESOLUTION (JUN 2020) DLAD

(a) The parties agree to negotiate with each other to try to resolve any disputes that may arise. If unassisted negotiations are unsuccessful, the parties will use alternative dispute resolution (ADR) techniques to try to resolve the dispute. Litigation will only be considered as a last resort when ADR is unsuccessful or has been documented by the party rejecting ADR to be inappropriate for resolving the dispute.

(b) Before either party determines ADR inappropriate, that party must discuss the use of ADR with the other party. The documentation rejecting ADR must be signed by an official authorized to bind the Contractor (see Federal Acquisition Regulation (FAR) clause 52.233-1), or, for the Agency, by the Contracting Officer, and approved at a level above the Contracting Officer after consultation with the ADR Specialist and with legal. Contractor personnel are also encouraged to include the ADR Specialist in their discussions with the Contracting Officer before determining ADR to be inappropriate.

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 9 OF 16 PAGES

(c) The offeror should check here to opt out of this clause:

[ ] Alternate wording may be negotiated with the contracting officer.

52.240-91 SECURITY PROHIBITIONS AND EXCLUSIONS (DEVIATION 2026-O0038) (FEB 2026) FAR

52.240-91 SECURITY PROHIBITIONS AND EXCLUSIONS, ALT I (DEVIATION 2026-O0038) (FEB 2026) FAR Alternate I As prescribed in 40.205(b), substitute the following paragraph (e)(1) for paragraph (e)(1) of the basic clause:

(e) Governmentwide exclusion and removal orders.

(1) Contractors are prohibited from providing or using as part of the performance of the contract any covered article, or any products or services produced or provided by a source, if the covered article or the source is prohibited by any applicable FASCSA orders identified by the checkbox(es) in this paragraph (e)

(1). [Contracting Officer must select either “yes” or “no” for each of the following types of FASCSA orders:]

Yes [] No [] DHS FASCSA Order

Yes [] No [] DoD FASCSA Order

Yes [] No [] DNI FASCSA Order

252.204-7003 CONTROL OF GOVERNMENT PERSONNEL WORK PRODUCT (APR 1992) DFARS

252.204-7009 LIMITATIONS ON THE USE OR DISCLOSURE OF THIRD-PARTY CONTRACTOR REPORTED CYBER INCIDENT

INFORMATION (JAN 2023) DFARS

252.204-7012 SAFEGUARDING COVERED DEFENSE INFORMATION AND CYBER INCIDENT REPORTING (MAY 2024) DFARS

252.204-7018 PROHIBITION ON THE ACQUISITION OF COVERED DEFENSE TELECOMMUNICATIONS EQUIPMENT OR SERVICES

(JAN 2023) DFARS

252.225-7051 PROHIBITION ON ACQUISITION OF CERTAIN FOREIGN COMMERCIAL SATELLITE SERVICES (DEC 2022) DFARS

Standard Element ZB_240_7998 has no Title

Standard Element ZB_240_7999 has no Title

252.243-7001 PRICING OF CONTRACT MODIFICATIONS (DEC 1991) DFARS

252.244-7000 SUBCONTRACTS FOR COMMERCIAL PRODUCTS OR COMMERCIAL SERVICES (NOV 2023) DFARS

252.244-7999 SUBCONTRACTS FOR COMMERCIAL PRODUCTS OR COMMERCIAL SERVICES (DEVIATION 2026-O0015) (FEB

2026) DFARS

252.246-7007 CONTRACTOR COUNTERFEIT ELECTRONIC PART DETECTION AND AVOIDANCE SYSTEM (JAN 2023) DFARS

252.246-7008 SOURCES OF ELECTRONIC PARTS (JAN 2023) DFARS

252.247-7023 TRANSPORATION OF SUPPLIES BY SEA --- BASIC (OCT 2024) DFARS

Basic. As prescribed in 247.574(b) and (b)(1), use the following clause:

(a) Definitions. As used in this clause -- “Foreign-flag vessel” means any vessel that is not a U.S.-flag vessel.

