Sherwin Williams N11 00350 Sherwin Williams Seaguard 5000 HS Information Sheets.pdf

SEAGUARD® 5000 HS

EPOXY

P A N11B350 B P A N11B357 C U B P A N11W350 O W P A N11W357 C U O W P A N11R350 R P A N11R357 C U R P A N11A350 G P A N11A357 C U G P A N11H350 B P A N11H357 C U B P B N11V350 H

Protective

Marine Coatings

9.40Revised: March 31, 2022 www.sherwin-williams.com/protective

P D SEAGUARD 5000 HS EPOXY is a high performance and high solids, polyamine cured epoxy that is designed to be used as a part of an anticorrosive system for marine applications, or as a lining system for fuel, brine, ballast and non-potable water tanks.

• Complies with IMO Performance Standard for Protective Coatings SOLAS REGULATIONS II-1/3-2 and XII/6.3

• Corrosion resistant

• Outstanding adhesion

• Qualifi ed to MIL-PRF-24647 for underwater hull

• Qualifi ed to MIL-PRF-23236 for ballast tanks and fuel tanks

P C Finish: Low Sheen Color: Black, Off White, Red, Gray, and Buff Volume Solids: 73% ± 2% mixed Weight Solids: 79% ± 2% mixed VOC (EPA Method 24): <250 g/L; 2.08 lb/gal Mix Ratio: 1:1 by volume (2 components)

Recommended Spreading Rate per coat:

Minimum Maximum

Wet mils (microns) 7.0 (175) 10.0 (250) Dry mils (microns) 5.0 (125) 7.0 (175) ~Coverage sq ft/gal (m2/L) 167 (4.1) 234 (5.7) Theoretical coverage sq ft/gal (m2/L) @ 1 mil / 25 microns dft 1168 (28.6)

NOTE: Brush or roll application may require multiple coats to achieve maximum fi lm thickness and uniformity of appearance.

Drying Schedule @ 7.0 mils wet (175 microns):

35°F/1.7°C

50°F/10°C

77°F/25°C

110°F/43°C

50% RH

To touch: 8 hours 5 hours 4 hours 2 hours To recoat:

minimum: 24 hours 12 hours 6 hours 3 hours maximum*: 90 days 90 days 90 days 90 days

To cure: 20 days 14 days 7 days 7 days *Two weeks maximum for alkyd and urethane topcoats.

If maximum recoat time is exceeded, abrade surface before recoating.

Drying time is temperature, humidity, and fi lm thickness dependent.

Pot Life: 8 hours 6 hours 2 hours 1 hour Sweat-in-Time: None None None None Application of the antifouling coating shall occur while the epoxy coat is still tacky. Refer to the Application Bulletin for the defi nition of "TACKY".

Shelf Life: 36 months, unopened Store indoors at 40°F (4.5°C) to 100°F (38°C)

Flash Point (ADMIX): 110°F (43°C) PMCC Reducer: Not recommended* Clean Up: Reducer #130 (R7K130) *Contact your Sherwin-Williams representative for more information continued on back

R U For use as a coating for:

• Fuel, brine, ballast and non-potable water tanks

• Underwater hull

• Interior or exterior marine vessel applications

• Freeboard, topside, decks

• Acceptable for use with UHP / waterjetted substrates

• Use N11-350 series for Military/Government vessels or which require IMO PSPC approval

• Use N11-357 series for commercial vessels

P C

Substrate*: Steel Surface Preparation*: SSPC-SP10/NACE 2 System Tested*:

2 cts. SeaGuard 5000 HS Epoxy @ 5.0 mils (125 microns) dft/ct *unless otherwise noted below

Test Name Test Method Results Solvent Resistance ASTM D1308 Passed

Qualifi ed to MIL-PRF-23236, Type VI, Class 5 and 7, Grade C

Qualifi ed to MIL-PRF-24647, Type I, Class 1 and 2, Grade A and B, Application 1, 2 and 4

Qualifi ed to MIL-PRF-24647, Type II, Class 1, Grade A and B, Application 1, 2, 3 and 4

Tested by Det Norske Veritas (DNV). According to DNV Procedure, testing and classifi cation of ballast tank coatings, REV-02. Tested to the DNV Procedure over a Zinc Shop Primer Steel.

