mSDS-f76.pdf

Material Safety Data Sheet

1 . Identification of the material and supplier

Marine Naval Fuel F76Product name

YSTMOHistoric SDS no.

0000003656SDS no.

Product use Diesel fuel for marine applications, conforming to DEF (AUST) 5213A.

BP Australia Pty Ltd (ABN 53 004 085 616) 717 Bourke Street Docklands VIC 3008 Australia Tel: +61 (03) 9268 4111 Fax: +61 (03) 9268 3321

Supplier

1800 638 556EMERGENCY TELEPHONE

NUMBER

Product code 0000003656

Hazards identification2 .

HAZARDOUS SUBSTANCE. NON-DANGEROUS GOODS.Statement of hazardous/dangerous nature

R40- Limited evidence of a carcinogenic effect.

R65- Harmful: may cause lung damage if swallowed.

Risk phrases

S2- Keep out of the reach of children.

S24- Avoid contact with skin.

S29- Do not empty into drains.

S36/37- Wear suitable protective clothing and gloves.

S43- In case of fire, use water, dry chemical powder or carbon dioxide. Do not use water jet.

S61- Avoid release to the environment. Refer to special instructions/safety data sheet.

S62- If swallowed, do not induce vomiting: seek medical advice immediately and show this container or label.

Safety phrases

Composition/information on ingredients3 .

May also contain small quantities of proprietary performance additives. Contains small amounts of diethyleneglycol monomethyl ether (DEGME, 2-(2-methoxyethoxy)ethanol ) as a fuel icing inhibitor.

Fuels, diesel 68334-30-5 100 Contains small quantities of polycyclic aromatic hydrocarbons (PAHs).

Other ingredients, determined not to be hazardous according to Safe Work Australia criteria, and not dangerous according to the ADG Code, make up the product concentration to 100%.

Ingredient name CAS no. %

Skin contact

In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Eyelids should be held away from the eyeball to ensure thorough rinsing. Check for and remove any contact lenses.

Get medical attention if irritation occurs.

In case of contact, immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash clothing before reuse. Clean shoes thoroughly before reuse.

Get medical attention if irritation develops.

4 .

If inhaled, remove to fresh air. Get medical attention.Inhalation

Eye contact

First-aid measures

Ingestion Do not induce vomiting. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Aspiration hazard if swallowed. Can enter lungs and cause damage. Get medical attention.

Advice to doctor Treatment should in general be symptomatic and directed to relieving any effects.

Product can be aspirated on swallowing or following regurgitation of stomach contents, and can cause severe and potentially fatal chemical pneumonitis, which will require urgent treatment. Because of the risk of aspiration, induction of vomiting and gastric lavage should be avoided. Gastric lavage should be undertaken only after endotracheal intubation. Monitor for cardiac dysrhythmias.

Note: High Pressure Applications Injections through the skin resulting from contact with the product at high pressure constitute a major medical emergency. Injuries may not appear serious at first but within a few hours tissue becomes swollen, discoloured and extremely painful with extensive subcutaneous necrosis.

Surgical exploration should be undertaken without delay. Thorough and extensive debridement of the wound and underlying tissue is necessary to minimise tissue loss and prevent or limit permanent

Date of issue 27 October 2011

Page: 1/5Marine Naval Fuel F76Product name Product code

Version 2 Format LanguageAustralia

0000003656

ENGLISH

(ENGLISH)(Australia) damage. Note that high pressure may force the product considerable distances along tissue planes.

Fire-fighting measures5 .

Do not fight fire when it reaches the material. Withdraw from fire and let it burn. Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. First move people out of line-of-sight of the scene and away from windows.

Special fire-fighting procedures

Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode.

Protection of fire-fighters

Unusual fire/explosion hazards

Combustible liquid and vapour. Vapour may cause flash fire. Vapours may accumulate in low or confined areas or travel a considerable distance to a source of ignition and flash back. Runoff to sewer may create fire or explosion hazard.

Hazardous decomposition products

Decomposition products may include the following materials:

carbon dioxide carbon monoxide other hazardous substances.

Extinguishing media

Suitable In case of fire, use water fog, foam, dry chemical or carbon dioxide extinguisher or spray.

Do not use water jet.Not suitable

6 . Accidental release measures

Environmental precautions

Personal precautions

Stop leak if without risk. Eliminate all ignition sources. Move containers from spill area. Approach the release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see section 13). Use spark-proof tools and explosion-proof equipment. Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilt product. Note: see section 1 for emergency contact information and section 13 for waste disposal.

