Solicitation Multi-Cutter Rev1.doc

DOC document 867 KB Posted

Attached to
USCGC KODIAK ISLAND, USCGC KEY BISCAYNE AND USCGC DRUMMOND DRY-DOCK REPAIRS
Solicitation number
HSCG80-12-Q-PHM047
Issued by

About this file

Corrected Solicitation Rev 1

View the file

Other files

File Type Posted
A0007.doc DOC document
Drummond Blank Estimate.xlsx XLSX spreadsheet
A0006.doc DOC document
Amendment 5.pdf PDF
DRUMMOND —
KODIAK ISLAND —
KEY BISCAYNE —
KEY BISCAYNE —
KODIAK ISLAND —
DRUMMOND —
Amendment 4.pdf PDF
DRUMMOND —
SF30-A003.pdf PDF
KEY BISCAYNE —
KODIAK ISLAND —
110C-WPB_581_2_1_-_B.pdf PDF
110C-WPB_581_2_3_-_A.pdf PDF
110C-WPB_581_2_2_-_-.pdf PDF
Amendment2.pdf PDF
OEM Heat Exchanger Drawings.pdf PDF
Amendment 1.pdf PDF
KEY BISCAYNE —
DRUMMOND —
KODIAK ISLAND —
Show all 24

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

HSCG80-12-Q-PHM047 PAGE 8 OF 62

USCGC’S KODIAK ISLAND/KEY BISCAYNE/DRUMMOND

MULTI CUTTER DRYDOCK REPAIRS

NOTICE FOR FILING AGENCY PROTESTS

United States Coast Guard Ombudsman Program

It is the policy of the United States Coast Guard (USCG) to issue solicitations and make contract awards in a fair and timely manner. The Ombudsman Program for Agency Protests (OPAP) was established to investigate agency protest issues and resolve them without expensive and time-consuming litigation. OPAP is an independent reviewing authority that is empowered to grant a prevailing protester essentially the same relief as the Government Accountability Office (GAO).

Interested parties are encouraged to seek resolution of their concerns within the USCG as an Alternative Dispute Resolution (ADR) forum rather than filing a protest with the GAO or some external forum. Interested parties may seek resolution of their concerns informally or opt to file a formal agency protest with the Contracting Officer or Ombudsman.

Informal Forum with the Ombudsman. Interested parties who believe a specific USCG procurement is unfair or otherwise defective should first direct their concerns to the applicable Contracting Officer. If the Contracting Officer is unable to satisfy their concerns, interested parties are encouraged to contact the U.S. Coast Guard Ombudsman for Agency Protests. Under this informal process the agency is not required to suspend contract award performance. Use of an informal forum does not suspend any time requirement for filing a protest with the agency or other forum. In order to ensure a timely response, interested parties should provide the following information to the Ombudsman: solicitation/contract number, contracting office, Contracting Officer, and solicitation closing date (if applicable).

Formal Agency Protest with the Ombudsman. Prior to submitting a formal agency protest, protesters must first use their best efforts to resolve their concerns with the Contracting Officer through open and frank discussions. If the protester’s concerns are unresolved, an Independent Review is available by the Ombudsman. The protester may file a formal agency protest to either the Contracting Officer or as an alternative to that, the Ombudsman under the OPAP program. Contract award or performance will be suspended during the protest period unless contract award or performance is justified, in writing, for urgent and compelling reasons or is determined in writing to be in the best interest of the Government. The agency’s goal is to resolve protests in less than 35 calendar days from the date of filing. Protests shall include the information set forth in FAR 33.103(d) (2). If the protester fails to submit the required information, resolution of the protest may be delayed or the protest may be dismissed. To be timely protests must be filed within the period specified in FAR 33.103(e). Formal protests filed under the OPAP program should be submitted to:

COMMANDANT (CG-9131)

U S COAST GUARD

OMBUDSMAN PROGRAM FOR AGENCY PROTESTS

2100 2ND ST SW STOP 7112

WASHINGTON DC 20593-7112

The Ombudsman Hotline telephone number is 202.372.3695.

Commander

U.S. Coast Guard

Surface Forces Logistics Center

CPD-C&P1-PBPL

300 East Main Street, Suite 550 Norfolk, VA 23510

REQUEST FOR QUOTES

HSCG80-12-Q –PHM047

USCGC KODIAK ISLAND, USCGC KEY BISCAYNE AND USCGC DRUMMOND DRY-DOCK REPAIRS

SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL ITEMS

OFFEROR TO COMPLETE BLOCKS 12, 17, 23, 24, & 30

1. REQUISITION NUMBER

2. CONTRACT NO.

3. AWARD/EFFECTIVE

DATE

4. ORDER NUMBER

5. SOLICITATION NUMBER

HSCG80-12-Q-PHM047

6. SOLICITATION

ISSUE DATE

12/1/2011

7. FOR SOLICITATION INFORMATION CALL:
a. NAME

Chas Hartley

b. TELEPHONE NUMBER (no collect calls)

(757) 628-4657

8. OFFER DUE DATE/ LOCAL TIME

1/4/12 3:00 P.M. EASTERN TIME

9. ISSUED BY CODE 75174

USCG Surface Forces Logistics Center

Attn: Chas Hartley 300 E Main Street, Suite 550

Norfolk, VA 23510

E-mail: chas.f.hartley@uscg.mil

10. THIS ACQUISITION IS FORMCHECKBOX

UNRESTRICTED OR

FORMCHECKBOX

SET ASIDE: 100 %FOR:

FORMCHECKBOX

SMALL BUSINESS

FORMCHECKBOX

WOMEN-OWNED SMALL

BUSINESS (WOSB)

HUBZONE SMALL

NAICS:

BUSINESS

ECONOMICALLY DISADVANTAGED

WOMEN-OWNED SMALL (EDWOSB)

SERVICE-DISABLED

VETERAN-OWNED

SIZE STANDARD:

SMALL BUSINESS

8(A)

11. DELIVERY FOR FOB DESTINATION UNLESS BLOCK IS MARKED

FORMCHECKBOX

SEE SCHEDULE

12. DISCOUNT

TERMS

FORMCHECKBOX

13a. THIS CONTRACT IS A RATED ORDER UNDER DPAS (15 CFR 700) 13b. RATING DO-A3

14. METHOD OF SOLICITATION

RFQ FORMCHECKBOX

IFB FORMCHECKBOX

RFP

15. DELIVER TO CODE

See Description of Supplies/Services

16. ADMINISTERED BY CODE

Same as block 9

17a. CONTRACTOR/ CAGE CODE FACILITY

OFFEROR CODE

DUNS No.

TELEPHONE NO:

FAX NO:

18a. PAYMENT WILL BE MADE BY CODE USCG Finance Center

1430A Kristina Way

Chesapeake, VA 23326

FORMCHECKBOX

17b. CHECK IF REMITTANCE IS DIFFERENT AND PUT SUCH ADDRESS IN OFFER 18b. SUBMIT INVOICES TO ADDRESS SHOWN IN BLOCK 18a UNLESS BLOCK BELOW IS CHECKED FORMCHECKBOX

SEE ADDENDUM

19.

ITEM NO.

20.

SCHEDULE OF SUPPLIES/SERVICES

21.

QUANTITY

22.

UNIT

23.

UNIT PRICE

24.

