ITB-W-1528 A-1_Specs and Details-22x34.pdf

A-100

AS NOTED

SPECIFICATIONS

AND NOTES

SPECIFICATIONS:

GENERAL REQUIREMENTS:

1. CONTRACTOR SHALL COORDINATE ALL WORK PRIOR TO INSTALLATION OR

FABRICATION OF ANY COMPONENTS. ALL OPENINGS SHALL ALSO BE

COORDINATED WITH REFERENCE DRAWINGS.

2. ALL WORK MUST CONFORM TO ALL STATUTES OF THE MICHIGAN BUILDING

CODE (EDITION IN EFFECT AT THE TIME OF PERMIT), ALL STATE, COUNTY AND

LOCAL ORDINANCES, CURRENT BARRIER FREE REGULATIONS, MIOSHA

STRUCTURAL GUIDELINES, ASTM STANDARD TESTING PROCEDURES, OWNER'S

PRACTICES AND GENERALLY ACCEPTED DESIGN PRACTICES. IF

DISCREPANCIES IN DRAWING APPEAR, WORK MUST BE DONE PER CODE.

3. EXISTING CONDITIONS OF BUILDING SHOWN ON CONSTRUCTION DOCUMENTS

ARE ILLUSTRATIVE OF CONDITIONS VISIBLE TO ARCHITECT AND BASED ON

EXISTING DRAWINGS. ALL EXISTING DIMENSIONS, CONDITIONS, SIZES &

LOCATIONS ARE TO BE FIELD VERIFIED.

4. THE CONTRACTOR SHALL KEEP THE SITE IN A NEAT AND ORDERLY CONDITION

AND SHALL REMOVE RUBBISH DAILY OR AS DIRECTED BY OWNER. DUST

CONTROL MEASURES ARE TO BE ERECTED BY THE CONTRACTOR TO PROTECT

PATRONS AND VEHICLES DURING DEMOLITION AND CONSTRUCTION ACTIVIES.

ALL STAGING AND MATERIALS STORAGE IS TO BE COORDINATED WITH THE

OWNER. THE CONTRACTOR SHALL TAKE PRECAUTIONS TO ISOLATE

CONSTRUCTION ACTIVITIES FROM ADJACENT AREAS THAT ARE TO REMAIN IN

OPERATION DURING CONSTRUCTION - CONFIRM SCHEDULE AND REQUIRED

BARRICADES WITH OWNER PRIOR TO COMMENCEMENT.

5. CONTRACTOR SHALL PROVIDE NEW OPENINGS AND SUPPORTS AS NOTED.

FINAL OPENING DIMENSIONS, CONNECTION SIZES, CLEARANCES, ETC. MUST BE

COORDINATED DURING CONSTRUCTION WITH APPROVED COMPONENTS. SEAL

TIGHT ALL OPENINGS (ROOF, WALL AND CEILING), EQUIPMENT AND/OR

PENETRATIONS - FROM AIR AND MOISTURE. MATCH EXISTING FINISHES. FIRE

CAULK AND SEAL ALL NEW RATED PENETRATIONS.

6. REFER TO SPECIFICATIONS FOR ADDITIONAL INFORMATION AND APPROVED

MANUFACTURERS.

7. ALL INSTALLATIONS TO BE COORDINATED WITH EXISTING CONDITIONS FOR

PROPER SIZE, LOCATION AND PROVISIONS REQUIRED TO INSTALL

COMPONENTS.

8. PIPING & CONDUIT HANGERS AND SUPPORT LOCATION ARE NOT SHOWN ON

DRAWINGS. THE CONTRACTOR SHALL PROVIDE THE PIPING AND CONDUIT

HANGERS AND SUPPORTS NECESSARY AS REQUIRED PER CODE.

9. PATCH AND REPAIR EXISTING WALLS, FLOORS, & CEILINGS FOR SEAMLESS,

LIKE NEW APPEARANCE. THIS ALSO APPLIES TO DAMAGES THAT OCCUR AS

PART OF THE CONSTRUCTION PROCESS - RETURN AFFECTED AREAS TO

ORIGINAL CONDITIONS. CAREFULLY CUT HOLES IN CEILINGS AND WALLS TO

ACCOMMODATE INSTALLATION OF PIPING - REPAIR OPENINGS TO SEAMLESS,

LIKE NEW APPEARANCE AND PAINT TO MATCH ADJACENT SURFACES.