Received Highest Obtainable rating B1

Epoxy coatings may darken or yellow following application and curing.

P A N11B350 B P A N11B357 C U B P A N11W350 O W P A N11W357 C U O W P A N11R350 R P A N11R357 C U R P A N11A350 G P A N11A357 C U G P A N11H350 B P A N11H357 C U B P B N11V350 H

Protective

Marine Coatings

9.40Revised: March 31, 2022 www.sherwin-williams.com/protective

S P Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion.

Refer to product Application Bulletin for detailed surface prepara-tion information.

Minimum recommended surface preparation:

Immersion:

Iron & Steel / Aluminum SSPC-SP10/NACE 2, 2.0 mil (50 micron) profi le or NACE/SSPC WJ2(M) – with existing surface anchor profi le of >2.0 mils (>50 microns) Atmospheric:

Iron & Steel / Aluminum minimum: SSPC-SP2, SSPC-SP3 preferred: SSPC-SP6/NACE 3, 2.0 mil (50 micron) profi le or NACE/SSPC WJ2(M) – with existing surface anchor profi le of >2.0 mils (>50 microns) Galvanizing: SSPC-SP1

Surface Preparation Standards Condition of Surface

ISO 8501-1

BS7079:A1

Swedish Std.

SIS055900 SSPC NACE

White Metal Sa 3 Sa 3 SP 5 1 Near White Metal Sa 2.5 Sa 2.5 SP 10 2 Commercial Blast Sa 2 Sa 2 SP 6 3 Brush-Off Blast Sa 1 Sa 1 SP 7 4 Hand Tool Cleaning Rusted C St 2 C St 2 SP 2 -

Pitted & Rusted D St 2 D St 2 SP 2 - Power Tool Cleaning Rusted C St 3 C St 3 SP 3 -

Pitted & Rusted D St 3 D St 3 SP 3 -

T Do not tint.

A C Temperature: 35°F (1.7°C) minimum, 110°F (43°C) maximum (air, surface, and material) At least 5°F (2.8°C) above dew point Relative humidity: 85% maximum Refer to product Application Bulletin for detailed application information.

O I Packaging:

Part A: 1 gallon (3.78L) and 5 gallon (18.9L) containers Part B: 1 gallon (3.78L) and 5 gallon (18.9L) containers Weight:

Part A: 12.73 ± 0.2 lb/gal; 1.5 Kg/L Part B: 11.43 ± 0.2 lb/gal; 1.4 Kg/L Mixed: 12.08 ± 0.2 lb/gal; 1.45 Kg/L

S P Refer to the SDS sheet before use.

Published technical data and instructions are subject to change without notice.

Contact your Sherwin-Williams representative for additional technical data and instructions.

W The Sherwin-Williams Company warrants our products to be free of manufactur-ing defects in accord with applicable Sherwin-Williams quality control procedures.

Liability for products proven defective, if any, is limited to replacement of the defec-tive product or the refund of the purchase price paid for the defective product as determined by Sherwin-Williams. NO OTHER WARRANTY OR GUARANTEE

OF ANY KIND IS MADE BY SHERWIN-WILLIAMS, EXPRESSED OR IMPLIED,

STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING MER-

CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

P I R S

Dry Film Thickness / ct.

Mils (Microns) Steel or Aluminum, immersion:

2 cts. SeaGuard 5000 HS Epoxy 5.0-7.0 (125-175)

Steel or Aluminum, underwater hull:

2 cts. SeaGuard 5000 HS Epoxy 5.0-7.0 (125-175) 1-3 cts. SeaGuard Ablative Antifouling 2.5-4.0 (63-100) or 2 cts. SeaGuard 5000 HS Epoxy 4.0-8.0 (100-200) 2-3 cts. SeaVoyage Copper Free AF* 3.0-6.0 (75-150)

*SeaVoyage Copper Free Antifouling Paint must be applied over the epoxy primer, while the epoxy is still slightly tacky.

