Section_VII_Attachments_Exhibit_A.pdf

SECTION VII - Attachments

CITY OF PHOENIX

SECTION VII - Attachments

EXHIBIT A- CITY OF PHOENIX SPECIFICATION GUIDE

FOR LOCKSMITH SERVICES HARDWARE

SECTION 08 71 00 - DOOR HARDWARE-CITY OF PHOENIX SPECIFICATION GUIDE

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including the Masterformat Architectural Standard General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY

A. This Section includes the following:

1. Commercial door hardware for the following:

a. Swinging doors

b. Non-fire-rated sliding doors

c. Non-fire-rated folding doors

d. Other doors to the extent indicated

e. City of Phoenix building standards for door locks, key cylinders, finish hardware and accessories for doors

2. Cylinders for doors are specified in later sections of this document.

B. Related Sections include the following:

1. Division 08 11 13 Section "Hollow Metal Doors and Frames"

2. Division 08 11 16 Section "Aluminum Frames"

3. Division 08 14 16 Section "Flush Wood Doors"

4. Division 08 Section "All-Glass Entrances and Storefronts" for entrance door hardware, except cylinders

5. Division 10 Section "Wire Mesh Partitions" for hardware for doors in wire mesh partitions, except cylinders

6. Division 06 10 00 "Rough Carpentry"

C. Product coordination, purchasing, delivering, and scheduling remain requirements of this Section. Products furnished, but not installed, under this Section include the following:

Solicitation No. IFB 22-044 Page 75 of 94

SECTION VII - EXHIBITS

CITY OF PHOENIX

C. Manual Flush Bolts: BHMA A 156.16, Grade 1; designed for mortising into door edge.

1. Acceptable Manufacturers:

a. McKinney

b. Trimco (TBM).

c. Ives

2.9 EXIT DEVICES

A. 1. Von Duprin Manufacturing Company; an Allegion company. Use 33/35 or 98/99 Series. No Substitutions. Vertical rod applications are not acceptable, unless building code dictates usage. Utilize mullions in place of vertical rods.

1) Von Duprin Exit Device Trim:

a. 98/99 - use 996L lever trim

b. 33/35 - use 370L lever trim

2. Sargent Manufacturing Company; an Assa Abloy Group company. Sargent 80 Series. No Substitutions. Vertical rod applications are not acceptable, unless building code dictates usage. Utilize mullions in place of vertical rods.

2) Sargent Exit Device Trim:

b. Add 43 to the part number for flush end cap.

3. For Von Duprin and Sargent panic devices, order appropriate "64-" mortise or rim cylinders from Sargent for each device.

a. Sargent 64-42 Mortise Cylinder with appropriate cam for hardware function.

b. Use Sargent 64-34 rim cylinder for Von Duprin and Sargent rim devices.

No vertical rods permitted. Mullion required.

4. All non-fire rated devices must be lock cylinder dogging type.

B. Accessibility Requirements: Where handles, pulls, latches, locks, and other operating devices are indicated to comply with accessibility requirements, comply with the U.S. Architectural & Transportation Barriers Compliance Board's "Americans with Disabilities Act (ADA),

1. Provide operating devices that do not require tight grasping, pinching, or twisting of the wrist and that operate with a force of not more than 5 lbs.

C. Exit Devices for Means of Egress Doors: Comply with NFPA 101. Exit devices shall not require more than 15 lbs. to release the latch. Locks shall not require use of a key, tool, or special knowledge for operation.

D. Exit Devices: Listed and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction, for panic protection, based on testing according to

UL 305.

Solicitation No. IFB 22-044 Page 84 of 94