No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilt material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Avoid breathing vapour or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment (see Section 8).

Avoid dispersal of spilt material and runoff and contact with soil, waterways, drains and sewers.

Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to the environment if released in large quantities.

Large spill

Stop leak if without risk. Eliminate all ignition sources. Move containers from spill area. Absorb with an inert material and place in an appropriate waste disposal container. Use spark-proof tools and explosion-proof equipment. Dispose of via a licensed waste disposal contractor.

Small spill

Handling

Handling and storage

Storage

7 .

Aspiration hazard if swallowed. Can enter lungs and cause damage. Do not ingest. If ingested, do not induce vomiting. Never siphon by mouth. Avoid breathing vapours, spray or mists. Use only with adequate ventilation. Keep away from heat, sparks and flame. To avoid fire or explosion, dissipate static electricity during transfer by earthing and bonding containers and equipment before transferring material. Use explosion-proof electrical (ventilating, lighting and material handling) equipment. Avoid contact of spilt material and runoff with soil and surface waterways. Wash thoroughly after handling.

When using do not eat, drink or smoke.

Keep container tightly closed. Keep container in a cool, well-ventilated area. Store and use only in equipment/containers designed for use with this product.

Empty packages may contain some remaining product. Hazard warning labels are a guide to the safe handling of empty packaging and should not be removed.

Do not enter storage tanks without breathing apparatus unless the tank has been well ventilated and the tank atmosphere has been shown to contain hydrocarbon vapour concentrations of less than 1% of the lower flammability limit and an oxygen concentration of at least 20% volume.

Always have sufficient people standing by outside the tank with appropriate breathing apparatus and equipment to effect a quick rescue.

This product must be handled in compliance with Australian Standard: The storage and handling of flammable and combustible liquids [Standard 1940-2004 as amended and adapted].

Light hydrocarbon vapours can build up in the headspace of tanks. These can cause flammability/explosion hazards even at temperatures below the normal flash point (note: flash point must not be regarded as a reliable indicator of the potential flammability of vapour in tank headspaces). Tank headspaces should always be regarded as potentially flammable and care should be taken to avoid static electrical discharge and all ignition sources during filling, ullaging and sampling from storage tanks.

Will present a flammability hazard if heated above flash point but bulk liquids at normal storage temperatures will present virtually no fire hazard. If fuel contacts hot surfaces, or leaks from high pressure fuel pipes, the vapour and/or mists generated will create a flammability or explosion hazard.

Product contaminated rags, paper or material used to absorb spillages, represent a fire hazard, and should not be allowed to accumulate. Dispose of safely immediately after use.

Empty containers represent a fire hazard as they may contain flammable product residues and vapour.

Never weld, solder or braze empty containers.

Additional information- Storage

Combustibility Classification Combustible liquid Class C1 (AS 1940).

Date of issue 27 October 2011

Page: 2/5Marine Naval Fuel F76Product name Product code

Version 2 Format LanguageAustralia

0000003656

To avoid fire, eliminate ignition sources.

8 . Exposure controls/personal protection

Ingredient name Occupational exposure limits

Fuels, diesel ACGIH TLV (United States). Absorbed through skin.

TWA: 100 mg/m³, (measured as total hydrocarbons) 8 hour(s). Issued/Revised:

1/2007 Form: Total hydrocarbons

For information and guidance, the ACGIH values are included. For further information on these please consult your supplier.

Provide exhaust ventilation or other engineering controls to keep the airborne concentrations of vapours below their respective occupational exposure limits. In accordance with good industrial hygiene and safety work practices, airborne exposures should be controlled to the lowest extent practicable.

Occupational exposure controls

Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period. Ensure that eyewash stations and safety showers are close to the workstation location.

Hygiene measures

Biological Limit Values No biological limit allocated.

Personal protective equipment

Use only with adequate ventilation. Avoid breathing of vapours, mists or spray. Select and use respirators in accordance with AS/NZS 1715/1716. When mists or vapours exceed the exposure standards then the use of the following is recommended: Approved respirator with organic vapour and dust/mist filters. Filter capacity and respirator type depends on exposure level.

Respiratory protection

Avoid contact with skin and clothing. Wear clothing and footwear that cannot be penetrated by chemicals or oil.

