Att 010 21R1909 QAs_Amendment 0003.pdf

We were provided with the lengths for the back of wrist webbing (3.4.6) but were not provided lengths for the other trims (3.4.5; 3.4.8; 3.4.10). I imagine this information was included in a pattern project document but as our software could not read those files, I was hoping you may be able to provide that information as well.

3.4.5 ‐ Elastic ‐ there are elastic placement notches provided on the nylon back of hand pattern piece at the wrist (see attached). However, cut lengths are not provided. Due to variations in equipment, stitching, etc, offerors should determine the cut length needed based off of the finished wrist width provided in Table VII ‐ finished dimensions ‐ of MIL‐TFM‐ 003.

3.4.8 ‐ Adjustable lanyard ‐ no cut length provided. Figure 1 of MIL‐TFM‐003 can be used to approximate the length ‐ no specific requirement.

3.4.10 ‐ Elasticized drawcord ‐ no cut length provided. The elasticized draw cord runs through the hem of the mitten cuff so offerors should determine an appropriate length based off of the width of the pattern. As stated in 3.4.10: The elastic shall be sufficient for continuous expansion and relaxation, and when relaxed. The elastic shall allow for comfort on the arm, and provide desired closure over various clothing layers.

We are still unable to procure key specified materials like the shell fabric and the wool liner fabrics.

The Government confirmed with known supplier(s) that materials are now available. 3

Par 3.4.15/Table II addresses 3 different types of seam tape. It covers the widths of the tapes and whether the tapes are 2 or 3 layer tapes. However, 2L and 3L tapes come in many varieties. Do you have any more details on the tapes you are requiring to be used? Did you really mean to require 3 different tapes?

Specification paragraph 3.4.15 has been updated in its entirety to read: "The mitten shell shall be seam taped, providing complete water proofing. All seams and stitch lines shall be seam sealed on the inside seams; seam tape shall be centered over the stitch lines.

Attachment point tabs shall be created by folding the seam seal tape on itself. The cut length shall be 3 inches to form a ¾ inch self‐faced tab with a ¾ inch length of single layer seam seal tape on each side to affix to the specified locations. The mitten shall have a minimum of four attachment point tabs; located at the tip of thumb, the tip of the trigger finger, the top of the mitten section, and at the pinky side of the mitten section."

Additionally, Table II, Seam tape, has been deleted in its entirety. Please see updated specification provided as part of solicitation Amendment 0003.

Material: 70 Denier Nylon Taslan, Blockade Assault 3 Layer, Manufacturer Brookwood

a. As per the solicitation MIL‐TFM‐002 (6.5.1). The material cannot be tested in accordance with the patented and proprietary WL Gore whole glove leak test.

b. WL Gore communicated the Whole Glove Leak Tester, US Patent 4,776,209, can only be purchased and used when Gore material is part of the glove composition.

c. Based on information obtained, either the test or the material needs to be adjusted.

The Government will waive this test for the PDM’s. PPV’s will be tested at Natick. Please note that Gore’s Whole Glove Leak tester is not required for testing. The apparatus is listed as a known source in specification section 6.5, sources of supply, but is not a requirement.

Material: Cyberian Cord Lock, PN 350‐8200‐5614, Manufacturer ITW Nexus

a. Based on our knowledge, the specified part number is Not Berry Compliant.

b. We do not have a known USA supplier for this material.

The cord lock listed in specification section 6.5.8 as a source of supply is a suggested source, not a requirement. Any Berry compliant cord lock meeting the requirement of 3.4.11 may be used.

Material: Style #5639

a. Part number referenced does not match any known supplier.

Style number is listed in specification section 6.5.5 as a source of supply, which is a suggested source, it is not a requirement. Suppliers may use any Berry compliant adjustable lanyard conforming to specification section 3.4.8. 3

Material: Primasoft Siver Insulation, Manufacturer PrrimaLoft.

a. We requested sample material and have been told there is a lead time of 4‐6 weeks by the manufacturer.

Primaloft is not the only supplier of the insulation required in 3.4.4. Suggested sources of supply lists two other available sources. Additional sources that meet specification section

3.4.4 may also be used. If the required insulation is unavailable, an alternate insulation may be used for the PDM’s only and should be noted in the offeror’s proposal.

Material: High Release Lock, Style #94570 HRL, Manufacturer American Cord & Webbing

a. We requested sample material and have been told there is a lead time of 8 weeks by the manufacturer.

b. Additionally please be aware, the manufacturer indicated that they have 12K units on hand, however they will not release any sample material unless a minimum order is placed of 20K units

Style #94579 is listed in specification section 6.5.4 as a source of supply as a suggested source, it is not a requirement. Additional buckles that meet specification section 3.4.7 may also be used