C04.0 N4523A24R1050 APL-62 Attachment J-6 References and Drawings - Additional Drawings.pdf

For the best experience, open this PDF portfolio in

Acrobat X or Adobe Reader X, or later.

Get Adobe Reader Now!

http://www.adobe.com/go/reader

AutoCAD SHX Text

DOOR_NO.

DECK

REMARKS

CLEAR_OPNG1

LOCATION

FXD_LT

RATING

KEY PLAN 4-D 03 LEVEL SCALE: NONE

FWD

C

L

MAIN DECK

DETAIL 4-B BARGE HULL LETTERS TYP PORT, STBD & AFT SCALE: "=1'-0" 332"=1'-0"

NOTE: FOR ADDITIONAL INFORMATION

SEE REF 2.

REVISION STATUS

OF SHEETS

B

DESTRUCTION NOTICE: THIS DOCUMENT MAY BE DESTROYED BY ANY MEANS THAT WILL PREVENT DISCLOSURE OF CONTENTS OR RECONSTRUCTION OF THE DOCUMENT

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C. SEC. 2751 ET SEQ.) OR THE EXPORT ADMINISTRATION ACT OF 1979, AS AMENDED, TITLE 50, U.S.C. APP. 2401, ET SEQ. VIOLATIONS OF THESE LAWS ARE SUBJECT TO SEVERE CRIMINAL PENALTIES. DISSEMINATE PER THE PROVISIONS OF OPNAVINST 5510.161.

DISTRIBUTION STATEMENT D: DISTRIBUTION AUTHORIZED TO DOD AND DOD CONTRACTORS ONLY; TO PROTECT CRITICAL TECHNOLOGY; FOR DATE USE THE APPROVED DATE OF THIS DOCUMENT.OTHER U.S. REQUESTS SHALL BE REFERRED TO THE APPROPRIATE HULL PLANNING YARD.

PSNS & IMF

J. HOOVER /S/

07/02/15

D. SOMMER /S/

C. BLANKENBAKER /S/

F

APVD

DATE

ENGR

E

D

DESCRIPTION

REVISIONS

ZONE

REV

A

WT GRP

CODE/DEPT:

SIZE

FSCM No.

SCALE:

APPROVED

ENGINEER

CHECKED

PREPARED

WASHINGTON NAVY YARD, D.C. 20376-1010

NAVAL SEA SYSTEMS COMMAND

DEPARTMENT OF THE NAVY

NAVSEA DRAWING No.

SDI INFORMATION

SHEET 1 OF 3

280.51

AS SHOWN

53711

EXT PAINT SCHED

8520416

WI-52

APL62

EXTERIOR

PAINT SCHEDULE

THIS DRAWING MODIFIES

REFERENCES 1, 3 & 4 FOR

APPLICABLE CRAFTS UPON

ACCOMPLISHMENT OF WI-52.

VAL

OR

O

S

P

BY

TCG

REF CL

VCG

MIDSHIP

LCG REF

XI

R

I

XR

(LBS)

WT

REF BL

NUMBER

ALTERATION

WT GR

WEIGHT CONTROL DATA

SHIP APPLICABILITY

DT

SHIPCK BY

SHIP

02/14

01/15

APPROVED BY NAVSEA

ACCEPTED FOR NAVSEA

NOT REQUIRED

CAGE 82522

BREMERTON, WA 98314-5001

1400 FARRAGUT AVE

INTERMEDIATE MAINTENANCE FACILITY

PUGET SOUND NAVAL SHIPYARD AND

DIMENSIONAL TOLERANCES

SYM

SYMBOLS & TOL IN ACCORDANCE WITH ASME Y14.5

GEOMETRIC (WHERE IND)

UNLESS OTHERWISE SPECIFIED

FILLETS & RADII TO BE

TOL ON ANGLES %%P %%D

DIM ARE IN INCHES

MACH / FAB

DIM.

