Attachment_F15_-_Federal_Specification_KKK-A-1822F_SIN_212X_GM_2015.pdf

STANDARD ITEM 212X

EXPORT

GM Chassis

FY 2015

Ambulance, Type II, in accordance with Federal Specification for Ambulances, KKK-A-1822F, dated August 1, 2007 (including change notices number 1 thru 6) and the following additional requirements:

1.1 SCOPE

The ambulance covered by this document is listed by standard item number. The item description, minimums, options and manufacturer data can be viewed in the Federal Vehicle Standards.

3.6.3.1 POWER UNIT

The power unit and associated fuel system shall be fully compatible with B20 fuel

3.6.4.3 AIR POLLUTION CONTROL

The vehicle or engine model year shall conform to 40 CFR Subchapter C-Part 86 - “Control of Emissions from New and In-use Highway Vehicles and Engines, as evidenced by an EPA certificate of compliance. The certificate of compliance shall be made available upon request.

3.6.7 WHEELS. Wheels shall be painted the same paint color as the lower body.

3.6.8 TIRES Each tire shall be equipped with a visual indicator or monitoring system that indicates tire pressure.

3.7.1.1 WARNING INDICATORS.

An audible alarm shall be furnished that activates with the required visual warning indicators

Two waterproof, Cole Hersee Model 90030, buttons mounted one on each side of the vehicle's beltline, at the rear corners, to alert driver while backing. When pressed, the buttons shall activate audible alarm with a continuous sound. Buttons shall be accessible for replacement. Buttons shall be labeled “DRIVER BACKING ALARM”, with a permanent plate that is fastened to the body.

3.7.2 WIRING INSTALLATION.

All electrical panels shall be readily accessible for servicing.

All battery and heavy power leads added by the FSAM shall be SGX wire with crimped, water proofed, sealed, terminals.

3.7.7.2 PORTABLE EQUIPMENT CHARGING CIRCUIT

The leads shall terminate as follows:

One in the cab behind the driver’s seat One in the action area

3.7.8 125 VOLT AC UTILITY POWER.

The GFCI shall be located so that it is easily accessible to the vehicle operator.

GM Chassis

FY 2015

A weather resistant illuminated switch shall be furnished to connect the block heater to the 125 volt system. The control switch and pilot light shall be in the cab. The switch shall be identified with a permanent plate as the control for the block heater.

All 125-volt power inlets shall be the autoeject type

3.8.1.2 GROUND LIGHTING.

The ambulance shall be equipped with lighting that is capable of providing illumination at a minimum level of 0.3fc on ground areas within 30 inches of the edge of the ambulance in areas designed for personnel to climb into or onto the ambulance or descend from the ambulance to the ground level. All ground lighting shall be LED.

3.8.2 AMBULANCE EMERGENCY LIGHTING.

The emergency lighting shall be a 14 light LED system, Whelen KKKELED1

3.8.3 FLOOD AND LOADING LIGHT (EXTERIOR).

The exterior flood and load lighting shall be Whelen 9SC0ENZR, LED gradient opti-scene lights

3.8.4 AMBULANCE INTERIOR LIGHTING.

Interior lighting shall include:

Two separately protected, three position (High, Off, Low) switches to control the patient compartment lights, Lights to be Whelen LED.

Two additional flush mount Whelen 20C0CCCR 4” white LED lights shall be furnished for "Vehicle checkout" Lights shall be controlled by a five minute, timer. Lights shall be connected directly to B+ through the timer.

High intensity cot light

LED Action Area Light

3.9.6 BUMPERS AND STEPS. A folding rear step with an all steel substructure shall be provided .

3.10.3 EMSP SEATING.

Shall be EVS Model 1850, Adjustable front to rear.

3.10.4 PATIENT COMPARTMENT INTERIOR DIMENSIONAL PARAMETERS.

The interior dimension from rear door to front bulkhead shall be 130" nominal.

The headroom dimension shall be a minimum of 66 inches.