10. EXTEND CONDUIT AND PIPING AS REQUIRED TO ACCOMMODATE NEW WORK -

PROVIDE NEW & REPAIR EXISTING AS REQUIRED.

11. PROVIDE ADDITIONAL BLOCKING TO MATCH EXISTING AT WALLS/ CEILINGS TO

ACCOMMODATE NEW INSTALLATIONS. MAINTAIN FIRE RATED ASSEMBLIES AND

FIRE STOPPING PER LOCAL GOVERNING CODES AND ORDINANCES.

12. CONTRACTOR SHALL PROVIDE ALL REQUIRED TRANSITIONS, FITTINGS AND

APPURTENANT CONNECTIONS.

13. CONFIRM ANY COLOR SELECTIONS WITH OWNER.

14. SHOP DRAWINGS AND PRODUCT DATA - THE CONTRACTOR SHALL SUBMIT TO

THE OWNER AND PROJECT ENGINEER, SHOP DRAWINGS & PRODUCT DATA

SUBMITTALS FOR ALL PRODUCTS AND COMPONENTS TO BE USED ON THIS

PROJECT. MAINTAIN ONE COPY OF ALL APPROVED SUBMITTALS AT THE SITE

FOR THE OWNER'S REFERENCE.

15. "RECORD" DRAWINGS - THE CONTRACTOR SHALL MAINTAIN A SET OF

"AS-BUILT" PRINTS, MARKED UP AT THE SITE, CONTAINING ALL "AS-BUILT"

INFORMATION. TURN SET OVER TO OWNER UPON COMPLETION OF THE WORK.

16. INSTALL ALL MATERIALS IN COMPLIANCE W/ MFR. RECOMMENDATIONS AND

CODE REQUIREMENTS.

17. WORKING HOURS AT BUILDINGS ARE BE DETERMINED WITH OWNER AT START

OF PROJECT.

18. ALL REMAINING WALLS ARE TO BE PATCHED SMOOTH PRIOR TO PAINTING FOR

A SMOOTH, UNBLEMISHED APPEARANCE.

19. CONTRACTOR MUST VERIFY ALL EXISTING UTILITY LOCATIONS PRIOR TO

START OF DEMOLITION AND MAKE EVERY EFFORT TO PROTECT THEM OR

RELOCATE AS REQUIRED.

20. CONTRACTORS TO REFER TO ENTIRE SET OF DRAWINGS AND SPECIFICATIONS

FOR FULL SCOPE OF WORK. CROSS COORDINATION BETWEEN CIVIL,

PROCESS, MECHANICAL, ELECTRICAL, STRUCTURAL AND ARCHITECTURAL

DRAWINGS IS REQUIRED.

APPROVED

CHECKED

DRAWN

DESIGNED

DATE

HRC JOB NO.

DATE

SCALE

ADDITIONS AND/OR REVISIONS

SHEET

NO.

OF

555 HULET DRIVE

BLOOMFIELD HILLS, MICH.

P.O. BOX 824

48303 - 0824

PHONE: (248) 454-6300

WEB SITE: www.hrcengr.com

FAX (1st. Floor): (248) 454-6312 FAX (2nd. Floor): (248) 454-6359

CITY OF WARREN

CITY HALL LIBRARY

MEETING ROOM

IMPROVEMENTS

ITB - W - 1528

MCM

AMM

QR

AMM

AFFECTED

AREA

04-08-25 ISSUED FOR BID

A/V SPECIFICATIONS:

SCOPE OF WORK: VIEWING ROOM

VIDEO MONITOR: INSTALL AN LG 86UL3J-B 86 MONITOR JUST ABOVE THE FAUX

FIREPLACE UTILIZING A SANUS VLF628-B1 WALL MOUNT CAPABLE OF BEING

POSITIONED APPROXIMATELY 24 FORWARD OF THE WALL JUST IN FRONT OF THE

EXISTING BOOKCASE. THE MONITOR WILL BE CENTERED ON THE MANTLE BELOW.