“Ocean transportation” means any water-borne transportation aboard a ship, vessel, boat, barge, ferry, or the like outside the internal waters of the United

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 10 OF 16 PAGES

States as defined in 33 CFR 2.24.

“Subcontractor” means a supplier, materialman, distributor, or vendor at any level below the prime contractor whose contractual obligation to perform results from, or is conditioned upon, award of the prime contract and who is performing any part of the work or other requirement of the prime contract.

“Supplies” means supplies that are clearly identifiable for eventual use by or owned by DoD at the time of transportation by sea, or are otherwise transported by DoD, regardless of ownership or use by DoD. An item is clearly identifiable for eventual use by DoD if, for example, the contract documentation contains a reference to a DoD contract number or a military destination.

“U.S.-flag vessel” means either a vessel belonging to the United States or a vessel of the United States as that term is defined in 46 U.S.C. 116..

(b)(1) The Contractor shall use U.S.-flag vessels when transporting any supplies by sea under this contract.

(2) A subcontractor transporting supplies by sea under this contract shall use U.S.-flag vessels if --

(i) This contract is a construction contract; or

(ii) The supplies being transported are --

(A) Other than commercial products; or

(B) Commercial products that --

(1) The Contractor is reselling or distributing to the Government without adding value (generally, the Contractor does not add value to items that it subcontracts for f.o.b. destination shipment);

(2) Are shipped in direct support of U.S. military contingency operations, exercises, or forces deployed in humanitarian or peacekeeping operations; or

(3) Are commissary or exchange cargoes transported outside of the Defense Transportation System in accordance with 10 U.S.C. 2643.

(c) The Contractor and its subcontractors may request, via the Contracting Officer, a waiver of the requirement to use a U.S.-flag vessel, or identification of any available U.S.-flag vessels, if the Contractor or a subcontractor sufficiently explains that --

(1) U.S.-flag vessels are not available at a fair and reasonable rate for commercial vessels of the United States; or

(2) U.S.-flag vessels are otherwise not available.

(d) The Contractor must submit any request for use of foreign-flag vessels in writing to the Contracting Officer at least 45 days prior to the sailing date necessary to meet its delivery schedules. The Contracting Officer will process requests submitted after such date(s) as expeditiously as possible, however, if a DoD waiver is not approved prior to shipper's sailing date, this will not of itself constitute a compensable delay under this or any other clause of this contract. Requests shall contain at a minimum --

(1) Type, weight, and cube of cargo;

(2) Required shipping date;

(3) Special handling and discharge requirements;

(4) Loading and discharge points;

(5) Name of shipper and consignee;

(6) Prime contract number; and

(7) A documented description of current, diligent efforts made to secure U.S.-flag vessels, including points of contact (with names and telephone numbers) with at least two U.S.-flag carriers contacted. Copies of quotes will suffice for this purpose. Copies of telephone notes, emails, and other relevant communications will otherwise be considered for this purpose.

(e) The Contractor shall, within 30 days after each shipment covered by this clause, provide the Contracting Officer and the Maritime Administration, Office of Cargo Preference, U.S. Department of Transportation, 400 Seventh Street SW, Washington, DC 20590, one copy of the rated on board vessel operating carrier's ocean bill of lading, which shall contain the following information:

(1) Prime contract number;

(2) Name of vessel;

(3) Vessel flag of registry;

(4) Date of loading;

(5) Port of loading;

(6) Port of final discharge;

(7) Description of commodity;

(8) Gross weight in pounds and cubic feet if available;

(9) Total ocean freight in U.S. dollars; and

(10) Name of the carrier.