%%P

DEC

FRAC

PARALLELISM

PERPENDICULAR

STRAIGHTNESS

CONCENTRICITY

FLATNESS

GEOMETRY

TOL

1/4

1/8

1/16

0 TO 12

12 TO 72

OVER 72

SYMBOLS & TOL IN ACCORDANCE WITH ASME Y14.5

CONTRACT No.

FSCM No.

CHECKED

ENGINEER

APPROVED

PREPARED

AUTHORITY:

DWG REVISED TO INCORPORATE LAR WI-52/ BGPUGT/

8628- WHICH CHANGES THE EXTERIOR PAINT COLOR

FROM HAZE GRAY TO WHITE.

SHT1

MOD: L/M ITEM 5 & 6 QUANTITIES.

SHT2

MOD: TABLE 14-F ITEMS 5-10.

J. SWIDECKI /S/

01/20/2015

DRAWING REVISED IN ITS ENTIRETY TO

ADJUST MATERIAL QUANTITIES PER LAR

SHT 1

WI-52/BGPUGT/8628A

7/9/15

D. SOMMER /S/

NO.

HULL

TITLE

IDENT

REFERENCES

PAINT SCHEDULE

631-7122144

TYPE

DISTINGUISHING FIGURES MISC VESSELS

S2804-921819

DECK COVERING SCHEDULE

634-7122102

DECK MODS FOR GYM & TRACK 03 LEVEL

606-8337059

HANDRAILS & LADDERS

612-7122140

ITEM

NO

REQD

QTY

VIEW NO.

APL/PN/

MATL REQD

MATERIAL SPEC

NO.

USED

LAST

PCS

REQD

PART NO.

NSN/MFR

UNIT

SOURCE

TOTAL

WEIGHT

LIST OF MATERIAL (QUANTITY FOR ONE SHIP)

GL

PAINT, ANTI-CORROSIVE

RED

MIL-PRF-24647

TYPE II

IAF

INTERNATIONAL PAINT INC

SEE GN 2.07

PAINT, ANTI-CORROSIVE

GRAY

PAINT, ABLATIVE

ANTI-FOULING-RED

18.5

14338

PAINT, ABLATIVE

ANTI-FOULING-BLACK

18.5

ENAMEL, SILICONE ALKYD COPOLYMER

DECK GRAY, COLOR #26008

MIL-PRF-24635

TY-III, GR-B

LOW SOLAR ABSORB

W/ANTI-STAIN

WHITE COLOR #27875

TYPE-III, GR-B

GRADE-A

LIGHT GRAY, COLOR #26373

TYPE-II, GR-B

LOW SOLAR ABSORPTION

10850

SF

NONSKID, PEEL AND STICK

SYSTEM W/SEALANT

MIL-PRF-24667

TYPE-XI

COMP-PS

0.01

108.5

SERVICE LIFE OF

12 MONTHS

COATING SYSTEM, EPOXY

MIL-PRF-23236

TY V OR VI

CL 5 OR 7

OCEAN GRAY,COLOR #26173

TY-II,CL-2,GR-B

10.7

10.7

LOW SOLAR ABSORPTION

DESCRIBED IN THE LIST OF REMOVED MATERIAL.

R-2

REMOVAL ITEM NUMBERS DENOTED BY HEXAGONAL SYMBOLS ON THIS DRAWING ARE

WITH MATERIAL IDENTICAL TO THE DAMAGED MATERIAL.

R-1

ALL DAMAGE CAUSED BY REMOVAL OF EXISTING MATERIAL SHALL BE REPAIRED

%%UREMOVAL NOTES

%%UGENERAL NOTES

1.00

ADMINISTRATIVE NOTES

1.01

THIS DRAWING WAS DEVELOPED FOR ACCOMPLISHMENT OF WORK ITEM 52 BASED ON

A CRAFTCHECK OF THE APL62. AN APPLICABILITY CRAFTCHECK IS REQUIRED

PRIOR TO ITS USE ON OTHER CRAFT.