3.10.6 AMBULANCE BODY STRUCTURE.

GM Chassis

FY 2015

Only stainless steel hinges, latches, and hardware, etc. shall be used. All dissimilar metals shall include a Mylar or other dielectric medium between metals.

3.10.8.1 PROTECTION OF PATIENTS AND CREW.

Occupant Restraint Device

The front end of the squad bench shall have a net type occupant restraint device to assist in restraining seat belted occupants in the event of a rapid de-acceleration. The device shall be compliant with SAE J1948

The minimum dimensions of the device shall cover the area from within three (3) inches of the top of the seat base to within four (4) inches of the ceiling, and from the vertical surface at the aisle edge of the squad bench to within two (2) inches of the curbside wall. The surface of the net shall be designed to form a concave, retentive shape upon impingement by an individual.

The device shall have a minimum of seven (7) recessed points of attachment to the body structural members as follows: two (2) points) at the ceiling, two (2) points on the bottum, and three(3) points at the curbside wall. The attachment devices used shall be quickly removable for cleaning without tools.

The mounting hardware shall be tested by applying a force of 6,000 lb horizontally –0 to +15 degrees in a forward direction at a maximum rate of 300 lb per second and holding the force for 6,000 lb for 10 seconds. The mounting hardware shall not fail. Deformation of structural components does not constitute failure.

3.10.11 FLOOR COVERINGS AND COLOR.

Floor covering shall be Lonplate II. Color shall be No. 424, Gunmetal

3.10.16 INTERIOR SURFACES.

The action wall shall be finished in white ABSor laminate.

The counter-top shall be covered with ABS and shall have a minimum 1/2 inch lip. The walls and ceilings shall be white and shall provide easy access for service of wiring, oxygen lines, etc.

NOTE: Absorbent material such as carpeting, fabric, or inside/outside plastic type carpeting, etc., that resists cleaning and decontamination shall not be used in any storage or patient compartment. Wood or wood products shall not be used for any interior sub-surfaces including cabinet’s, structure, trim panels, and doors.

All interior cabinets, compartments and storage areas shall be fabricated from fiberglass reinforced composite material, Thermalite or equal, and shall be laminated on both sides with white high pressure plastic.

3.11.1.2 WASTE AND SHARPS DISPOSAL.

GM Chassis

FY 2015

A crash stable sharps receptacle and compartment/storage area, minimum 1 gallon, shall be furnished for retention of a sharps container that meets OSHA requirements, A waste receptacle shall be furnished.

All sharps receptacle and waste receptacle openings shall be covered with a red hinged cover indicating the type of waste they are to contain.

3.11.3 STORAGE COMPARTMENTS AND CABINETS DESIGN

All interior cabinets shall be 12 inches deep nominal at the floor, and have the maximum possible volume.

All interior compartment shelves shall have identical construction.

All sliding doors shall be clear Lexan or equal, minimum 3/16" thick. The Lexan shall have all exposed edges rounded.

All cabinets shall:

1. Be constructed of fiberglass reinforced composite material (Thermalite or equal)

2. Laminated with white high pressure plastic on both sides.

3. Be sealed at all intersection panels.

3.11.4 PATIENT COMPARTMENT SEATING

Shall be for 2 persons in addion to the EMSP.

3.11.7 IV HOLDER FOR INTRAVENOUS FLUID CONTAINERS

Two devices shall be furnished

3.12 OXYGEN, MAIN SUPPLY AND INSTALLATION

Ohio Diamond type fittings required.

Oxygen shall be controlled by a low pressure, solenoid valve, switched from the action wall. A green pilot light integral with the switch shall be provided to indicate the valve is "ON". A labeled "Emergency Oxygen Bypass" valve shall also be provided in a visible, recessed, easily accessible location.

A remote oxygen indicator for main bottle shall be LED, Liquid Crystal or multi-light type. The indicator shall include an audible low pressure warning alarm with a switch to disable alarm. The indicator panel shall be located on the EMSP's action wall.