AMOUNT

Dry-Dock Repairs on the UCSGC Kodiak Island, USCGC Key Biscayne and USCGC Drummond In accordance with this solicitation and attached specification

Must Check Appropriate box on page 4

25. ACCOUNTING AND APPROPRIATION DATA

26. TOTAL AWARD AMOUNT (FOR GOVT USE ONLY)

FORMCHECKBOX

27a. SOLICITATION INCORPORATES BY REFERENCE FAR 52.212-1, 52.212-4. FAR 52.212-3 & 52.212-5 ARE ATTACHED. ADDENDA FORMCHECKBOX

ARE FORMCHECKBOX

ARE NOT ATTACHED.

FORMCHECKBOX

27b. CONTRACT/PURCHASE ORDER INCORPORATES BY REFERENCE FAR 52.212-4, FAR 52.212-5 IS ATTACHED. ADDENDA FORMCHECKBOX

ARE FORMCHECKBOX

ARE NOT ATTACHED.

FORMCHECKBOX

28. CONTRACTOR IS REQUIRED TO SIGN THIS DOCUMENT AND RETURN COPIES TO ISSUING OFFICE. CONTRACTOR AGREES TO FURNISH AND DELIVER ALL ITEMS SET FORTH OR OTHERWISE IDENTIFIED ABOVE AND ON ANY ADDITIONAL SHEETS SUBJECT TO THE TERMS AND CONDITIONS SPECIFIED HEREIN.

FORMCHECKBOX

29. AWARD OF CONTRACT: REFERENCE

OFFER DATED . YOUR OFFER ON SOLICITATION (BLOCK 5), INCLUDING ANY ADDITIONS OR CHANGES WHICH ARE SET FORTH HEREIN, IS ACCEPTED AS TO ITEMS:

30a. SIGNATURE OF OFFEROR/CONTRACTOR

31a. UNITED STATES OF AMERICA (SINGATURE OF CONTRACTING OFFICER)

30b. NAME AND TITLE OF SIGNER

30c. DATE SIGNED

31b. NAME OF CONTRACTING OFFICER

31c. DATE SIGNED

AUTHORIZED FOR LOCAL REPRODUCTION

STANDARD FORM 1449 (Rev. 3/2011)

PREVIOUS EDITION IS NOT USABLE

Prescribed by GSA – FAR (48 CFR) 53.212

19.

ITEM NO.

20.

SCHEDULE OF SUPPLIES/SERVICES

21.

QUANTITY

22.

UNIT

23.

UNIT PRICE

24.

AMOUNT

SEE PAGES X-XX

32a. QUANTITY IN COLUMN 21 HAS BEEN

FORMCHECKBOX

RECEIVED

FORMCHECKBOX

INSPECTED

ACCEPTED, AND CONFORMS TO THE CONTRACT, EXCEPT AS NOTED:

32b. SIGNATURE OF AUTHORIZED GOVERNMENT

REPRESENTATIVE

32c. DATE

32d. PRINTED NAME AND TITLE OF AUTHORIZED GOVERNMENT REPRESENTATIVE

32e. MAILING ADDRESS OF AUTHORIZED GOVERNMENT REPRESENTATIVE

32f. TELEPHONE NUMBER OF AUTHORIZED GOVERNMENT REPRESENTATIVE

32g. E-MAIL OF AUTHORIZED GOVERNMENT REPRESENTATIVE

33. SHIP NUMBER

34. VOUCHER NUMBER

35. AMOUNT VERIFIED CORRECT FOR

36. PAYMENT

FORMCHECKBOX

COMPLETE

FORMCHECKBOX

PARTIAL

FORMCHECKBOX

FINAL

37. CHECK NUMBER

FORMCHECKBOX

PARTIAL FORMCHECKBOX

FINAL

38. S/R ACCOUNT NUMBER

39. S/R VOUCHER NUMBER

40. PAID BY

41a. I CERTIFY THIS ACCOUNT IS CORRECT AND PROPER FOR PAYMENT

42 a. RECEIVED BY (Print)

41b. SIGNATURE AND TITLE OF CERTIFYING OFFICER
41c. DATE

42b. RECEIVED AT (Location)

42c. DATE REC’D (YY/MM/DD)

42d. TOTAL CONTAINERS

AUTHORIZED FOR LOCAL REPRODUCTION

STANDARD FORM 1449 (Rev. 3/2011)

PREVIOUS EDITION IS NOT USABLE

Prescribed by GSA – FAR (48 CFR) 53.212

CONTINUATION OF SF 1449 – BLOCKS 17a - 25

(1) Block 17a: Contractor shall include DUNS number.

(2) Block 17b: REMITTANCE ADDRESS: Payment will be made to the Financial Institution listed in Central Contractor Registration (CCR). To receive award Contractor must be registered in Central Contract Registration (CCR) http://www.ccr.gov.

(3) Block 19 through 24: SEE SCHEDULE OF SUPPLIES/SERVICES BELOW.

(4) Block 25: ACCOUNTING AND APPROPRIATION DATA: To be included on contract award document.

DESCRIPTION OF WORK:(a) The Contractor shall furnish all necessary labor, material, services, equipment, supplies, power, accessories, facilities and such other things as are necessary, except as otherwise specified, to perform Dry-Dock repairs, and alterations to the vessels, in accordance with this solicitation and attached specifications. This acquisition is for the procurement of Dry-Dock repairs including 83 work items on the USCGC Key Biscayne, 102 work items on the USCGC Kodiak Island and 104 work items on the USCGC Drummond. See attached specification for detailed information.

(b) Failure to read the specifications in their entirety will not relieve the quoter from the responsibility for properly estimating the difficulty or price of successfully performing the work. Failure to do so will be at the quoter 's risk. All proposals submitted in response to this solicitation shall stand firm for 60 calendar days from the response date of this solicitation.

ALL CONTRACTORS ARE RESPONSIBLE FOR VERIFYING THE RECEIPT OF THEIR QUOTES/PROPOSALS.

REQUIRED DOCUMENTS:

Each quoter shall furnish the information required by the solicitation, which includes:

1. Signed 1449 with offeror’s address, DUNS and other information completed.

2. Price Schedule filled out with a cost associated with each CLIN

3. Past Performance Documentation

4. Small Business Self Certification

5. Welding Certifications and Procedures

6. Drydock Certification

7. Proof of Insurance (Statement of Coverage from current Insurance carrier)

Mailed and e-mailed quotes will be accepted. Faxed quotes will not be accepted. E-mailed quotes may be sent to Chas Hartley at chas.f.hartley@uscg.mil.

PLEASE NOTE: QUOTES THAT DO NOT INCLUDE ALL REQUIRED DOCUMENTS MAY BE CONSIDERED INCOMPLETE AND MAY NOT BE CONSIDERED

GEOGRAPHIC RESTRICTION: No award will be made to a facility that is more than 576 nautical miles from Key West, Florida.

ALL WORK WILL BE PERFORMED AT THE CONTRACTORS FACILITY

ANTICIPATED AWARD DATE: The contract is expected to be awarded on or about January 11, 2012. Work covered by this solicitation shall be completed within 66 calendar days for the USCGC Key Biscayne and USCGC Kodiak Island. The USCGC Drummond shall be completed in 108 calendar days. All three vessel’s performance period starts from the date the vessel becomes available to the Contractor.

The performance period’s are:

USCGC KODIAK ISLAND 22FEB2012 to 27APR2012

USCGC KEY BISCAYNE 16MAY2012 to 20JUL2012

USCGC DRUMMOND 08AUG2012 to 23NOV2012

An arrival conference normally will be held within 48 hours of the scheduled start date. Vessels being drydocked shall be in drydock within seventy-two (72) hours of delivery. If a pre-docking shaft alignment is being performed, the vessel shall be drydocked within one-hundred and twenty (120) hours after arrival.