Steel or Aluminum, atmospheric:

1-2 cts. SeaGuard 5000 HS Epoxy 5.0-7.0 (125-175) 1-2 cts. Sherthane 2K 2.0-4.0 (50-100) or 1-2 cts. Polysiloxane XLE-80 HAPS Free 3.0-7.0 (75-175) or 1-2 cts. SeaGuard 1000 2.0-3.0 (50-75) or 1-2 cts. Hi-Solids Polyurethane 3.0-5.0 (75-125) Galvanized, atmospheric:

1 ct. SeaGuard 5000 HS Epoxy 4.0-7.0 (100-175) 1-2 cts. Sherthane 2K 2.0-4.0 (50-100) or 1-2 cts. Polysiloxane XLE-80 HAPS Free 3.0-7.0 (75-175) or 1-2 cts. SeaGuard 1000 2.0-3.0 (50-75) or 1-2 cts. Hi-Solids Polyurethane 3.0-5.0 (75-125)

Seawater Ballast Tank Applications In accordance with IMO Resolution MSC.215(82) PSPC, all application requirements specifi ed in PSPC Table 1 have to be strictly adhered to.

• Substrate: Abrasive blasting to Sa 2.5 (ISO 8501-1), SSPC-SP-10.

• Surface profi le: 30 - 75 microns as per ISO 8503-1/3.

• Water soluble contaminants: ≤ 50mg/m2 of sodium chloride. Conductivity measured in accordance with ISO 8502-9.

• Dry fi lm thickness: PSPC stipulates a Nominal Dry Film Thickness (NDFT) of 320 microns obtained in 2 coats. The fi lm thickness distribution is measured in accordance with the 90/10 rule.

• Maximum total dry fi lm thickness not to exceed 1000 mi-crons/40 mils.

• Coating sequence: Red, followed by light grey.

• Stripe coats: 2 strip coats in alternating colors must be ap-plied as part of the system.

The systems listed above are representative of the product's use, other systems may be appropriate.

D The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of The Sherwin-Williams Company.

Such information and recommendations set forth herein are subject to change and pertain to the product off ered at the time of publication. Consult your Sherwin- Williams representative to obtain the most recent Product Data Information and Application Bulletin.

P A N11B350 B P A N11B357 C U B P A N11W350 O W P A N11W357 C U O W P A N11R350 R P A N11R357 C U R P A N11A350 G P A N11A357 C U G P A N11H350 B P A N11H357 C U B P B N11V350 H

Protective

Marine Coatings

9.40Revised: March 31, 2022 www.sherwin-williams.com/protective

S P

Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion.

Iron & Steel / Aluminum, Immersion Service:

Remove all oil and grease from surface by Solvent Cleaning per SSPC-SP1. Minimum surface preparation is Near White Metal Blast Cleaning per SSPC-SP10/NACE 2, or NACE/SSPC WJ2(M).

For SSPC-SP10/NACE 2, blast clean all surfaces using a sharp, angular abrasive for optimum surface profi le (2.0 mils / 50 microns).

For NACE/SSPC WJ2(M), the existing surface anchor profi le should be >2.0 mils (>50 microns). Remove all weld spatter and round all sharp edges. Prime any bare steel the same day as it is cleaned.

Iron & Steel / Aluminum, Atmospheric Service:

Minimum surface preparation is Hand Tool Clean per SSPC-SP2.