EQUIPMENT LOCATION: THE EQUIPMENT WILL BE LOCATED DIRECTLY BEHIND THE

LG MONITOR ON A COMPONENT MOUNTING PLATE. PLENUM RATED18/2 SPEAKER

WIRE WILL RUN INTO THE CEILING PLENUM SPACE DIRECTLY OVERHEAD OF THE

ROOM TO BE DAISY CHAINED WITH SIX (6) JBL LCT-81C/T 2X2 TILE REPLACEMENT

SPEAKERS TAPPED AT 5 WATTS EACH, WHICH WILL PROVIDE SUPERIOR

INTELLIGIBILITY AT EVEN LOW VOLUME LEVELS WHILE BLENDING SEAMLESSLY INTO

THE SURROUNDING CEILING TILES.

SYSTEM OPERATIONAL OVERVIEW:

THE SYSTEM OPERATION WILL BE FULLY AUTOMATED AS FOLLOWS.

POWER ON THIS WILL OCCUR WHEN:

1. THE SYSTEM SENSES A SOURCE INPUT SIGNAL WIRELESSLY AT THE

SCREENBEAM 1100 PLUS WIRELESS INTERFACE USING A LAPTOP, TABLET OR

APPLE / ANDROID PHONE.

2. THE SYSTEM SENSES AN INPUT SIGNAL FROM A DIRECT HDMI CONNECT AT THE

WALL INPUT LOCATION.

IN EITHER SCENARIO, THE SYSTEM INCLUDING VIDEO MONITOR WILL

AUTOMATICALLY POWER UP WHEN A SIGNAL IS SENSED.

VOLUME AND ANY INTERACTION WITH THE VIDEO ON DISPLAY ARE CONTROLLED

FROM THE SOURCE DEVICE.

POWER OFF THIS WILL OCCUR WHEN:

THE SYSTEM TIMER HAS NOT RECEIVED A SIGNAL IN APPROXIMATELY 25 MINUTES,

THE ENTIRE SYSTEM WILL POWER DOWN.

VOLUME CONTROL, PLAY PAUSE, FFWD, RWND

THESE FUNCTIONS ARE CONTROLLED FROM THE USER (PRESENTERS) SOURCE

DEVICE (COMPUTER, TABLET OR PHONE) VOLUME UP /DOWN MAY ALSO BE

CONTROLLED WITH LG DISPLAY MONITORS REMOTE CONTROL (INCLUDED)

PROJECT FINISH:

THE SPACE SHALL BE CLEANED AND ANY FURNITURE MOVED SHALL BE RETURNED

TO ORIGINAL PLACEMENT UPON PROJECT COMPLETION.

WARRANTY:

THE COMPLETE INSTALLATION WILL BE COVERED BY A 3 YEAR PARTS & LABOR

WARRANTY.

SYSTEM TRAINING:

TRAINING WILL BE PROVIDED AT PROJECT FINISH WITH LIBRARY STAFF.

GENERAL NOTES

1. THE CONTRACTOR SHALL BE RESPONSIBLE FOR PULLING ALL PERMITS

NECESSARY FOR THE PROJECT. THE PERMIT FEES SHALL BE WAIVED BY THE

CITY.

2. ALL ELECTRICAL WORK SHALL COMPLY WITH THE NATIONAL ELECTRIC CODE

(N.E.C.), N.F.P.A., O.S.H.A., LOCAL AND STATE CODES, ORDINANCES AND

REGULATIONS.

3. ALL POWER WIRING 120 VOLTS AND GREATER SHALL BE INSTALLED IN CONDUIT

AND SHALL BE NEW. UNLESS NOTED OTHERWISE, ELECTRICAL METALLIC TUBING

(EMT) SHALL BE USED WHERE CONDUIT IS EXPOSED. CONDUIT ABOVE CEILING

OR IN WALLS MAY BE EMT OR METAL CLAD (MC) CABLE.