QUESTIONS AND REQUEST FOR DRAWINGS: The last day to request drawings or ask questions regarding this solicitation is December 28, 2011 at 3:00 eastern time. After this date further requests may not be accepted due to time constraints.

Contract Type: This solicitation will result in a single or multiple award(s) Firm Fixed-Price Contract based on the responses that are received. Interested Vendors must be aware that they have the option to compete on one or all three of the 110’cutters. Interested vendors may also submit multiple proposals in response to this solicitation. For example, a vendor may submit one solicitation that encompasses the work on all three Cutters and/or submit individual proposals for the work on one or more individual cutters. Each proposal will be evaluated independently. If a contractor submits just one proposal that includes all three Dry-Docks they may be awarded one or two of the Dry-Dock projects at that proposed price unless they note in their proposal that the price is contingent on award of all three cutters. It is the Governments decision whether to make one or multiple awards based on the responses that are received.

SCHEDULE OF SUPPLIES/SERVICES: SCHEDULE OF SUPPLIES/SERVICES: See Schedule of Supplies and Services. Base Contract Line Item Numbers (CLINs) are marked as “D” for Definitive. Optional CLINS are marked “O” for Optional. Insert unit prices in all CLINs listed in the Schedule unless “NSP” is printed in the Unit Price column for any CLIN. “NSP” in the section means “Not Separately Priced.”

USCGC Kodiak Island

Performance Period: 22FEB2012 to 27APR2012

ITEM
DESCRIPTION
UNIT PRICE
UNIT
QTY
EXTENDED PRICE
D-001
Hull Plating, U/W Body, Inspect
JOB
1
O-002
Hull Plating (U/W Body), Ultrasonic Testing
500 SHOTS
10
O-003
Perform Steel Hull and Structural Plating Repairs (10-Pound or 10.2-Pound)
4 SQFT
10
O-004
Aluminum Hull and Structural Repairs - 1/4" Plate
4 SQFT
50
O-005
Aluminum Hull and Structural Repairs - 3/16" Plate
4 SQFT
25
O-006
Aluminum Hull and Structural Repairs - 5/16" Plate
4 SQFT
25
O-007
Hull and Structural Plating Repairs -Crack (Aluminum)
1 LF
50
O-008
Hull and Structural Plating Repairs - Crack (Steel)
1 LF
50
O-009
Hull and Structural Plating Repairs - Eroded Weld (Aluminum)
1 LF
50
O-010
Steel Hull and Structural Plating Repairs (5-Pound)
4 SQFT
50
O-011
Steel Hull and Structural Plating Repairs (7.0-Pound 7.5-Pound or 7.65-Pound)
4 SQFT
50
O-012
Steel Hull and Structural Plating Repairs , Corrugated Plate (4.0-Pound)
4 SQFT
10
O-013
Hull and Structural Plating Repairs (6.0-Pound or 5.63-Pound)
4 SQFT
10
D-014
Appendages (U/W), Leak Test
JOB
1
D-015
Propulsion Shaft Rope Guards , Inspect and Repair
JOB
1
O-016
Appendages (U/W) - Internal, Preserve
JOB
1
D-017
Tanks (MP Fuel Service), Clean and Inspect
JOB
1
D-018
Voids (Non-Accessible), Leak Test
JOB
1
D-019
Tanks (MP Fuel Stowage and Overflow), Clean and Inspect
JOB
1
O-020
Voids (Non-Accessible), Preserve Internal Surfaces
JOB
1
D-021
Tanks, Air Test
JOB
1
D-022
WORK ITEM DELETED
JOB
1
D-023
Tanks (Potable Water), Clean and Inspect
JOB
1
D-024
WORK ITEM DELETED
JOB
1
D-025
Tanks (Dirty Oil and Waste), Clean and Inspect
JOB
1
D-026
Main Diesel Engine, Renew
JOB
1
D-027
Propulsion Shafting, Remove, Inspect, and Reinstall
JOB
1
D-028
Mechanical Shaft Seal Assemblies, Overhaul
JOB
1
D-029
WORK ITEM DELETED
JOB
1
O-030
Propulsion Shaft Bearings (External) , Renew
JOB
1
O-031
Propulsion Shaft Stern Tube Bearings , Renew
JOB
1
D-032
Propellers ; Remove, Inspect, and Reinstall
JOB
1
O-033
Propeller , Repair Root Erosion
JOB
1
D-034
MDE Exhaust System , Inspect
JOB
1
D-035
Heat Exchangers , Clean and Inspect
JOB
1
D-036
Fathometer Transducer, Renew
JOB
1
D-037
Fathometer Transducer , General Maintenance
JOB
1
D-038
Speed Doppler, Renew, Doppler Valve, Overhaul
JOB
1
D-039
Sea Strainers - Duplex (All Sizes), Overhaul
JOB
1
D-040
Steering Gear (General) , Overhaul
JOB
1
D-041
Rudder Assembly, Remove, Inspect and Reinstall
JOB
1
D-042
Fin Stabilizers (General), Overhaul
JOB
1
D-043
Grey Water Holding Tanks , Clean and Inspect
JOB
1
D-044
Sewage Holding Tanks , Clean and Inspect
JOB
1
D-045
Grey Water Piping , Clean and Flush
JOB
1
D-046
Sewage Piping , Clean and Flush
JOB
1
O-047
Tanks (Dirty Oil and Waste), Preserve “ 100% ”
JOB
1
O-048
Tanks (Dirty Oil and Waste) , Preserve “ Partial ”
JOB
1
O-049
Tanks ( Grey Water Holding ) , Preserve “ 100% ”
JOB
1
O-050
Tanks ( Grey Water Holding ) , Preserve “ Partial”
JOB
1
O-051
Tanks (Potable Water), Preserve “ 100% ”
JOB
1
O-052
Tanks ( Potable Water ), Preserve “ Partial ”
JOB
1
O-053
Tanks ( Sewage Holding ) , Preserve “ 100% ”
JOB
1
O-054
Tanks ( Sewage Holding ) , Preserve “ Partial ”
JOB
1
D-055
Decks-Exterior, Preserve ("Non-Skid Broadcast Grit" System)
JOB
1
O-056
U/W Body, Preserve “100%”
JOB
1
O-057
U/W Body, Preserve “Partial – Condition A ”
JOB
1
O-058
U/W Body, Preserve “Partial - Condition B”
JOB
1
O-059
U/W Body, Preserve “Partial - Condition C ”
JOB
1
O-060
Stern Tube Interior Surfaces, Preserve 100%
JOB
2
D-061
Hull Plating, Freeboard, Preserve ("Partial)
JOB
1
D-062
Superstructure, Preserve "Partial"
JOB
1
D-063
Cathodic Protection System (Bilge and Sea Chest), Renew
JOB
1
D-064
Cathodic Protection System, Inspect and Maintain
JOB
1
D-065
Drydocking
JOB
1
D-066
Temporary Services, Provide
JOB
1
D-067
Data Service , Provide
JOB
1
D-068
Sea Trial Performance, Provide Support
JOB
1
D-069
Aft Head, Shower Stall, Renew
JOB
1
D-070
Steering Compartment, Insulate
JOB
1
D-071
Battery Space, Install Sound Damping Tiles
JOB
1
D-072
Bulkhead, Interior, Preserve
JOB
1
D-073
Deck, Foundation Mount, HF Antenna , Renew
JOB
1
D-074
Deck Covering (Interior Wet), Renew
JOB
1
D-075
Deck Drains, Interior Renew
JOB
1
D-076
Decks – Exterior Bridge Wings, Blast
JOB
1
D-077
Exhaust Piping, SSDG , Inspect and Repair
JOB
1
D-078
Foot Valves, Renew
JOB
1
D-079
Forward Head, Preserve and Renewal
JOB
1
D-080
Gooseneck Vents, Repair
JOB
1
D-081
Grey Water Pumps and Piping, Install New
JOB
1
D-082
Hull, Side Shell (CPO Head), Preserve
JOB
1
D-083
Hull, Structural, Magazine Locker, Preserve and Insulate
JOB
1
D-084
Hull, Structural, Transverse Frame, Repair
JOB
1
D-085
Hull, Superstructure, Fuel Oil Transfer Station, Repairs
JOB
1
D-086
Joiner Bulkhead Panel, Messdeck Passageway, Renew
JOB
1
D-087
Installation of a Void Box
JOB
1
D-088
Rails, Life Line Stanchion, Renew
JOB
1
D-089
Rudder, Upper Bearing Housing, Renew
JOB
1
D-090
Sea Valves and Waster Pieces , Overhaul or Renew
JOB
1
D-091
Firemain Valves, Overhaul or Renew
JOB
1
D-092
Bilge and Ballast Valves, Overhaul or Renew
JOB
1
D-093
Shelving, Aft Steering, Renew
JOB
1
D-094
Soft Patch Plating, Inspect and Repair (Various Locations)
JOB
1
D-095
Steel Hull and Structural Plating Repairs (7-Pound)
JOB
1
D-096
Steering Tie Rod, Renew
JOB
1
D-097
Stern Flap Repairs - Eroded Weld
JOB
1
D-098
Tanks, Gooseneck Vent and Piping, Renew
JOB
1
D-099
Tanks, Sewage, Structural Repairs
JOB
1
D-100
Through-Deck Packing Gland and Riser, Renew
JOB
1
D-101
Watertight Door, Renew
JOB
1
D-102
Watertight Hatch, Renew
JOB
1
A-O
Composite Labor Rate
Hour
260
B-D
GFP Report
NSP
EA
1
NSP
Z-O
Laydays
Day
5