Skin and body

Wear protective gloves if prolonged or repeated contact is likely. Recommended: Nitrile gloves.

The correct choice of protective gloves depends upon the chemicals being handled, the conditions of work and use, and the condition of the gloves (even the best chemically resistant glove will break down after repeated chemical exposures). Most gloves provide only a short time of protection before they must be discarded and replaced. Because specific work environments and material handling practices vary, safety procedures should be developed for each intended application. Gloves should therefore be chosen in consultation with the supplier/manufacturer and with a full assessment of the working conditions.

Hand protection

Chemical splash goggles.Eye protection

Exposure controls

Physical and chemical properties9 .

Auto-ignition temperature 240°C (464°F)

Lower: 0.7% Upper: 5%

Explosion limits

Combustible liquid and vapour. Vapour may cause flash fire. Vapours may accumulate in low or confined areas or travel a considerable distance to a source of ignition and flash back. Runoff to sewer may create fire or explosion hazard.

Explosive properties

Flash point >61.5 °C (Closed cup) Pensky-Martens.

Colour Clear, Bright

Physical state Liquid.

Odour Mild

180 to 360°C (356 to 680°F)Boiling point / range

Not available.Melting point / range

810 to 850 kg/m3 (0.81 to 0.85 g/cm3) at 15°CDensity

Vapour density Not available.

<0.1 kPa (<0.75 mm Hg) at 20°CVapour pressure

Solubility Insoluble pH Not available.

Relative density/Specific gravity

0.84

Viscosity Kinematic: <7 mm2/s (<7 cSt) at 40°C

Stability and reactivity10 .

The product is stable.Stability

Conditions to avoid Avoid all possible sources of ignition (spark or flame). Avoid excessive heat.

Incompatibility with various substances/Hazardous Reactions

Reactive or incompatible with the following materials: oxidising materials.

Decomposition products may include the following materials:

carbon dioxide carbon monoxide other hazardous substances.

Hazardous decomposition products

Date of issue 27 October 2011

Page: 3/5Marine Naval Fuel F76Product name Product code

Version 2 Format LanguageAustralia

0000003656

Toxicological information11 .

Eyes Vapour, mist or fume may cause eye irritation. Exposure to vapour, mist or fume may cause stinging, redness and watering of the eyes.

Causes skin irritation. Prolonged or repeated contact can defat the skin and lead to irritation and/or dermatitis.

Skin

Inhalation Harmful if inhaled. May cause irritation of respiratory tract, coughing, shortness of breath.

Aspiration of this product into the lungs may cause chemical pneumonia and can be fatal. Aspiration into the lungs can occur while vomiting after ingestion of this product. Do not siphon by mouth.

Irritating to mouth, throat and stomach.

Ingestion

Mutagenic effects No known significant effects or critical hazards.

POSSIBLE CANCER HAZARD - CONTAINS MATERIAL WHICH MAY CAUSE CANCER, BASED ON

ANIMAL DATA. -- Carcinogenic Category 3 Risk of cancer depends on duration and level of exposure.

Carcinogenic effects

Other information May cause damage to organs through prolonged or repeated exposure. Vapour, mists or fumes may contain polycyclic aromatic hydrocarbons some of which are known to produce skin cancer.

Diesel exhaust particulates have been classified by the National Toxicological Program (NTP) to be a reasonably anticipated human carcinogen. Exposure should be minimized to reduce potential risk.

Effects and symptoms

Chronic toxicity

Ecological information

Ecotoxicity

12 .

Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.

Biodegradability

Persistence/degradability This product is inherently biodegradable.

Mobility

Bioaccumulative potential

Spillages may penetrate the soil causing ground water contamination. This material may accumulate in sediments.

This product is not expected to bioaccumulate through food chains in the environment.

Other ecological information Spills may form a film on water surfaces causing physical damage to organisms. Oxygen transfer could also be impaired.

Disposal considerations13 .

The generation of waste should be avoided or minimised wherever possible. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe way. Significant quantities of waste product residues should not be disposed of via the foul sewer but processed in a suitable effluent treatment plant. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Avoid dispersal of spilt material and runoff and contact with soil, waterways, drains and sewers.

Disposal considerations / Waste information

Empty packages may contain some remaining product. Hazard warning labels are a guide to the safe handling of empty packaging and should not be removed.

