SF30 Amendment 001 of Solicitation.pdf

Offers must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended, by one of the following methods:

(a) By completing items 8 and 15, and returning or (c) By separate letter or electronic communication which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGMENT TO BE RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by letter or electronic communication, provided each letter or electronic communication makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

E. IMPORTANT: Contractor is not is required to sign this document and return copies to the issuing office.

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT 1. CONTRACT ID CODE

2. AMENDMENT/MODIFICATION NUMBER 3. EFFECTIVE DATE 4. REQUISITION/PURCHASE REQUISITION NUMBER 5. PROJECT NUMBER (If applicable)

7. ADMINISTERED BY (If other than Item 6) CODE

STANDARD FORM 30 (REV. 11/2016)

Prescribed by GSA FAR (48 CFR) 53.243

FACILITY CODE

9A. AMENDMENT OF SOLICITATION NUMBER

9B. DATED (SEE ITEM 11)

10A. MODIFICATION OF CONTRACT/ORDER NUMBER

10B. DATED (SEE ITEM 13)

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of Offers is extended. is not extended.

12. ACCOUNTING AND APPROPRIATION DATA (If required) copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted;

13. THIS ITEM APPLIES ONLY TO MODIFICATIONS OF CONTRACTS/ORDERS.

IT MODIFIES THE CONTRACT/ORDER NUMBER AS DESCRIBED IN ITEM 14.

CHECK ONE A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE CONTRACT ORDER

NUMBER IN ITEM 10A.

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, appropriation data, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(b).

C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF:

D. OTHER (Specify type of modification and authority)

Except as provided herein, all terms and conditions of the document referenced in Item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15C. DATE SIGNED

15A. NAME AND TITLE OF SIGNER (Type or print)

16C. DATE SIGNED

16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

PAGE OF PAGES

6. ISSUED BY CODE

8. NAME AND ADDRESS OF CONTRACTOR (Number, street, county, State and ZIP Code) (X)

CODE

15B. CONTRACTOR/OFFEROR

(Signature of person authorized to sign)

16B. UNITED STATES OF AMERICA

(Signature of Contracting Officer)

Previous edition unusable

Amanda B. Foley

The Industrial Plant Equipment (IPE) Technical Requirement Documents (TRDs) have been amended to reflect the correction to CLIN 22. The voltage requirement was incorrectly listed at 308 and is hereby corrected to 208. See the corrected TRD document attached.

No other changes at this time.

Acquisition Division 2300 Main Street Kansas City, MO 64108

QSDM-J3-223010-A

6/15/2022

ID47QSHE22K0001

1 3

CLIN 22:

ITEM NOUN: CUTTING SYSTEM, WATER JET

NSN: 3419015250135

REQUISITION: FE652102700014

Specifications/Technical Characteristics:

● MAXIMUM OPERATING

PRESSURE

50000.0 POUNDS PER SQUARE INCH ABSOLUTE

● MOUNTING TYPE FLOOR

● CURRENT TYPE AC

● ELECTRIC MOTOR

HORSEPOWER RATING

30.0

● TABLE OVERALL LENGTH 126.000 INCHES NOMINAL ; up to 2" variance

● TABLE OVERALL WIDTH 65.000 INCHES NOMINAL ; up to 2" variance

● TABLE LONGITUDINAL

TRAVEL

100.000 INCHES NOMINAL ; up to 2" variance

● TABLE CROSS TRAVEL 55.000 INCHES NOMINAL ; up to 2" variance

● PHASE THREE

● SPECIAL FEATURES

▪ 380-440 VAC, 50-60HZ / 3 PHASE;

▪ 30HP AT 50,000PSI;

▪ 3/4 YD HOPPER;

▪ SYS DRIVE 1/2 HP;

▪ OPERATES UNATTENDED;

▪ NOISE LEVEL BELOW 80 DBA FOR SUBMERGED CUTTING;

▪ SPEED 200 IPM;

▪ CNTRL CONSOLE 110V;

▪ REMOTE/LOCAL CONTROL

● FREQUENCY IN HERTZ 50.0 AND 60.0

● Two (2) hard copies and one (1) electronic copy of technical data shall be provided with the machine.

● Shipping address for electronic technical data packages is:

Attn: Brian Roberson, Equip. Specialist 235 Byron Street, (Bldg. 300) Suite 19A Robins AFB, GA 31098-1813

If not specified within the characteristics of the NSN, please provide the following information:

● The existing source power available at the facility is o Volt: ___208__VAC o Phase: __3____ o Frequency: __50/60___Hz

● The machine must fit through a doorway with the following dimensions:

o Width: _12__FEET o Height: _12___FEET

● Available floor space for equipment width by length to include required operator workspace and OSHA required access clearances to service panels.

o Width: __25____ FEET o Length: __25_____ FEET

Note 1: This will be an open competitive competition and the source of supply will not be determined until the vendor quotes and technical acceptability is reviewed by the contracting agency.

Note 2: We the USAF do not include installation, training, tooling or any additional options that are not part of the standard package in the above characteristics data.