3.13.3 AIR CONDITIONING CRITERIA.

All non chassis manufacturer supplied A/C lines & fittings shall be Aeroquip E-Z clip type.

3.13.4 VENTILATION CRITERIA.

A power exhaust vent with a labeled electronic speed control or rheostat and "ON/OFF" illuminated switch, with both located on the EMSP panel, shall be furnished. A shutter or adjustable louver shall be furnished

GM Chassis

FY 2015

on the interior of the power vent system. Mounting of vent on the exterior shall be flush when located on the side of the body.

3.13.5 ENVIRONMENTAL CONTROLS.

All added heater lines shall be silicone rubber or high temperature EDPM/Nomex hose that is specifically approved by and connected per the chassis manufacturer for ambulance applications

3.14.2 RADIO (MOBILE) PROVISIONS. A 12V, 40 amp., circuit breaker protected lead ( wired to B+ sw) that terminates in a pair of insulated, shielded terminals one (1) each, behind the driver and passenger seats, shall be furnished. Additionally, a ground terminal shall be furnished and shall be located next to each of the above terminals.

3.14.3 ANTENNA, CABLE, AND MOUNTING. Two antenna leads shall be furnished.

3.14.4 SIREN-PUBLIC ADDRESS SYSTEM.

Shall be a Whelen WS-295 HFS, with dual speakers. Siren shall have "rapid yelp" and "air horn”.

3.15.1 ADDITIONAL EQUIPMENT

1. DC Battery Conditioner shall be Vanner 30-10 GFI, or equal

2. High intensity cot light located near the head of primary cot shall include a ceiling mounted, LED light (Whelen 80C0EECR, in a near flush style mounting.

3. Patient Fan shall be located in an area towards the rear of the street side splint cabinet, providing a minimum of 250 CFM rating, with protective grille for the fan blades. A switch on the EMSP panel and speed control rheostat on fan shall be furnished. Fan shall be a Maradyne Model 3000- 12 or equal.

4. Front and Rear commercial duty type mud flaps.

5. An LED map lightw/flexible shaft shall be furnished in the cab.

6. Medical Equipment Rail System.

7. Electric clock. Intellitec Emergency Time Manager.

8. Sphygmomanometer, shall be rail mounted. Obese, adult, child, and pediatric cuffs shall be furnished that interconnect with furnished unit.

9. Oxygen flowmeter (pressure compensated) with mounting space for a humidifier shall be provided for primary patient

10. Cot fastener mounting assembly shall be for a Ferno 93ES cot.

11. A CO detector shall be furnished in the patient compartment

12. An additional console shall be furnished between the driver and passenger seat. The console shall attach to the OEM engine cover utilizing OEM mounts. The console shall be fabricated from formed and welded aluminum sheet, minimum .090. The console shall have (2) cup holder’s minimum 3.5” X 3”. The console shall be painted black.

13. .

14. (2) USB charging outlets shall be provided in the cab console area.

15. Any Velcro type material used to install trip panels and/or cushions shall be the hard nylon hook and loop design SJ3526/27 or equal.

16. Any air accumulation tanks, such as air horn, tire chains or rear air suspension, shall have automatic heated air drains

3.15.2 STANDARD EQUIPMENT.

1. Fire Extinguishers to be furnished with rigid quick release, crash stable, brackets designed for automotive application.

GM Chassis

FY 2015

The type Fire Extinguishers to be furnished are:

1 ABC dry chemical 1 C02 (Carbon Dioxide)

The brackets are not to be mounted. The brackets are to be shipped loose with the extinguishers.

2. One Safety Vision SV-LCD70RP back-up system (or equal) including one color backup camera and one color monitor, minimum 5”, mounted in cab headliner to the rear of the rear view mirror shall be furnished and installed.

3.16.2 COLOR, PAINT AND FINISH.

Top Markings. The "Star of Life" marking on a square reflective background is acceptable.