Total Price of Definite Items

Total Price of Option Items

Total Price of Definite and Optional Items

USCGC Key Biscayne

Performance Period:16MAY2012 to 20JUL2012

ITEM
DESCRIPTION
UNIT PRICE
UNIT
QTY
EXTENDED PRICE
D-001
Hull Plating, U/W Body, Inspect
JOB
1
O-002
Hull Plating (U/W Body), Ultrasonic Testing
500 SHOTS
10
O-003
Perform Steel Hull and Structural Plating Repairs (10-Pound or 10.2-Pound)
4 SQFT
10
O-004
Aluminum Hull and Structural Repairs - 1/4" Plate
4 SQFT
50
O-005
Aluminum Hull and Structural Repairs - 3/16" Plate
4 SQFT
25
O-006
Aluminum Hull and Structural Repairs - 5/16" Plate
4 SQFT
25
O-007
Hull and Structural Plating Repairs -Crack (Aluminum)
1 LF
50
O-008
Hull and Structural Plating Repairs - Crack (Steel)
1 LF
50
O-009
Hull and Structural Plating Repairs - Eroded Weld (Aluminum)
1 LF
50
O-010
Steel Hull and Structural Plating Repairs (5-Pound)
4 SQFT
50
O-011
Steel Hull and Structural Plating Repairs (7.0-Pound, 7.5-Pound or 7.65-Pound)
4 SQFT
50
O-012
Steel Hull and Structural Plating Repairs , Corrugated Plate (4.0-Pound)
4 SQFT
10
O-013
Hull and Structural Plating Repairs (6.0-Pound or 5.63-Pound)
4 SQFT
10
D-014
Appendages (U/W), Leak Test
JOB
1
D-015
Propulsion Shaft Rope Guards , Inspect and Repair
JOB
1
O-016
Appendages (U/W) - Internal, Preserve
JOB
1
D-017
Tanks (MP Fuel Service), Clean and Inspect
JOB
1
D-018
Voids (Non-Accessible), Leak Test
JOB
1
D-019
Tanks (MP Fuel Stowage and Overflow), Clean and Inspect
JOB
1
O-020
Voids (Non-Accessible), Preserve Internal Surfaces
JOB
1
D-021
Tanks, Air Test
JOB
1
D-022
Tanks (Potable Water), Clean and Inspect
JOB
1
D-023
Tanks (Dirty Oil and Waste), Clean and Inspect
JOB
1
D-024
Main Diesel Engine, Renew
JOB
1
D-025
Propulsion Shafting, Remove, Inspect, and Reinstall
JOB
1
D-026
Mechanical Shaft Seal Assemblies, Overhaul
JOB
1
O-027
Propulsion Shaft Bearings (External), Renew
JOB
1
O-028
Propulsion Shaft Stern Tube Bearings, Renew
JOB
1
D-029
Propellers ; Remove, Inspect, and Reinstall
JOB
1
O-030
Propeller , Repair Root Erosion
JOB
1
D-031
MDE Exhaust System , Inspect
JOB
1
D-032
Heat Exchangers , Clean and Inspect
JOB
1
D-033
Ship Service Diesel Generator, Renew
JOB
1
D-034
Fathometer Transducer, Renew
JOB
1
D-035
Fathometer Transducer , General Maintenance
JOB
1
D-036
Speed Doppler, Renew, Doppler Valve, Overhaul
JOB
1
D-037
Sea Strainers - Duplex (All Sizes), Overhaul
JOB
1
D-038
Steering Gear (General) , Overhaul
JOB
1
D-039
Rudder Assembly, Remove, Inspect and Reinstall
JOB
1
D-040
Fin Stabilizers (General), Overhaul
JOB
1
D-041
Grey Water Holding Tanks , Clean and Inspect
JOB
1
D-042
Sewage Holding Tanks , Clean and Inspect
JOB
1
D-043
Grey Water Piping , Clean and Flush
JOB
1
D-044
Sewage Piping , Clean and Flush
JOB
1
O-045
Tanks (Dirty Oil and Waste), Preserve “ 100% ”
JOB
1
O-046
Tanks (Dirty Oil and Waste) , Preserve “ Partial ”
JOB
1
O-047
Tanks ( Grey Water Holding ) , Preserve “ 100% ”
JOB
1
O-048
Tanks ( Grey Water Holding ) , Preserve “ Partial ”
JOB
1
O-049
Tanks (Potable Water), Preserve “ 100% ”
JOB
1
O-050
Tanks ( Potable Water ), Preserve “ Partial ”
JOB
1
O-051
Tanks ( Sewage Holding ) , Preserve “ 100% ”
JOB
1
O-052
Tanks ( Sewage Holding ) , Preserve “ Partial ”
JOB
1
O-053
U/W Body, Preserve “100%”
JOB
1
O-054
U/W Body, Preserve “Partial – Condition A ”
JOB
1
O-055
U/W Body, Preserve “Partial - Condition B”
JOB
1
O-056
U/W Body, Preserve “Partial - Condition C ”
JOB
1
D-057
Cathodic Protection System (Bilge and Sea Chest), Renew
JOB
1
D-058
Cathodic Protection System, Inspect and Maintain
JOB
1
D-059
Drydocking
JOB
1
D-060
Temporary Services, Provide
JOB
1
D-061
Data Service , Provide
JOB
1
D-062
Sea Trial Performance, Provide Support
JOB
1
D-063
Ship Service Diesel Generator Isolation Mounts, Install New
JOB
1
D-064
Sea Valves and Waster Pieces , Overhaul or Renew
JOB
1
D-065
Firemain Valves, Overhaul or Renew
JOB
1
D-066
Bilge and Ballast Valves, Overhaul or Renew
JOB
1
D-067
Deck Covering (Interior ) , Renew
JOB
1
D-068
Electro-Hydraulic Crane, Renew
JOB
1
D-069
Renew Floating Deck System in Aft Berthing
JOB
1
D-070
Forward Head, Preserve
JOB
1
D-071
Forward Peak Compartment, Preserve
JOB
1
D-072
Insulation, Overhead, CO’s and XO’s Stateroom, Renew
JOB
1
D-073
Joiner Bulkhead Panels, CPO Passageway, Renew
JOB
1
D-074
Joiner Bulkhead Panels, Messdeck Passageway, Galley Renew
JOB
1
D-075
Main Mast, Preserve
JOB
1
D-076
Piping, Potable Water Brominator , Renew
JOB
1
D-077
Racks and Lockers, Renew
JOB
1
D-078
Stern Tubes, Renew
JOB
1
D-079
Structural Closures , Renew
JOB
1
D-080
Superstructure, F/O Transfer Station, Repairs
JOB
1
D-081
Ventilation Ducting, CO and XO Staterooms, EM Locker, Renew
JOB
1
D-082
Fin Stabilizers, Bearing Housings, Renew
JOB
1
D-083
Sewage Holding Tank Renew Vent Pipe
JOB
1
A-O
Composite Labor Rate
Hour
250
B-D
GFP Report
NSP
EA
1
NSP
Z-O
Laydays
Day
5

