Attachment_1_-_IFF_Antenna_P._Spec.docx

UNCLASSIFIED

(U) PERFORMANCE SPECIFICATION

FOR THE

AN/TPS-59A(V)3 IFF ANTENNA REPLACEMENT

PREPARED FOR:

MARINE CORPS SYSTEMS COMMAND

QUANTICO, VIRGINIA 22134

3 May 2017

DISTRIBUTION STATEMENT A. Authorized for Public Release. Distribution is Unlimited

(U) REVISION HISTORY

(U) When referencing the location of material in this document, the reader is advised to use paragraph numbers rather than page numbers because with printing and/or revision the pagination may change.

(U) TABLE OF CONTENTS

Page

UNCLASSIFIED

UNCLASSIFIED

(U) SCOPE

(U) Identification

(U) This Specification defines the AN/TPS-59A(V)3 Radar System’s Secondary Surveillance Radar, Identification Friend or Foe (IFF) Antenna Performance requirements. The antenna is a component of the IFF subsystem and a subgroup of the Antenna Transmitter Group (ATG).

(U) The existing Flat Plate IFF Antenna (808400/000) is a Line Replaceable Unit that is no longer manufactured and is obsolete. The Radar System has an extended service life through 2035 and requires a replacement IFF Antenna for continued support through the service life of the radar.

(U) System Overview

(U) The AN/TPS-59A(V)3 is a transportable, long-range, solid state, 3-Dimensional L-band radar. The AN/TPS-59A(V)3 is comprised of an ATG, Signal Data Processing Group, Power Distribution Unit, Equipment Transport Shelter, and System Cables.

(U) The AN/TPS-59A(V)3 Radar System provides electronically scanned in elevation and continuous mechanical rotation in azimuth, automatic radar and IFF target detection and processing. The radar provides a maximum Air-Breathing Target (ABT) surveillance volume of 4 to 300 nautical miles in range, 0.5 to 19.0 degrees in elevation, 100,000 feet in altitude, and 360 degrees in azimuth.

(U) The system performs detection of ABTs by the primary radar and detection of IFF targets by the IFF interrogator. ABT and IFF targets are correlated into a single report if they are from the same target. ABT, IFF, and correlated ABT and IFF targets are sent to the Command and Control (C2) node, as well as providing this data to the Cooperative Engagement Processor external interface in its role as a surveillance radar.

(U) The current MARK XII IFF secondary surveillance system (AN/UPX-37, AN/UPA-61, KIT-1C, KIR-1C, KIV-77/78, etc.) is capable of interrogating Targets of Opportunity using Modes 1, 2, 3/A, C and 4. The AN/UPX-37 will be replaced by the AN/UPX-41(C) Digital Interrogator, the CP-2819 Processor and interconnecting cables. The radar is being upgraded to the MARK XIIA IFF secondary surveillance system capability for Mode 5 (Levels 1 & 2) and Mode S (Levels 1 & 2), in addition to the existing interrogation modes.

(U) Document Overview

(U) The purpose of this Performance Specification is to specify the performance requirements for the IFF Antenna Replacement. The requirements in this document apply to a new IFF Antenna hardware procurement. The content and format of this document complies with MIL-STD-961E.

(U) REFERENCED DOCUMENTS

(U) The following documents in their latest version form a part of this specification to the extent specified herein.