GM Chassis

FY 2015

3.19 GSA FORM 1398

The FSAM shall affix one copy of GSA Form 1398, GSA Purchased Vehicle, fully completed, to left front compartment door inner panel after the final inspection is successfully completed at the FSAM’s plant. All marks on windows and other labels (except the Morony label and labels cautioning against drained transmission, crankcase, and rear axle) shall be removed. Copies of GSA Form 1398 are available from the Contracting Officer. Alternately, FSAM’s may reproduce this form locally in its entirety at their own expense. The form shall be printed on white polyester laser S4900 acrylic 70# mr / face w1970 white 2 mil polyster or equal.

NOTE TO OFFEROR: Data shown in the Agency Name block in the Agency Bureau section of the MVDO shall be utilized to complete the receiving agency block of the GSA Form 1398.

Receiving Agency—Examples are: DEFENSE DEPT-NAVY, INTERIOR DEPT, FAS, Etc.

FOB

MONTH YEAR

MONTHS MILES

DATE

2.25 by 4.5 inches Nominal

GSA PURCHASED VEHICLE

RECEIVING AGENCY

CONTRACT NUMBER

RPN NUMBER

INSERT ALL DATA ABOVE AND APPLY THIS LABEL TO THE BACK OF THE

DRIVER's VISOR OR PLACE IN GLOVE BOX AFTER FINAL INSPECTION IS MADE.

REMOVE ALL LABELS AND MARKS FROM WINDOWS AND WINDSHIELD EXCEPT

THE MORONY LABEL AND THE LABELS CAUTIONING AGAINST DRAINED OIL IN

TRANSMISSION, CRANKCASE AND REAR AXLE.

NOTE TO CONTRACTOR

MANUFACTURER'S SERIAL NUMBER

DATE

OF

DELIVERY

WARRANTY

INSPECTED BY

GSA Form 1398 (Rev. 3-13)

GM Chassis

FY 2015

4. QUALITY ASSURANCE PROVISIONS

FIRST PRODUCTION AMBULANCE INSPECTION. the first production ambulance shall be inspected. This first ambulance shall be completely representative of the balance of the vehicles to be delivered under the contract. The purpose of the inspection shall determine vehicle conformity to the contract. The ambulance shall be inspected by the contractor at his plant under the direction and in the presence of purchaser’s representative(s). Inspections shall be conducted during normal weekday working hours. The cost of inspections, examination, all tests, and vehicle support, exclusive of personal expenses incurred by participating purchaser’s representatives shall be borne by the contractor. Acceptance of the first production vehicle shall not constitute a waiver by the purchaser of any rights under the provisions of the contract.

SOURCE INSPECTION. Ambulance(s) shall be inspected upon completion by the purchaser prior to shipment from manufacturer’s factory or assembly plant. The inspection shall consist of the following:

a. Workmanship inspection

b. Quality conformance inspection

CRITERIA OF CERTIFICATIONS.

The first production vehicle shall be tested and certified to KKK-A-1822F by a nationally recognized independent testing lab approved by the Government.

The independent test lab shall be An ISO/IEC 17025 accredited laboratory by an accreditation body that is recognized by the National Cooperation for Laboratory Accreditation (NACLA) or is a signatory to the International Laboratory Accreditation Cooperation (ILAC) Mutual Recognition Arrangement (MRA). The scope of accreditation for the lab shall include a statement that specifies that the lab is granted accreditation to perform AMD tests 1-25.

The tests shall include all requirements of KKK-A-1822F, performance tests and AMD tests 1, 3- 25.

The use of existing certifications is acceptable provided they meet all criteria in section 4.

the existing certifications must be submitted with their proposal.

The government reserves the right to approve the testing and/or analytical method of validation.

The independent test lab shall be ISO 9001-2000 certified.

The existing certifications must be submitted with their proposal.