Total Price of Definite Items

Total Price of Option Items

Total Price of Definite and Optional Items

USCGC Drummond

Performance Period: 08AUG2012 to 23NOV2012

ITEM
DESCRIPTION
UNIT PRICE
UNIT
QTY
EXTENDED PRICE
D-001
Hull Plating, U/W Body, Inspect
JOB
1
O-002
Hull Plating (U/W Body), Ultrasonic Testing
500 SHOTS
10
O-003
Perform Steel Hull and Structural Plating Repairs (10-Pound or 10.2-Pound)
4 SQFT
10
O-004
Aluminum Hull and Structural Repairs - 1/4" Plate
4 SQFT
50
O-005
Aluminum Hull and Structural Repairs - 3/16" Plate
4 SQFT
25
O-006
Aluminum Hull and Structural Repairs - 5/16" Plate
4 SQFT
25
O-007
Hull and Structural Plating Repairs -Crack (Aluminum)
1 LF
50
O-008
Hull and Structural Plating Repairs - Crack (Steel)
1 LF
50
O-009
Hull and Structural Plating Repairs - Eroded Weld (Aluminum)
1 LF
50
O-010
Steel Hull and Structural Plating Repairs (5-Pound)
4 SQFT
50
O-011
Steel Hull and Structural Plating Repairs (7.0-Pound, 7.5-Pound or 7.65-Pound)
4 SQFT
50
O-012
Steel Hull and Structural Plating Repairs , Corrugated Plate (4.0-Pound)
4 SQFT
10
O-013
Hull and Structural Plating Repairs (6.0-Pound or 5.63-Pound)
4 SQFT
10
D-014
Appendages (U/W), Leak Test
JOB
1
O-015
Appendages (U/W) - Internal, Preserve
JOB
1
D-016
Tanks (MP Fuel Service), Clean and Inspect
JOB
1
D-017
Voids (Non-Accessible), Leak Test
JOB
1
D-018
Tanks (MP Fuel Stowage and Overflow), Clean and Inspect
JOB
1
0-019
Voids (Non-Accessible), Preserve Internal Surfaces
JOB
1
D-020
Tanks, Air Test
JOB
1
D-021
Tanks (Potable Water), Clean and Inspect
JOB
1
D-022
W/I DELETED
JOB
1
D-023
Tanks (Dirty Oil and Waste), Clean and Inspect
JOB
1
O-024
Propulsion System, Alignment Check
JOB
1
D-025
Propulsion Shafting, Remove, Inspect, and Reinstall
JOB
1
D-026
Mechanical Shaft Seal Assemblies, Overhaul
JOB
1
D-027
W/I DELETED
JOB
1
O-028
Propulsion Shaft Bearings (External), Renew
JOB
1
O-029
Propulsion Shaft Stern Tube Bearings, Renew
JOB
1
D-030
Propellers; Remove, Inspect, and Reinstall
JOB
1
O-031
Propeller, Repair Root Erosion
JOB
1
D-032
Exhaust System, MDE, Inspect
JOB
1
D-033
Heat Exchangers, Clean and Inspect
JOB
1
D-034
Ship Service Diesel Generator, Renew
JOB
1
D-035
Fathometer Transducer, Renew
JOB
1
D-036
Fathometer Transducer, General Maintenance
JOB
1
D-037
Speed Doppler, Renew, Doppler Valve, Overhaul
JOB
1
D-038
Sea Strainers - Duplex (All Sizes), Overhaul
JOB
1
D-039
Steering Gear (General), Overhaul
JOB
1
D-040
Rudder Assembly, Remove, Inspect and Reinstall
JOB
1
D-041
Fin Stabilizers (General), Overhaul
JOB
1
D-042
Grey Water Holding Tanks, Clean and Inspect
JOB
1
D-043
Sewage Holding Tanks, Clean and Inspect
JOB
1
D-044
Grey Water Piping, Clean and Flush
JOB
1
D-045
Sewage Piping, Clean and Flush
JOB
1
D-046
Battery Space, Preserve and Insulate
JOB
1
D-047
Aft Steering Compartment, Preserve and Insulate
JOB
1
O-048
Tanks (Dirty Oil and Waste), Preserve “ 100% ”
JOB
1
O-049
Tanks (Dirty Oil and Waste), Preserve “ Partial ”
JOB
1
O-050
Tanks (Grey Water Holding), Preserve “ 100% ”
JOB
1
O-051
Tanks (Grey Water Holding), Preserve “ Partial ”
JOB
1
O-052
Tanks (Potable Water), Preserve “ 100% ”
JOB
1
O-053
Tanks (Potable Water), Preserve “ Partial ”
JOB
1
O-054
Tanks (Sewage Holding), Preserve “ 100% ”
JOB
1
O-055
Tanks (Sewage Holding), Preserve “ Partial ”
JOB
1
O-056
Accessible Void(s), Preserve “ 100% ”
JOB
1
O-057
Accessible Void(s), Preserve “ Partial ”
JOB
1
D-058
Decks - Exterior, Preserve (“ Non-Skid Broadcast Grit” System)
JOB
1
D-059
U/W Body, Preserve (“100%”) Used with Side Scan
JOB
1
D-060
Hull Plating Freeboard, Preserve (“100%”) Used with Side Scan
JOB
1
D-061
Superstructure, Preserve “ Partial ”
JOB
1
D-062
Cathodic Protection System (Bilge and Sea Chest), Renew
JOB
1
D-063
Cathodic Protection System, Inspect and Maintain
JOB
1
D-064
Drydocking
JOB
1
D-065
Temporary Services, Provide
JOB
1
D-066
Data Service, Provide
JOB
1
D-067
Sea Trial Performance, Provide Support
JOB
1
D-068
Fire Suppression System, Upgrade
JOB
1
D-069
Sea Valves and Waster Pieces, Overhaul or Renew
JOB
1
D-070
Firemain Valves, Overhaul Or Renew
JOB
1
D-071
Bilge and Ballast Valves, Overhaul or Renew
JOB
1
D-072
Bilge Surfaces, Engine room, Preserve
JOB
1
D-073
Deck, Foundation Mount, Loudhailer, Renew
JOB
1
D-074
Deck, (Interior) CPO Stateroom, Repair
JOB
1
D-075
Deck Drains, Interior, Renew
JOB
1
D-076
Forward Void, Repair and Preserve
JOB
1
D-077
Hull, Interior Bulkheads, Preserve
JOB
1
D-078
Hull, Structural Closures, Renew
JOB
1
D-079
Hull, Superstructure, F/O Transfer Station, Repairs
JOB
1
D-080
Hull and Structural Repairs – Transom Mounted Rung Ladder
JOB
1
D-081
Hull Structural, Bulkhead, Aft Head , Preserve and Insulate
JOB
1
D-082
Insulation, Bulkhead/Overhead, Renew
JOB
1
D-083
Life Lines, Anchor Points, Renew
JOB
1
D-084
Main Deck, Athwart Ship’s Passage Way, Repair
JOB
1
D-085
Main Mast, Fabricate and Install New Canopy
JOB
1
D-086
Main Mast, Preserve
JOB
1
D-087
Perform Structural Repairs – Forward Inaccessible Void , Wastage and Installation of a Void Box
JOB
1
D-088
Piping, Air Conditioning , Renew
JOB
1
D-089
Piping, Bilge System, Forward Void, Repair
JOB
1
D-090
Piping, SSDG Raw Water , Repairs
JOB
1
D-091
Racks and Lockers, Renew
JOB
1
D-092
Rudders, Lower Bearing Housing , Renew
JOB
1
D-093
Sewage Piping, Renew
JOB
1
D-094
Stern Tubes, Renew
JOB
1
D-095
Structural Repairs – Bridge Windows Drainage Piping, Renew
JOB
1
D-096
Tank, Hydro Pneumatic, Foundation Repairs
JOB
1
D-097
Tank Level Indicators, Sewage, Potable Water, Fuel Oil Tanks, Renew
JOB
1
D-098
Tank (MP Center Fuel ), Inspect and Repair
JOB
1
D-099
Tanks, Grey Water, Dirty Oil, Oily Water, Renew
JOB
1
D-100
Tanks, Potable Water, Repair and Preserve
JOB
1
D-101
Through-Deck Packing Glands, Renew
JOB
1
D-102
Vent Pipe, Renew
JOB
1
D-103
Windows, CO and XO Stateroom , Renew
JOB
1
D-104
Joiner Bulkhead Panels, Renew
JOB
1
A-O
Composite Labor Rate
Hour
260
B-D
GFP Report
NSP
EA
1
NSP
Z-O
Laydays
Day
5

