Installation Criteria Visual Guidance Lighting Systems.pdf

8/20/10 JO 6850.2B

Table of Contents

Paragraph Page

CHAPTER 1. GENERAL INFORMATION AND REQUIREMENTS 1-1

SECTION 1. GENERAL 1-1

1. Purpose of this Order 1-1

2. Audience 1-1

3. Where Can I Find This Order 1-1

4. Cancellation 1-1

5. Explanation of Policy Changes 1-1

6. Application 1-1

7. Deviation From Standards 1-1

8. FAA-Military Joint-Use Agreement 1-1

9. Flight Inspection 1-2

10. Visibility Requirements 1-2

11. Corrections to Installation Criteria 1-2

SECTION 2. VISUAL GUIDANCE LIGHTING SYSTEM 1-2

12. Introduction 1-2

13. Development of Visual Facilities 1-2

14. Definitions 1-2

15. Approach Lighting Systems (ALS) 1-3

16. Reserved 1-4

17. Runway End Identifier Lights (REIL) 1-4

18. Lead-in Lighting System (LDIN) 1-4

19. Precision Approach Path Indicator (PAPI) 1-5

20. Land Requirements for Approach Lighting Systems 1-5

21. Remote Radio Control 1-5

22. Distribution 23 – 199. Reserved

1-6 1-6

CHAPTER 2. INSTALLATION CRITERIA - APPROACH LIGHTING

SYSTEM (ALS)

2-1

200. System Configuration 2-1

201. Ideal Installation 2-9

202. Permissible Deviations 2-11

203. Use of Various Types of Lights 2-17

204. Lighting Fixtures 2-17

205. Control and Monitoring Requirements 2-18 ii

206. Vertical Alignment 2-19

207. Horizontal Alignment 2-19

208. Penetration of Approach Surface 2-19

209. Miscellaneous Provisions 2-22

210. Brightness Steps 2-22

211. Displaced Threshold Lighting 2-22

212. Floodplain Low Impact Resistant (LIR) Installation 2-22

CHAPTER 3. RESERVED 3-1

CHAPTER 4. INSTALLATION CRITERIA - RUNWAY END

IDENTIFIER LIGHTS (REIL)

4-1

400. Description 4-1

401. Location of Light Units 4-1

402. Orientation of Light Units 4-1

403. Lighting Fixtures 4-1

404. Power Source 4-3

405. Control 4-3

406. Monitoring 4-3

CHAPTER 5. INSTALLATION CRITERIA - PRECISION APPROACH

PATH INDICATOR (PAPI)

5-1

500. Description 5-1

501. General Siting Considerations 5-1

502. Siting PAPI on a Runway with an Electronic ILS Glide Slope 5-1

503. Siting PAPI on a Runway without an Electronic ILS Glide Slope 5-5

504. Aiming 5-6

505. Other Siting Dimensions and Tolerances 5-6

506. PAPI Assemblies 5-10

507. Remote Control 5-10

508. Monitoring 5-10

509. Deviations 5-10

APPENDIX A. JOINT USE AGREEMENT A-1

1. Type of system to be Installed A-1

2. Selection of System to be Installed A-1

3. Installation Standards A-1

4. Operation and Maintenance A-2

5. Reimbursement of FAA by ANG A-2

6. Coordination A-4

APPENDIX B. REMOTE CONTROL FOR VISUAL GUIDANCE

LIGHTING SYSTEMS

B-1 iii

1. Purpose B-1

2. Background B-1

3. Definitions B-1

4. Radio Control System Operation B-2

5. Equipment Requirements B-2

6. Radio Control Selection B-3

7. Coordination Requirements B-4

8. Non-FAA Radio Control Systems B-5

APPENDIX C. REMOTE RADIO CONTROL BACKGROUND C-1

APPENDIX D. FLOODPLAIN LOW-IMPACT RESISTANT (LIR)

INSTALLATION

D-1

APPENDIX E. VISUAL APPROACH SLOPE INDICATOR (VASI)

SYSTEM CONFIGURATION AND INSTALLATION

E-1

SECTION 1. VISUAL APPROACH SLOPE INDICATOR (VASI)

SYSTEM CONFIGURATIONS

E-1

1. Visual Approach Slope Indicator System E-1

SECTION 2. VISUAL APPROACH SLOPE INDICATOR (VASI)

SYSTEMS INSTALLATYION CRITERIA

E-2

2. Description E-2

3. Determining Obstruction Clearance E-3

4. Visual Glide Path Angle E-3

5. Two-Bar VASI Light bar Locations E-11

6. Three-Bar VASI Light Bar Locations E-11

7. Aiming VASI Light Bars E-12

8. Installation of Light Units E-12

9. Remote Control and Monitoring Requirements E-13

10. Miscellaneous Requirements E-13

List of Figures

Figure Page

2-1 ALSF-2 Configuration 2-2 2-2 SSALR Configuration 2-4 2-3 MALS and MALSF Configuration 2-5 2-4 MALSR Configuration 2-7 2-5 ODALS Configuration 2-8 2-6 Ideal RAIL Obstruction Clearance 2-10 2-7 RAIL Obstruction Clearance for +2.0% Slope 2-13 iv v

2-8 RAIL Obstruction Clearance for -2.5% Slope 2-14 2-9 Typical RAIL Obstruction Clearance for Two Sloping Segments 2-15 2-10 Correction of Elevation-Setting Angle for Approach Lights

Displaced from the Horizontal Plane Passing Through the Threshold

2-21

4-1 REIL Configuration 4-2 5-1 PAPI System Configuration 5-2 5-2 PAPI Visual Cues 5-3 5-3 PAPI Approach Path (side view) 5-4 5-4 PAPI Obstacle Clearance Surface 5-7 5-5 Correction for Runway Longitudinal Gradient 5-9

List of Tables

Table Page

2-1 Elevation-Setting Angles for Q20A/PAR56 Approach Light

Lamps (ALSF-2) 2-20

2-2 Elevation-Setting Angles for 150PAR38/SP Approach Light Lamps (MALS)

2-20

2-3 Brightness Steps 2-23 5-1 Visual Threshold Crossing Heights 5-5 5-2 Aiming of PAPI Relative to a Preselected Glide Path 5-6

CHAPTER 1. GENERAL INFORMATION AND REQUIREMENTS

Section 1. General

1. Purpose of this Order. This order contains installation criteria for all visual guidance lighting systems installed under the Facilities and Equipment (F&E) Program.