1.02

THIS DRAWING IS BASED UPON THE REQUIREMENTS OF AMERICAN BUREAU OF

SHIPPING RULES FOR BUILDING AND CLASSING STEEL BARGES - 2015, WHOSE

PROVISIONS SHALL PREVAIL IN AREAS WHERE THIS DRAWING IS SILENT.

1.03

EXCEPT WHERE OTHERWISE NOTED OR APPROVED BY NAVSEA, THE EFFECTIVE DATE

OF FEDERAL OR MILITARY SPECIFICATIONS, PUBLICATIONS AND STANDARD/TYPE

DRAWINGS AND REVISIONS AND CHANGES THERETO SHALL BE THE EFFECTIVE DATE

OF ABS RULES. LATER SPECIFICATION REVISIONS MAY BE USED PROVIDED THAT

THEY MEET THE INTENT AND INTERFACE REQUIREMENTS OF THE SPECIFICATION

INVOKED FOR THE SPECIFIC AVAILABILITY.

1.04

THE PURPOSE OF THIS DRAWING IS TO PROVIDE EXTERIOR PAINTING

REQUIREMENTS IN SUPPORT OF WORK ITEM 52.

1.05

AN ASTERISK (*) APPEARING BESIDE A REFERENCE INDICATES THE REFERENCE

IS REQUIRED TO SUPPORT MATERIAL ORDERING, DEVELOPMENT OF ESTIMATES,

AND ACCOMPLISHMENT OF INDUSTRIAL WORK INCLUDING TESTING.

2.00

PRODUCTION NOTES

2.01

STRUCTURAL LEGEND

EXISTING NEW REMOVAL ////////////

2.02

THE NUMBER AND LETTER IN PARENTHESES ( ) BELOW THE VIEW TITLE

DENOTES THE VIEW FROM WHICH IT WAS TAKEN.

2.03

SYMBOLS AND ABBREVIATIONS ARE IN ACCORDANCE WITH MIL-STD-25 AND

ASME Y14.38-1999 EXCEPT AS FOLLOWS:

(E) = EXISTING PSNS = PUGET SOUND NAVAL SHIPYARD

(N) = NEW IAF = INSTALLATION ACTIVITY FURNISHED

(P) = PORT WI = WORK ITEM

2.04

PAINT AREAS AS SPECIFIED IN TABLE 14-F. REFER TO PAINTING NOTES ON

SHEET 2. PAINTING OF ALL CLIPS AND FOUNDATIONS ATTACHED TO SURFACES

IS COVERED BY THIS DRAWING.

2.05

UNLESS OTHERWISE SPECIFIED, PAINT AREAS AS DIRECTED ON SHEET 2

OF THIS DRAWING USING ITEMS IN THE LIST OF MATERIAL. PREPARATION AND

PAINTING SHALL BE ACCOMPLISHED PER NAVSEA STANDARD ITEM 009-32,

CLEANING AND PAINTING REQUIREMENTS.

2.06

ACTUAL "WET PAINT" WEIGHTS ARE SHOWN IN THE LIST OF MATERIALS.

2.07

A SUGGESTED SOURCE FOR L/M ITEMS IS:

INTERNATIONAL PAINT LCC

1541 S. 92ND PLACE, SUITE C

SEATTLE, WA 98108

2.08

THE EXTENT OF THE BOOTTOPPING AREA SHALL BE FROM THE MINIMUM LOAD

WATERLINE AT WHICH THE CRAFT IS EXPECTED TO OPERATE TO 12-INCHES ABOVE

THE FULL LOAD WATERLINE. FINAL LOCATION OF THE BOOTTOPPING AND

ASSOCIATED LIMITING DRAFT MARKS SHALL BE APPROVED BY THE NAVAL

SUPERVISING ACTIVITY PRIOR TO PAINT APPLICATION.