For surfaces prepared by SSPC-SP2, fi rst remove all oil and grease from surface by Solvent Cleaning per SSPC-SP1. For better performance, use Commercial Blast Cleaning per SSPC-SP6/ NACE 3, or NACE/SSPC WJ2(M). For SSPC-SP6/NACE 3, blast clean all surfaces using a sharp, angular abrasive for optimum sur-face profi le (2.0 mils / 50 microns). For NACE/SSPC WJ2(M), the existing surface anchor profi le should be >2.0 mils (>50 microns).

Prime any bare steel the same day as it is cleaned.

Galvanized Steel:

Allow to weather a minimum of six months prior to coating. Solvent Clean per SSPC-SP1 (recommended solvent is VM&P Naphtha).

When weathering is not possible, or the surface has been treated with chromates or silicates, fi rst Solvent Clean per SSPC-SP1 and apply a test patch. Allow paint to dry at least one week before test-ing adhesion. If adhesion is poor, brush blasting per SSPC-SP7 is necessary to remove these treatments. Rusty galvanizing requires a minimum of Hand Tool Cleaning per SSPC-SP2, prime the area the same day as cleaned.

Previously Painted Surfaces If in sound condition, clean the surface of all foreign material.

Smooth, hard or glossy coatings and surfaces should be dulled by abrading the surface. Apply a test area, allowing paint to dry one week before testing adhesion. If adhesion is poor, or if this product attacks the previous fi nish, removal of the previous coating may be necessary. If paint is peeling or badly weathered, clean surface to sound substrate and treat as a new surface as above.

Surface Preparation Standards Condition of Surface

ISO 8501-1

BS7079:A1

Swedish Std.

SIS055900 SSPC NACE

White Metal Sa 3 Sa 3 SP 5 1 Near White Metal Sa 2.5 Sa 2.5 SP 10 2 Commercial Blast Sa 2 Sa 2 SP 6 3 Brush-Off Blast Sa 1 Sa 1 SP 7 4 Hand Tool Cleaning Rusted C St 2 C St 2 SP 2 -

Pitted & Rusted D St 2 D St 2 SP 2 - Power Tool Cleaning Rusted C St 3 C St 3 SP 3 -

Pitted & Rusted D St 3 D St 3 SP 3 -

A B A C

Temperature: 35°F (1.7°C) minimum, 110°F (43°C) maximum (air, surface, and material) At least 5°F (2.8°C) above dew point

Relative humidity: 85% maximum

A E

The following is a guide. Changes in pressures and tip sizes may be needed for proper spray characteristics. Always purge spray equipment before use with listed reducer. Any reduction must be compliant with existing VOC regulations and compatible with the existing environmental and application conditions.

Reducer ............................Not recommended* Clean Up ..........................Reducer #130, R7K130

Airless Spray Pressure.........................2400 psi Hose...............................1/4" ID Tip ...................................017" - .031" Filter ...............................60 mesh Reduction .......................Not recommended*

Brush Brush..............................Natural Bristle Reduction .......................Not recommended*

Roller Cover .............................3/8" - 1/2" woven with solvent resistant core Reduction .......................Not recommended*

*Contact your Sherwin-Williams representative for more information

If specifi c application equipment is not listed above, equivalent equipment may be substituted.

continued on back

P A N11B350 B P A N11B357 C U B P A N11W350 O W P A N11W357 C U O W P A N11R350 R P A N11R357 C U R P A N11A350 G P A N11A357 C U G P A N11H350 B P A N11H357 C U B P B N11V350 H

Protective

Marine Coatings

9.40Revised: March 31, 2022 www.sherwin-williams.com/protective

A B A P

Surface preparation must be completed as indicated.

Mix contents of each component thoroughly with low speed power agitation. Make certain no pigment remains on the bottom of the cans. Then combine one part by volume of Part A with one part by volume of Part B. Thoroughly agitate the mixture with power agitation. Re-stir before using.