2. Audience. This order is intended for use by the Air Traffic Organization (ATO) Service Centers and the Technical Operations engineers for the implementation of Visual Guidance Lighting Systems in the National Airspace System (NAS).

3. Where can I find this order. You can find this order on the My FAA Employee website.

Select Tools & Resources, and then select Orders and Notices.

4. Cancellation. This order cancels Federal Aviation Administration (FAA) Order 6850.2A including Changes 1 through 4 dated 2/8/89.

5. Explanation of Policy Changes. FAA Order 6850.2A was updated to provide clarification and include additional definitions to specific requirements. This order was revised to Revision B and includes Changes 1 through 4, dated February 8, 1989. Editorial changes were incorporated to comply with the U.S. Government Printing Office Style Guide. Several paragraphs in the order were modified as a result of comments received from must evaluators during the Clearance Record review process. The REIL Flight Inspection information was added to Chapter 4. Appendices D and E were added. Chapter 3 is now included in Appendix E and Appendix D includes the requirements for the Low Impact Resistant structures mounted in flood plain areas.

6. Application. The requirements of this Order shall be applied to all new establishment projects for visual guidance lighting systems, for previously commissioned systems that are to be relocated, and for systems to be modified to conform to the configuration of another system.

Modification of existing systems for the sole purpose of conforming to new requirements is not required.

7. Deviation from Standards. All deviations from the installation criteria contained in this directive must be covered by a waiver. Waivers shall be processed in accordance with the latest edition of FAA Order 1800.66, Configuration Management Policy. All deviation from the standard installation criteria shall be coordinated with the Office of Flight Operations. Systems existing and installed under previous criteria do not need a waiver to the criteria contained in this document because the criteria herein apply only to new and relocated systems, and systems being modified.

8. FAA/Military Joint-Use Agreement. An agreement for establishing approach lighting systems at joint-use airfields has been agreed to by the Air National Guard (ANG) and the (FAA). This agreement supersedes the previous agreement of June 1959, and is included as Appendix A. Joint-use airports are listed in the latest edition of Order 5000.5, List of Joint-use Airports.

1-1

9. Flight Inspection. Before commissioning, all visual guidance lighting systems, including VASI, PAPI, and REIL, installed at airports with a public-use or military instrument approach procedure will receive a commissioning flight inspection to ensure that the system meets the requirements of the latest edition of FAA Order 8200.1, U.S. Standard Flight Inspection Manual.

10. Visibility Requirements. Visibility requirements for visual guidance lighting systems can be found in the latest version of FAA Order 8260.3, United States Standard for Terminal Instrument Procedures (TERPS).

11. Corrections to Installation Criteria. Corrections to the installation criteria may be made by the Director, Navigation Services, in coordination with the Office of Flight Operations, without further regional or additional interservice coordination. These may include misspellings, corrections of dimensional errors, and modification, addition or deletion of minor details.

Section 2. Visual Guidance Lighting System

12. Introduction. The term visual guidance lighting system is used for identifying, as a type of facility, those configurations of lights located on and in the vicinity of an airfield to provide pilots with a visual reference for guidance purposes while operating an aircraft during approach for landing. These facilities are visual aids to the pilot and may be used with or without electronic landing aids, such as an Instrument Landing System (ILS), etc.

13. Development of Visual Facilities. Visual guidance lighting systems are designed and provided to improve the operational safety of aircraft during approach and landing operations. In order to meet this objective, the configurations, colors, equipment, and materials used for the various facilities must be consistent with and suited to the operational requirements of the aircraft. Consequently, these facilities must be reviewed constantly to ensure that they satisfy the changing operational procedures. New engineering developments, new materials, and improvements in manufacturing processes are also reviewed continuously, and where judged superior to those in use, that is technically better, more cost-effective, state-of-the-art, more reliable, or maintainable, are incorporated for use in visual guidance lighting systems.

14. Definitions. The following terms used herein are defined as follows:

a. Approach Lighting System (ALS) Centerline. The ALS centerline is the extended centerline of the runway being served.

b. Landing Threshold. A line perpendicular to the runway centerline marking the beginning of the runway surface that is available for landing of an aircraft.

c. Approach Light Plane. An imaginary horizontal plane that passes through the beam centers of the lights in the system. The plane is rectangular in shape, centered on the ALS centerline, originating at the landing threshold, and extending 200 feet beyond the last light (at the approach end of the system). The width varies according to the lighting system.

1-2

d. Light Bar. A cluster of signal lights arranged in a row perpendicular to the runway centerline.

e. Semiflush Lights. Lights designed for installation in paved areas and do not extend more than one inch above the surrounding paved area and capable of roll-over by aircraft.

f. Frangible Lights. Lights mounted on structures up to 6 feet high, which are designed to present a minimum of mass and to break at the base when impacted.

g. Low-Impact Resistant Lights. Lights mounted on structures 6 to 40 feet high, which are low-impact resistant, designed to present a minimum of mass, and designed to break when impacted.

h. Semifrangible Lights. Lights mounted on two-element structures: the lower element being a rigid structure and the upper element being a 20-foot, low-impact resistant structure.

i. Rigid Lights. Lights installed on all rigid structures. These lights are not authorized on new construction.

j. Positive Slope. A slope of the approach light plane upward and outward from the landing threshold.

k. Negative Slope. A slope of the approach light plane downward and outward from the landing threshold.

l. Primary Plane. A plane that defines obstruction clearance for the RAIL portion of an approach lighting system.

m. Secondary Plane. Gradients adjacent to the primary plane that define obstruction clearance for the RAIL portion of an approach.

n. Visual Segment Method. The visual segment method for determining the alignment of approach lights is defined and completely described in Report No. FAA-RD-78-137, Approach Light Aiming Criteria, by Charles A. Douglas dated December 4, 1978 available from the National Technical Information Service; Springfield, VA 22161.

15. Approach Lighting Systems (ALS). An approach lighting system is a configuration of signal lights disposed symmetrically about the runway centerline extended, starting at the landing threshold and extending outward into the approach zone. This system provides visual information runway alignment, height perception, roll guidance, and horizon references. The system used for precision approaches (in conjunction with an electronic aid such as an ILS) is normally 2,400 feet in length when the glide slope is 2.75 degrees or greater, and 3,000 feet in length when the glide slope is less than 2.75 degrees. When installation of a 2,400 foot system is not possible, a system 1,400 feet in length may be installed on nonprecision runways. A complete description of the system configuration is given in chapter 2. The approach lighting system is classified as a high intensity or a medium intensity system, the distinction being made

1-3 on the type of lamps and equipment used. The following is a list of approach lighting systems and their intended use. The selection criteria for these systems for official planning purposes are contained in the latest edition of Order 7031.2, Airway Planning Standard Number One - Terminal Air Navigation Facilities and Air Traffic Services.

a. Medium Intensity Approach Lighting System (MALS). An economy type system for non precision approaches.

b. Medium Intensity Approach Lighting System with Sequenced Flashers (MALSF).

