UNIFORM SPECIFICATIONS - NEW CONTRACT-5-28-09.doc

ATTACHMENT J.3 – Specifications Male and Female specification documents for the following uniform items follow this cover sheet. Some uniform items have multiple specs for female and male personnel and the trousers have relaxed and regular fit specifications.

Unisex Items Unisex Socks TSA Unisex belt TSA Nameplate TSA Shoulder Board—Officer—Navy TSA Shoulder Board—Lead Officer—Navy TSA Shoulder Board—Supervisor—Navy TSA Unisex Sweater Vest TSA Unisex Polo Shirt ………………………………………………………… 11 Unisex Commando Sweater Unisex Team Jacket Unisex 3 Season Waist Length Jacket Unisex Hip Length Parka Knit Stocking Cap TSA Ball Cap……………………………………………………………………………..28 TSA Unisex, clip-on ties Men’s TSA Men's Long Sleeve Shirt TSA Men's Short Sleeve Shirt TSA Male Relaxed Fit Trouser TSA Male Regular Fit Trouser Male Shorts TSA Men's 100% Cotton Long Sleeve Shirt …………………….…………….44 TSA Men's 100% Cotton Short Sleeve Shirt ………………….…………… TSA Male 100% Cotton Trouser ………………………………….…………….50 Male Shoe ……………………………………………..………………………….....…..53 Female Uniform Items

TSA Women's Long Sleeve Shirt ………………………………………….....…55 TSA Women's Short Sleeve Shirt ………………………………………….…...58 TSA Women’s Relaxed Fit Trouser ………………………………………… TSA Women’s Regular Fit Trouser ………………………………………… Female Shorts ……………………………………………………………………..67 TSA Women’s Crossover Tie ………………………………………………..….70 Female Shoe …………………………………………………………………… TSA Women's 100% Cotton Long Sleeve Shirt ……………………………...72 TSA Women's 100% Cotton Short Sleeve Shirt ………………………….….75 TSA Women’s 100% Cotton Trouser ……………………………………… Women’s Long Skirt ……………………………………………………………...81 TSA Women's Short Sleeve Maternity Shirt ………………………………….82 TSA Women's Long Sleeve Maternity Shirt…………………………………..85 Female Maternity Trouser ………………………………………………………88 Baggage TSO Items

Unisex Unlined Coverall ………………………………………………………...91 Unisex Insulated Coverall ……………………………………………………….94 Embroidered Shoulder Emblems………………………………………………97 TSA Badge Emblem …………………………………………………………… Other Potential Uniform Items …………………………………………………98

NON TSO ITEMS

TSI Polo Shirts …………………………………………………………………...99 TSI Lightweight Jacket ………………………………………………………...103 TSI Parka (3 in 1) ………………………………………………………………..104

TRANSPORTATION SECURITY ADMINISTRATION

SCREENERS’UNIFORM

Unisex Socks Style:

Crew Sock – Thorlo style # WGX-13 or equal

Color:

Black

Fiber Content

85% acrylic, 12% stretch nylon, 3% spandex

Finished Layouts:

Top Width

3.25 inches

Top Length

7.00 inches

Leg Length

11.00 inches

Foot Length

10.25 inches

Finishes Stretches:

Top Cross

9.00 inches

Foot Cross

8.00 inches

Footstretch

17.00 inches

Fits Male Shoe Sizes

8.5 to 12.5 Fits Female Shoe Sizes 5 to 10

TRANSPORTATION SECURITY ADMINISTRATION

TSA Unisex belt

Style:

Unlined lux finish drum-dyed black leather belt with embossed lines and satin silver buckle

Components:

Fabric:

Black leather

Buckle:

Satin nickel plating

Belt Holes:

First hole is 3” from the tip with 1” graduations between each hole.

Belt Width:

1 ½”

Loop Width:

½”

TRANSPORTATION SECURITY ADMINISTRATION

TSA Nameplate

DESIGN

Brushed silver finished name plate will be 2-13/16” by 7/8” in size with no border. It will have a double clutch back.

ENGRAVING

The name pin will have two lines of engraving. The first line will be the officer’s last name. The second line will be officer’s title.

TRANSPORTATION SECURITY ADMINISTRATION

TSA Shoulder Board—Officer—Navy

FABRIC

Fabric shall be the same fabric as used for the TSA trousers.

DESIGN

The shoulder board shall be designed to fit over the shirt epaulets. It shall designate the rank of Officer.

CONSTRUCTION

The shoulder board shall taper, measuring 2 ¼” at the armhole end and 1 7/8” at the button end. It shall measure 3 ½” in total length. It shall be fused with Pellon for reinforcement. The loop shall be closed with a ¼” seam, single needle lock stitched. The ends of the shoulder board shall be turned under ¼” and edge-stitched (to finish).

EMBROIDERY

· “TSA” shall be embroidered in block letters on the topside of the shoulder board. The top edge of the letters shall begin 1 3/8” below the narrow edge (1 7/8” wide edge) of the shoulder board. The letters shall be ¾” tall. The color of the embroidery shall be metallic silver color MS51001. The total width of the embroidery shall measure 1 ⅝” wide.

· There shall be one metallic silver bar embroidered on the narrower end of the shoulder board (1 7/8” wide edge). It shall be placed ¼” off the edge. There shall be one metallic silver bar embroidered on the wider end of the shoulder board (2 ¼” wide edge). It shall be placed ¼” off the edge. Each bar shall be 1/8” wide. The color of the bars shall be metallic silver color MS51001.

SIZES

One Size Fits All

TRANSPORTATION SECURITY ADMINISTRATION

TSA Shoulder Board—Lead Officer—Navy

FABRIC

Fabric shall be the same fabric as used for the TSA trousers.

DESIGN

The shoulder board shall be designed to fit over the shirt epaulets. It shall designate the rank of Lead Officer.

