Attachment_G32_-_DOD_JSLEVES_Vehicle_Branding_Guide_March_2017.pdf

Department of Defense Joint Service Law Enforcement

Vehicle Equipment Standardization

Vehicle Branding Guide March 2017

Figure 2-33. Law Enforcement Sedan

TO 36-1-191

Figure 2-34. Security Forces SUV

CAUTION

MILITARY WORKING DOG

CAUTION: MILITARY WORKING DOG

1075592430A Typewritten Text

Figure 2-35. Security Forces Pickup Truck

CAUTION

MILITARY WORKING DOG

CAUTION: MILITARY WORKING DOG

Vehicle Wrap - Car

Driver Side

Passenger Side

Rear

Car Specifications:

Blue stripe will start midway above the front tire and curve over the back tire ending at least 5” away from the rear light.

Blue stripe will be positioned under the door handles.

“Dial 9-1-1” text will align with the end of the stripe at the rear light. Note: If different, overseas bases will replace 911 with local emergency number.

SF Badge will sit on side of text closest to the front of the vehicle

SF Badge and “POLICE” text will be the same hieght

• Shield Size:11” tall

• Police Text Size: 11” tall

• Overall Design Length: 145.5” wide

• Police Text - Rear: 7” tall, 28.5” wide

Font-Faces:

Dial 9-1-1 Text - TW Cen MT Condensed Police Text - This text has been modified from it’s original font face. Please use the lettering from the art files.

Color:

Police Text Outline and “Dial 9-1-1” Dark Navy Blue: Pantone 282 C or a color of similar hue and value

Vehicle Wrap - SUVs

SUV Specifications:

curve over the back tire ending at least 5” away from the rear light.

Blue stripe will be positioned under the door handles.

“Dial 9-1-1” text will align with the end of the stripe at the rear light.

SF Badge will sit on side of text closest to the front of the vehicle

SF Badge and “POLICE” text will be the same hieght

Rear - The text should be placed in the upper left corner of the lift gate just below the window or center at the bottom of the lift gate.

• Shield Size:10.5” tall

• Police Text Size: 10.5” tall

• Overall Design Length: 140” wide

• Police Text - Rear: 3” tall, 12.25” wide

Color:

Police Text Outline and “Dial 9-1-1” Dark Navy Blue: Pantone 282 C or a color of similar hue and value

Font-Faces:

Dial 9-1-1 Text - TW Cen MT Condensed Police Text - This text has been modified from it’s original font face. Please use the lettering from the art files.

Vehicle Wrap - Trucks

Truck Specifications:

curve over the back tire ending at least 5” away from the rear light.

Blue stripe will be positioned under the door handles.

“Dial 9-1-1” text will align with the end of the stripe at the rear light.

SF Badge will sit on side of text closest to the front of the vehicle

SF Badge and “POLICE” text will be the same hieght

• Shield Size:11” tall

• Police Text Size: 11” tall

• Overall Design Length: 171” wide

• Police Text - Rear: 7” tall, 28.5” wide

Font-Faces:

Dial 9-1-1 Text - TW Cen MT Condensed Police Text - This text has been modified from it’s original font face. Please use the lettering from the art files.

Color:

Police Text Outline and “Dial 9-1-1” Dark Navy Blue: Pantone 282 C or a color of similar hue and value above referenced DANGER sign having a red background with DO NOT OPERATE BOOM ABOVE 80 DEGREES FROM THE HORIZONTAL PLANE in 5/16-inch white let-ters.

2.78.2 “NO RIDERS”. All forklifts shall have “NO RID- ERS” in 2-inch black letters, stenciled vertically on both up-rights of the fork frame, facing the operator (Figure 2-32).

NOTE

When forklift upright size and/or hydraulic line placement will not accommodate placement of standard markings, local management will stencil “NO RIDERS” in minimum 1-inch black letters at a location easily seen by the operator.

2.78.3 Rollerized Vehicle Beds. Rollerized vehicle beds

(K-Loaders and flatbed trailers) will have the legend “WATCH STEP” applied on the walkway at each end of the rollerized beds. When “WATCH STEP” legend conflicts with “HARNESS REQUIRED AREA” and associated yellow line marking, refer to Figure 2-8 for proper legend placement.