(f) If this contract exceeds the simplified acquisition threshold, the Contractor shall provide with its final invoice under this contract a representation that to the best of its knowledge and belief --

(1) No ocean transportation was used in the performance of this contract;

(2) Ocean transportation was used and only U.S.-flag vessels were used for all ocean shipments under the contract;

(3) Ocean transportation was used, and the Contractor had received a prior-approved waiver for U.S.-flag vessels for all foreign-flag ocean transportation; or

(4) Ocean transportation was used and some or all of the shipments were made on foreign-flag vessels without the written consent of DoD. The Contractor shall describe these shipments in the following format:

* ITEM DESCRIPTION CONTRACT LINE

ITEMS QUANTITY

TOTAL

(g) If this contract exceeds the simplified acquisition threshold and the final invoice does not include the required representation, the Government will reject and return it to the Contractor as an improper invoice for the purposes of the Prompt Payment clause of this contract. In the event there has been unauthorized use of foreign-flag vessels in the performance of this contract, the Contracting Officer is entitled to equitably adjust the contract, based on the unauthorized use.

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 11 OF 16 PAGES

(h) If the Contractor indicated in response to the solicitation provision, Representation of Extent of Transportation by Sea, that it did not anticipate transporting by sea any supplies; however, after the award of this contract, the Contractor learns that supplies will be transported by sea, the Contractor --

(1) Shall notify the Contracting Officer of that fact; and

(2) Hereby agrees to comply with all the terms and conditions of this clause.

(i) Subcontracts. In the award of subcontracts, for the types of supplies described in paragraph (b)(2) of this clause, including subcontracts for commercial products, the Contractor shall flow down the requirements of this clause as follows:

(1) The Contractor shall insert the substance of this clause, including this paragraph (i), in subcontracts that exceed the simplified acquisition threshold in part 2 of the Federal Acquisition Regulation.

(2) The Contractor shall insert the substance of paragraphs (a) through (e) of this clause, and this paragraph (i), in subcontracts that are at or below the simplified acquisition threshold in part 2 of the Federal Acquisition Regulation.

(End of clause)

52.249-1 TERMINATION FOR CONVENIENCE OF THE GOVERNMENT (FIXED-PRICE) (SHORT FORM) (APR 1984) FAR

52.249-8 DEFAULT (FIXED-PRICE SUPPLY AND SERVICE) (APR 1984) FAR

52.252-2 CLAUSES INCORPORATED BY REFERENCE (FEB 1998) FAR

As prescribed in 52.107(b), insert the following clause:

This contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at this/these address(es):

FAR: https://www.acquisition.gov/?q=browsefar DFARS: https://www.acq.osd.mil/dpap/dars/dfarspgi/current/index.html DLAD: http://www.dla.mil/HQ/Acquisition/Offers/DLAD.aspx

(End of clause)

52.253-1 COMPUTER GENERATED FORMS (DEVIATION 2026-O0038) (FEB 2026) FAR

252.204-7024 NOTICE ON THE USE OF THE SUPPLIER PERFORMANCE RISK SYSTEM (MAR 2023) DFARS

252.239-7098 PROHIBITION ON CONTRACTING TO MAINTAIN OR ESTABLISH A COMPUTER NETWORK UNLESS SUCH NETWORK IS DESIGNED TO BLOCK ACCESS TO CERTAIN WEBSITES---REPRESENTATION (DEVIATION 2021-O0003) (APR 2021) Include the following provision in all solicitations, including solicitations for the acquisition of commercial items under FAR part 12, that will use funds made available by the Consolidated Appropriations Act, 2021 (Pub. L. 116-260), or any other Act that extends to fiscal year 2021 funds the same prohibitions as contained in section 8116, division C, title VIII, of the Consolidated Appropriations Act, 2021 (Pub. L. 116-260).

(a) In accordance with section 8116 of Division C of the Consolidated Appropriations Act, 2021 (Pub. L. 116-260), or any other Act that extends to fiscal year 2021 funds the same prohibitions, none of the funds appropriated (or otherwise made available) by this or any other Act for DoD may be used to enter into a contract to maintain or establish a computer network unless such network is designed to block access to pornography websites. This prohibition does not limit the use of funds necessary for any Federal, State, tribal, or local law enforcement agency or any other entity carrying out criminal investigations, prosecution, or adjudication activities, or for any activity necessary for the national defense, including intelligence activities.