CONSTRUCTION

The shoulder board shall taper, measuring 2 ¼” at the armhole end and 1 7/8” at the button end. It shall measure 3 ½” in total length. It shall be fused with Pellon for reinforcement. The loop shall be closed with a ¼” seam, single needle lock stitched. The ends of the shoulder board shall be turned under ¼” and edge-stitched (to finish).

EMBROIDERY

· “TSA” shall be embroidered in block letters on the topside of the shoulder board. The top edge of the letters shall begin 1 3/8” below the narrow edge (1 7/8” wide edge) of the shoulder board. The letters shall be ¾” tall. The color of the embroidery shall be metallic silver, color MS51001. The total width of the embroidery shall measure 1 ⅝” wide.

· There shall be one silver metallic bar embroidered on the narrower end of the shoulder board (1 7/8” wide edge). It shall be placed ¼” off the edge. There shall be two metallic silver bars embroidered on the wider end of the shoulder board (2 ¼” wide edge). The outermost bar shall be placed ¼” off the edge. The second bar shall be placed 1/8” from the outermost bar. Each bar shall be 1/8” wide. The color of the bars shall be silver metallic color MS51001.

SIZES

One Size Fits All

TRANSPORTATION SECURITY ADMINISTRATION

TSA Shoulder Board—Supervisor—Navy

FABRIC

Fabric shall be the same fabric as used for the TSA trousers.

DESIGN

The shoulder board shall be designed to fit over the shirt epaulets. It shall designate the rank of Supervisory Officer.

CONSTRUCTION

The shoulder board shall taper, measuring 2 ¼” at the armhole end and 1 7/8” at the button end. It shall measure 3 ½” in total length. It shall be fused with Pellon for reinforcement. The loop shall be closed with a ¼” seam, single needle lock stitched. The ends of the shoulder board shall be turned under ¼” and edge-stitched (to finish).

EMBROIDERY

· “TSA” shall be embroidered in block letters on the topside of the shoulder board. The top edge of the letters shall begin 1 3/8” below the narrow edge (1 7/8” wide edge) of the shoulder board. The letters shall be ¾” tall. The color of the embroidery shall be metallic silver color MS51001. The total width of the embroidery shall measure 1 ⅝” wide.

· There shall be one metallic silver bar embroidered on the narrower end of the shoulder board (1 7/8” wide edge). It shall be placed ¼” off the edge. There shall be three metallic silver bars embroidered on the wider end of the shoulder board (2 ¼” wide edge). The outermost bar shall be placed ¼” off the edge. The second bar shall be placed 1/8” from the outermost bar. The third bar shall be placed 1/8” from the second bar. Each bar shall be 1/8” wide. The color of the bars shall be metallic silver color MS51001.

SIZES

One Size Fits All

Transportation Security Administration

TSA Unisex Sweater Vest

FABRIC

The sweater yarn shall be 100% Acrylic with Pil-Trol®. The Pil-Trol® finish protects against pilling and assists in retention of the garment’s shape.

Fabric used for epaulets, nameplate holder, and badge tab shall be 65% Polyester / 35% Cotton, the same as the pant fabric.

COLOR

The yarn and patch fabric shall be Navy blue.

DESIGN

The sweater shall be a V-neck commando style, sweater vest. There shall be durable fabric patches on the shoulders. The sweater shall have functional epaulets, a nameplate holder, and a badge tab.

NECK

The neck shall be finished with a 1” wide, 1 X 1 rib stitch trim. Right and left neck trims shall be joined at center front to for a “V” that has a “chevron” appearance.

BOTTOM BAND

The bottom band shall be full fashion style, tapering to the hem. The band shall be ribbed and shall have elastic cord in the bottom edge to support shape retention.

ARMHOLES

The armholes shall be finished with a 1” wide, 1 X 1 rib stitch trim.

TRANSPORTATION SECURITY ADMINISTRATION

TSA Unisex Polo Shirt

FABRIC

Fabric is 50% cotton and 50% polyester mesh knit (herringbone pattern).

COLOR:

Royal Blue

DESIGN AND CONSTRUCTION

Short sleeve knit polo shirt; rib knit collar and sleeve welts, topstitched shoulder seams, clean finished placket, three wood grain button closure, and straight tail.

COLLAR

Contrast rib knit collar with ¼” tip

SLEEVES

One piece sleeve

Contrast rib knit cuffs with ¼” tip

FRONT

Three button front with top horizontal buttonhole and the other two are vertical

1 ½” wide x 6 ½” long clean finished placket with horizontal bar at placket bottom.

BACK

One piece back

HEM

Straight tail

Bottom hem ¾” blind stitch

SEAMING

Side seams are serged and clean finished. Bottom hem is blind serged.

EMBLEMS

· TSA emblem will be stitched to the right upper sleeve, centered 1 ½” below the sleeve set seam.

· 9-11 Team Spirit emblem will be stitched to the left upper sleeve, centered 1 ½” below the sleeve set seam.

· Badge emblem on left upper front

TRANSPORTATION SECURITY ADMINISTRATION

Unisex Commando Sweater

FABRIC:

Fabric is made of 100% DuraPil™ Acrylic

COLOR:

Dark Navy

DESIGN:

Sweater is a rib knit, has long sleeves, V-neck, shoulder patches with epaulets and elbow patches

NECK:

V-neck has rib knit band

BOTTOM BAND:

Bottom band has fashion style tapering to bottom

SLEEVES:

Sleeves have polycotton patches at elbows in dark navy with rib knit cuffs

CLOTH PATCHES:

Shoulder patches are polycotton in dark navy

EPAULETS:

Epaulets are dark navy polycotton and attach to the shoulder patches with Velcro.

NAME PLATE AND BADGE TAB:

Name plate and badge tab are dark navy polycotton and are located on the upper left (badge tab) and upper right (nameplate) front of the sweater.

EMBLEMS:

· TSA shoulder emblem shall be sewn on the right upper sleeve 1 ½” below the sleeve set seam and centered with the sleeve set seam.

· The 9-11 Team Spirit emblem shall be sewn on the left upper sleeve 1 ½” below the sleeve set seam and centered with the sleeve set seam.