NOTE: Body(s) used to complete AMD tests 1, 3, & 4 and all dynamic testing is considered a used product and shall not be furnished to the government

ADDITIONAL DOCUMENTATION REQUIRED WITH OFFER

Additional Warranty Coverage Documents A document that shows that the FSAM holds ISO 9001-2000 certification A document showing that the FSAM holds MVP status as defined by the National Truck

Equipment Association (NTEA).

An NTEA Ultra Mod Weight Dist. & Center of Gravity Calculation A document that shows that the ISO/IEC 17025 accredited laboratory under contract is granted accreditation to perform AMD tests 1-25.

GM Chassis

Detailed exterior and interior scaled drawings of the standard unit are required. At a minimum these drawings shall include:

1. All specified dimensions listed in the Federal Specification for Ambulances, KKK-A-1822 and the minimum requirements specified by the Government.

2. 5 exterior views (Right Side Elevation, Left Side Elevation, Front Elevation, Rear

Elevation, and Plan Views).

3. 3 interior views (Patient Compartment Front elevation, curbside & street side elevation).

These drawings shall include all mounted items that are specified by the minimum requirements.

4. The location of the electrical compartment and the oxygen compartment.

5. The location of the emergency warning lights.

6.2.1 WARRANTY COVCERAGE

The following additional warranty coverage shall be furnished:

Lifetime Cabinet Warranty Lifetime Electrical Wiring, Wiring Components, Printed Circuit Wiring Boards, printed wiring boards, and Wiring installation warranty.

5 year Prorated Paint Warranty

AUTOCHOICE ORDERING DATA

Purchasers should select the required ambulance and options from AUTOCHOICE at:

www.gsa.gov/automotive. AUTOCHOICE is GSA Automotive’s on-line vehicle ordering system.

The following codes are used to identify the availability of options in the Federal Vehicle Standards and AutoChoice:

a) S= Standard

b) SA= Stand Alone

c) PKG= Package (includes, requires or excludes other options)

d) N/A= Not Available

PRECAUTIONS AND OBSERVATIONS

Due to the variety of ambulance models this standard must cover, the purchasers are cautioned that the options offered herein are subject to manufacturer’s changes or availability. Most special requirement items are not offered as assembly line or factory options. Therefore, if special features or non-standard equipment is desired, procurement locally of such items after the vehicle is contracted for or received is often more advantageous. Reference the manufacturer’s data books and brochures before ordering vehicle(s) with special requirements.

PROCEDURE TO IDENTIFY VEHICLES AND OPTIONS

The payload/passenger requirements determine the model and GVWR of vehicle desired They are available in AUTOCHOICE at: www.gsa.gov/automotive.

GM Chassis

DEVIATION FROM FEDERAL STANDARD NO. KKK-A-1822F

Systems or equipment not identified in these requirements shall be identified as special requirements. Contact the appropriate Contract Specialist to determine availability. All non-standard/special equipment is reviewed by GSA Engineering to determine the appropriate application.

The agency head of his/her designee shall determine which vehicle requires specific additional systems or equipment considering the following:

a) Climate conditions prevailing in the area of operation.

b) Effect on vehicle operational capabilities.

c) Special terrain requirements

d) Availability of maintenance and service facilities.

e) Fuel availability and cost.

f) Delivery delays of completed vehicle, due to customizing specified.

OPTIONS

The following Option Code detailed requirements are offered for selected Ambulance options. Option codes apply only as indicated in AutoChoice and the federal vehicle standards.

NOTE: SELECTING SOME OPTIONS MAY RESULT IN THE MINIMUM REQUIREMENTS FOR

A STANDARD ITEM NOT BEING COMPLIED WITH!!

CODE “K43” DAVID CLARK INTERCOM SYSTEM

When Option K43 is specified, A David Clark series 3800 vehicle intercom system shall be furnished in lieu of the specified system. The system shall be furnished and installed per Figure DCC Series 3800 VIS unless otherwise specified.