4. ALL CONDUITS SHALL BE ROUTED TO AVOID OPENINGS IN FLOORS, ROOFS, AND

WALLS. LADDERS UP WALLS SHALL NOT BE CROSSED BY EXPOSED CONDUIT

RUNS. PROVIDE THE MINIMUM CLEAR SPACE REQUIRED BY ALL GOVERNING

CODES BETWEEN HANDRAILS AND ALL ELECTRICAL ENCLOSURES AND

RACEWAYS, WHICH IN NO CASE SHALL BE LESS THAN 1 1/2" CLEAR.

5. WHERE NEW WALLS ARE TO BE INSTALLED, NEW CONDUIT SHALL BE RUN

CONCEALED IN THE WALL. RECEPTACLES AND SWITCHES SHALL BE FLUSH

MOUNTED. WHERE RECEPTACLES AND SWITCHES ARE INSTALLED ON EXISTING

WALLS OR AREAS, DEVICES SHALL BE SURFACE MOUNTED, AND CONDUIT SHALL

BE RUN SURFACE MOUNTED.

6. PROVIDE A GREEN GROUND CONDUCTOR IN ALL SYSTEMS CONDUITS. GROUND

CONDUCTOR SIZING SHALL BE PER NEC TABLE 250.122 WHERE NOT SIZED ON

THE DRAWINGS.

7. ALL MATERIALS USED SHALL BE NEW AND BEAR THE U.L. LABEL WHERE SUCH

SERVICE AND LABEL ARE REGULARLY PROVIDED AND BE OF THE APPROPRIATE

NEMA STANDARD.

8. THE CONTRACTOR SHALL FURNISH ALL MATERIALS AND LABOR AS INDICATED ON

PLANS AND AS REQUIRED FOR A COMPLETE, REVISED ELECTRICAL SYSTEM.

9. COORDINATE EXACT LOCATION OF ALL LIGHTING FIXTURES AND OTHER

ELECTRICAL DEVICES WITH MECHANICAL EQUIPMENT, PIPING, AND DUCTWORK

BEFORE INSTALLATION.

10. ALL THREADED ELECTRICAL EQUIPMENT (CONDUIT, FITTINGS, BOLTS, SCREWS,

ETC.) SHALL BE COATED WITH ANTI-SEIZE COMPOUND PRIOR TO INSTALLATION.

ALL HARDWARE SHALL BE STAINLESS STEEL.

11. EACH OF THE SPECIFIED EQUIPMENT SHALL BE SUBMITTED FOR APPROVAL BY

REFERENCE TO MANUFACTURER AND SPECIFIC CATALOG AND MODEL NUMBER.

12. THE CONTRACTOR SHALL VISIT THE JOB SITE, THOROUGHLY CHECK THE

EXISTING FIELD CONDITIONS AND EXISTING ELECTRICAL INSTALLATIONS, AND

CLARIFY ALL DISCREPANCIES WITH THE ENGINEER BEFORE SUBMITTING A BID,

AS NO EXTRAS WILL BE ALLOWED FOR OMITTED WORK DUE TO FAILURE TO

INSPECT THE PREMISES.

13. ON COMPLETION OF WORK AND BEFORE FINAL PAYMENT IS MADE, THIS

CONTRACTOR SHALL PREPARE "AS-BUILT DRAWINGS". CLEARLY INDICATE ON A

SET OF CONTRACT DRAWINGS ALL THE CHANGES MADE DURING

CONSTRUCTION, DUE TO FIELD CONDITIONS, ADDENDA, BULLETINS, ETC.

DRAWINGS SHALL INDICATE THE INSTALLED LOCATION OF ALL EQUIPMENT,

OUTLETS, ETC.

14. WHEN THE JOB IS COMPLETE, CONTRACTOR SHALL PROVIDE THE OWNER WITH

CERTIFICATE OF APPROVAL FROM THE ELECTRICAL INSPECTION AUTHORITY

AND SHALL PROVIDE THE OWNER WITH A ONE YEAR WRITTEN GUARANTEE ON

ALL NEW MATERIALS AND LABOR.