The legend will be stenciled in 3-inch or 1-3/4-inch letters (depending on space availability) at approximately one foot intervals beginning at each end of the rollerized bed and extending inward for 4 feet. The legend will be applied us-ing yellow paint on black and green surfaces and black paint on yellow surfaces.

2.79 CONTINENTAL OR LYCOMING AIR-COOLED

ENGINES.

All vehicles equipped with Continental or Lycoming air-cooled engines will have the auxiliary engine oil, which is specified in the applicable technical order, either stenciled or taped on a body panel near the engine, or on the access door to the engine, using 1/2-inch letters. When applying this in-formation by stenciling, use white paint on red surfaces and black paint on yellow surfaces. When using tape, apply red tape with silver numbers.

EXAMPLE:

Auxiliary Engine Oil Specifications Grade

2.80 MARKING SECURITY FORCES VEHICLES.

The base Defense Force Commander (DFC) will approve/ deny all requests for Security Forces markings and, when approved, coordinate the vehicle add-on letter with the ve-hicle management office (or equivalent) for filing in the ve-hicles records jacket prior to execution. Vehicle markings will not deviate from the specifications outlined in this chap-ter. The DFC has the authority to determine if no markings will be applied to vehicles identified for unmarked purposes.

At no time will only “some” markings be applied. Changes to Security Forces markings will be accomplished through attrition (e.g., vehicle replacement, accident repair, etc.) Se-curity Forces will be responsible for all costs associated with marking their vehicles, to include damages that may have occurred due to markings.

NOTE

Due to differences in vehicles (i.e., size of fenders, doors, and other panels), letter size and location/ size of security forces shields may vary if the in-tended location does not allow enough space for application.

2.80.1 Marking Law Enforcement Sedans. Law en-

forcement sedans shall be marked as follows: The text “Po-lice” with the Security Forces badge decal alongside of the text closest to the front of the vehicle will be centered be-tween the front and rear wheel well. All markings will be made using a temporary adhesive type material (example:

magnetic or 3M vinyl), easily removable without damaging painted surfaces. Security Forces badges will be on a white or olive drab background, depending on vehicle color and local requirements. Markings must be uniform as described below and illustrated in Figure 2-33.

• Blue stripe will start midway above the front tire and curve over the back tire ending at least 5 inches away from the rear light. The beginning of the stripe will measure 5 inches wide and taper to 2.5 inches when curving over the rear wheel. Blue stripe will be positioned under the door handles and run paral-lel with the natural body lines of the vehicle.

• “Dial 9-1-1” Text Size: 4 inches letters and align with the end of the stripe at the rear light.

• Security Forces Badge Size: 11 inches tall

• “Police” Text - Sides: 11 inches letters

• “Police” Text - Rear: 7 inches letters

Font-Faces:

• “Dial 9-1-1” Text - TW Cen MT Condensed

• “Police” Text - Bolt Bold

Color:

• “Police” text background and “Dial 9-1-1” text will be: Dark Navy Blue, Pantone 282 C or a color of similar hue and value

Change 7 2-23

• Striping: 3mm reflective blue (3M 68CR or similar vinyl stock with same color key)

• “Police” text: 3mm reflective white (#680CR-10) or a color of similar hue and value

• Security Forces Badge: 3mm reflective white (#680CR-10) or a color of similar hue and value

2.80.2 Security Forces SUVs. Security Forces SUVs

used for security duties shall be marked as follows: The text “Police” with the Security Forces badge decal alongside of the text closest to the front of the vehicle will be centered between the front and rear wheel well. All markings will be made using a temporary adhesive type material (example:

magnetic or 3M vinyl), easily removable without damaging painted surfaces. Security Forces badges will be on a white or olive drab background, depending on vehicle color and local requirements. Markings must be uniform as described below and illustrated in Figure 2-34.

• Blue stripe will start midway above the front tire and curve over the back tire ending at least 5 inches away from the rear light. The beginning of the stripe will measure 5 inches wide and taper to 2.5 inches when curving over the rear wheel. Blue stripe will be positioned under the door handles and run paral-lel with the natural body lines of the vehicle.

• “Dial 9-1-1” Text Size: 4 inches letters and align with the end of the stripe at the rear light.

• Security Forces Badge Size: 11 inches tall

• “Police” Text - Sides: 11 inches letters

• “Police” Text - Rear: 3 inches letters. The text should be placed in the upper left corner of the lift gate just below the window or center at the bottom of the lift gate.