Same as MALS, but equipped with three sequenced flashers at locations where approach area identification problems exist.

c. Medium Intensity Approach Lighting System with Runway Alignment Indicator Lights (MALSR). An economy type system used as the FAA standard for category I precision runways.

d. Simplified Short Approach Lighting System with Runway Alignment Indicator Lights (SSALR). Used the same as MALSR. Generally, the SSALR is not to be installed as a new system. This configuration is used when category I conditions exist on category II designated runways with a dual mode approach lighting system (ALSF-2/SSALR).

e. High Intensity ALS with Sequenced Flashers (ALSF-2). Used on category II and III precision approach runways. FAA Headquarters approval is required before installing a new

ALSF-2.

f. Omnidirectional Approach Lighting System (ODALS). The ODALS is a configuration of seven omnidirectional sequenced flashing lights located in the runway approach area. The ODALS provides circling, offset, and straight-in visual guidance for nonprecision approach runways.

16. Reserved. The VISUAL APPROACH SLOPE INDICATOR (VASI) system is no longer installed by the FAA as a new facility. Specific details and installation criteria have been moved to Appendix E to provide technical support for existing VASI equipment and facilities.

17. Runway End Identifier Lights (REIL). The primary function of the REIL is to provide rapid and positive identification of the end of a runway. The system consists of two synchronized flashing lights, unidirectional or omnidirectional, one on each side of the runway landing threshold. The unidirectional flashing lights face the approach area. The flashing feature of the lights provides an attracting characteristic, making the REIL effective for identification of a runway surrounded by a preponderance of other lighting or lacking contrast with surrounding terrain.

18. Lead-In Lighting System (LDIN). The LDIN provides positive visual guidance along an approach path, either curving or straight, where special problems exist with hazardous terrain, obstructions, or noise abatement procedures. An LDIN consists of one or more series of flashing lights installed along the approach path at or near ground level. The series or groups of lights are

1-4 positioned and aimed so as to be conveniently sighted and followed from the approaching aircraft under conditions at or above approach minimums. Each light group shall contain at least three flashing lights in a linear or cluster configuration and may be augmented by steady-burning lights if required. Where practical, the lights comprising a given group shall flash in sequence toward the runway. The light groups shall be spaced closely enough together (approximately 1 mile) to provide continuous lead-in guidance along each segment of the approach course.

Sequencing of successive light groups is recommended. The LDIN may be terminated at any approved approach lighting system, or it may be terminated at a distance from the threshold compatible with authorized visibility minimums permitting visual reference to the runway environment. The design of all LDINs shall be compatible with the requirements of U.S.

Standards for Terminal Instrument Procedures (TERPS) where such procedures are applied for established instrument minimums.

19. Precision Approach Path Indicator (PAPI). The PAPI system provides visual approach slope information. The system provides a definite white and red light projection pattern along the desired descent path to the touchdown point. The PAPI system consists of two parts: (1) a single horizontal bar with four sharp transition multilamp units, referred to as lamp housing assemblies (LHA's), equally spaced, and (2) a power and control unit (PCU). The LHA's are located on a line perpendicular to the runway centerline, at a distance from the threshold chosen to provide the proper threshold crossing height and obstacle clearance. Each LHA projects a split beam of light, the upper segment being white and the lower segment being red. The transition from white to red, or vice versa, occurs within a vertical angle of 5 minutes of arc at the beam center and results in a well-defined corridor of light consisting of white (top) and red (bottom) beams. Details of the system configurations are covered in chapter 5.

20. Land Requirements for Approach Lighting Systems. The minimum land requirements for full-length approach lighting systems are as follows:

a. ALSF-2. 2,600 feet long by 400 feet wide.

b. MALS and MALSF. 1,600 feet long by 400 feet wide.

c. MALSR. The MALSR requires land that is 1,600 feet long by 400 feet wide for the MALS portion, plus an additional 1,000 feet in length by 25 feet in width for the runway alignment indicator light (RAIL) portion. The minimum width of 25 feet for the RAIL portion is considered adequate for relatively clear and level terrain. However, where required to meet visibility, obstruction clearances, and/or access requirements, the width may be increased to a maximum of 100 feet to meet the requirements of paragraph 201e. In some cases, the visibility or obstruction clearance requirement may be met by raising the RAIL structures. In such cases, an analysis should be made of the comparative cost of raising the structures versus acquiring additional land or removing obstructions, with the less expensive method being followed.

d. ODALS. The standard omnidirectional approach lighting system requires a rectangular surface 1,700 feet in length by a minimum width of 400 feet, beginning at the runway threshold and extending outward along the extended runway centerline.

1-5

CHAPTER 2. INSTALLATION CRITERIA - APPROACH LIGHTING SYSTEM (ALS)

200. System Configuration.

a. ALSF-2. This configuration is for category II and category III runways. The ALSF-2 consists of a light bar (approximately 13½ feet long with five equally spaced lights) at each 100-foot interval starting 100 feet from the runway threshold and continuing out to 2,400 feet from the threshold. All light bars are installed perpendicular to the extended runway centerline and all lights are aimed away from the runway threshold. The centerline light bar at 1,000 feet from the threshold is supplemented with eight additional lights on either side forming a light bar of 100 feet and containing 21 lights. This bar is called the 1,000-foot distance marker crossbar (or simply 1,000-foot bar). Also, there is a light bar (four white lights each) on each side of the centerline bar 500 feet from the threshold. These lights form a crossbar referred to as the 500 foot bar. All of the aforementioned lights are white. In addition, there are light bars (three red filtered lights each) on each side of the centerline bars at each light station in the inner 900 feet.