Total Price of Definite Items

Total Price of Option Items

Total Price of Definite and Optional Items

Total Price of Definite and Optional Items for USCGC’s Kodiak Island, Key Biscayne and Drummond

CONTRACT CLAUSES

(1) FAR 52.212-4 CONTRACT TERMS AND CONDITIONS – COMMERCIAL ITEMS (Jun 2010)

ADDENDUM

FAR 52.204-1 APPROVAL OF CONTRACT (DEC 1989)

This contract is subject to the written approval of the Branch Chief, CPD, C&P1 and shall not be binding until so approved.

FAR 52.209-7 – Information Regarding Responsibility Matters. (Jan 2011)

(a) Definitions. As used in this provision—

“Administrative proceeding” means a non-judicial process that is adjudicatory in nature in order to make a determination of fault or liability (e.g., Securities and Exchange Commission Administrative Proceedings, Civilian Board of Contract Appeals Proceedings, and Armed Services Board of Contract Appeals Proceedings). This includes administrative proceeding at the Federal and State level but only in connection with performance of a Federal contract or grant. It does not include agency actions such as contract audits, site visits, corrective plans, or inspection of deliverables.

“Federal contracts and grants with total value greater than $10,000,000” means—

(1) The total value of all current, active contracts and grants, including all priced options; and

(2) The total value of all current, active orders including all priced options under indefinite-delivery, indefinite-quantity, 8(a), or requirements contracts (including task and delivery and multiple-award Schedules).

“Principal” means an officer, director, owner, partner, or a person having primary management or supervisory responsibilities within a business entity (e.g., general manager; plant manager; head of a division or business segment; and similar positions).

(b) The offeror [_] has [_] does not have current active Federal contracts and grants with total value greater than $10,000,000.

(c) If the offeror checked “has” in paragraph (b) of this provision, the offeror represents, by submission of this offer, that the information it has entered in the Federal Awardee Performance and Integrity Information System (FAPIIS) is current, accurate, and complete as of the date of submission of this offer with regard to the following information:

(1) Whether the offeror, and/or any of its principals, has or has not, within the last five years, in connection with the award to or performance by the offeror of a Federal contract or grant, been the subject of a proceeding, at the Federal or State level that resulted in any of the following dispositions:

(i) In a criminal proceeding, a conviction.

(ii) In a civil proceeding, a finding of fault and liability that results in the payment of a monetary fine, penalty, reimbursement, restitution, or damages of $5,000 or more.

(iii) In an administrative proceeding, a finding of fault and liability that results in—

(A) The payment of a monetary fine or penalty of $5,000 or more; or

(B) The payment of a reimbursement, restitution, or damages in excess of $100,000.

(iv) In a criminal, civil, or administrative proceeding, a disposition of the matter by consent or compromise with an acknowledgment of fault by the Contractor if the proceeding could have led to any of the outcomes specified in paragraphs (c)(1)(i), (c)(1)(ii), or (c)(1)(iii) of this provision.

(2) If the offeror has been involved in the last five years in any of the occurrences listed in (c)(1) of this provision, whether the offeror has provided the requested information with regard to each occurrence.

(d) The offeror shall post the information in paragraphs (c)(1)(i) through (c)(1)(iv) of this provision in FAPIIS as required through maintaining an active registration in the Central Contractor Registration database at http://www.ccr.gov (see 52.204-7).

(End of provision)

52.209-9 – Updates of Publicly Available Information Regarding Responsibility Matters (Jan 2011)

(a) The Contractor shall update the information in the Federal Awardee Performance and Integrity Information System (FAPIIS) on a semi-annual basis, throughout the life of the contract, by posting the required information in the Central Contractor Registration database at http://www.ccr.gov .

(b)

(1) The Contractor will receive notification when the Government posts new information to the Contractor’s record.

(2) The Contractor will have an opportunity to post comments regarding information that has been posted by the Government. The comments will be retained as long as the associated information is retained, i.e., for a total period of 6 years. Contractor comments will remain a part of the record unless the Contractor revises them.

(3)

(i) Public requests for system information posted prior to April 15, 2011, will be handled under Freedom of Information Act procedures, including, where appropriate, procedures promulgated under E.O. 12600.

(ii) As required by section 3010 of Public Law 111-212, all information posted in FAPIIS on or after April 15, 2011, except past performance reviews, will be publicly available.

