710302542-00.pdf

A A

B B

SIZE DWG NO REV

SHEET 1 OF 2

FINISH

CHECKED

TITLE

AN EMPLOYEE OWNED COMPANY

ORRVILLE, OH

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF THE

WILL-BURT COMPANY ANY

REPRODUCTION IN PART OR WHOLE

WITHOUT THE WRITTEN PERMISSION OF

THE WILL-BURT COMPANY IS PROHIBITED.

DRAWN

MATERIAL UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES.

APPROVALS DATE

PROPRIETARY AND CONFIDENTIAL

TOLERANCES ON DECIMALS ANGLES

0 = ± 0.030 ± 1/2° 00 = ± 0.010 000 = ± 0.005

FRACTIONAL ± 1/64"

1. ALL INSIDE EDGES TO HAVE

.005" TO .035" FILLETS.

2. ALL OUTSIDE EDGES TO HAVE

.005" TO .015" CHAMFER OR RADIUS.THIRD ANGLE PROJECTION PN:

APPROX. WT:N/A 710302542 00B8/25/2015

710302542

C:\_Vault-WF\Inventor\710000000\710302542.idw

WILL-BURT

msmith

ON ALL MACHINED SURFACES

PNEU MAST 5.5-25 HDNL

HRDC W/T CE CUSTOM

X2

BOM

ITEM P/N DESCRIPTION QTY

1 5264201 TOP SEC 5.5-25 HDNL Ø3.75" HRDC W/T 1

2 5264301 INT SEC 6H 5.5-25 HDNL Ø4.50" HRDC W/T 1

3 5264302 INT SEC 6H 5.5-25 HDNL Ø5.25" HRDC W/T 1

4 5264303 INT SEC 6H 5.5-25 HDNL Ø6.00" HRDC W/T 1

5 5264304 INT SEC 6H 5.5-25 HDNL Ø6.75" HRDC W/T 1

6 5264401 INT SEC 8H 5.5-25 HDNL Ø7.50" HRDC W/T 1

7 5264402 INT SEC 8H 5.5-25 HDNL Ø8.25" HRDC W/T 1

8 5264501 BASE SEC 5.5-25 HDNL Ø9" HRDC W/T 1

9 4006506 TOP TUBE STOP ASM 3.75 HDR HRDC W/T 1

10 4362208 INSERT COLLAR ASM 4.50 NL HARDCOAT W/T 1

11 4362209 INSERT COLLAR ASM 5.25 NL HARDCOAT W/T 1

12 4362210 INSERT COLLAR ASM 6.00 NL HARDCOAT W/T 1

13 4362211 INSERT COLLAR ASM 6.75 NL HARDCOAT W/T 1

14 5287703 COLLAR ASM HDNL 8 HOLE 7.5" HRDC WT 1

15 5287702 COLLAR ASM HDNL 8 HOLE 8.25" HRDC WT 1

16 5287701 COLLAR ASM HDNL 8 HOLE 9" HRDC WT 1

17 900702 LW 3/8 SSTL 48

18 902642 COLLAR BOLT 48

19 902356 SEAL RUBBER 3.75 1

20 902357 SEAL RUBBER 4.50 1

21 902358 SEAL RUBBER 5.25 1

22 902359 SEAL RUBBER 6.00 1

23 902360 SEAL RUBBER 6.75 1

24 902361 SEAL RUBBER 7.50 1

25 902362 SEAL RUBBER 8.25 1

26 900059 EXPANDER 3.75" 1

27 900060 EXPANDER 4.50" 1

28 900061 EXPANDER 5.25" 1

29 900062 EXPANDER 6.00" 1

30 900063 EXPANDER 6.75" 1

31 900064 EXPANDER 7.50" 1

32 900065 EXPANDER 8.25" 1

33 900091 BACK UP WASHER 3-3/4" HD TUBE (CLR ADZ) 1

34 900092 BACK UP WASHER 4-1/2" HD TUBE (CLR ADZ) 1

35 900093 BACK UP WASHER 5-1/4" HD TUBE (CLR ADZ) 1

36 900094 BACK UP WASHER 6" HD TUBE (CLR ADZ) 1

37 900095 BACK UP WASHER 6-3/4" HD TUBE (CLR ADZ) 1

38 900096 BACK UP WASHER 7-1/2" HD TUBE (CLR ADZ) 1

39 900097 BACK UP WASHER 8-1/4" HD TUBE (CLR ADZ) 1

40 5267001 ORIFICE BOLT-NO HOLE SSTL 1

41 912721 ORIFICE BOLT-.19 HOLE SSTL 1

42 912722 ORIFICE BOLT-.38 HOLE SSTL 2