CODE “K05” BASIC MEDICAL PACKAGE

When code K05 is specified, a basic medical package shall be furnished that includes the following:

1. K09 - Inverter

2. Flow meter for Secondary Patient

3. Cot-FW Model 93ES. Other cots may be substituted for the 93ES (see K06) or the cot may be deleted (see K07)

4. Backboards, high density plastic/Polymer w/skids (on long boards only) and quick clips, including 5 straps for long boards and 3 straps for short boards.

5. Portable Oxygen Unit, Amvex model # GR-540-DMDM or equal, 50PSI w/ 2 DISS and 2 “D” cylinders with 2 Zico Q-R-D2 holders

6. A portable suction aspirator

7. An Adult CPR Bag Valve Mask (BVM) shall be furnished. BVM shall be equipped with a port that allows oxygen delivery

The suction aspirator shall be capable of operation from the vehicle’s 12 volt DC electrical system. It shall also operate from an integral battery supply which is rechargeable and which will allow the unit to meet the air flow and suction requirements of this paragraph for at least 20 minutes of continuous operation. The portable suction aspirator shall provide an air flow of at least 30 liters per minute at the end of the suction tube and a vacuum level of at least 300 mm Hg to be reached within 4 seconds after the tube is clamped. The portable aspirator shall be provided with the following accessories:

GM Chassis

FY 2015

one suction rinsing water bottle one nonmetallic pharyngeal suction tip with thumb suction control port of sufficient diameter to allow aspiration of semi-solid gastric contents

The suction tubing shall be translucent and shall not kink or collapse under high suction. The inside diameter of the tubing shall be at least .64 mm (1/4"). The other suctioning catheters shall be provided by the user. The internal battery supply shall be rechargeable from the vehicle’s 12-volt DC electrical system and from 125 volts AC. The 125-volt AC charging system need not be integral to the portable suction unit. The unit shall be provided with applicable power cords and plugs

The 12-volt power point in the interior compartment with exterior access will be of the type that matches the charging cord for the portable aspirator furnished.

Other than K09, the equipment furnished as a part of this option will be shipped loose in the back of the ambulance. It is the customer’s responsibility to mount and/or store the equipment according to the manufacturer’s directions.

CODE “K09” INVERTER

When code K09 is specified, a Vanner 20-1050CUL/CULW AC Power System shall be furnished

CODE “K15” RED CROSS MARKINGS(FOR MILITARY & EXPORT ONLY)

When code K15 is specified, the following additional markings shall be furnished:

1. The legend "AMBULANCE" in block blue letters on a white field not less than 6 inches in height shall be centered between "STAR OF LIFE" and Red Cross on each side of the vehicle.

2. A block type, blue "STAR OF LIFE", not less than 16 inches, shall be on the right and left side panels. A block type, blue "STAR OF LIFE", not less than 12 inches, shall be on the rear..

3. A premasked Red Cross, on a white field, not less than 16 inches shall be on the right and left side panels. A premasked 12 inch Red Cross, on a white field, shall be on the on the rear. The legend "AMBULANCE" in block type blue letters, on a white field, not less than 4 inches in height shall be centered between "STAR OF LIFE" and Red Cross on the rear of the vehicle .

4. The only roof marking shall consist of a premasked 36 x 36 inch Red Cross on a 42 x 42 inch white field centrally located on the roof panel.

GM Chassis

FY 2015

CODE “MIL” MILITARY DATA PLATES

When code MIL is specified, the following shall be furnished:

1. Data Plate. A data plate only shall be furnished. No other exterior military markings shall be furnished.

At a minimum, the Data Plate shall be as follows:

2. A DD FORM 250 (MATERIAL INSPECTION AND RECEIVING

REPORT) shall be furnished in lieu of a GSA form 308.

CODE “K21” SEVERE WEATHER PACKAGE.

When K21 is specified “Reflextex” insulation shall be furnished in walls and ceiling, in addition to standard required insulation. The underside of the patient compartment area shall be spray foam insulated.

All cold weather operation equipment that the OEM offers shall be furnished

CODE “CPT” PAINT-CUSTOM COLOR

This option must be specified when ordering paint colors other than the standard white and the 2 following military colors.