(U) Standards, Handbooks, and Guidance

(U) SD-15

(U) Guide for Performance Specifications

(U) MIL-STD-454N

(U) Standard General Requirements for Electronic Equipment

(U) MIL-STD-810G

(U) Environmental Test Method and Engineering Guidelines

(U) MIL-STD-961E

(U) Defense and Program-Unique Specifications Format and Content

(U) MIL-STD-1472F

(U) Human Engineering Design Criteria for Military Systems, Equipment and Facilities

(U) Coatings and Paint

(U) FED-STD-595B

(U) Federal Standard: Colors Used in Government Procurement

(U) MIL-A-8625F

(U) Anodic Coatings, for Aluminum and Aluminum Alloys

(U) MIL-C-5541F

(U) Chemical Conversion Coatings on Aluminum and Aluminum Alloy

(U) MIL-C-53072C

(U) Chemical Agent Resistant Coating System Application Procedures and Quality Control Inspection

(U) MIL-HDBK-1250A N2

(U) Corrosion Prevention and Deterioration Control in Electronic Components and Assemblies

(U) MIL-STD-1516B

(U) Unified Code for Coatings and Finishes for DoD Material

(U) MIL-STD-889B

(U) Dissimilar Metals

(U) Electromagnetic Emissions

(U) MIL-STD-461G

(U) Electromagnetic Emissions and Susceptibility Requirements for the Control of Electromagnetic Interference

(U) Reliability and Maintainability

(U) MIL-HDBK-217F

(U) Reliability Prediction of Electronic Equipment

(U) MIL-HDBK-472 (notice 1)

(U) Maintainability Prediction

(U) MIL-HDBK-781A

(U) Reliability Test Methods, Plans, and Environments for Engineering Development, Qualification, and Production

(U) MIL-STD-470B

(U) Maintainability Program for Systems and Equipment

(U) REQUIREMENTS

(U) Capability Requirements

(U) The IFF Antenna shall provide three independent beams (threshold): (1) Interrogate/Monopulse SUM for transmit and receive, (2) Side Lobe Suppression (SLS or Control) for transmit and receive, (3) Monopulse Difference for receive (threshold).

(U) The Interrogate and SLS characteristics shall apply to the frequency range 1026.5 MHz to 1033.5 MHz (threshold).

(U) The SUM, SLS and Difference characteristics shall apply to the frequency range 1085 MHz to 1095 MHz (threshold).

(U) The radiation at the SUM port, SLS port and Difference port shall be linearly polarized with Vertical Polarization (threshold).

(U) The Cross Polarization at the SUM port shall be greater than 20 decibel (dB) (threshold) at the main beam.

(U) The peak antenna gain at the SUM input port shall be at least 22 Decibels Above Isotropic (dBi) (threshold) and 24 dBi (objective).

(U) The peak transmit power at antenna SUM port shall be 10 kW (threshold).

(U) The average transmit power at antenna SUM port shall be 100 W (threshold).

(U) The peak input power at antenna SLS port shall be 10 kW (threshold).

(U) The average input power at antenna SLS port shall be 100 W (threshold).

(U) The SUM pattern’s horizontal 3-dB beam width shall be 4.5 ± 0.5 degrees (threshold) and 3.5 degrees nominal (objective).

(U) The SUM pattern’s horizontal side-lobe level, below the peak main beam, shall be greater than 25 dB (threshold).

1.1.1 (U) The SUM pattern’s vertical 3-dB beam width shall be 25.5 ± 3.0 degrees (threshold).

(U) The SUM pattern’s vertical side-lobe level, below the peak main beam, shall be greater than 18.0 dB (threshold).

(U) The isolation between SUM and Difference ports shall be greater than 28 dB (threshold).

(U) The maximum Voltage Standing Wave Ratio (VSWR) at the SUM port shall be 1.5:1 (threshold).

(U) The maximum VSWR ratio at the Difference port shall be 1.5:1 (threshold).

(U) The maximum VSWR ratio at the SLS port shall be 1.5:1 (threshold).

(U) The IFF Antenna shall support the IFF Modes 1, 2, 3, 4, 5 (Level 1 & 2 (threshold)), C, and S (Level 1 & 2 (threshold)) for a 360-degree’s rotation in the 6 Revolutions Per Minute (RPM) and 12 RPM rotation rates of the Primary Search Antenna.

(U) The IFF Antenna input/output connectors shall be female N-type, MIL-C-39012 (threshold) to accommodate three (3) channels output.