(b) Representation. By submission of its offer, the Offeror represents that it is not providing as part of its offer a proposal to maintain or establish a computer network unless such network is designed to block access to pornography websites.

(End of provision)

52.232-39 UNENFORCEABILITY OF UNAUTHORIZED OBLIGATIONS (JUN 2013) FAR

SECTION K - REPRESENTATIONS, CERTIFICATIONS AND STATEMENTS

52.207-4 ECONOMIC PURCHASE QUANTITY---SUPPLIES (AUG 1987) FAR

As prescribed in 7.203 , insert the following provision:

(a) Offerors are invited to state an opinion on whether the quantity(ies) of supplies on which bids, proposals or quotes are requested in this solicitation is (are) economically advantageous to the Government.

(b) Each offeror who believes that acquisitions in different quantities would be more advantageous is invited to recommend an economic purchase quantity.

If different quantities are recommended, a total and a unit price must be quoted for applicable items. An economic purchase quantity is that quantity at which a a significant price break occurs. If there are significant price breaks at different quantity points, this information is desired as well.

OFFEROR RECOMMENDATIONS

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 12 OF 16 PAGES

SECTION K - REPRESENTATIONS, CERTIFICATIONS AND STATEMENTS (CONTINUED)

ITEM QUANTITY PRICE QUOTATION TOTAL

(c) The information requested in this provision is being solicited to avoid acquisitions in disadvantageous quantities and to assist the Government in developing a data base for future acquisitions of these items. However, the Government reserves the right to amend or cancel the solicitation and resolicit with respect to any individual item in the event quotations received and the Government's requirements indicate that different quantities should be acquired.

52.209-2 PROHIBITION ON CONTRACTING WITH INVERTED DOMESTIC CORPORATIONS - REPRESENTATION (DEVIATION 2026-

O0038) (FEB 2026) FAR

As prescribed in 9.108-6(a), insert the following provision:

(a) Definitions. As used in this clause -- Inverted domestic corporation means a foreign incorporated entity that meets the definition of an inverted domestic corporation under 6 U.S.C. 395(b), applied in accordance with the rules and definitions of 6 U.S.C. 395(c).

Subsidiary means an entity in which more than 50 percent of the entity is owned --

(1) Directly by a parent corporation; or

(2) Through another subsidiary of a parent corporation.

(b) Government agencies are not permitted to use appropriated (or otherwise made available) funds for contracts with either an inverted domestic corporation, or a subsidiary of an inverted domestic corporation, unless the exception at 9.108-3(b) applies or the requirement is waived in accordance with the procedures at 9.108-5.

(c) Representation. The Offeror represents that-

(1) It [] is, [] is not an inverted domestic corporation; and

(2) It [] is, [] is not a subsidiary of an inverted domestic corporation.

52.209-11 REPRESENTATION BY CORPORATIONS REGARDING DELINQUENT TAX LIABILITY OR A FELONY CONVICTION UNDER

ANY FEDERAL LAW (DEVIATION 2026-O0038) (FEB 2026) FAR

As prescribed in 9.104-7(d), insert the following provision:

Representation by Corporations Regarding Delinquent Tax Liability or a Felony Conviction under any Federal Law (Deviation Date)

(a) The Government will not enter into a contract with any corporation that --

(1) Has any unpaid Federal tax liability that has been assessed, for which all judicial and administrative remedies have been exhausted or have lapsed, and that is not being paid in a timely manner pursuant to an agreement with the authority responsible for collecting the tax liability, where the awarding agency is aware of the unpaid tax liability, unless an agency has considered suspension or debarment of the corporation and made a determination that suspension or debarment is not necessary to protect the interests of the Government; or

(2) Was convicted of a felony criminal violation under any Federal law within the preceding 24 months, where the awarding agency is aware of the conviction, unless an agency has considered suspension or debarment of the corporation and made a determination that this action is not necessary to protect the interests of the Government.