Transportation Security Administration

Screener Uniform Specification

Unisex Team Jacket

FABRIC

The body fabric shall be 65% Polyester / 35% Cotton, 2 X 1 twill, 7.5 ounces per square yard. It shall have a durable press finish and shall be vat thermosal dyed. The color shall be navy.

The lining shall be nylon quilted to 3.3 ounces per square yard 100% nylon taffeta lining, with a ⅛” foam insulation. The color shall be black.

DEISGN

The jacket style shall be a zip front baseball style jacket. It shall have a rib collar, sleeve cuffs, and bottom band. There shall be welted slash pockets on the front. There shall be a pencil pocket on the left sleeve.

CONSTRUCTION

The lining shall be permanently sewn into the jacket and shall be clean finished at the front zipper edge. The collar, bottom band, and cuffs shall be clean finished to the lining.

COLLAR

The collar shall be a one-piece knit collar. It shall be clean finished between the body and lining fabric. The collar shall measure 1 ¾” tall at center back.

ZIPPER

The front of the jacket shall have a separating brass zipper. The zipper shall be attached to the jacket with a double needle topstitch, stitched at a 3/16” margin. The bottom of the zipper shall be reinforced with bartacks, one on each side.

POCKETS

The front of the jacket shall have a diagonal, two-piece, slash style pocket on each panel. The pocket bag shall be safety stitched. The pocket opening shall be finished with a ⅝” wide welt. The welt opening shall be edge-stitched around all four edges. It shall be reinforced with bartacks at each end. The pocket opening shall measure 6 ¼” wide. The pocket bag shall be 8 ½” deep.

There shall be a pencil pocket located on the left sleeve, 6 ¼” below the sleeve set seam. The pocket shall measure 3 ½” wide by 4 ¾” deep. The pocket shall be set to the sleeve with an edge-stitch. The upper edge of the pocket shall be finished with a ½” double turned hem, single needle topstitched at a ⅜” margin. The pocket shall be reinforced with bartacks at each upper corner.

EMBLEMS

· TSA shoulder emblems shall be sewn on each sleeve. They shall be placed 1 ½” below the sleeve set seam. This jacket does not have epaulets (Per the Solicitation Amendment dated 12/11/03).

· A TSA badge emblem shall be sewn on the left chest. The inner edge of the badge emblem (edge closest to center front) shall be placed 3 ½” from center front. The top edge of the badge emblem shall be placed 5” from the high point of the shoulder.

SIZES

Available Sizes:

S, M, L, XL, 2XL, 3XL, 4XL, 5XL, 6XL

DIMENSION SPECIFICATIONS

**Note—Short sleeve lengths shall be 1 ½” shorter than regular sleeve lengths; Long sleeve lengths shall be 1 ½” longer than regular sleeve lengths; X-Long sleeve lengths shall be 3” longer than regular sleeve lengths.

Transportation Security Administration Screener Uniform Specification

TSA Unisex 3 Season Waist Length Jacket with Liner

FABRIC

Outershell:

Weft 140 denier 102 filament two ply

Permanent Lining:

Zip Out Liner:

The jacket shall be new Generation 3® a full cut, waist length model with two-way zipper front, Primaloft( zip-in/zip-out liner, shirred waistband, and zippered side vents. Coat construction with sealed seams shall be used throughout with body and sleeves being fully lined.

BODY DETAIL

The front shall be plain with box pleated patch pockets, flaps and badge tab. The inside facings shall be made of outer fabric and are to be sewn on top of the nylon lining which extends to the front edge of the jacket. There is to be a separate 2½” shirred waistband with 2½” heavy duty elastic. The entire waistband is to be shirred with the exception of an area 5½” on either side of the front opening. There shall be side zipper entry on both side seams, approximately 11” in length and secured by a nylon zipper and snap closure. The shoulders shall have pads. There shall be a 1½” wide inside storm flap from the bottom of the collar to the bottom of the waistband on the right front to maintain windproof quality. There shall be three drop down panel access pockets; one located on each of the fronts and one located on the back of the jacket. There shall be a zipper track located at the center middle back and concealed in a zipper garage for an optional hood.

INSIDE DETAIL

There shall be a welted pocket on left side of the jacket (inside). The pocket opening shall be 4 ½” wide and a minimum of 6” deep. It shall be constructed from lining fabric. Bartacks shall reinforce the opening. There shall be two cut‑in pockets on the left and right sides measuring approximately 5¼” wide and 6" deep. There shall be a strap and snap on the lining of each sleeve end for attaching the zip-in liner.

SLEEVES

The sleeves shall be one piece set in with a single needle machine. The bottom of the sleeve shall have hook and loop as well as elastic for adjustable fit. A small strap and snap feature shall be sewn to the lower lining area of each sleeve for attaching the zip-in liner.

POCKETS

There shall be two patch pockets with box pleats, finishing approximately 6¼” wide and 7½” deep. Flaps shall be scalloped and self lined. They shall close with hook and loop on the side points and with a centered buttonhole. The pockets shall be self-lined with an opening of approximately 5½” on the side. The left patch pocket is to have a pencil opening at the top of the flap. Both the pockets and the flaps are to be bartacked.

COLLAR

The stand-up collar shall be made using self material. It shall be interlined with Pellon.

EPAULETS

The epaulets shall be made of 2 layers of body fabric (stitched, turned, and ¼” topstitched) and shall be interlined. They shall be sewn into the sleeve head seam. They shall be "X" stitched at the armhole end and tacked to the jacket at the neck edge. The epaulets shall measure 2 ¼” wide at the armhole end and 1 ¾” wide at the pointed end. Epaulets shall have keyhole buttonholes, with a drilled eyelet, located ¾” from the pointed tip of the epaulet. (The buttonholes shall be centered on the epaulet and run parallel with the long edges of the epaulet.) There shall be a 24 Ligne, flat metal shank button inserted into each drilled eyelet and attached on the underside with an O-ring.