(U) The IFF Antenna dimensions shall not exceed 180” L x 35” H x 26” W (threshold).

(U) The IFF Antenna with mount shall not exceed 150 pounds (threshold) 115 pounds (objective).

(U) The IFF Antenna shall mount to the support frame of the AN/TPS-59A(V)3 Radar Antenna Array and accommodate the existing Auxiliary (AUX) antenna, lightning rods and aircraft warning lights (threshold).

(U) Computer Resource Requirements

(U) Computer Hardware Resource Utilization Requirements

(U) There are no associated Computer Hardware Requirements allocated to the IFF Antenna.

(U) Computer Software Requirements

(U) There are no associated Computer Software Requirements allocated to the IFF Antenna.

(U) Computer Communications Requirements

(U) There are no requirements imposed on the Computer Communication for the IFF Antenna.

(U) Electromagnetic Interference (EMI) / Electromagnetic Compatibility

(U) The IFF Antenna shall operate within the EMI emission susceptibility limits and self-compatibility limits in accordance the requirements associated with CE102, CS101, CS114, RE102 and RS103 of MIL-STD 461G (threshold).”

(U) The IFF antenna system provider shall protect from hazardous effects of electromagnetic radiation by specifying safe stand-off distances and by providing appropriate equipment labeling for Hazards of Electromagnetic Radiation to Ordnance, Hazard of Electromagnetic Radiation to Personnel, and Hazard of Electromagnetic Radiation to Fuel in accordance with DODI 6055.11 and Marine Corps Order 5104.2 and MIL-STD-464.

(U) Environment Requirements

(U) Exposed metal surfaces of the IFF antenna shall be painted in accordance with MIL-C-53039 or MIL-DTL-53039, with coating of FED-STD-595 Color #34094 (Green 383) (threshold).

(U) The IFF Antenna shall operate at altitudes between -300 feet and up to 10,000 feet above sea level (threshold).

(U) The IFF Antenna shall be capable of normal operation in wind speeds up to 50 knots (threshold).

(U) The IFF Antenna shall be capable of degraded operation of no more than 2 dB (due to antenna speed, tilt, and array surface variation) in wind speeds up to 75 knots and with up to 3.5 pounds per square foot of ice loading (threshold).

(U) The IFF Antenna shall be capable of operation in rainfall of at least 0.625 inch per hour (threshold).

(U) The IFF Antenna shall be capable of operation between -40 degrees and +50 degrees Celsius (threshold).

(U) The IFF Antenna shall be capable of storage between -40 degrees and +71 degrees Celsius (threshold).

(U) The IFF Antenna shall be capable of operation, transport, and storage in relative humidity up to 95%, where above +27 degrees Celsius; the relative humidity is based upon a dew point of +27 degrees Celsius (threshold).

(U) The IFF Antenna’s finishes and coatings on components shall allow them to endure exposure to a salt fog environment without suffering corrosion damage that would render the antenna inoperable in accordance with the salt fog test of MIL-STD-810G (threshold).

(U) The IFF Antenna shall meet IFF performance requirements when exposed to sand and dust particles in accordance with the sand and dust test of MIL-STD-810G (threshold).

1.1.2 (U) All connectors shall be supplied with captive hardware to prevent connector damage and the entrance of moisture and foreign material during storage (threshold).

(U) External Interface Requirements

(U) For the purposes of this specification, hardware and software elements that are connected to or used within the IFF subsystem but are not part of the contractor furnished equipment are considered external interfaces. The IFF Antenna’s external interfaces are:

· (U) IFF Interrogator (UPX-41(C))

· (U) CP-2819 Processor Controller, and

· (U) Radio Frequency (RF) cables

(U) Power Requirements

(U) The IFF Antenna is a sub-assembly within the AN/TPS-59A(V)3 radar system, and does not require external power for operation.