(b) The Offeror represents that -

(1) It is [ ] is not [ ] a corporation that has any unpaid Federal tax liability that has been assessed, for which all judicial and administrative remedies have been exhausted or have lapsed, and that is not being paid in a timely manner pursuant to an agreement with the authority responsible for collecting the tax liability;

and

(2) It is [ ] is not [ ] a corporation that was convicted of a felony criminal violation under a Federal law within the preceding 24 months.

52.219-31 NOTICE OF SMALL BUSINESS RESERVE (MAR 2020) FAR

252.225-7000 BUY AMERICAN -- BALANCE OF PAYMENTS PROGRAM CERTIFICATE (FEB 2024) DFARS Basic. As prescribed in 225.601(1), use the following provision:

(a) Definitions. “Commercially available off-the-shelf (COTS) item,” “component,” “critical component,” “critical item,” “domestic end product,” “foreign end product,” “qualifying country,” “qualifying country end product,” and “United States,” as used in this provision, have the meanings given in the 252.225-7001, Buy American and Balance of Payments Program --Basic clause of this solicitation.

(b) Evaluation. The Government --

(1) Will evaluate offers in accordance with the policies and procedures of Part 225 of the Defense Federal Acquisition Regulation Supplement; and

(2) Will evaluate offers of qualifying country end products without regard to the restrictions of the Buy American statute or the Balance of Payments Program.

(c) Certifications and identification of country of origin.

(1) For all line items subject to the Buy American and Balance of Payments Program --Basic clause of this solicitation, the Offeror certifies that --

(i) Each end product, except those listed in paragraphs (c)(2) or (3) of this provision, is a domestic end product and that each domestic end product listed in

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 13 OF 16 PAGES paragraph (c)(4) of this provision contains a critical component or a critical item; and

(ii) For end products other than COTS items, components of unknown origin are considered to have been mined, produced, or manufactured outside the United States or a qualifying country. For those end products that do not consist wholly or predominantly of iron or steel or a combination of both, the Offeror shall also indicate whether these foreign end products exceed 55 percent domestic content, except for those that are COTS items. If the percentage of the domestic content is unknown, select “no”.

(2) The Offeror certifies that the following end products are qualifying country end products:

Line Item Number Country of Origin

(3) The following end products are other foreign end products, including end products manufactured in the United States that do not qualify as domestic end products. For those foreign end products that do not consist wholly or predominantly of iron or steel or a combination of both, the Offeror shall also indicate whether these foreign end products exceed 55 percent domestic content, except for those that are COTS items. If the percentage of the domestic content is unknown, select “no”.

Line Item Number Country of Origin (If known) Exceeds 55% Domestic

Content (yes/no)

&ZF_225_7000_081&

(4) The Offeror shall separately list the line item numbers of domestic end products that contain a critical component or a critical item (see Federal Acquisition Regulation 25.105).

Domestic end products containing a critical component or a critical item: Line Item Number [List as necessary]

252.225-7059 PROHIBITION ON CERTAIN PROCUREMENTS FROM THE XINJIANG UYGHUR AUTONOMOUS REGION --

REPRESENTATION (JUN 2023) DFARS

252.225-7966 PROHIBITION REGARDING RUSSIAN FOSSIL FUEL BUSINESS OPERATIONS - REPRESENTATION (CLASS

DEVIATION 2024-O0006, REVISION 1) (MAR 2024) DFARS

Use the following provision in solicitations that include the clause at 252.225-7967:

(a) Definitions. The terms business operations and fossil fuel company have the meanings given in the 252.225-7967 clause of this solicitation.