43 5267002 ORIFICE BOLT-.56 HOLE SSTL 3

44 902419 WEAR RING 3.75 1

45 902420 WEAR RING 4.50 1

46 902421 WEAR RING 5.25 1

BOM

ITEM P/N DESCRIPTION QTY

47 902422 WEAR RING 6.00 1

48 902423 WEAR RING 6.75 1

49 902424 WEAR RING 7.50 1

50 902425 WEAR RING 8.25 1

51 900147 LW Ø1.0 INT TOOTH 7

52 902851 IDENTIFICATION PLATE 1

53 901414 DRIVE SCREW #4 x 1/4 SSTL 2

54 900567 PIPE PLUG 3/8 NPT HEX SOC SSTL 1

55 901669 PIPE PLUG 0.375 NPT SQ HD PLASTIC 1

56 913918 LABEL, MAST KIT-H.D/N.L. CE * 1

57 902853 HARDWARE BAG-HEAVY DUTY * 1

58 902982 MAST DRAIN KIT * 1

59 5060702 MAG. WARNING KIT 12V (GRI SWITCH) * 1

60 911646 CRATE, SHIPPING-EXPORT * 1

61 TP-5288401 PNEUMATIC MAST MANUAL PAE 5.5-25' HDNL 1

REVISION HISTORY

ECN REV DESCRIPTION DATE APPROVED

12808 00 INITIAL RELEASE 8/25/2015 MS/

N E

S

TE

D (5

.5 ' O

R

.7 M

EX

TE

N D

E D

(2 5'

O R

.6

M

(9.0)

52 53

(3 3)

(*) INDICATES THAT ITEM IS NOT SHOWN ON DRAWING.

STAMP A 1/8 HIGH "O" ON ONE KEY OF EACH MAST SECTION BELOW

COLLAR & ON COLLAR ABOVE BOLT OF MARKED KEY.MARK BASE

MAST SECTION (NO KEY) IN LINE WITH OTHER SECTIONS.

STAMP SERIAL No. IN 1/8 HIGH NUMBERS.

USE TEF-GEL ON ALL COLLAR BOLTS AND TORQUE TO 100-120 in.lbs.

MAST WT.= 200 lbs. APPROX.

INSTALL & ALLOW 1/4±1/16 SPACE BETWEEN ENDS OF WEAR RINGS.

REFERENCE DRAWING B-41545 FOR ALL LABEL LOCATIONS.

ADD 2 WRAPS OF THREAD TAPE TO EACH ORIFICE BOLT.

APPLY MAGNALUBE G OR EQUAL TO TUBE I.D. AND SEAL.

COMPLETELY COVER THE TREADS OF THE FOUR 1/4-20 TOP TUBE

STOP SCREWS WITH LOCTITE 242

THIS MAST IS EQUIPPED WITH

STANLESS STEEL ORIFICE BOLTS

TEF-GEL ON COLLAR BOLTS

MAST MANUAL TP-5288401

(HARDCOAT

WITH PTFE (TEFLON)

PER MIL-A-8625

TYP III, CLASS 1)

SEE BOM

SECTION A-A

DETAIL B

DETAIL C

A A

B B

SIZE DWG NO REV

SHEET 2 OF 2

FINISH

CHECKED

TITLE

AN EMPLOYEE OWNED COMPANY

ORRVILLE, OH

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF THE

WILL-BURT COMPANY ANY REPRODUCTION

IN PART OR WHOLE WITHOUT THE WRITTEN

PERMISSION OF THE WILL-BURT COMPANY IS

PROHIBITED.

DRAWN

MATERIAL UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES.

APPROVALS DATE

PROPRIETARY AND CONFIDENTIAL

TOLERANCES ON DECIMALS ANGLES

0 = 0.030 1/2 00 = 0.010

000 = 0.005

FRACTIONAL 1/64"

1. ALL INSIDE EDGES TO HAVE

.005" TO .035" FILLETS.

2. ALL OUTSIDE EDGES TO HAVE

.005" TO .015" CHAMFER OR RADIUS.

THIRD ANGLE PROJECTION PN:125 ON ALL MACHINED SURFACES

PNEU MAST 5.5-25 HDNL

HRDC W/T CE CUSTOM

710302542 00B8/25/2015

710302542

C:\_Vault-WF\Inventor\710000000\710302542.idw

WILL-BURT

msmith

A

A

B

C x48 x48

(3 3)

SEE SHEET

(9.0)

6 6 6

SEE SHEET

18 17

18 17

11 10