(U) Internal Interface Requirements

(U) There are no internal interface requirements allocated to the IFF antenna. All internal interfaces are left to the design of the antenna components.

(U) Quality Factors

(U) There are no requirements imposed on quality factors for the IFF antenna. All system quality factors are imposed through contractual channels and contractor selection.

(U) Reliability, Maintainability, Availability Requirements

(U) The IFF Antenna shall have a Mean Time Between Failure and Mean Time Between Critical Failure (MTBCF) of 125,000 hours (threshold).

(U) The IFF Antenna shall have a minimum of 15-year life span of being able to meet all IFF performance requirements without the need for scheduled depot maintenance (objective).

(U) Safety Requirements

(U) The IFF antenna assembly shall be designed to prevent personnel hazards involving electronic equipment safety design criteria in accordance with MIL-HDBK-454 and MIL-STD-882 (threshold).

(U) The IFF Antenna shall be designed for human engineering design criteria and principles in accordance with MIL-STD-1472D (threshold).

(U) Training-Related Requirements

(U) There are no Training-Related Requirements.

(U) Transport Requirements

(U) The IFF Antenna shall be capable of removal from the Primary Search Radar Antenna for transport (threshold).

(U) The IFF Antenna shall dis-assemble into multiple sections for transportation in an S-280 shelter floor loaded (threshold).

(U) The IFF Antenna shall have reusable ruggedized storage containers with carrying handles for two-person carry and anchor points for stowage and shipment (threshold).

(U) The floor loading storage space for all IFF Antenna containers shall not exceed 114” L x 19” W x 48” H (threshold).

(U) The IFF Antenna shall be transportable unpressurized at altitudes up to 45,000 feet (threshold).

(U) No single section or combination of sections of the IFF antenna, mounting hardware, and transport packaging that must be moved singularly or together during assembly, disassembly or transport shall weigh more than 85 pounds (threshold).

(U) Workmanship

(U) The standards for workmanship shall meet MIL-HDBK-454B (threshold).

(U) The Contractor shall comply with the Prohibited, Restricted and Hazardous Materials listed in NAS 411-1

(U) Qualification Provisions

(U) Demonstration, Test, Analysis, Inspection, and Special Qualification Methods may be used for verification of the requirements herein. The Verification Cross Reference Matrix (VCRM) for this specification contains a mapping between the requirements herein and the test method(s) used to verify each requirement. The VCRM will be maintained as part of the program-specific requirements trace tool and is separate from this specification.

(U) Verification Methods

(U) Methods utilized to accomplish verification include:

(U) Analysis (A)

(U) An element of verification that utilizes established technical or mathematical models or simulations, algorithms, charts, graphs, circuit diagrams, or other scientific principles and procedures to provide evidence that stated requirements were met.

(U) Demonstration (D)

(U) An element of verification that involves the actual operation of an item to provide evidence that the required functions were accomplished under specific scenarios. The item may be instrumented and performance monitored.

(U) Inspection (I)

(U) An element of verification that is generally nondestructive and typically includes the use of sight, hearing, smell, touch, and taste; simple physical manipulation; and mechanical and electrical gauging and measurement.

(U) Test (T)

(U) An element of verification in which scientific principles and procedures are applied to determine the properties or functional capabilities of items.

(U) Production Qualification Test (PQT)

(U) The PQT shall verify all of the technical specification requirements listed in this performance specification through a series of verification tests, demonstrations, inspections and analyses.

(U) PQT antenna system verifications are shown in the IFF Antenna Replacement Verification Cross Reference Matrix (VCRM). The VCRM is separate from this specification.

(U) VCRM

(U) The verification method(s) for the PQT shall be as outlined in Paragraph 4.1. When more than one verification method is specified in the VCRM (such as: A/D), the most rigorous method identifies the preferred verification method. The second position identifies the alternate method that may be used provided the Vendor can prove the requirement was met previously through a Government observed test or approved similarity analysis. The Government reserves the right to make the determination.