(b) Representation. By submission of an offer, the Offeror represents it is not, or that it does not knowingly have fossil fuel business operations with an entity or individual that is, 50 percent or more owned, individually or collectively, by --

(1) An authority of the government of the Russian Federation; or

(2) A fossil fuel company that operates in the Russian Federation, except if the fossil fuel company transports oil or gas --

(i) Through the Russian Federation for sale outside of the Russian Federation; and

(ii) That was extracted from a country other than the Russian Federation with respect to the energy sector of which the President has not imposed sanctions as of the date on which the contract is awarded.

52.240-90 SECURITY PROHIBITIONS AND EXCLUSIONS REPRESENTATIONS AND CERTIFICATIONS (DEVIATION 2026-O0038)

(FEB 2026) FAR

As prescribed in 40.205(a), insert the following provision:

(a) Definitions. As used in this provision- -- Backhaul, covered article, covered telecommunications equipment or services, critical technology, FASCSA order, Intelligence community, interconnection arrangements, national security system, roaming, sensitive compartmented information, sensitive compartmented information system, source, and substantial or essential component have the meanings provided in the clause 52.240-91, Security Prohibitions and Exclusions.

Business operations means engaging in commerce in any form, including by acquiring, developing, maintaining, owning, selling, possessing, leasing, or operating equipment, facilities, personnel, products, services, personal property, real property, or any other apparatus of business or commerce.

Marginalized populations of Sudan means --

(1) Adversely affected groups in regions authorized to receive assistance under section 8(c) of the Darfur Peace and Accountability Act (Pub. L. 109-344) (50

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 14 OF 16 PAGES

U.S.C. 1701 note); and

(2) Marginalized areas in Northern Sudan described in section 4(9) of such Act.

Restricted business operations means business operations in Sudan that include power production activities, mineral extraction activities, oil-related activities, or the production of military equipment, as those terms are defined in the Sudan Accountability and Divestment Act of 2007 (Pub. L. 110-174).

Restricted business operations do not include business operations that the person (as that term is defined in Section 2 of the Sudan Accountability and Divestment Act of 2007) conducting the business can demonstrate --

(1) Are conducted under contract directly and exclusively with the regional government of southern Sudan;

(2) Are conducted under specific authorization from the Office of Foreign Assets Control in the Department of the Treasury, or are expressly exempted under Federal law from the requirement to be conducted under such authorization;

(3) Consist of providing goods or services to marginalized populations of Sudan;

(4) Consist of providing goods or services to an internationally recognized peacekeeping force or humanitarian organization;

(5) Consist of providing goods or services that are used only to promote health or education; or

(6) Have been voluntarily suspended.

Sensitive technology --

(1) Means hardware, software, telecommunications equipment, or any other technology that is to be used specifically --

(i) To restrict the free flow of unbiased information in Iran; or

(ii) To disrupt, monitor, or otherwise restrict speech of the people of Iran; and

(2) Does not include information or informational materials the export of which the President does not have the authority to regulate or prohibit pursuant to section 203(b)(3) of the International Emergency Economic Powers Act (50 U.S.C. 1702(b)(3)).

(b) Procedures.

(1) Covered telecommunications and video surveillance. The Offeror shall review the list of excluded parties in the System for Award Management (SAM) at https://www.sam.gov for entities excluded from receiving federal awards for “covered telecommunications equipment or services.”

(2) FASCSA Orders.

(i) The Offeror shall search in SAM for the phrase “FASCSA order” for any covered article, or any products or services produced or provided by a source, if there is an applicable FASCSA order described in paragraph (e) of FAR 52.240-91, Security Prohibitions and Exclusions.

(ii) The Offeror shall review the solicitation for any FASCSA orders that are not in SAM but are effective and apply to the solicitation and resultant contract (see FAR 40.204-1(c)(2)).

(iii) FASCSA orders issued after the date of solicitation do not apply unless added by an amendment to the solicitation.

(c) Covered telecommunications equipment or services…