Special Precautions for Landfill or Incineration

14 . Transport information

International transport regulations

ADG

Classification

Regulatory information

UN number Proper shipping name Class PG* Additional information

Not regulated.

- - - Remarks Combustible liquid Class

C1 (AS 1940).

Label

IMDG

Classification

UN 1202 DIESEL FUEL. Marine pollutant (Fuels, diesel)

3 III Emergency schedules (EmS) F-E,S-E

-III3DIESEL FUELUN 1202IATA/ICAO

Classification

PG* : Packing group

Date of issue 27 October 2011

Page: 4/5Marine Naval Fuel F76Product name Product code

Version 2 Format LanguageAustralia

0000003656

Regulatory information

UN number Proper shipping name Class PG* Additional informationLabel

No known special precautions required. See Section: "Handling and storage" for additional information.

Special precautions for user

Regulatory information15 .

Standard for the Uniform Scheduling of Medicines and Poisons

Schedule No Listed Substance

Other regulations

All components are listed or exempted.

All components are listed or exempted.

All components are listed or exempted.

All components are listed or exempted.

All components are listed or exempted.

All components are listed or exempted.

All components are listed or exempted.

Ingredient name

Control of Scheduled Carcinogenic Substances

Australia inventory (AICS)

Canada inventory

China inventory (IECSC)

Japan inventory (ENCS)

Korea inventory (KECI)

Philippines inventory

(PICCS)

United States inventory (TSCA 8b)

REACH Status For the REACH status of this product please consult your company contact, as identified in Section 1.

Not scheduled

Consumer products - This product is exempt per Appendix A of the SUSMP.

Industrial Products - Labelling requirements for SUSMP do not apply to a poison that is packed and sold solely for industrial, laboratory or manufacturing use. However, this product is labelled in accordance with NOSHC National Code of Practice for labelling of workplace substances.

Other information16 .

AMP = Acceptable Maximum Peak ACGIH = American Conference of Governmental Industrial Hygienists, an agency that promulgates exposure standards.

ADG = Australian Code for the Transport of Dangerous Goods by Road and Rail ADG Code = Australian Code for the Transport of Dangerous Goods by Road and Rail CAS Number = Chemical Abstracts Service Registry Number HAZCHEM Code = Emergency action code of numbers and letters which gives information to emergency services. Its use is required by the ADG Code for Dangerous Goods in bulk.

ICAO = International Civil Aviation Organization.

IATA = International Air Transport Association, the organization promulgating rules governing shipment of goods by air.

IMDG = International Maritime Organization Rules, rules governing shipment of goods by water.

IP 346 = A chemical screening assay for dermal toxicity. The European Commission has recommended that Method IP 346 be used as the basis for labelling certain lubricant oil base stocks for carcinogenicity. The EU Commission has stipulated that the classification as a carcinogen need not apply if it can be shown that the substance contains less than 3% DMSO extract as measured by IP 346. (See Note L, European Commission Directive 67/548/EEC as amended and adapted.) DMSO is a solvent.

NOHSC = National Occupational Health & Safety Commission, Australia TWA = Time weighted average STEL = Short term exposure limit UN Number = United Nations Number, a four digit number assigned by the United Nations Committee of Experts on the Transport of Dangerous Goods.

Key to abbreviations

History

Date of issue

Date of previous issue

Prepared by Product Stewardship

Notice to reader

All reasonably practicable steps have been taken to ensure this data sheet and the health, safety and environmental information contained in it is accurate as of the date specified below. No warranty or representation, express or implied is made as to the accuracy or completeness of the data and information in this data sheet.

The data and advice given apply when the product is sold for the stated application or applications. You should not use the product other than for the stated application or applications without seeking advice from us.

It is the user’s obligation to evaluate and use this product safely and to comply with all applicable laws and regulations. The BP Group shall not be responsible for any damage or injury resulting from use, other than the stated product use of the material, from any failure to adhere to recommendations, or from any hazards inherent in the nature of the material. Purchasers of the product for supply to a third party for use at work, have a duty to take all necessary steps to ensure that any person handling or using the product is provided with the information in this sheet. Employers have a duty to tell employees and others who may be affected of any hazards described in this sheet and of any precautions that should be taken.

27/10/2011.

10/03/2011.

Date of issue 27 October 2011

Page: 5/5Marine Naval Fuel F76Product name Product code

Version 2 Format LanguageAustralia

0000003656