(U) The contractor may submit past test data or vendor data as a means of showing compliance to selected requirements of this specification, as long as the approach is documented in the Test Plan and approved by the Government.

(U) This test data shall be included as part of the Test Plan. The Test Plan approach shall include information such as the identification of the requirement the data is trying to satisfy, the Test Procedure utilized, the data/results obtained, documentation of the unit under test (i.e., confirm that the unit under test is the final design product intended for the antenna system) and an analysis of the results to verify compliance to the appropriate specification requirement. Acceptance of any such past data or analysis to satisfy specification requirements in lieu of testing shall be at the Government's discretion.

(U) Rejection by the Government of the test data, vendor data, the proposed approach or contractor data analysis shall require the contractor to perform a test to show compliance to the technical specification requirement that was not satisfactorily addressed by data/data analysis.

(U) Requirements Traceability

(U) The Requirements Traceability Matrix (RTM), contains a mapping of the engineering requirements in this specification to the applicable requirements in the lower-level specifications for the system. The RTM will be maintained as part of the program-specific requirements trace tool and is separate from this specification.

(U) NOTES

(U) Definitions

(U) Antenna Transmitter Group

(U) The Antenna Transmitter Group is responsible for transmission and reception of RF energy to cover the system’s surveillance and track volumes, and consists of the trailers (used for both transport and emplacement), the transmit / receive primary and secondary antennas, and supporting equipment.

(U) Electronics Group

(U) The Electronics Group consists of the hardware and software that processes data from the Antenna Transmitter Group, supports operator control of the system, and supports the system’s external interfaces, as well as the shelter enclosing this hardware.

(U) Corrective Maintenance

(U) Corrective maintenance is the action required to restore equipment which has failed.

(U) Mean Time Between Critical Failure

(U) The time between failures that result in the radar not meeting any critical performance requirement. MTBCF excludes those portions of the radar (e.g., service lift) that are not required for tactical operation

(U) Mean Time-to-Repair

(U) MTTR includes all repair time and downtime associated with the failure of the system except for the logistics of spare parts. MTTR is exclusive of Government Furnished Equipment (GFE).

(U) Scheduled or Preventive Maintenance

(U) Scheduled or preventive maintenance is systematic action deemed necessary to reduce or eliminate failures, prolong operating time, and prolong the useful life of the equipment. Periods of scheduled maintenance resulting in system down time are not used in determining Availability, MTBCF, or MTTR.

(U) Acronyms

(U) ABT

(U) Air Breathing Target

(U) ATG

(U) Antenna Transmitter Group

(U) AUX

(U) Auxiliary

(U) C2

(U) Command and Control

(U) dB

(U) Decibel

(U) dBi

(U) Decibels Above Isotropic

(U) ECP

(U) Engineering Change Proposal

(U) EDM

(U) Engineering Development Model

(U) EDT

(U) Engineering Development Testing

(U) EMI

(U) Electromagnetic Interference

(U) FAT

(U) First Article Test

(U) FUE

(U) Field User Evaluation

(U) GFE

(U) Government Furnished Equipment

(U) IFF

(U) Identification Friend or Foe

(U) MCTSSA

(U) Marine Corps Tactical Systems Support Activity

(U) MTBCF

(U) Mean Time Between Critical Failures

(U) MTTR

(U) Mean Time to Repair

(U) PQT

(U) Production Qualification Test

(U) RF

(U) Radio Frequency

(U) RPM

(U) Revolutions Per Minute

(U) RTM

(U) Requirements Traceability Matrix

(U) SLS

(U) Side Lobe Suppression

(U) SOW

(U) Statement of Work

(U) T&E

(U) Testing and Evaluation

(U) TRR

(U) Test Readiness Review

(U) VCRM

(U) Verification Cross Reference Matrix

(U) VSWR

(U) Voltage Standing Wave Ratio

UNCLASSIFIED