(End of clause)

(3) FAR 52.217-7 OPTION FOR INCREASED QUANTITY – SEPARATELY PRICED LINE ITEM (MAR 1989) - VARIATION The Government may require the performance of the numbered line items, identified in the Schedule as option items, at the unit prices stated in the Schedule. The option quantities shown in the Schedule are estimates only. The Government has the right to require performance of these items at the quantities deemed necessary. Therefore, the Government may exercise an option item on more than one occasion during the contract performance period. The Contracting Officer will provide initial notification of the exercise of an option either verbally, by facsimile, or both. When time is of essence initial notification will be provided verbally followed within 24 hours by a facsimile of confirmation. A contract modification will be executed shortly thereafter to include those options wherein exercise notification was provided. Such options may be exercised at any phase during the contract performance period as stated herein, or any extension of the performance period. To maintain the contract performance period the Contractor shall commence performance of an option item immediately upon receiving initial notification; but, not later than 24 hours thereafter, unless proper sequencing of the work requires a delay in beginning performance of the option. In that case, the option item shall be commenced as soon as proper sequencing permits. The exercise of any option item listed in the Schedule will not normally extend the contract performance period. However, the Contracting Officer may consider a request by the Contractor for contract extension if an option is exercised after 50% of the contract performance period has expired.

(End of Clause)

HSAR 3052.209-7 PROHIBITION ON CONTRACTS WITH CORPORATE EXPATRIATES

(JUN 2006)

(a) Prohibitions.

Section 835 of the Homeland Security Act, 6 U.S.C. 395, prohibits the Department of Homeland Security from entering into any contract with a foreign incorporated entity which is treated as an inverted domestic corporation as defined in this clause, or with any subsidiary of such an entity. The Secretary shall waive the prohibition with respect to any specific contract if the Secretary determines that the waiver is required in the interest of national security.

(b) Definitions. As used in this clause:

Expanded Affiliated Group means an affiliated group as defined in section 1504(a) of the Internal Revenue Code of 1986 (without regard to section 1504(b) of such Code), except that section 1504 of such Code shall be applied by substituting `more than 50 percent' for `at least 80 percent' each place it appears.

Foreign Incorporated Entity means any entity which is, or but for subsection (b) of section 835 of the Homeland Security Act, 6 U.S.C. 395, would be, treated as a foreign corporation for purposes of the Internal Revenue Code of 1986.

Inverted Domestic Corporation. A foreign incorporated entity shall be treated as an inverted domestic corporation if, pursuant to a plan (or a series of related transactions)—

(1) The entity completes the direct or indirect acquisition of substantially all of the properties held directly or indirectly by a domestic corporation or substantially all of the properties constituting a trade or business of a domestic partnership;

(2) After the acquisition at least 80 percent of the stock (by vote or value) of the entity is held—

(i) In the case of an acquisition with respect to a domestic corporation, by former shareholders of the domestic corporation by reason of holding stock in the domestic corporation; or

(ii) In the case of an acquisition with respect to a domestic partnership, by former partners of the domestic partnership by reason of holding a capital or profits interest in the domestic partnership; and

(3) The expanded affiliated group which after the acquisition includes the entity does not have substantial business activities in the foreign country in which or under the law of which the entity is created or organized when compared to the total business activities of such expanded affiliated group.

Person, domestic, and foreign have the meanings given such terms by paragraphs (1), (4), and (5) of section 7701(a) of the Internal Revenue Code of 1986, respectively.

(c) Special rules. The following definitions and special rules shall apply when determining whether a foreign incorporated entity should be treated as an inverted domestic corporation.

(1) Certain stock disregarded. For the purpose of treating a foreign incorporated entity as an inverted domestic corporation these shall not be taken into account in determining ownership:

(i) Stock held by members of the expanded affiliated group which includes the foreign incorporated entity; or

(ii) Stock of such entity which is sold in a public offering related to an acquisition described in section 835(b)(1) of the Homeland Security Act, 6 U.S.C. 395(b)(1).

(2) Plan deemed in certain cases. If a foreign incorporated entity acquires directly or indirectly substantially all of the properties of a domestic corporation or partnership during the 4-year period beginning on the date which is 2 years before the ownership requirements of subsection (b)(2) are met, such actions shall be treated as pursuant to a plan.

(3) Certain transfers disregarded. The transfer of properties or liabilities (including by contribution or distribution) shall be disregarded if such transfers are part of a plan a principal purpose of which is to avoid the purposes of this section.

(d) Special rule for related partnerships. For purposes of applying section 835(b) of the Homeland Security Act, 6 U.S.C. 395(b) to the acquisition of a domestic partnership, except as provided in regulations, all domestic partnerships which are under common control (within the meaning of section 482 of the Internal Revenue Code of 1986) shall be treated as a partnership.

(e) Treatment of Certain Rights.

(1) Certain rights shall be treated as stocks to the extent necessary to reflect the present value of all equitable interests incident to the transaction, as follows:

(i) warrants;

(ii) options;

(iii) contracts to acquire stock;

(iv) convertible debt instruments; and

(v) others similar interests.

(2) Rights labeled as stocks shall not be treated as stocks whenever it is deemed appropriate to do so to reflect the present value of the transaction or to disregard transactions whose recognition would defeat the purpose of Section 835.

(f) Disclosure. The offeror under this solicitation represents that [Check one]:

__ it is not a foreign incorporated entity that should be treated as an inverted domestic corporation pursuant to the criteria of (HSAR) 48 CFR 3009.108-7001 through 3009.108-7003;

__ it is a foreign incorporated entity that should be treated as an inverted domestic corporation pursuant to the criteria of (HSAR) 48 CFR 3009.108-7001 through 3009.108-7003, but it has submitted a request for waiver pursuant to 3009.108-7004, which has not been denied; or

__ it is a foreign incorporated entity that should be treated as an inverted domestic corporation pursuant to the criteria of (HSAR) 48 CFR 3009.108-7001 through 3009.108-7003, but it plans to submit a request for waiver pursuant to 3009.108-7004.

(g) A copy of the approved waiver, if a waiver has already been granted, or the waiver request, if a waiver has been applied for, shall be attached to the bid or proposal.

(End of provision)

(4) FAR 52.252-2 CLAUSES INCORPORATED BY REFERENCE (FEB 1998)

This contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at this address: http://www.arnet.gov/far/index.html

FAR 52.211-15
Defense Priority and Allocation Requirements (APR 2008) DO A3 Rating
FAR 52.223-3
Hazardous Material Identification and Material Safety Data (JAN 1997)

Alternate I (JUL 1995)

FAR 52.223-12
Refrigeration Equipment and Air Conditioners (MAY 1995)
FAR 52.228-5
Insurance – Work on a Government Installation (JAN 1997)
FAR 52.232-18
Availability of Funds (APR 1984)
FAR 52.242-2
Production Progress Reports (APR 1991)
FAR 52.245-1
Government Property (AUG 2010)
FAR 52.245-9
Use and Charges (AUG 2010)
HSAR 3052.211-70
Index for Specifications (DEC 2003)
HSAR 3052.217-90
Delivery and Shifting of Vessel (DEC 2003)
HSAR 3052.217-91
Performance (DEC 2003)
HSAR 3052.217-92
Inspection and Manner of Doing Work (DEC 2003)
HSAR 3052.217-93
Subcontracts (DEC 2003)
HSAR 3052.217-94
Lay Days (DEC 2003)
HSAR 3052.217-95
Liability and Insurance (DEC 2003)
HSAR 3052.217-96
Title (DEC 2003)
HSAR 3052.217-97
Discharge of liens (DEC 2003)
HSAR 3052.217-98
Delays (DEC 2003)
HSAR 3052.217-99
Department of Labor Safety and Health Regulations for Ship Repair (DEC 2003)
HSAR 3052.217-100
Guarantee (JUN 2006)
HSAR 3052.222-70
Strikes or Picketing Affecting Timely Completion of the Contract Work (DEC 2003)
HSAR 3052.222-71
Strikes or Picketing Affecting Access to a DHS Facility (DEC 2003)
HSAR 3052.223-90
Accident and Fire Reporting (DEC 2003)
HSAR 3052.242-71
Dissemination of Contract Information (DEC 2003)
HSAR 3052.242-72
Contracting Officer’s Technical Representative (DEC 2003)
HSAR 3052.245-70
Government Property Reports (AUG 2008) [Deviation])