These are called side row bars. A row of green filtered lights on five foot centers is located within 10 feet of the threshold and extends across the runway threshold and outwards a distance of approximately 45 feet from the runway edge on each side of the runway. These lights are called the threshold bar. All lights are aimed into the approach to the runway and away from the runway threshold. The ALSF-2 configuration is shown in figure 2-1.

b. Sequenced Flashers for ALSF-2. In addition to the steady-burning lights, both configurations are augmented with a system of sequenced flashing lights. One such light is installed at each centerline bar starting 1,000 feet from the threshold out to the end of the system.

These flashing lights emit a bluish-white light and flash in sequence toward the threshold at a rate of twice per second. The flashing lights appear as a ball of light traveling toward the runway threshold. The flashing lights have three intensities coordinated with the intensity of the steady-burning light in the approach lighting system. All lights are aimed into the approach to the runway and away from the runway threshold.

2-1

1. LOCATE SIDE ROW BARS IN LINE WITH TDZ LIGHTS.

2. LOCATE 4-LIGHT BARRETTES EQUIDISTANT BETWEEN

SIDE ROW BARS AND CENTERLINE BARS.

RUNWAY CL

10' NORMALLY

RUNWAY LIGHTS

TOUCHDOWN ZONE LIGHTS

THRESHOLD BAR

45' 45'

STA. 1 + 00

STA. 5 + 00

STA. 10 + 00

STA. 14 + 00

STA. 24 + 00

10' MAX

100' +10' -0'

1000' ±50'

1400' +50' -0'

2400' +50' -0'

1000' BAR

9 SIDE ROW BARS -

ONE ROW EACH SIDE

OF ALS CENTERLINE

WITH 100' SPACING

24 CENTERLINE BARS

WITH 100' SPACING

SEE NOTE 2

15 SEQUENCED FLASHERS

USED ON STA 10

THROUGH STA 24

35' 35'

15'15'

RUNWAY CL

(CONTINUOUS ROW

OF GREEN LIGHTS

WITH 5' SPACING)

(3 RED LIGHTS WITH

5' SPACING, SEE NOTE 1)

(5 WHITE LIGHTS

WITH 40 12" SPACING)

(4 WHITE LIGHTS

WITH 5' SPACING)

8 WHITE LIGHTS

WITH 5' SPACING

SYMBOLS:

NOTES:

STEADY BURNING LIGHT, RED

HIGH INTENSITY STEADY BURNING LIGHT, WHITE

SEQUENCED FLASHING LIGHT

(ALIGNED WITH TOUCHDOWN ZONE ON RUNWAY)

RUNWAY THRESHOLD

STEADY BURNING LIGHT, GREEN, THRESHOLD LIGHT

FIGURE 2-1. ALSF-2 CONFIGURATION

2-2

c. SSALR. The SSALR configuration consists of a threshold bar and seven five-light bars located on the extended runway centerline with the first bar located 200 feet from the runway threshold, and the remaining bars at 200-foot intervals out to 1,400 feet from the threshold. Two additional five-light bars are located, one on each side of the centerline bar, 1,000 feet from the runway threshold forming a crossbar 70 feet long. The spacing between individual lights is 40½ inches for the centerline bars and five feet for other bars. All lights in the system are white except for the threshold lights. The threshold lights have green filters. The threshold lights are a row of lights on 10-foot centers located coincident with and within the runway edge lights near the threshold and extends across the runway threshold. The RAIL portion of the facility consists of five sequenced flashers located on the extended runway centerline, the first being located 200 feet beyond the approach end of the last steady-burning light bar with successive flasher units at each 200-foot interval out to 2,400 feet from the threshold. These flashing lights emit a bluish-white light and flash in sequence toward the threshold at a rate of twice per second. All lights are aimed into the approach to the runway and away from the runway threshold. The SSALR configuration is shown in figure 2-2. This configuration is operated as a subsystem of the ALSF-2.

d. MALS. The MALS consists of a threshold light bar and seven five-light bars located on the extended runway centerline with the first bar located 200 feet from the runway threshold, and the remaining bars at each 200-foot interval out to 1,400 feet from the threshold. Two additional five-light bars are located, one on each side of the centerline bar, 1,000 feet from the runway threshold forming a crossbar 66 feet long. The spacing between individual lights in all bars is approximately 2½ feet. All lights are aimed into the approach to the runway and away from the runway threshold. All lights in the system are white, except for the threshold lights.

These lights have green filters. The threshold lights are a row of lights on 10-foot centers located coincident with and within the runway edge lights near the threshold and extend across the runway threshold. The MALS configuration is shown in figure 2-3.

e. MALSF. The MALSF consists of a MALS with three sequenced flashers located at the last three light bar stations. These flashers are added to the MALS at locations where high ambient background lighting, or other reasons, requires these lights to assist pilots in making an earlier identification of the system. These lights flash in sequence toward the threshold at the rate of twice per second. All lights are aimed into the approach to the runway and away from the runway threshold. The MALSF configuration is shown in figure 2-3.

2-3

10' MAX

200' ±20'

1000' ±50'

1400' ±50'

2400' +50' -0'

+1' -0'10'

12 LIGHT

STATIONS @

200'±20'

SPACING

RUNWAY THRESHOLD

20' 20'15' 15'

13 1/2'

SYMBOLS:

STEADY BURNING LIGHT, GREEN

STEADY BURNING LIGHT, WHITE

FLASHING LIGHT

RUNWAY CL

RUNWAY CL

10' 10'

FIGURE 2-2. SSALR CONFIGURATION

2-4

1000'

10' 10'

10' MAX

200'

+1' -0'10'

RUNWAY THRESHOLD

10'

SYMBOLS:

STEADY BURNING LIGHT, GREEN

STEADY BURNING LIGHT, WHITE

SEQUENCED FLASHING LIGHT (FOR MALSF ONLY)

RUNWAY CL

RUNWAY CL

+100' -0'

+100' -0'

+100' -0'

28' 28'

7 CENTERLINE

BARS @

200'±20'

SPACING

FIGURE 2-3. MALS AND MALSF CONFIGURATION

2-5

f. MALSR. This configuration is for category I runways. The MALSR consists of a MALS plus RAIL. The RAIL portion of the facility consists of five sequenced flashers located on the extended runway centerline, the first being located 200 feet beyond the approach end of the MALS with successive units located at each 200-foot interval out to 2,400 feet from the runway threshold. These lights flash in sequence toward the threshold at the rate of twice per second. All lights are aimed into the approach to the runway and away from the runway threshold. The MALSR configuration is shown in figure 2-4.

g. ODALS. The ODALS consists of seven omnidirectional flashing lights located in the approach area of a nonprecision runway. Five lights are located on the runway centerline extended with the first light located 300 feet from the threshold and extending at equal intervals up to 1,500 feet from the threshold. The other two lights are located, one on each side of the runway threshold, at a lateral distance of 40 feet from the runway edge, or 75 feet from runway edge when installed on a runway equipped with a VASI. The ODALS configuration is shown in figure 2-5.