2.09

BOOTTOOPING LOCATION:

BOTTOM-4'-2" ABL (12" BELOW AVERAGE WATERLINE)

TOP-7'-2" ABL (18" ABOVE AVERAGE WATERLINE)

2.10

MATERIAL QUANITIES SHOWN IN THE L/M ARE BASED UPON DESIGN ESTIMATES.

EXACT QUANITIES REQUIRED TO COMPLETE INSTALLATION SHALL BE THE

RESPONSIBILITY OF THE INSTALLING ACTIVITY.

3.00

MATERIAL NOTES:

3.01

CRAFT'S STRUCTURE IS MILD STEEL.

SHT 2

SHT 3

UP

DN

1-88-1-Q

FAN

ROOM

MAIN

30"

FSCM NO.

NAVSEA DRAWING NO.

SHEET

HULL NUMBER

NONE

2ND COATING

L/M

3RD COATING

PO(SF)

NO

1ST COATING

TABLE 14-F

4TH COATING

5TH COATING

6TH COATING

EXTERIOR SURFACES

PAINTING # (SEE KEY BELOW)

BOOTTOPPING

BOOTTOPPING TO MN DK

SHIPS MARKING

94960

SEE GEN NOTE 2.04 & 2.08

12 YEAR SYSTEM

%%uEXTERIOR PAINT NOTES

ENVIRONMENTAL CONTROLS ARE PROVIDED.

MATERIAL. ENSURE THAT PROPER SAFETY AND

TO DETERMINE CONTENT PRIOR TO DISTURBING THIS

LEAD. A SAMPLE TESTING OF EXISTING PAINT IS REQUIRED

WORK ON THIS DRAWING MAY DISTURB PAINT CONTAINING

%%uWARNING - HAZARDOUS MATERIAL

SEE OPNAVINST 5100.23F, CHAPTER 21.

12 YEAR SYSTEM

2ND COAT STRIP COAT

SEE GEN NOTE 2.04

P-1.PREPARATION OF SURFACES TO BE PAINTED: A.CLEANLINESS (1) SURFACES TO BE PAINTED SHALL BE COMPLETELY FREE OF CORROSION PRODUCTS, MILL SCALE, DIRT, OIL GREASE MOISTURE, AND OTHER SURFACE CONTAMINATES AND SHALL MEET THE REQUIREMENTS OF NAVSEA STANDARD ITEM:009-32 AND PAINT MANUFACTURER'S INSTRUCTIONS. B.SURFACE PREPARATION (1) STRUCTURAL SURFACES AND FOUNDATIONS SHALL BE ABRASIVE STRUCTURAL SURFACES AND FOUNDATIONS SHALL BE ABRASIVE BLASTED TO SURFACE PREPARATION SPECIFICATION NACE 21/ SSPC SP-10 OR WATER-JETTING TO NACE/SSPC WJ-2/M (SEE GN 2.05) P-2. APPLICATION OF PAINT A. ALL SURFACES SHALL BE PRIMED AND PAINTED IN ACCORDANCE WITH STANDARD ITEM 009-32. MIXING APPLICATION SHALL BE IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS AND STANDARD ITEM 009-32. B. ALL EXTERIOR LADDER PLATFORMS AND LADDER TREADS SHALL HAVE PEEL AND STICK NON-SKID STRIPS APPLIED AS REQUIRED. C. EXTERIOR BULKHEADS SHALL BE PAINTED IN ACCORDANCE WITH TABLE 14-F, VERTICAL SURFACES. D. MOORING FITTINGS SHALL BE COATED IAW LINE NO. 5 OF TABLE 14-F.