BADGE TAB

The badge tab shall be made of the outer fabric and lined with pocketing being 2” tall by 1” wide. The first eyelet is 1/2” down from the top of the finished edge and the second is 1/2” up from the bottom finished edge. The eyelets are spaced 1” from center to center. It shall be centered 2-1/2” above the left pocket flap.

ZIPPER

There shall be a YKK #5, two-way molded nylon zipper in the front, an 11” nylon zipper on each side vent, and a zipper at the center back neck.

BUTTONS AND SNAPS

The pocket flaps and epaulets shall be secured with 24 ligne metal buttons. Flaps and epaulets shall close with 24 ligne metal buttons. Front fly shall be secured by high impact, non-reflective, non-glare, scratch resistant snaps.

THREAD

All sewing is to be done with polyester core thread or 100% spun polyester thread.

SIZE TAG AND CARE INSTRUCTIONS

Each jacket shall have a sewn in woven size label. There shall also be a printed label with care instructions and each coat marked with lot number, size, fiber content and WPL number.

EMBLEMS

· TSA emblem shall be attached to the right upper sleeve 1 ½” below the sleeve set seam and centered with the epaulet.

· 9-11 Team Spirit emblem shall be attached to the left upper sleeve 1 ½” below the sleeve set seam and centered with the epaulet.

· Large TSA lettered emblem shall be attached to the back 1” below the center back zipper flap.

ZIP IN / ZIP OUT LINER

DESIGN

The liner shall be modeled from a full-cut, long-sleeve liner pattern.

BODY DETAIL

The liner shall have long sleeves and knit wristlets with an anchor loop to accept buttons for attaching the liner to the outer jacket. The edges of the entire body shall be bound with 1‑9/16" nylon bias binding. The side seams, shoulders, and sleeve seams shall be joined with a safety-stitch. The back armholes shall have knit inserts to allow freedom of movement (creating a mock-action back).

POCKET

There shall be one patch pocket located on the lower right of the inside. The pocket shall be bound with nylon bias binding and attached with a single-needle stitch.

ZIPPER

There shall be a molded nylon zipper attached to the liner. This zipper shall correspond with an equal length zipper located on the inside of the outer jacket (used for zipping the liner into the outer jacket).

THREAD

All seams shall be sewn with polyester core thread or 100% spun polyester thread.

SIZE TAG AND CARE INSTRUCTIONS

The liner shall have a sewn‑in label that contains care instructions, style number, fiber content, size, WPL, and county of origin located on the center back below the neck edge.

LJN0209

SIZES

Short:

Small to Large

Regular:

Small to 6X-Large

Long:

Medium to 4X-Large

X-Long:

X-Large to 2X-Large

POCKET DIMENSIONS

Screener Uniform Specification

Unisex Hip Length Parka with Liner

FABRIC

Outershell:

Weft 140 denier 102 filament two ply

Permanent Lining:

Zip Out Liner:

The parka shall be a New Generation 3®, full-cut, hip length model. The parka shall have a Primaloft® zip-in/zip-out liner. Coat construction with sealed seams shall be used throughout with body and sleeves being fully lined.

BODY DETAIL

The front shall be plain with lower box pleated patch pockets. The inside facings shall be made of outer fabric and shall be sewn on top of the nylon lining. There shall be a one-piece back. The shoulders shall have pads. There shall be a 1½” wide inside storm flap from the bottom of the collar to the bottom of the waistband on the right front to maintain windproof quality. There shall be side zipper entry on both side seams, approximately 11” in length and secured by a nylon zipper and snap closure.

INSIDE DETAIL

There shall be a welted pocket on left side of the parka (inside). The pocket opening shall be 4 ½” wide and a minimum of 6” deep. It shall be constructed from lining fabric. Bartacks shall reinforce the opening. There shall be two cut‑in pockets on the left and right sides measuring approximately 5¼” wide and 6" deep. There shall be a strap and snap on the lining of each sleeve end for attaching the zip-in liner.

SLEEVES

The sleeves shall be one piece set with a single needle stitch. The bottom of the sleeve shall have elastic and an adjustable hook and loop tab. A small strap and snap feature shall be sewn to the lower lining area of each sleeve for attaching the zip-in liner.

DRAWSTRING

A concealed drawstring tunnel shall be located at the waistline. The tunnel shall be formed by sewing a strip of fabric to the backside of the back outer shell panel. Top and bottom edges shall be turned under and top stitched at a ⅛” margin. The tunnel shall finish 1” wide and run across the shell back, beginning and ending at the side seams. A 3/16” diameter black painted brass eyelet shall be located in the lining fabric within 1” of each side seam. A ⅛” diameter nylon covered elastic cord shall run through the tunnel and exit through the eyelets. The cord shall be 3” longer than each eyelet when in a fully relaxed state. The cord shall be knotted 1” from each end and shall have an ITW Nexus, or equal, 7/32” diameter barrel lock attached to each end.

BOTTOM

The bottom outer shell fabric shall be a 1 ½” double turned hem.

POCKETS

There shall be two patch pockets with box pleats, finishing approximately 6¼” wide and 7½” deep. Flaps shall be scalloped and self lined. They shall close with hook and loop on the side points and with a centered buttonhole. The pockets shall be self-lined with an opening of approximately 5½” on the side. The left patch pocket is to have a pencil opening at the top of the flap. Both the pockets and the flaps are to be bartacked.

COLLAR

The stand-up collar shall be made from self-material. It shall be interlined with Pellon.

EPAULETS

The epaulets shall be made of 2 layers of body fabric (stitched, turned, and ¼” topstitched) and shall be interlined. They shall be sewn into the sleeve head seam. They shall be "X" stitched at the armhole end and tacked to the jacket at the neck edge. The epaulets shall measure 2 ¼” wide at the armhole end and 1 ¾” wide at the pointed end. Epaulets shall have keyhole buttonholes, with a drilled eyelet, located ¾” from the pointed tip of the epaulet. (The buttonholes shall be centered on the epaulet and run parallel with the long edges of the epaulet.) There shall be a 24 Ligne, flat metal shank button inserted into each drilled eyelet and attached on the under side with an O-ring.