2-6

+100' -0'

+100' -0'

10' 10'

10' MAX

200'

1000'

1400'

2400' +100' -0'

+1' -0'10'

12 LIGHT

STATIONS @

200'±20'

SPACING

RUNWAY THRESHOLD

10'

SYMBOLS:

STEADY BURNING LIGHT, GREEN

STEADY BURNING LIGHT, WHITE

FLASHING LIGHT

RUNWAY CL

RUNWAY CL

28' 28'

-0'

FIGURE 2-4. MALSR CONFIGURATION

2-7

-0'

RUNWAY THRESHOLD

SYMBOLS:

OMNIDIRECTIONAL FLASHING LIGHT

RUNWAY CL

RUNWAY CL

5 CENTERLINE

LIGHTS @

300' ±30'

SPACING

THRESHOLD ±30'

1500'

300' 40'

EACH SIDE

OF RUNWAY

SEE NOTE

+35' -0'

+30' -0'

NOTE:

INSTALL THRESHOLD FLASHED 75' FROM EDGE OF RUNWAY

WHEN VASI IS INSTALLED ON SAME RUNWAY.

FIGURE 2-5. ODALS CONFIGURATION

2-8

201. Ideal installation. The ideal installation of an approach lighting system, which shall be accomplished whenever practicable, is accomplished when the following requirements are met:

a. Approach Light Plane. The light units in the approach light plane are in a single horizontal plane at the elevation of the runway threshold centerline. The approach light plane is 400 feet wide centered on the extended runway centerline, RAIL excepted. (See paragraph 201e for RAIL approach light plane.)

b. Clearance. No object protrudes above the approach light plane. For approach light plane clearance purposes, all roads, highways, vehicle parking areas, and railroads are considered as vertical solid objects. The clearance required above interstate highways is 17 feet; for railroads, 23 feet; and for all other roads, highways, and vehicle parking areas, 15 feet. The clearance for roads and highways is measured from the crown of the road and for railroads is measured from the top of the rails. This applies to the entire width of the approach light plane.

For vehicle parking areas, clearance is measured from the average grade in the vicinity of the highest point. Airport service roads controlled in a manner that will preclude a vehicle blocking the view of the approach lights from landing aircraft or preclude vehicle protruding above the light plane, are not considered obstructions in determining the approach light plane.

c. Location and Orientation. All light bars are installed perpendicular to the vertical plane containing the ALS centerline and are installed in their normal locations as shown in figures 2-1 through 2-4. The total overall length of all systems shall be as shown in figures 2-1 through 2-5.

d. Visibility. There is a clear line-of-sight to all lights of the system from any point on a surface, one-half degree below the ILS glide path and extending 250 feet each side of the centerline, up to 1,600 feet in advance of the outermost light in the system. For nonprecision approach systems where there is no ILS, a three degree glide path, intersecting the runway 1,000 feet from the landing threshold, is assumed for determining the visibility requirement.

e. RAIL. The ideal installation of the RAIL portion is that all sequence flashing lights be in a horizontal light plane with no obstruction penetrating the primary and secondary RAIL planes. (See Figure 2-6.)

(1) Primary Plane. The primary plane of the RAIL system begins at the last steady-burning light of the MALS portion and extends 200 feet beyond the last flashing light in the RAIL portion of the MALSR system. The primary plane has a total width of 100 feet, 50 feet each side of the runway centerline extended, and a surface that follows the plane of the RAIL System.

2-9

+0

1.

7.

.1

O

BS

TR

U

C

TI

O N

P

LA

N E

S A

T R

AI

L

S

TA

TI

O

N S

0'

P R

IM

A

R Y

0'

S E

C O

N D

A R

Y

0.

0.

7.

+0

0.

.1

0.

6.

7.

+0

.1

7.

0.

+0

2.

.1

7.

0.

+0

8.

.1

7.

0.

+0

4.

.1

0.

+0

0.

LA

S T

M A

LS

B

A R

0'

S E

C O

N D

AR

Y

+0

+0

+0

6.

+0

2.

+0

M A

X P

O S

S

LO

PE

.0

+0

4.

+0

M

AX

N

EG

S

LO

PE

-2 .5

0.

LA

S

T M

A

LS

B A

R

O B

S

TR

U C

TI

O

N P

LA

N

E S

(ID

E

A L

H O

R

IZ

O N

TA

L

R

AI

L)

0.

IS

O

M E

TR

IC

V

IE

W O

F R

A

IL

O B

S

TR

U C

TI

O

N P

LA

N

ES

FIGURE 2-6. IDEAL RAIL OBSTRUCTION CLEARANCE

2-10

(2) Secondary Plane. Beginning at the edge of the primary plane, a secondary plane having a slope of 7:1 extends outward from the edge of the primary plane for a distance of 150 feet. Both primary and secondary planes begin at the last steady-burning lights of the MALSR system and extend 200 feet beyond the last flashing light in the RAIL portion of the MALSR system. An additional secondary plane underlies the 7:1 plane, with a longitudinal slope of 50:1, beginning at the height of the last steady-burning light and extending outward (laterally) to 150 feet from the edge of the primary plane at zero gradient. The surface extends longitudinally to 200 feet beyond the last flashing light of the RAIL system. No object shall penetrate either the primary or secondary plane.

202. Permissible deviations. The deviations discussed below are siting and installation tolerances, which do not require a formal waiver request.

a. Approach Light Plane. Because of the requirement for elevated frangible lights, the lights in the threshold bar and stations 1+00 and 2+00 are considered to be at runway threshold end elevation even though they may be up to 14 inches above it. After station 2+00 the remainder of the light plane may extend from the actual centerline elevation of the lamp at station 2+00 or revert to the centerline threshold runway elevation extended to station 2+00. If a single horizontal light plane is not possible because of terrain or solid objects within its area, the plane may be raised if considered more economical than lowering, removing, or displacing interfering objects. Other variations of light assembly designs above the light plane are acceptable only where so designated on standard drawings. The light plane may also be lowered where sharply descending terrain makes it economically necessary.