Font-Faces:

• “Dial 9-1-1” Text - TW Cen MT Condensed

• “Police” Text - Bolt Bold

Color:

• “Police” text background and “Dial 9-1-1” text will be: Dark Navy Blue, Pantone 282 C or a color of similar hue and value

• Striping: 3mm reflective blue (3M 680CR or simi-lar vinyl stock with the same color key)

• “Police” text: 3mm reflective white (#680CR-10) or a color of similar hue and value

• Security Forces Badge: 3mm reflective white (#680CR-10) or a color of similar hue and value

2.80.3 Marking Security Forces Pickup Trucks. Secu-

rity Forces pickup trucks (2-door and 4-door) used for secu-rity duties shall be marked as follows: The text “Police” with the Security Forces badge decal alongside of the text closest to the front of the vehicle will be centered between the front wheel well and the rear of the main cabin. All markings will be made using a temporary adhesive type material (example:

magnetic or 3M vinyl), easily removable without damaging painted surfaces. Security Forces badges will be on a white or olive drab background, depending on vehicle color and local requirements. Markings must be uniform as described below and illustrated in Figure 2-35.

• Blue stripe will start midway above the front tire and curve over the back tire ending at least 5 inches away from the rear light. The beginning of the stripe will measure 5 inches wide and taper to 2.5 inches when curving over the rear wheel. Blue stripe will be positioned under the door handles and run paral-lel with the natural body lines of the vehicle.

• “Dial 9-1-1” Text Size: 4 inches letters and align with the end of the stripe at the rear light.

• Security Forces Badge Size: 11 inches tall

• “Police” Text - Sides: 11 inches letters

• “Police” Text - Rear: 7 inches letters

Font-Faces:

• “Dial 9-1-1” Text - TW Cen MT Condensed

• “Police” Text - Bolt Bold

Color:

• “Police” text background and “Dial 9-1-1” text will be: Dark Navy Blue, Pantone 282 C or a color of similar hue and value

• Striping: 3mm reflective blue (3M 680CR or simi-lar vinyl stock with the same color key)

• “Police” text: 3mm reflective white (#680CR-10) or a color of similar hue and value

• Security Forces Badge: 3mm reflective white (#680CR-10) or a color of similar hue and value

2.80.4 Optional Markings. The base Defense Force Com-

mander (DFC) may authorize the use of the following op-tional markings:

2-24 Change 7

• Such items as crime stop programs bumper stickers, dare program stickers, etc., may be applied to the bumpers, light bars or located on the rear windows such that the sticker does not affect rearward vision, nor should it cover the center mounted stop light.

• “Dial 9-1-1” text will align with the end of the stripe at the rear light.

NOTE

If different, overseas bases will replace 911 with local emergency number.

• When authorized by the DFC, military working dog magnetic reflective stenciling may be applied to metallic assemblies or vinyl reflective stenciling may be applied to rear-side windows. Additional re-flective stencils will mark Security Forces vehicles used for transporting military working dogs. Exact markings will be, CAUTION: MILITARY WORK- ING DOG. The word caution must be centered be-low the blue stripe if so equipped; military working dog will be stenciled below. Markings for vehicles other than four door sedans and trucks will be marked in a similar fashion centered on the front portion of the rear quarter panel.

2.80.5 Security Forces HMMWVs. Security Forces

HMMWVs used for security duties shall be marked as fol-lows: Security Forces badge decal will be centered on both front doors using a temporary adhesive type material (Ex-ample: magnetic or 3M vinyl), easily removable without damaging painted surfaces. Security Forces badge will be on an olive drab background. Rear/side markings will read “Po-lice” and be applied on both side panels, flush with the top of the bed rails or centered on the rear hatch deck lid sides, as applicable, with 4-inch black letters. No additional mark-ings will be applied to the vehicle.

2.81 ALERT, REFLEX, BASE OPS, AND BASE

CIVIL ENGINEER (FIRE MARSHAL).

Marking of these and other vehicles requiring specific iden-tification will be accomplished by use of a detachable de-vice. The mounting bar NSN 2540-00-409-8878 may be used when approved by AFELM VEMSO.

2.82 “FOLLOW ME” VEHICLES.