BADGE TAB

The badge tab shall be made of the outer fabric and lined with pocketing being 2” tall by 1” wide. The first eyelet is 1/2” down from the top of the finished edge and the second is 1/2” up from the bottom finished edge. The eyelets are spaced 1” from center to center. It shall be centered 2-1/2” above the left pocket flap.

ZIPPER

There shall be a YKK #5, two-way molded nylon zipper in the front, an 11” nylon zipper on each side vent, and a zipper at the center back neck.

BUTTONS AND SNAPS

The pocket flaps and epaulets have 24 Ligne metal buttons. Flaps and epaulets shall close with 24 ligne metal buttons. Front fly shall be secured by high impact, non-reflective, non-glare, scratch resistant snaps.

THREAD

All seams shall be sewn with polyester core thread or 100% spun polyester thread.

SIZE TAG AND CARE INSTRUCTIONS

Each jacket shall have a sewn in woven size label. There shall also be a printed label with care instructions and each coat marked with lot number, size, fiber content and WPL number.

EMBLEMS

· TSA emblem shall be attached to the right upper sleeve 1 ½” below the sleeve set seam and centered with the epaulet.

· 9-11 Team Spirit emblem shall be attached to the left upper sleeve 1 ½” below the sleeve set seam and centered with the epaulet.

· Large TSA lettered emblem shall be attached to the back 1” below the center back zipper flap.

ZIP IN / ZIP OUT LINER

DESIGN

The liner shall be modeled from a full-cut, long-sleeve liner pattern.

BODY DETAIL

The liner shall have long sleeves and knit wristlets with an anchor loop to accept buttons for attaching the liner to the outer jacket. The edges of the entire body shall be bound with 1‑9/16" nylon bias binding. The side seams, shoulders, and sleeve seams shall be joined with a safety-stitch. The back armholes shall have knit inserts to allow freedom of movement (creating a mock-action back).

POCKET

There shall be one patch pocket located on the lower right of the inside. The pocket shall be bound with nylon bias binding and attached with a single-needle stitch.

ZIPPER

There shall be a molded nylon zipper attached to the liner. This zipper shall correspond with an equal length zipper located on the inside of the outer jacket (used for zipping the liner into the outer jacket).

THREAD

All seams shall be sewn with polyester core thread or 100% spun polyester thread.

SIZE TAG AND CARE INSTRUCTIONS

The liner shall have a sewn‑in label that contains care instructions, style number, fiber content, size, WPL, and county of origin located on the center back below the neck edge.

LJN0209

Short:

Small to Large

Regular:

Small to 6X-Large

Long:

Medium to 4X-Large

X-Long:

X-Large to 2X-Large

DIMENSION SPECIFICATIONS

SLEEVE LENGTH

BACK LENGTH

Screener Uniform Specification

KNIT STOCKING CAP

Fabric: 100% Acrylic, Navy

Style: Pull on knit stocking cap with 3” wide turn up cuff.

TSA embroidery (1.5” letters) on front turn up stitched in silver.

Dimensions:

Length

12 ¾” - 13”

Width

6 ¾”

Navy Ball Cap

FABRIC

65% polyester, 35% cotton Chetopa Twill, 8 oz., dark navy, same fabric as pants

DESIGN

Six panel, low profile baseball cap

FEATURES

· Six panels with eyelet on each panel for ventilation

· Button in center top

· Three double rows of stitching on visor for added strength

· Seams enclosed with fabric tape

· Sweatband

· Adjustable vinyl strap

· Made in USA

EMBELLISHMENTS

TSA embroidered in silver thread (1.5” letters) and centered on front of cap.

TRANSPORTATION SECURITY ADMINISTRATION

TSA Unisex, clip-on ties

FABRIC

Fabric is dark navy 75% (Polyester / 25% Worsted Wool, 11.5 ounces

STYLE

Clip-on tie with French cuff ends. It is a pre-tied four-in-hand knot with all metal bend-over clip. Clasp to be zinc bichromate finish. Finished length is measured from top of knot to tip of tie. Width at widest point is approximately 3”. Small end of tie shall incorporate button down feature with 3 threadless buttonholes spaced 3/8” apart. Tie shall be constructed with a label loop for holding large end of tie when button down feature is utilized. It is available in three lengths.

AVAILABLE SIZES

15”

18” 20”

TRANSPORTATION SECURITY ADMINISTRATION

MALE UNIFORM ITEMS

TSA Men's Long Sleeve Shirt

FABRIC

Royal Blue 4.25 oz sq yd 65% polyester 35% cotton soft hand, Somerset/Touchtex Finish.

DESIGN

The shirt shall be based on a security style pattern. It shall have a banded collar, sleeve plackets and cuffs, pleated breast pockets, epaulets, and a back yoke.

SLEEVES

The sleeves shall have tailored sleeve plackets that are set with a single needle stitch. They shall finish 1 3/8” long by 7/8” wide. They shall have doghouse tacks that form box plackets. The cuffs shall be set to the sleeves with a single needle stitch, and shall have two pleats at the buttonhole end of the cuff. The cuffs shall be constructed from two-pieces of body fabric and shall be interlined with Pellon. They shall have round corners, and shall be topstitched with a ¼” margin. The cuff shall fasten with a 2-button, 1-buttonhole closure. The buttons shall be horizontally set on the cuff. The cuffs shall measure 2 ½” wide.

POCKETS

Two breast pockets finishing 5-3/8" wide and 5¾” long with mitered corners. Both pockets have a 1½” box-pleat stitched top and bottom to prevent spreading. Left pocket has a sewn through pencil stall 1‑3/8" wide. Woven hook fastener ½” wide and 1" long is placed on each pocket to secure woven loop fastener placed on each flap.