15. RE-SUPPORT EXISTING CONDUIT, BOXES, ETC. WHERE CEILING OR SUPPORT

REVISIONS NECESSITATES NEW SUPPORTS. ALL WORK SHALL BE COORDINATED

WITH OTHER DISCIPLINES.

16. ALL DEMOLISHED ITEMS SHALL BE DISPOSED OF AWAY FROM THE SITE.

BASIC MATERIALS AND METHODS

1. WIRE FOR GENERAL USE SHALL BE COPPER, TYPE THHN/THWN, 90 DEGREES C.

ALUMINUM WIRE SHALL NOT BE USED. ALL WIRE SHALL BE RATED AT 600 VOLTS,

WET AND DRY LOCATION, MINIMUM SIZE NO. 12 A.W.G. INSTALLED IN CONDUIT,

SIZED AS SHOWN ON THE DRAWINGS, MINIMUM SIZE 3/4".

2. BOXES SHALL BE GALVANIZED STEEL, CODE THICKNESS, A MINIMUM OF 1" DEEP

AND OF SUFFICIENT SIZE TO ACCOMMODATE THE DEVICES THEY SERVE,

ACCORDING TO N.E.C. REQUIREMENTS. PULL BOXES FOR ALL CONDUIT RUNS

FOR ALL SYSTEMS SHALL BE INSTALLED AT INTERVALS NOT EXCEEDING 100

FEET OR AFTER 270 DEGREES OF BENDS.

3. CONDUITS SHALL NOT BE SUPPORTED FROM MECHANICAL DUCTS, PIPE, OR PIPE

AND DUCT SUPPORTS.

4. ELECTRIC SYSTEM GROUNDING SHALL IN ALL INSTANCES COMPLY WITH THE

MINIMUM REQUIREMENTS OF THE N.E.C. ALL CONDUITS SERVING WIRING OF 120

VOLTS OR GREATER SHALL INCLUDE A GROUND WIRE.

5. ELECTRICAL ENCLOSURES, CONDUIT SYSTEMS, ETC., SHALL BE THOROUGHLY

GROUNDED IN ACCORDANCE WITH THE N.E.C. AND ALL LOCAL CODES.

6. ALL CONDUITS SHALL BE ROUTED TO AVOID OPENINGS IN FLOORS, ROOFS, AND

WALLS. LADDERS UP WALLS SHALL NOT BE CROSSED BY EXPOSED CONDUIT

RUNS. PROVIDE THE MINIMUM CLEAR SPACE REQUIRED BY ALL GOVERNING

CODES BETWEEN HANDRAILS AND ALL ELECTRICAL ENCLOSURES AND

RACEWAYS, WHICH IN NO CASE SHALL BE LESS THAN 1 1/2" CLEAR.

7. FOR ALL 120 VAC LIGHTING AND RECEPTACLE CIRCUITS, RUN 2-#12 (MINIMUM) +

#12 GRD., 1/2"C. TO THE LIGHTING PANELBOARD INDICATED, UNLESS NOTED

OTHERWISE.

8. GFI DUPLEX RECEPTACLES SHALL BE 125 VOLT, 3 WIRE GFCI TYPE WITH FACE

MOUNTED TEST AND RESET BUTTONS AND MATCHING STAINLESS STEEL COVER

PLATE, HUBBELL HBL GF-5362-I, LEVITON 6898-I, OR EQUAL. ALL SWITCHES AND

RECEPTACLES SHALL BE PROVIDED WITH STAINLESS STEEL COVER PLATES.

9. DUPLEX RECEPTACLES SHALL BE 20 AMP, 125 VOLT, 3 WIRE, GROUNDING TYPE

BY HUBBELL, GE, COOPER, OR EQUAL.

10. SWITCHES AND RECEPTACLES SHALL BE PROVIDED WITH COVER PLATES -

CONFIRM COLOR/FINISH WITH OWNER, MATCH EXISTING AS NOTED. SWITCHES

AND RECEPTACLES TO BE SURFACE MOUNTED SHALL BE INSTALLED IN METAL

BOXES.