(5) HSAR 3052.223-70 REMOVAL OR DISPOSAL OF HAZARDOUS SUBSTANCES – APPLICABLE LICENSES AND PERMITS (JUN 2006)

The Contractor shall have all licenses and permits required by Federal, state, and local laws to perform hazardous substance(s) removal or disposal services. If the Contractor does not currently possess these documents, it shall obtain all requisite licenses and permits within [“insert days”] days after date of award. The Contractor shall provide evidence of said documents to the Contracting Officer or designated Government representative prior to commencement of work under the contract.

(End of clause)

(6) HAZARDOUS WASTE

Contractors performing dockside ship repair work at Government facilities are required to comply with FAR 52.223-3, Hazardous Material Identification and Material Safety Data (JAN 1997) Alt I, the U.S. Coast Guard shipboard hazardous waste policy, as prescribed in COMDINST M16478.1B, and MLCA standard specifications. Disposal of all hazardous wastes shall be performed by the Contractor and the Contractor shall meet all federal and state requirements. The Contractor is also required to submit an acceptable hazardous waste management plan to the Port Engineer at the Arrival Conference. The plan will be reviewed by the facility hazardous waste manager. An acceptable plan must address, at a minimum, the following requirements:

(a) EPA and local authority hazardous waste generator ID numbers or registration of the Contractors, his transporters, and disposal facilities (TSDFs);

(b) An inventory of all hazardous chemicals, compounds and other agents brought aboard the facility accompanied by their respective Material Safety Data Sheets;

(c) A list of all anticipated hazardous wastes to be generated and a federal/state/local regulation cross reference list for those wastes;

(d) Waste collection and containment procedures;

(e) A hazardous material spill and cleanup plan including tools and materials that will be on hand and readily available to facility containment and cleanup;

(f) Training certification for the Contractor's hazardous waste manager.

The Contractor shall note the local environmental regulations in Boston, and for Boston Harbor, are more stringent than in many jurisdictions. As with all environmental regulations, it is the Contractor's responsibility to research, prepare for, and comply with, the local and state regulations.

All waste generated under the performance of this contract shall be disposed under ISC Boston's EPA hazardous waste generator ID number. The Contractor shall notify the Contracting Officer's Technical Representative (COTR) 24 hours prior to any waste removals, and ensure that waste removals are conducted during normal business hours (0800-1600) on Monday through Friday (excluding holidays). All hazardous waste manifests shall be reviewed and signed by ISC Boston hazardous waste personnel. The point of contact for environmental issues is the Environmental Protection Specialist at ISC Boston (617)223-3387.

(7) VOLATILE ORGANIC COMPOUNDS (VOC) REGULATIONS

(a) Contractors are required to comply with federal, state and local VOC compliance laws and regulations. Among other requirements, certain Contractors may also be required to operate pursuant to a Title V permit. The need for such a permit will depend on the provisions of the applicable state’s “State Implementation Plan” (SIP) and the type/quantity of the Contractor’s regulated emissions, including VOCs. Certain SIPs may also mandate certain Contractors to operate under the terms of a compliance plan intended to reduce VOC emissions.

(b) Contractors, therefore, must submit the following to the designated Port Engineer not later than two weeks after contract award:

1) Copies of any federal, state or local permits required and applicable to the use or application of VOCs at Contractor’s facility or offsite work places;

2) Copies of any compliance plans required and applicable to the use or application of VOCs at Contractor’s facility or offsite work places.

(c) If no federal, state or local permits or compliance plans are required and applicable to the use or application of VOCs at Contractor’s facility or offsite workplaces, then Contractor shall submit to the designated Port Engineer a letter, notarized under oath, that such documents are not required.

(d) Contractors will submit the following to the designated Port

Engineer not later than two weeks after contract award: Data Sheets (MSDS) documents, certificates, specifications or any other manufacturing data verifying the VOC ratings of paints to be applied to the Cutter in accordance with MLCA Standard Spec 63000N, Section 5.3.1.

(8) TELEPHONE CHARGE

The Commanding Officer of the Cutter will pay all toll charges and applicable taxes and surcharges for long-distance telephone calls placed by ship’s personnel. All other charges shall be borne by the Contractor.

(9) ACCESSIBILITY OF CONTRACTOR'S FACILITY

The Contractor shall provide a facility accessible from a navigable waterway at which a ship of the characteristics described in the attached specification can, using its own propulsion, safely arrive, lie afloat and depart at all states of the tide and at any time day or night. The facility and its approaches shall have a minimum water depth of 10 feet and a minimum vertical clearance of 58 feet.

(10) REQUIRED INSURANCE

The Contractor shall, at its own expense, procure and maintain the following kinds of insurance with respect to performance under the contract. In accordance with HSAR 3052.228-70, Insurance (DEC 2003), the Contractor shall furnish the Contracting Officer with proof of insurance for the duration of the contract, including:

1. Ship Repairer's Liability - $500,000 per occurrence.

2. Comprehensive General Liability - $500,000 per occurrence.

3. Full insurance coverage in accordance with the United States’ Longshoremen's and Harbor Worker's Act.

4. Full insurance coverage in accordance with the State's Workmen's Compensation Law (or its equivalent) for all places of performance under this contract.

The insurance certificate must provide the name of the US Coast Guard vessel and the contract and/or solicitation number as specifically insured.

(11) ACCESS TO VESSEL

(a) A reasonable number of officers, employees, and associates of the Government, or other Prime Contractors with the Government, and their subcontractors, shall, as authorized by the Contracting Officer, have, at all reasonable times, admission to the plant, and access to vessel(s) to perform and fulfill their respective obligations to the Government on a noninterference basis.

The Contractor shall make reasonable arrangements with the Government or Contractors of the Government, as shall have been identified and authorized by the Contracting Officer, to be given admission to the Contractor's facilities and access to the vessel(s) and to office space, work areas, storage or shop areas, or other facilities and services, necessary for the performance of their respective responsibilities and reasonable to their performance. All such above personnel shall be required to comply with all Contractor rules and regulations governing personnel at its shipyard, including those relative to safety and security.

(b) The Contractor further agrees, as authorized by the Contracting Officer, to afford to a reasonable number of officers, employees, and associates of bidders on other contemplated work, the same privileges of admission to the Contractor's plant and access to the vessel(s) on a noninterference basis subject to all Contractor rules and regulations governing personnel in its shipyard, including those relative to safety and security.

(12) INDEMNIFICATION FOR ACCESS TO VESSELS

Notwithstanding any provision in the "Access to Vessels" clause, or any other clause of the contract, the Contractor agrees to allow officers, employees, and associates of the Government, or other Prime Contractors with the Government and their subcontractors, and officers, employees, and associates of quoters on other…

This is the start of the file's text. The full file is on GovTribe.

File details come from the government source that posted it. Updated .