FLAPS

Flaps are scalloped, finishing 5½” in width, 2¾” in length at the center and 2½” at each side. Flaps are placed with a ¼” space between the pocket and flap and have one centered buttonhole with button. The left flap has a pencil opening 1‑3/8" in width. Woven loop fastener ½” wide and 1" long is placed on the edges of each flap to secure woven hook fastener placed on pockets. Flaps have crease interlining. Right flap will have two eyelets for name plates 1” down from the top of the flap that will be spaced 1-7/8” from center to center and centered above the center point on the flap.

EPAULETS

The shirt shall have pointed non-tapering epaulets on each shoulder. They shall be constructed from two pieces of body fabric (creased and edge-stitched) and interlined with Pellon. The epaulets shall be functional as to accommodate shoulder boards. A buttonhole shall be sewn in the center of the epaulet (parallel with the long edges of the epaulet) ¾” from the tip of the pointed end. The button shall fasten to a corresponding 17 Ligne, 4-eye button sewn on the yoke. The epaulets shall be set into the armhole seam. They shall not have any “X” stitching at the armhole end. The front edge of the epaulet shall be placed parallel with the shoulder seam and shall slightly cover the seam (about ¼”). The epaulets shall measure 1 ½” wide. Their length shall grade with the shoulder seam as shirt increases/decreases in size, with the tip finishing 1 ⅛” from the neck seam.

SEAMS

The sleeve and side seams shall be sewn with a four-thread safety stitch at a ¼” margin. The shoulder join sewn shall be sewn with a single needle stitch. The yoke shall be turned so that all stitching is concealed.

FRONT

The left front shall have a 1 ⅜” wide placket. It shall be cut-on, lined with Pellon, and have two rows of topstitching, ¼” margin from each edge. The left front placket shall have 6 vertical buttonholes. The right front shall have a ⅞” double-turned hem, single needle topstitched at a ¾” margin. The right front shall have six 17 Ligne, 4-eye buttons that fasten to corresponding buttonholes

TRANSPORTATION SECURITY ADMINISTRATION

TSA Men's Short Sleeve Shirt

FABRIC

Royal Blue 4.25 oz. sq. yd. 65% polyester / 35% cotton, soft hand, Somerset/Touchtex finish.

CREASING

The two military creases in front and three in back of each shirt incorporate a permanent modified silicone crease produced by the Lintrak® System.

FRONT

The left front has a self-fabric center pleat 1‑3/8" wide with a 3 ¼” facing extending from neckline to bottom of shirt. It has two rows of stitching 7/8" apart. The center pleat is interlined with 100% polyester, 250 denier. Right front has a 3 ¼” revere facing extending from neckline to bottom of shirt. The right front has seven buttons.

COLLAR

Convertible collar measures 2‑7/8" long at points and is topstitched 3/16" from the edge. The interlinings are 100% polyester, 250 denier. Permanent collar stays of proper length are fused or sewn inside collar so that no stitches are made through the bottom leaf.

YOKE

Two piece yoke of self-goods cut in filling direction to enhance stretch. The back of the yoke is topstitched 1/16".

SLEEVES

Sleeves are one piece, have a 7/8" hem and finish 10-3/8" long from the shoulder seam on a size Large 16-16 ½. Sleeve setting and closing are sewn with an overedge and safety stitch. The sleeve is bartacked at the hem.

POCKETS

Two breast pockets finishing 5‑3/8" wide and 5 ¾” long with mitered corners. Both pockets have a 1 ½” box-pleat stitched top and bottom to prevent spreading. Left pocket has a sewn through pencil stall 1‑3/8" wide. Woven hook fastener ½” wide and 1" long is placed on each pocket to secure woven loop fastener placed on each flap.

FLAPS

Flaps are scalloped, finishing 5 ½” in width, 2 ¾” in length at the center and 2 ½” at each side. Flaps are placed with ¼” space between the pocket and flap and have one centered buttonhole with button. The left flap has a pencil opening 1‑3/8" in width. Woven loop fastener ½” wide and 1" long is placed on the edges of each flap to secure woven hook fastener placed on pockets. Flaps have crease interlining. Right flap will have two eyelets for name plates 1” down from the top of the flap that will be spaced 1-7/8” from center to center and centered above the center point on the flap.

BADGE TAB

Inside sling type of self‑goods approximately 1-1/8" wide extends from joining seam to pocket of left front. To have two small, uncut buttonholes 1 ¼” apart with the lower buttonhole 1 ¼” above the flap.

EPAULETS

Sewn into sleeve head seam and measure approximately 1‑7/8" tapering to 1 ½” with end pointed. Epaulets are set approximately 1" from the collar seam. Epaulets have crease interlining.

SHIRT LABELING

Each garment is identified by permanent size label, style number, cut number, manufacturing RN number, care, content and country of origin labeling.

BUTTONS

20-ligne melamine buttons dyed to match the fabric color.

PACKING

Shirts are polybagged individually.

EMBLEMS AND EMBROIDERY

· TSA shoulder emblem shall be sewn on the right sleeve. Shall be placed 1 ½” below the sleeve set seam, centered with the center of the epaulet.

· A TSA 9 -11 Team Spirit emblem shall be sewn on the left sleeve. Shall be placed 1 ½” below the sleeve set seam, centered with the center of the epaulet.

TRANSPORTATION SECURITY ADMINISTRATION

TSA Male Relaxed Fit Trouser

FABRIC

Dark Navy 8 oz. 65% polyester 35% cotton twill.

DESIGN

The trousers shall be made on a modified male relaxed uniform pattern. They shall have a plain front with quarter-top front pockets and two back hip pockets.

POCKETS

The front pockets shall have a minimum opening of 6 ½" and shall be 12” deep (total pocket bag depth). The pocket bags shall be stitched, turned, and re-stitched. The inside front pocket facing shall be a separate piece of body fabric, finishing no less than 1 ¼” wide. The back pockets will have a minimum opening of 5 ½" and shall be 6” deep. (Sizes 29 and smaller shall have a back pocket opening that measures no less than 5”.) Back hip pockets shall be made with a PW automatic machine. They shall be finished on the outside with an exposed top and bottom welt. The left back pocket shall have a tab and button closure. The front pockets shall each have a straight bartack at the top of the opening, and a triangular bartack at the bottom of the opening. The back pockets shall have triangular bartacks at each end of the pocket opening.