SPECIAL PAINT (TONEDOWN GREEN)

Paint shall be in accordance with MIL-T-1223AC (Para. 3.7.1) Markings Data Plates, etc. and 3.6.6. Paint Finish and Color. Vehicles are exempt from exterior markings, registration numbers and contract number are still required on data plate. Tonedown Paint Color 24052 of FED. STD-595 is required. The OEM bumpers shall be black painted steel.

SPECIAL PAINT (DESERT SAND)

Paint shall be in accordance with MIL-T-1223AC (Para. 3.7.1) Markings Data Plates, etc. and 3.6.6. Paint Finish and Color. Vehicles are exempt from exterior markings, registration numbers and contract number

NOMENCLATURE _____________________________________________

MAKE AND MODEL _____________________________________________

CHASSIS SERIAL NUMBER (VIN) __________________________________

VEHICLE CURB WEIGHT: __________________________________KG (LBS)

PAYLOAD, MAXIMUM: ___________________________________KG (LBS)

GROSS VEHICLE WEIGHT RATING, MAX._____________________KG (LBS)

GROSS COMBINATION WEIGHT RATING, MAX._________________KG (LBS)

DATE OF DELIVERY: ________________MONTH________________YEAR

WARRANTY: ____________MO. ____________________________KM (MILES)

CONTRACT NUMBER ___________________________________________

RPN NUMBER _________________________________________________

US PROPERTY

GM Chassis

FY 2015

are still required on data plate. Commercial Color Paint Dessert Sand Color 30313 of FED STD-595 is required. The OEM bumpers shall be black painted steel.

CODE “DCAM” DRIVING CAMERA

When DCAM is specified, a Digital Ally DVM-250 or equal shall be furnished and installed.

CODE “CBU4” 4 WAY CAMERA SYSTEM

When code CBU4 is specified, a 4 Camera System - Safety Vision SV-LCD70RP or equal shall be furnished and installed. This shall include:

1. 1 color backup camera

2. 1 cylinder camera, mounted above the rear entry doors facing the patient compartment

3. 2 fender cameras mounted 1 each front fender facing rearward wired to activate with left and right turn signals

4. 1 color monitor, minimum 5”, mounted cab headliner to the rear of the rear view mirror

CODE “RBV” RUNNING BOARDS

When code RBV is specified, there shall be LED lights positioned in the forward aspect of the modular body to illuminate the running boards.

CODE “PSMA” AIR FORCE PARTS AND SERVICE MANUALS

When code PSMA is specified, the following shall be provided in a complete package:

The Contractor/Vendor shall provide two (2) complete sets of manuals (1 paper and 1 electronic) to include, operators, parts and service manuals to the U.S. Air Force Program Office at the address listed below. Manuals shall be for the complete vehicle and include any mounted or accessory equipment. The data formats shall be paper (printed), and electronic (CD ROM).

Those files provided in electronic format must be complete and assembled separately in a “print on demand” format such that a bound paper copy can be produced and provided with no security restrictions (unlocked). No “auto run” or “executable files” are acceptable.

For each set of manuals, the Contractor/Vendor shall provide one copy of Form DD250 Material Inspection and Receiving Report available at http://www.dtic.mil/whs/directives/infomgt/forms/eforms/dd0250.pdf to the U.S. Air Force Program Office at the below listed address.

All data shall be supplied in accordance with DFARS clause 252.227-7015 TECHNICAL DATA— COMMERCIAL ITEMS (MAY 2013). The Contractor/Vendor shall provide the U.S. Air Force Program Office at the address listed below a Government Purpose License Agreement to allow the reproduction of the data they supply in agreement with the above referenced DFARS clause.

The shipping address for the above required technical data packages is:

235 BYRON STREET (BLDG300)

GM Chassis

FY 2015

SUITE 19A

Robins AFB, GA 31098-1813 Attn: 404 SCMS/GUEEA