The “FOLLOW ME” sign will be painted white, reflective, FSN 8010-965-2500.

2.83 LOW VISIBILITY MARKING, SNOW REMOVAL

EQUIPMENT.

All snow removal equipment will be outlined to indicate height, length, and width using silver reflective tape con-forming to ASTM-D4956, Type II, Class 3, Type 1, color G.

2.84 MARKING EXPLOSIVE ORDINANCE DIS-

POSAL VEHICLES.

These vehicles may be equipped with rotating warning lights, as well as sirens. When warning lights and sirens are used, they will be installed on a removable mounting bar NSN 2540-00-409-8878. The abbreviated legend E.O.D. will be applied to a metal backing plate in 2-inch silver reflective letters on a red background and affixed to the front and rear of the mounting bar. The type of lights and color of lenses will be in accordance with local or state laws regarding op-eration of emergency vehicles or, in cases of overseas opera-tion, in compliance with status of forces or host nation agreements.

NOTE

This guidance takes precedence over TO 36-1-161 or TO 36-1-171.

2.84.1 EOD Vehicles Under Contract Number GS-

30F-1046D. EOD vehicles purchased under GSA, manufac-tured by Emergency One, Inc., may retain the organizational markings that were on the vehicle at the time of acceptance by base-level vehicle management.

2.84.2 Retaining “USAF EOD” in Large Lettering. The

following vehicle registration numbers will be allowed to retain the large lettering on the sides of the body that reads “USAF EOD”. These registration numbers include those al-ready authorized in paragraph 2.84.1, as well as the recent deliveries. Future EOD procurements WILL NOT have the unauthorized style of markings. 04C00292 - 00293, 05C00043 - 00056, 06C01093, 07C80009, 08C00026 - 00028, 08C00369, 08C00391 - 00393, 09C00168 - 00175.

2.85 MARKING VEHICLES EQUIPPED WITH

MS51335 AND CID A-A-52550 SERIES PINTLE

HOOKS.

All vehicles (except toned down) equipped with a manual release pintle hook, MS51335 and CID A-A-52550 series, will be marked as illustrated in Figure 2-22 using 1/2-inch silver or white reflective letters on a red background. Toned down vehicles will be marked utilizing a non-reflective decal with 1/2-inch black letters, color number 37038, on green background, color number 24052, or clear background. Units choosing to mark vehicles with towing capacities, use letter size and color scheme as mentioned above. Markings shall be applied with stencil or other suitable method and placed in the general area of the pintle hook. Proper towing capaci-ties should be obtained from the end item TO.

NOTE

Vehicles using pintle hooks (Holland PH30) with the automatic secondary locking device, the above decal is not required.

Change 7 2-25

JSLEVES Army Standardized Graphic – Highlighted white/gray areas are for local installation use only and not for JSLEVES Graphics.

(2) 4-3/8” MILITARY (black with gold boundary)

(2) 6” POLICE (Black with gold boundary)

(2) 119” Long Green (Pantone: R0 G67 B25) /Gold (C0 M5 Y100 K0) Graphic

(2) 1.75” ASSIST • PROTECT • DEFEND

(2) 11”inches, “Dial 911” (Green with gold [yellow] lettering)

(1) 6” inches, “Dial 911” (Green with gold [yellow] lettering)

(1) Rear facing “MILITARY” using black lettering with gold boundary

(1) Rear facing “POLICE” using gold lettering with green background

Materiel: 3M or equivalent micro prismatic (reflective” material with included UV filtering laminate. Graphics will utilize a removable adhesive.

(1) Rear-facing, 4”inches, “retro-reflective” markings in green and gold alternating 45 degree angle down and away “chevron” pattern

JSLEVES Army Standardized Graphic – Highlighted white/gray areas are for local installation use only and not for JSLEVES Graphics.

POLICE

MARINE CORPS

POLICE

MARINE CORPS

19-4057 TCX (True Blue) 18-1662 TCX (Scarlet Red) 15-1142 TCX (Gold)

C=96 M=96 Y=11 K=42

C=0 M=10 Y=95 K=3

C=58 M=49 Y=44 K=13

C=1 M=98 Y=94 K=0

U.S. Navy Police/ Dial 911 Decal Font:

Rockwell Extra Bold Regular Rockwell Extra Bold Regular