POCKETING

The pocketing shall be black, 80% polyester / 20% cotton, plain weave, 4.75 ounces per square yard with Visa® for soil release, moisture transport, and thermal management.

WAISTBAND

The waistband is to finish 2" wide and will be closed with a crush‑proof hook and eye, the eye being bar tacked for stability. The waistband curtain, attached with a rocap machine, is to be made from the pocketing fabric and have three-row Snugtex. Ban-Rol waistband stiffener, 3/4" wide, is to be sewn into the waistband on the front of the trouser from side seam to side seam. The full length of the waistband is to be fused with non-woven fusible interlining. The trousers are to be made with a continuous closed waistband. The waistband is to be set on and stitched below the lower edge through the outer fabric and the waistband curtain.

INSIDE TRIM

The right fly lining shall be made from the same fabric as the waistband curtain. A separate French fly, constructed from body fabric, shall be sewn to the inside right fly and shall fasten to a button on the left front waistband curtain.

BELT LOOPS

There shall be a minimum of five (5) belt loops on waist sizes 30 and down, seven (7) belt loops on waist sizes 31 to 48, and a minimum of nine (9) on sizes 50 and larger. Each loop shall be ¾” wide and interlined with a non-woven fusible interlining. The belt loops shall be topstitched with a double needle stitch. Except for the center back loop, which shall be inserted in the top of the waistband and dropped tacked on the bottom, all loops shall be inserted in the top and bottom of the waistband. They shall accommodate a 1 ⅝" belt.

ZIPPER

The trousers shall be closed with a YKK brass zipper which has a brass bottom stop at the base of the zipper chain and a brass ratcheting cam lock slider. The inside left fly shall be reinforced with Pellon under the zipper stitching. There shall be a straight bartack sewn at the bottom of the fly through all layers (the zipper tape, the right and left flies and the right fly lining). The right and left flies shall be joined by an additional bartack on the inside of the trouser.

BUTTONS

Buttons used for the French fly and left, back hip pocket shall be 22 Ligne melamine, 4-hole style, dyed to match the fabric color.

CREASING

The front and rear leg creases must incorporate a permanent modified silicone crease produced by the “Lintrak® System”.

SEAMING

The entire trouser shall be seamed with polyester core thread. The seat seam shall be stitched with a tandem needle seat-seaming machine. Outside leg seams shall have Copen Blue cordedge stitched into the seam. All exposed inside seams of the trouser shall be serged.

LABELING

Trousers shall be labeled with the following information: style number, size, fiber content, care instructions, WPL number, and country of origin.

FINISHING AND PRESSING

All loose threads must be removed. The trousers shall have the side seams, inseam, and seat seam pressed open.

TRANSPORTATION SECURITY ADMINISTRATION

TSA Male Regular Fit Trouser

FABRIC

Dark Navy 8 oz. 65% polyester 35% cotton twill.

DESIGN

The trousers shall be made on a male relaxed uniform pattern. They shall have a plain front with quarter-top front pockets and two back hip pockets.

POCKETS

The front pockets shall have a minimum opening of 6 ½" and shall be 12” deep (total pocket bag depth). The pocket bags shall be stitched, turned, and re-stitched. The inside front pocket facing shall be a separate piece of body fabric, finishing no less than 1 ¼” wide. The back pockets will have a minimum opening of 5 ½" and shall be 6” deep. (Sizes 29 and smaller shall have a back pocket opening that measures no less than 5”.) Back hip pockets shall be made with a PW automatic machine. They shall be finished on the outside with an exposed top and bottom welt. The left back pocket shall have a tab and button closure. The front pockets shall each have a straight bartack at the top of the opening, and a triangular bartack at the bottom of the opening. The back pockets shall have triangular bartacks at each end of the pocket opening.

POCKETING

The pocketing shall be black, 80% polyester / 20% cotton, plain weave, 4.75 ounces per square yard with Visa® for soil release, moisture transport, and thermal management.

WAISTBAND

The waistband is to finish 2" wide and will be closed with a crush‑proof hook and eye, the eye being bar tacked for stability. The waistband curtain, attached with a rocap machine, is to be made from the pocketing fabric and have three-row Snugtex. Ban-Rol waistband stiffener, 3/4" wide, is to be sewn into the waistband on the front of the trouser from side seam to side seam. The full length of the waistband is to be fused with non-woven fusible interlining. The trousers are to be made with a continuous closed waistband. The waistband is to be set on and stitched below the lower edge through the outer fabric and the waistband curtain.

INSIDE TRIM

The right fly lining shall be made from the same fabric as the waistband curtain. A separate French fly, constructed from body fabric, shall be sewn to the inside right fly and shall fasten to a button on the left front waistband curtain.

BELT LOOPS

There shall be a minimum of five (5) belt loops on waist sizes 30 and down, seven (7) belt loops on waist sizes 31 to 48, and a minimum of nine (9) on sizes 50 and larger. Each loop shall be ¾” wide and interlined with a non-woven fusible interlining. The belt loops shall be topstitched with a double needle stitch. Except for the center back loop, which shall be inserted in the top of the waistband and dropped tacked on the bottom, all loops shall be inserted in the top and bottom of the waistband. They shall accommodate a 1 ⅝" belt.

ZIPPER

The trousers shall be closed with a YKK brass zipper which has a brass bottom stop at the base of the zipper chain and a brass ratcheting cam lock slider. The inside left fly shall be reinforced with Pellon under the zipper stitching. There shall be a straight bartack sewn at the bottom of the fly through all layers (the zipper tape, the right and left flies and the right fly lining). The right and left flies shall be joined by an additional bartack on the inside of the trouser.

BUTTONS

Buttons used for the French fly and left, back hip pocket shall be 22 Ligne melamine, 4-hole style, dyed to match the fabric color.

CREASING

The front and rear leg creases must incorporate a permanent modified silicone crease produced by the “Lintrak® System”.