(1) Slope Gradient. The slope gradient shall be kept as small as possible and shall not exceed two percent for a positive slope nor one percent for a negative slope (RAIL excepted, paragraph 202a(5)). The sloping segment may start no closer than 200 feet from the landing threshold. Where the threshold is established at the approach end or is displaced less than 200 feet, the slope gradient shall start at runway approach end elevation. Where the landing threshold is displaced greater than 200 feet from the runway approach end, the slope gradient shall start 200 feet from the displaced threshold at the elevation of the runway surface at the 200 feet point. The sloping segment begins and ends at a light station.

(2) ALSF-2 Sloping Segment. Only one sloping segment is permitted in a system.

The sloping segment shall contain a minimum of four light bars or 300 feet. The sloping segment may extend to the end of the system or may revert into a horizontal segment of at least three light bar stations (200 feet). Negative slope is not permitted in the inner 1,500 feet.

(3) MALS and ODALS Sloping Segments. A sloping or horizontal segment shall contain at least three consecutive light bar stations. Only one positive sloping segment is permitted in a system. The sloping segment may start at the first light bar and extend to the end of the system, or may be preceded by a horizontal segment or followed by either a horizontal or negative sloping segment. For ODALS, the sloping segment may start at 200 feet from the threshold or at a height of 24 inches above the threshold elevation beginning at the first light on centerline (station 3+00).

2-11

(4) Semiflush Lights. In determining the approach light plane, all semiflush lights installed in pavement with sloping gradient are considered as being in a horizontal plane at the elevation of the outermost semiflush light station on the ALS centerline at the approach end of system.

(5) RAIL Slope Gradient. The primary plane may have a maximum permissible slope of two and one-half percent negative (see figure 2-8) and two percent positive (see figure 2-7). The primary plane may also have one change of gradient (see figure 2-9). A sloping or horizontal segment shall contain at least three consecutive light stations.

b. Clearance.

(l) Where necessary to ensure an acceptable level of performance of an instrument landing system (ILS), antennas and their associated supports for the marker beacon and/or localizer may on a category I approach penetrate the approach light plane. These antennas, or their supports, shall not, however, obscure any light of the approach lighting system. This exception applies only to penetration of the approach light plane and in no way refers to the ILS or non-ILS approach surfaces as defined in Terminal Instrument Procedure (TERPS) or Part 77 of the Federal Aviation Regulations (FAR). Penetration of the 50:1 surface or the approach light plane is prohibited for category II/III approach lighting systems.

(2) Since the approach light plane passes through the beam centers of the lights, a portion of the light unit and support hardware will, of necessity, penetrate the light plane. For example, this condition exists when the ALSF-2 is operated as a SSALR.

(3) When an ILS marker is located within the approach light system, the approach light plane shall be set so that the marker shelter is below the light plane.

2-12

O

BS

TR

U

C

TI

O N

P

LA

N

ES

A T

R A

IL

S

TA

TI

O N

S

0'

P R

IM

A

R Y

0'

S E

C O

N D

A R

Y

.1

0.

+0

LA

S

T M

A

LS

B A

R

0'

S

EC

O N

D

AR

Y

+0

+0

+0

6.

+0

2.

+0

+0

4.

+0

0.

LA

S

T M

AL

S

BA

R

R

AI

L P

R O

FI

LE

(M A

X

IM

U M

P O

S

IT

IV

E

S

LO

PE

2%

0.

IS

O

M E

TR

IC

V

IE

W O

F A

T R

A

IL

S

TA

TI

O

N S

+2 .0

S

LO

PE

8.

4.

.1

4.

+0

.1

8.

+0

.1

2.

+0

.1

6.

+0

.1

0.

+0

.1

4.

+0

FIGURE 2-7. RAIL OBSTRUCTION CLEARANCE FOR +2.0% SLOPE

2-13

IS

O

M E

TR

IC

V

IE

W O

F R

A

IL

O B

S

TR

U C

TI

O

N P

LA

N

E S

.1

+0

+0

+0

.0

+0

.0

+0

+0

.0

+0

LA

S T

M

AL

S

BA

R

.0

.0

.0

0.

+0

.5

7.

1 O

BS

TR

U C

TI

O

N P

LA

N

ES

A

T R

A

IL

S

TA

TI

O

N S

0'

P R

IM

AR

Y

0'

SE

C O

N D

AR

Y

.0

.5

7.

+0

.0

.0

1.

7.

+0

7.

.0

+0

6.

.1

7.

.0

+0

8.

7.

.0

+0

4.

.1

0.

+0

LA

S

T M

A

LS

B

AR

0'

S

EC

O N

D

AR

Y

R A

IL

P

R O

FI

LE

(M A

XI

M

U M

N

EG

AT

IV

E S

LO

PE

2.

5%

FIGURE 2-8. RAIL OBSTRUCTION CLEARANCE FOR -2.5% SLOPE

2-14

+0

+0

LA

ST

M A

LS

BA

R

.0

+0

+0

+0

+0

4.

1.

.0

.0

.0

.0

M

AX

P O

S S

LO

PE

.0

M

AX

N

EG

S

LO

PE

-2

.5

-2 .0

+1

.5 % R A

IL

P

R O

FI

LE

(T W

O S

LO

P

IN

G

S

EG

M E

N

TS

-2

.0

A N

D

1.

5%

IS

O

M E

TR

IC

V

IE

W O

F R

AI

L

O B

S

TR

U C

TI

O

N P

LA

N

E S

4.

7:

4.

+0

:1

7:

0.

1.

+0

+0

+0

+0

+0

+0

:1

7:

6.

.0

:1

7:

.5

.0

:1

7:

.5

.0

:1

7:

.5

.0

:1

.5

0.

LA

S T

M A

LS

B

AR

0'

P R

IM

A

R Y

O

BS

TR

U

C

TI

O N

P

LA

N

ES

A T

R A

IL

S

TA

TI

O N

S

0'

S E

C O

N D

A R

Y

0' S

EC

O

N D

A R

Y

+0

0.

.0

0.

FIGURE 2-9. TYPICAL RAIL OBSTRUCTION CLEARANCE FOR TWO SLOPING

SEGMENTS

2-15

c. Location and Orientation.

(1) The position of light bars along the centerline may be adjusted, where necessary, to avoid roads, buildings, railroads, etc. Where a light bar must be displaced longitudinally from its normal position, the adjacent light bars should, where practicable, be displaced by appropriate amounts in order to maintain essentially equal longitudinal spacing.