P-2. APPLICATION OF PAINT (CONTINUED) E. STRUCTURAL DOORS (EXCEPT STAINLESS STEEL DOORS), HATCHES, HATCHWAYS, FOUNDATIONS, LIFERAILS, ETC., SHALL BE PAINTED PER LINES 5, 6, 7 & 9 OF TABLE 14-F. F. PAINTING THE HULL SHALL BE AS FOLLOWS: (1) SURFACES SHALL BE ABRASIVE BLASTED FROM KEEL TO UPPER LIMIT OF BOOTTOPPING AREA PER TABLE 1, LINE 1 OF NAVSEA STD ITEM 009-32. (2) ONE COAT OF AFTER BLAST PRIMER, ITEM 1, SHALL BE APPLIED AS SOON AS PRACTICABLE, BUT WITHIN 8 HOURS AFTER BLASTING HAS BEEN COMPLETED. IF RERUSTING (RUST BLOOM) OF THE STEEL OCCURS, IT SHALL BE REMOVED BY SWEEP BLASTING BEFORE ANY COATING IS APPLIED. AREAS OF DAMAGED PRIMER, ITEM 1 SHALL BE ABRASIVE BLASTED AND TOUCHED UP AS REQUIRED. ANY CORROSION PRODUCTS OR NON-ADHERING PAINT SHALL BE REMOVED AND THE SURFACE ABRASIVE BLASTED AND TOUCHED UP AS REQUIRED. IF MORE THAN 30 DAYS ELAPSES BETWEEN PRE-TREATMENT AND APPLICATION OF FULL ANTI-CORROSIVE COATINGS, SURFACES SHALL BE SWEEP BLASTED AND A TACK COAT OF ITEM 1 OR THE LAST COAT OF ANTI-CORROSIVE COATING (1-2 MILS WFT) SHALL BE APPLIED. (3) FOR REMAINING COATS OF PAINT SEE TABLE 14-F EXTERIOR SURFACES. (4) EXTERIOR STEEL SURFACES OF THE HULL ABOVE THE UPPER LIMIT OF BOOTTOPPING SHALL BE ABRASIVE BLASTED PER TABLE 2, LINE 1 OF NAVSEA STD ITEM 009-32. FOR REMAINING COATS OF PAINT SEE TABLE 14-F, EXTERIOR SURFACES. G. ALL EDGES OF PEEL & STICK NON-SKID SHALL HAVE A SEALING COMPOUND APPLIED FOR WATER TIGHTNESS. P-3. THE BARGE DESIGNATION INSCRIPTION SHALL BE ACCOMPLISHED THE BARGE DESIGNATION INSCRIPTION SHALL BE ACCOMPLISHED IN ACCORDANCE WITH DETAIL 10-A AND REF 2. P-4. ALL PAINTED AREAS SHALL BE INSPECTED TO ENSURE COATINGS ALL PAINTED AREAS SHALL BE INSPECTED TO ENSURE COATINGS HAVE BEEN PROPERLY APPLIED. P-5. THE FOLLOWING ITEMS SHALL NOT BE PAINTED: A. CATHODIC PROTECTION ANODES. B. HEAT EXCHANGER SURFACES. C. GASKET SEATS. D. LUBRICATING FITTINGS. E. NAMEPLATES, LABELS AND SIGNS. F. TREADS AND WORKING SURFACES. G. RUBBER AND OTHER ELASTOMERS. H. DISCHARGE NOZZLES. I. DECORATIVE AND FINISHED PARTS OF FURNISHINGS AND EQPT. J. ISOLATION MOUNTS. K. ALUMINUM LADDERS.

MAIN DECK, WEATHER, HORIZONTAL SURFACES (NON-SKID)

MAIN DECK WALKING SURFACE TO BE NON-SKID SEE PAINT NOTE P-2 SECTION B

MAIN DECK, 03 & 04 LEVEL, WEATHER, HORIZONTAL SURFACES (BEFORE NON-SKID)