11. CIRCUIT BREAKERS FOR PANELBOARDS SHALL BE OF THE BOLT-IN-PLACE OR

STAB-IN TYPE USING SINGLE POLE OR COMMON TRIP, TWO OR THREE POLE AS

INDICATED ON THE DRAWINGS. CIRCUIT BREAKERS SHALL BE ON MOLDED CASE

TYPE WITH THERMAL MAGNETIC TRIP AND BREAKER HANDLES INDICATING "ON" -

"OFF" AND "TRIP" POSITIONS. GROUND FAULT CIRCUIT INTERRUPTER (GFCI)

TYPE BREAKERS SHALL BE PROVIDED WHERE INDICATED ON THE DRAWINGS.

BREAKERS SHALL HAVE 22,000 AMPERE INTERRUPTING CAPACITY MINIMUM AND

SHALL BE APPROVED FOR "SWITCHING DUTY." ALL CIRCUIT BREAKERS SHALL BE

LOCKABLE. CIRCUIT BREAKERS SHALL BE EATON-CUTLER-HAMMER, SQUARE D

BY SCHNEIDER ELECTRIC, OR ABB.

12. WHERE INDICATED ON THE DRAWINGS, PROVIDE MODIFICATIONS TO EXISTING

PANELBOARDS AS REQUIRED. PANELBOARDS SHALL BE MODIFIED BY THE

ADDITION OF NEW DEVICES, CONNECTIONS TO EXISTING DEVICES, AND/OR

DISCONNECTION FROM EXISTING DEVICES. CIRCUIT BREAKERS FOR ADDITION

TO EXISTING PANELBOARDS SHALL BE THE PANELBOARD MANUFACTURER'S

COMPATIBLE REPLACEMENT PARTS AND SHALL MATCH THE PANELBOARD'S

EXISTING BREAKER INTERRUPTING RATINGS. BREAKER TRIP RATINGS AND

NUMBER OF POLES SHALL BE INDICATED ON THE DRAWINGS.

13. SWITCHES SHALL BE QUIET, QUICK MAKE, SLOW BREAK DESIGN WITH TOTALLY

ENCLOSED CASE, FLUSH TYPE, TOGGLE SWITCHES, 20 AMPERE CAPACITY AT

120/277 VOLTS, SINGLE POLE OR 3-WAY AS INDICATED ON THE DRAWINGS.

LIGHTING SWITCHES SHALL BE HUBBELL SERIES HBL 1220, LEVITON SERIES 1220,

GENERAL ELECTRIC GE5951, COOPER WIRING DEVICES OR EQUAL.

14. ALL CONDUIT RUNS (POWER AND CONTROL) SHALL BE LABELED IN ACCORDANCE

WITH ANSI 13.1 WITH LABELS THAT ARE WATER-RESISTANT. CIRCUIT NUMBER

MARKERS SHALL CONSIST OF SELF-ADHESIVE VINYL CLOTH OR POLYVINYL

FLOURIDE FILM MARKERS WITH 1/8" HIGH (MINIMUM), BLACK LETTERING ON A

YELLOW BACKGROUND, W.H. BRADY CO. MARKERS MAY ALSO CONSIST OF

COMPUTER GENERATED, VINYL CLOTH, PERMANENT, NON-SMEARING,

SELF-ADHESIVE MARKERS SUCH AS BRADY DATAB, BRADYMARKER XC PLUS, 3M

SCOTCHCODE SCS OR STS, OR EQUAL. CIRCUIT NUMBER MARKERS FOR

PANELBOARD CIRCUIT BREAKERS MAY BE THE MANUFACTURER'S STANDARD.

ELECTRICAL SPECIFICATIONS:

AutoCAD SHX Text 2025 Hubbell, Roth & Clark, Inc. All Rights Reserved

AutoCAD SHX Text C

AutoCAD SHX Text V:\202402\20240248\A\Sheets\A-1_Specs and Details.dwg

AutoCAD SHX Text Reed, Qetuwrah

AutoCAD SHX Text

AutoCAD SHX Text

4/15/2025 8:52 AM

AutoCAD SHX Text 20240248

AutoCAD SHX Text April 2025

AutoCAD SHX Text

ORIGINAL PLOT SIZE: ANSI FULL BLEED D (34.00 X 22.00 INCHES)