Apply paint at the recommended fi lm thickness and spreading rate as indicated below:

Recommended Spreading Rate per coat:

Minimum Maximum

Wet mils (microns) 7.0 (175) 10.0 (250) Dry mils (microns) 5.0 (125) 7.0 (175) ~Coverage sq ft/gal (m2/L) 167 (4.1) 234 (5.7) Theoretical coverage sq ft/gal (m2/L) @ 1 mil / 25 microns dft 1168 (28.6)

NOTE: Brush or roll application may require multiple coats to achieve maximum fi lm thickness and uniformity of appearance.

Drying Schedule @ 7.0 mils wet (175 microns):

35°F/1.7°C

50°F/10°C

77°F/25°C

110°F/43°C

50% RH

To touch: 8 hours 5 hours 4 hours 2 hours To recoat:

minimum: 24 hours 12 hours 6 hours 3 hours maximum*: 90 days 90 days 90 days 90 days

To cure: 20 days 14 days 7 days 7 days *Two weeks maximum for alkyd and urethane topcoats.

If maximum recoat time is exceeded, abrade surface before recoating.

Drying time is temperature, humidity, and fi lm thickness dependent.

Pot Life: 8 hours 6 hours 2 hours 1 hour Sweat-in-Time: None None None None Application of the antifouling coating shall occur while the epoxy coat is still tacky. Refer to the Application Bulletin for the defi nition of "TACKY".

Application of coating above maximum or below minimum recommended spreading rate may adversely aff ect coating performance.

C U I Clean spills and spatters immediately with Reducer #130, R7K130.

Clean tools immediately after use with Reducer #130, R7K130.

Follow manufacturer's safety recommendations when using any solvent.

D The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of The Sherwin-Williams Company.

Such information and recommendations set forth herein are subject to change and pertain to the product off ered at the time of publication. Consult your Sherwin- Williams representative to obtain the most recent Product Data Information and Application Bulletin.

P T Stripe coat all crevices, welds, and sharp angles to prevent early failure in these areas.

When using spray application, use a 50% overlap with each pass of the gun to avoid holidays, bare areas, and pinholes. If necessary, cross spray at a right angle.

Spreading rates are calculated on volume solids and do not include an application loss factor due to surface profi le, roughness or po-rosity of the surface, skill and technique of the applicator, method of application, various surface irregularities, material lost during mixing, spillage, overthinning, climatic conditions, and excessive fi lm build.

Excessive fi lm build, poor ventilation, and cool temperatures may cause solvent entrapment and premature coating failure.

For Immersion Service: (if required) Holiday test in accordance with ASTM D5162 for steel, or ASTM D4787 for concrete.

Do not apply the material beyond recommended pot life.

Do not mix previously catalyzed material with new.

In order to avoid blockage of spray equipment, clean equipment before use or before periods of extended downtime with Reducer #130, R7K130.

Material must be at least 50°F/10°C prior to catalyzing.

Application of the antifoulant coating shall occur when the last coat of epoxy anticorrosive is still tacky. If the epoxy is hard, apply a tack coat of epoxy anticorrosive at 1-2 mils (25-50 microns) WFT over previously painted surfaces. "Tacky" is defi ned as that curing (drying) stage when a fi ngertip pressed lightly against the fi lm leaves only a slight impression and none of the fi lm sticks to the fi nger.

Application of solvent based alkyd coating, such as MIL-PRF-24635, shall be applied when the epoxy is "dry to the touch, but not fully cured." (For example prior to 7 days @ 77°F/25°C).

Refer to Product Information sheet for additional performance characteristics and properties.

S P Refer to the SDS sheet before use.

Published technical data and instructions are subject to change without notice.

Contact your Sherwin-Williams representative for additional technical data and instructions.

W The Sherwin-Williams Company warrants our products to be free of manufacturing defects in accord with applicable Sherwin-Williams quality control procedures.

Liability for products proven defective, if any, is limited to replacement of the de-fective product or the refund of the purchase price paid for the defective product as determined by Sherwin-Williams. NO OTHER WARRANTY OR GUARANTEE

OF ANY KIND IS MADE BY SHERWIN-WILLIAMS, EXPRESSED OR IMPLIED,

STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING MER-

CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.