03 LEVEL TO 04 LEVEL, WEATHER, VERTICAL SURFACES

02 LEVEL TO 03 LEVEL, WEATHER, VERTICAL SURFACES

01 LEVEL TO 02 LEVEL, WEATHER, VERTICAL SURFACES

MAIN DECK TO 01 LEVEL, WEATHER, FITTINGS & VERTICAL SURFACES

SEE GEN NOTE 2.04 SEE PAINT NOTE P-2 SECTION A 2ND COAT STRIP COAT

33600

DISTRIBUTION STATEMENT D: DISTRIBUTION AUTHORIZED TO DOD AND DOD : DISTRIBUTION AUTHORIZED TO DOD AND DOD CONTRACTORS ONLY; TO PROTECT CRITICAL TECHNOLOGY; FOR DATE USE THE APPROVED DATE OF THIS DOCUMENT. OTHER U.S. REQUESTS SHALL BE REFERRED TO THE APPROPRIATE HULL PLANNING YD.

1"

SHALL NOT BE USED FOR SCALING.)

DISTORTION IDENTIFICATION. BAR SCALE

(BAR SCALE SHOWN IS FOR REPRODUCTION

BAR SCALE

2"

DRAFT MARKING (TO BOOT-TOPPING)

DRAFT MARKING (ABOVE BOOT-TOPPING)

SEE DETAIL 10-A

SEE GN NOTE 2.09

KEEL TO TOP OF BOOTTOPPING

SEE PAINT NOTE P-2, SECTION B

SEE PLAN 21-D FOR LOCATIONS

03 LEVEL, WEATHER HORIZONTAL SURFACES (NON SKID WALKWAYS)

12 MONTH SERVICE LIFE

12 MONTH SERVICE LIFE

PLAN 13-A INSTALLATION - NEW WALKWAYS MAIN DECK SCALE: "=1'-0"116"=1'-0"

CPO MESS 1-8-0-L

OFFICER'S MESS 1-26-0-L

RECEIVING DOCK 1-41-1-L

CREW GALLEY 1-62-0-Q

CREW MESS 1-98-0-L

DECK HOUSE

CREW GALLEY 1-62-0-Q

PEEL & STICK STRIPS (60) PLACES (LOCATE AT ALL EXTERIOR DOORS)

SEE TABLE 14-F

SHIP

FSCM NO.

NAVSEA DRAWING NO.

SHEET

HULL NUMBER

NONE

LIST OF REMOVED MATERIAL (QUANTITY FOR ONE SHIP)

ITEM NO.

QTY RMVD

DISPOSITION

TYPE MATL

AS BUILT REF

TOTAL WEIGHT RMVD

SCRAP

FORWARD

RETAIN

R1

5400 SF

RUNNING TRACK, URETHANE

5400 SF

VAR

SEE RN R-1

RX

SEE NOTE R-2

DISTRIBUTION STATEMENT D: DISTRIBUTION AUTHORIZED TO DOD AND DOD : DISTRIBUTION AUTHORIZED TO DOD AND DOD CONTRACTORS ONLY; TO PROTECT CRITICAL TECHNOLOGY; FOR DATE USE THE APPROVED DATE OF THIS DOCUMENT. OTHER U.S. REQUESTS SHALL BE REFERRED TO THE APPROPRIATE HULL PLANNING YD.

SHALL NOT BE USED FOR SCALING.)

DISTORTION IDENTIFICATION. BAR SCALE

(BAR SCALE SHOWN IS FOR REPRODUCTION

BAR SCALE

RUNNING TRACK

PLAN 21-A REMOVAL - RUNNING TRACK 03 LEVEL SCALE: "=1'-0" 116"=1'-0" (4-C)

(E) DKHSE SIDE (TYP)

(E) 04 LEVEL DKHSE (TYP)

PLAN 21-D INSTALLATION - NEW WALKWAYS 03 LEVEL SCALE: "=1'-0" 116"=1'-0" (4-C)

(E) 04 LVL DKHSE (TYP)

(E) DKHSE SIDE (TYP)

SEE TABLE 14-F

PEEL & STICK STRIPS (21) PLACES (LOCATE AT ALL EXTERIOR DOORS)