(2) The threshold lights for the approach lighting system should be located as close to the landing threshold as possible but may, in order to avoid conflict with the existing runway lights, be displaced in front of the landing threshold a maximum of l0 feet. The threshold lights shall not obstruct the existing runway lights or vice-versa. The threshold lights may be installed to follow the transverse slope of the runway.

(3) Because of the physical arrangement and mounting problems associated with the sequenced flasher installed with steady-burning lights, the sequenced flasher light beam centers may be located up to a maximum distance of four feet below the approach light plane established by the beam centers of the steady-burning lights. The sequenced flasher light unit may be located a maximum of five feet along the ALS centerline into the approach from the steady-burning light bar.

(4) While the light support structures for light heights from six feet to 40 feet are normally sited to be lowered parallel to the ALS centerline, they may be aligned to be lowered at an angle to the ALS centerline to accommodate site-peculiar conditions.

d. Light Station Tolerances. The light station tolerances are as follows:

(l) Lateral (perpendicular to ALS centerline) - ± 3 inches.

(2) Distance between individual lights on a light bar - ± 1 inch.

(3) Mounting height.

(a) Up to six feet - ± 1 inch.

(b) Over six feet to 40 feet - ± 2 inches.

(c) Over 40 feet - ± 3 inches.

(4) All lights on a bar in a line perpendicular to the ALS centerline - ± 1 inch.

(5) Light unit vertical angular alignment - ± 1 degree.

(6) Light unit horizontal angular alignment - ± 5 degrees.

(7) Distance between stations:

2-16

(a) On 100 feet stationing, tolerance is 100 ± 10 feet.

(b) On 200 feet stationing, tolerance is 200 ± 20 feet.

(c) On 300 feet stationing, tolerance is 300 ± 30 feet.

(8) Longitudinal deviation from installation station designation (along ALS centerline)

- ± 6 inches.

(9) ODALS threshold flashing lights shall be installed at runway centerline threshold elevation, + 1 foot to - 5 feet.

e. System Length. The system length shall be 3,000 feet when the ILS glide slope is less than 2.75 degrees.

203. Use of Various Types of Lights.

a. Semiflush Lights. Semiflush lights shall be used only in displaced threshold areas or in overrun areas at military-civil, joint-use airports when required by the military.

b. Frangible Lights. Frangible lights shall be used at light bar stations having a ground level to approach light plane height of six feet or less.

c. Low-Impact Resistant Lights. Low-impact resistant lights shall be used at light bar stations having a ground level to approach light plane height greater than six feet but 40 feet or less.

d. Semifrangible Lights. Semifrangible lights shall be used at light bar stations having a ground level to approach light plane height greater than 40 feet.

e. Rigid Lights. Rigid lights shall not be installed in any new approach lighting systems.

204. Lighting Fixtures.

a. High Intensity Systems.

(1) Specification FAA-E-2408b, 300-watt, 20A, PAR-56 lamps for steady-burning, aboveground, white lights with Specification FAA-E-982 lampholder.

(2) Specification FAA-E-2408b, 500-watt, 20A, PAR-56 lamps for steady-burning, aboveground, colored lights with Specification FAA-E-982 lampholder.

(3) Specifications FAA-E-2952 or FAA-E-2491 approach lights, 500-watt, for all semiflush lights.

(4) Specifications FAA-E-2628b or FAA-E-2689a for all sequenced flashers.

2-17

b. Medium Intensity Systems.

(1) 120-watt, 120V, PAR-38, spot lamps, General Electric wattmiser or equal steady-burning lights (except threshold). Osram 14856, 120-watt, 120V, PAR-38; General Electric 26371, 150-Watt, 120V, PAR-38 spot lamps, or equal, for above ground steady-burning lights (except threshold).

(2) Specification L-850-B (Advisory Circular 150/5345-46), 200-watt, semiflush light units, unidirectional (except threshold). Specification FAA-E-2968, Steady Burning, Semiflush Approach Light units for Medium Intensity Approach Lighting System with Runway Alignment Indicator lights (MALSR).

(3) Specifications FAA-E-2325e, FAA-E-2980, and FAA-E-2628b, sequenced flashers.

(4) Specification L-850-E (Advisory Circular 150/5345-46), 200-watt, semiflush light units, unidirectional, with green filter. Specification (FAA-E-2891, Steady Burning, Semiflush Threshold Approach Light Assembly of the Medium Intensity Approach Lighting System with Runway Alignment Indicator lights (MALSR).

(5) 300-watt, 120V, PAR-56 lamps for steady-burning, above ground green lights for threshold with Specification FAA-E-982J lampholder.

c. ODALS. Specification FAA-E-2651, Omnidirectional flashing light.

205. Control and Monitoring Requirements.

a. Control Requirements. Remote control shall be provided for all approach lighting systems defined in paragraph 200. The remote control link may be either landlines or radio, except for ALSF-2. The ALSF-2 shall have landline control. The remote control head has an indicating panel that indicates the last selection for each particular system. Sequenced flashers are on only when the steady-burning lights are on. Radio control requirements are contained in Appendix B and Advisory Circular AC 150/5345-49, Specification L-854, Radio Control Equipment.

b. Operational Monitoring Requirements. Monitoring is required on all brightness steps for all approach lighting systems that support category II and IIIa instrument approach procedures. Monitoring is not required for category I approach lighting systems. The monitoring equipment shall provide an indication of whether power is being delivered to the lamps when the system is energized.

c. Remote Maintenance Monitoring Requirements. Remote maintenance monitoring is required for maintenance purposes. The ALSF-2 remote maintenance monitoring shall monitor the system the same on all five brightness steps.

2-18

206. Vertical Alignment. All lights, except semiflush lights, shall be aimed vertically.

Semiflush lights have a preset vertical angle and do not require vertical aiming. All steady-burning lights in a bar shall be aimed at the same vertical angle. All sequenced flashers shall be aimed at six degrees in all circumstances.

a. ALSF-2 Vertical Alignment. The ALSF-2 steady-burning lights are vertically aligned using a visual segment modified method that establishes the alignment as listed in table 2-1. The angular settings in table 2-1 are empirically determined for a three degree glide slope. The angular settings in table 2-1 provide for optimum use of the 12 degree vertical beam spread of the Q20A/PAR-56 approach light lamps and provides a smooth transition between the category I and the category II angular elevation settings.

b. MALS Vertical Alignment. The MALS steady-burning lights are vertically aligned using the VS-400 visual segment method that establishes the alignment as listed in table 2-2.