SEAMING

The entire trouser shall be seamed with polyester core thread. The seat seam shall be stitched with a tandem needle seat-seaming machine. Outside leg seams shall have Copen Blue cordedge stitched into the seam. All exposed inside seams of the trouser shall be serged.

LABELING

Trousers shall be labeled with the following information: style number, size, fiber content, care instructions, WPL number, and country of origin.

FINISHING AND PRESSING

All loose threads must be removed. The trousers shall have the side seams, inseam, and seat seam pressed open.

TRANSPORTATION SECURITY ADMINISTRATION

Male Short

FABRIC

Dark navy, 8 oz. 65% polyester 35% cotton twill.

DESIGN

The short shall be made on a relaxed uniform walk short pattern. They shall have a plain front with quarter top front pockets, two back pockets and darts in the center back panels.

POCKETS

The front pockets shall have a minimum opening of 6 ½". The pocket bags shall be stitched, turned, and re-stitched. The inside front pocket facing shall be a separate piece of body fabric, finishing no less than 1 ¼” wide. The back pockets shall have a minimum opening of 5 ½" and shall be 6” deep. (Sizes 29 and smaller shall have a back pocket opening that measures no less than 5”.) Back hip pockets shall be made with a PW automatic machine. They shall be finished on the outside with an exposed top and bottom welt. The left back pocket shall have a tab and button closure. The front pockets shall each have a straight bartack at the top of the opening, and a triangular bartack at the bottom of the opening. The back pockets shall have triangular bartacks at each end of the pocket opening.

POCKETING

The pocketing shall be black, 80% polyester / 20% cotton, plain weave, 4.75 ounces per square yard with Visa® for soil release, moisture transport, and thermal management.

WAISTBAND

The waistband shall finish 2" wide and shall be closed with a crush‑proof hook and eye (the eye shall be bartacked for stability). The waistband shall have a Snug-Tex curtain attached with a Rocap machine. It shall be made from the pocketing fabric and have tow Snug-Tex bands to hold the shirt in place. Ban-Rol waistband stiffener, ¾” wide, shall be sewn into the waistband on the front of the short from side seam to side seam. The full length of the waistband shall be fused with non-woven fusible interlining. The shorts shall be made with a continuous closed waistband. The waistband shall be finished to the waistband curtain by means of the stitching-in-the-ditch method.

INSIDE TRIM

The right fly lining shall be made from the same fabric as the waistband curtain. A separate French fly, constructed from body fabric, shall be sewn to the inside right fly and shall fasten to a button on the left front waistband curtain.

BELT LOOPS

There shall be a minimum of five (5) belt loops on waist sizes 30 and down, seven (7) belt loops on waist sizes 31 to 49, and a minimum of nine (9) on sizes 50 and larger. Each loop shall be ¾” wide and interlined with a non-woven fusible interlining. The belt loops shall be topstitched with a double needle stitch. Except for the center back loop, which shall be inserted in the top of the waistband and dropped tacked on the bottom; all loops shall be inserted in the top and bottom of the waistband. They shall accommodate a 1 ⅝" belt.

ZIPPER

The shorts shall be closed with a YKK brass zipper which has a brass bottom stop at the base of the zipper chain and a brass ratcheting cam lock slider. The inside left fly shall be reinforced with Pellon under the zipper stitching. There shall be a straight bartack sewn at the bottom of the fly through all layers (the zipper tape, the right and left fly’s and the right fly lining). The right and left flys shall be joined by an additional bartack on the inside of the short.

BUTTONS

Buttons used for the French fly and the left back hip pocket shall be 22 Ligne melamine, 4-hole style, dyed to match the fabric color.

CREASING

The front and rear leg creases must incorporate a permanent modified silicone crease produced by the “Lintrak® System”.

SEAMING

The entire short shall be seamed with polyester core thread. The seat seam shall be stitched with a tandem needle seat-seaming machine. All exposed inside seams of the short shall be serged.

LABELING

Shorts shall be labeled with the following information: style number, size, fiber content, care instructions, WPL number, and country of origin.

FINISHING AND PRESSING

All loose threads must be removed. The shorts shall have the side seams, inseam, and seat seam pressed open.

Stock Sizes:

28 through 54 (even)

TRANSPORTATION SECURITY ADMINISTRATION

TSA Men's 100% Cotton Long Sleeve Shirt

FABRIC

Royal Blue 6 oz sq yd 100% cotton Durable Press.

DESIGN

The shirt shall be based on a security style pattern. It shall have a banded collar, sleeve plackets and cuffs, pleated breast pockets, epaulets, and a back yoke.

FRONT

The left front shall have a 1 ⅜” wide placket. It shall be cut-on, lined with Pellon, and have two rows of topstitching, ¼” margin from each edge. The left front placket shall have 6 vertical buttonholes. The right front shall have a ⅞” double-turned hem, single needle topstitched at a ¾” margin. The right front shall have six 19 Ligne, 4-eye buttons that fasten to corresponding buttonholes on the left front. The buttonholes (on the left front) and buttons (on the right front) shall be spaced 3 ¾” apart, center to center. The shirt shall fasten left over right.

SLEEVES

The sleeves shall have tailored sleeve plackets that are set with a single needle stitch. They shall finish 6 ¼” long by 1 ¼” wide. They shall have doghouse tacks that form box plackets. The cuffs shall be set to the sleeves with a single needle stitch, and shall have a pleat at the buttonhole end of the cuff. The cuffs shall be constructed from two-pieces of body fabric and shall be interlined with Pellon. They shall have round corners, and shall be topstitched with a ¼” margin. The cuff shall fasten with a 2-button, 2-buttonhole closure. The buttons shall be vertically set on the cuff. The cuffs shall measure 2 ¾” wide.

POCKETS

Two breast pockets finishing 5-3/8" wide and 5¾” long with mitered corners. Both pockets have a 1½” box-pleat stitched top and bottom to prevent spreading. Left pocket has a sewn through pencil stall 1‑3/8" wide.