The angular settings in table 2-2 are empirically determined for a three degree glide slope. The angular settings in table 2-2 are established for the PAR-38 spot lamp.

c. Corrections for Permissible Deviations. The elevation angles of the steady-burning lights shall be shifted by the amount that the glide slope is shifted from three degrees. The correction for vertical alignment due to displacement of lights above and below the horizontal plane through the threshold shall be calculated using the equation shown in figure 2-10.

However, on the ALSF-2 no lamp elevation setting shall be greater than nine degrees or less than six degrees. No correction of vertical alignment is necessary for light stations installed within the stationing tolerance listed in paragraph 202d.(7). Add 0.1 degree to the angular siting of the light for each 200 feet the touchdown point is moved away from the threshold from the normal 1,000-foot touchdown point; subtract 0.1 degree when the glide slope touchdown point is moved 200 feet toward the threshold from a 1,000-foot touchdown point.

207. Horizontal Alignment. All lights shall be aligned with their beam axis parallel to the extended runway centerline.

208. Penetration of Approach Surface. With the exception of the frangible lights at stations 0+00, 1+00, and 2+00, no other component of an approach lighting system may penetrate the ILS or non-ILS approach surface detailed for civil use in TERPS or Part 77 of the Federal Aviation Regulations.

2-19

TABLE 2-1. Elevation-Setting Angles for Q20A/PAR56 Approach Lighting Lamps (ALSF-2)

Station Setting Angle (Degrees)

Station Setting Angle (Degrees)

3000 8.0 1400 7.0 2900 7.9 1300 6.9 2800 7.9 1200 6.9 2700 7.8 1100 6.8 2600 7.7 1000 6.7 2500 7.7 900 6.7 2400 7.6 800 6.6 2300 7.6 700 6.5 2200 7.5 600 6.5 2100 7.4 500 6.4 2000 7.4 400 6.3 1900 7.3 300 6.3 1800 7.2 200 6.2 1700 7.2 100 6.2 1600 7.1 0 6.1 1500 7.0

TABLE 2-2. Elevation-Setting Angles for 150PAR38/SP Approach Light Lamps (MALS)

Station Setting Angle (Degrees)

0 3.1 200 3.2 400 3.3 600 3.4 800 3.4 1000 3.5 1200 3.6 1400 3.7

2-20

RUNWAY

GLIDE SLOPE

LIGHT

THRESHOLD

HORIZONTAL PLANE

LIGHT ABOVE THE HORIZONTAL PLANE b = a - Arctan (h/d)

LIGHT BELOW THE HORIZONTAL PLANE b = a + Arctan (h/d)

THE ELEVATION SETTING ANGLE FOR THE PARTICULAR STATION TAKEN FROM

FROM TABLE 2-1 FOR ALSF-2 AND TABLE 2-2 FOR MALS.

CORRECTED ELEVATION SETTING ANGLE.

DESIGNATED DISTANCE: BEING 4732 FEET FOR MALS AND 1246 FOR ALSF-2.

HEIGHT OF THE LIGHT ABOVE THE HORIZONTAL PLANE PASSING THROUGH THE

THRESHOLD.

a:

b:

d:

h:

LEGEND

FOR ALSF-2 THE ANGLE b SHALL BE ALWAYS 6° OR MORE AND 9° OR LESS.

NOTE:

d h b a

FIGURE 2-10. CORRECTION OF ELEVATION-SETTING ANGLE FOR APPROACH

LIGHTS DISPLACED FROM THE HORIZONTAL PLANE PASSING THROUGH THE

THRESHOLD

2-21

209. MISCELLANEOUS PROVISIONS.

a. Location of Power Equipment. The ALSF-2 substation and the power and control station for the MALS (also MALSF and MALSR) and ODALS shall be located no closer than 400 feet to the ALS centerline. The location shall also be such that cable and trenching costs are held to a minimum provided the location chosen minimizes disturbance to the ILS radiated signal and does not constitute an obstruction as defined in the Federal Aviation Regulations. The MALS, MALSF, MALSR, and ODALS power and control equipment are permitted indoor installation (1) where a storage shed is included in the project or (2) where space is available in an adjacent facility and installation can be made without interference with maintenance and without impacting space intended for future facility expansion.

b. Access. A suitable access road, footpath, or catwalk shall be provided for servicing all component parts of an approach lighting system. An access road is provided to the power and control equipment station. Existing access roads should be utilized as much as possible.

Catwalks should be employed only when the individual supports exceed 100 feet in height or when the area through which the approach lighting system passes is completely inaccessible to foot or vehicular traffic. Access roads, where required, should meet the minimum requirements of the latest edition of Order 6940.2, Access Road Cross Sections and Typical Drawing Details for FAA Facilities.

c. Storage Shed. A suitable storage shed should be provided if there are no existing facilities adequate for this purpose. Only one storage shed per airport should be provided.

d. Pier or Other Rigid Structure Installation. Where an approach lighting system is installed on a pier or other rigid structure, a minimum of 20 feet shall be provided between the light plane and the rigid structure. In order to maintain the 20-foot separation, lights shall conform to paragraph 203c, Low-Impact Resistant Lights. When the 20-foot separation between the light plane and the pier or rigid structure cannot be maintained, a National Air Space (NAS) Change Proposal is required.

210. Brightness Steps. The number of brightness steps and approximate relative intensities for each system is shown in table 2-3.

211. Displaced Threshold Lighting. When approach lighting systems are installed in a displaced threshold area having centerline lighting the control of the two separate systems shall conform to the latest edition of Advisory Circular AC 150/5340-30, Design and Installation Details for Airport Visual Aids, Installation Details for Runway Centerline and Touchdown Zone Lighting Systems.

212. Floodplain Low-Impact Resistance (LIR) Installation. See Appendix D.

2-22

2-23

TABLE 2-3. Brightness Steps

Steady-Burning Lights Flashing Lights System No. Steps % Relative Intensity No. Steps % Relative Intensity

ALSF-2 5 100–20–4-0.8-0.16a 3 100-20-2.3

MALS 2c 100-4 - -

MALSF 2c 100-4 2c 100-8

MALSR 3 100-20-4 3 100-(26 and 8)b-1

MALSF 3 100-20-4 3 100-10-2.3

ODALS - - 3 100-30-1.4

a. The ALSF-2 has a subsystem SSALR, both configurations have five brightness steps.

On steady-burning light intensity steps four and five,…