af tech manual directive.doc

TM-86-01K.1 1 December 2005

TM-86-01N 1 April 2009 TM-86-01N 1 April 2009

Air Force Technical Manual Contract Requirements (TMCR) for

AN/FMQ-19 Automatic Meteorological Station (AMS)

ATTACHMENT TO CDRL SEQUENCE NUMBER A006, EXHIBIT A

REQUEST FOR PROPOSAL/CONTRACT: FA8217-12-R-5006

4 October 2011 Section 1. Technical Order (TO) Program Requirements

1. TMCR Tailoring. Offerors must tailor this TMCR document, including the associated tables, matrices and Specification/Standard Interface Records (SIRs). The tailored TMCR shall be attached to the CDRL for TO delivery, and shall be included in the proposal as a separate exhibit, referenced in the proposal PWS. Air Force TO Acquisition procedures, including procedures for tailoring this document, are found in TO 00-5-3. Any terms or procedures found in this document may be researched there.

2. TO Program Scope. The offeror shall tailor Section 2 to propose the TO types (Table 1) and source data, TO updates, commercial manuals, and TOs prepared to Non Government Standards (NGS) (Table 2) required to support the FMQ-19 program’s objectives.

3. Commercial Manuals. Offerors shall propose the use of existing commercial manuals to the maximum extent possible without impairing program support objectives. The proposal will describe the method used to recommend and submit specific manuals to the government for review and approval. NOTES: a) Contractors may use Data Item Description (DID) DI-TMSS-80067, Technical Manual (TM) Contractor Furnished Aeronautical Equipment or Contractor Furnished Equipment (CFAE/CFE) Notices (located at http://dodssp.daps.dla.mil/assist.htm), to provide recommendation data. b) Government activities will use MIL-PRF-32216, Evaluation of Commercial Off-The-Shelf (COTS) Manuals and Preparation of Supplemental Data, as a guide for review and acceptance of all recommended commercial manuals.

5. Subsequent TO/Data Requirements. Offerors shall propose a process for notifying the government when additional TO or source data requirements are identified subsequent to contract award. This process shall require government review and approval of recommended additional requirements prior to contractual approval. NOTE: The recommended notification process is to use CFAE/CFE Notices (DI-TMSS-80067).

6. TO Development. The offeror shall propose TO development practices and procedures that ensure TOs and data are compatible with the Air Force Technical Order Concept of Operations (CONOPS) (on the AF Portal at https://wwwd.my.af.mil/afknprod/DocView.asp?DocID=1689861) and the Enhanced Technical Information Management System (ETIMS). In addition, TOs shall be written to a scope and depth of coverage sufficient to support the operations and maintenance concepts, and to the Reading Grade Level (RGL) specified in MIL-STD-38784.

7. TO Numbering. Offerors shall notify the government of manuals which require TO numbers. TO numbers are not required for manuals to be used exclusively by the offeror’s own personnel. (NOTE: DI-TMSS-80067 may be used to provide the notification.) AF procedures for numbering TOs are described in TO 00-5-3 and TO 00-5-18.

8. Data Rights. Government rights in data are specified in the Defense Federal Acquisition Regulation Supplement (DFARS), paragraphs 227-7102 through 227-7104. Offerors shall propose Unlimited Rights for all source data and TOs prepared specifically for the contract.

8.1. If some TOs or source data are copyrighted or contain proprietary data or procedures, offerors may propose Limited Rights or Government Purpose Rights (GPR) only. Proposed commercial manuals should be provided with Unlimited Rights. Copyrights shall be according to DFARS paragraphs 227-7103, 7105 or 7106.

8.2. Specifically, if an NGS is proposed, the government shall be given unlimited rights for all business rules (tailoring and application methods and procedures) and documented business processes developed for use in TO development. Government data rights shall extend to the common source database, transformation style sheets, and other tools or products used to author or display NGS technical data.

9. Classification, Distribution, Destruction, Disclosure, and Export Control Notices. Offerors shall determine the correct markings and controls for classified and restricted distribution data and TOs IAW the program’s Security Classification Guide (SCG) and DOD 5200.1-R, DODD 5230.24, AFIs 21-303, 31-401 and 61-204, and MIL-STD-38784 (available at http://www.e-publishing.af.mil/ or http://dodssp.daps.dla.mil/assist.htm). The markings and notices shall be reviewed during In-Process Reviews (IPR). NOTE: Distribution limitations will be determined on a case-by-case basis as TOs are developed, dependent upon TO content.

10. TO Quality. Offerors shall propose a quality assurance program which ensures TOs are prepared IAW this contract. Recommended QA methods must include actual performance of procedures and use of desk-top analysis for non-procedural data. Simulation (walk-through/talk-through) should be reserved for those procedures which would present a hazard to personnel or equipment. Offerors’ proposals shall describe how the government will be allowed to interact with the contractor’s TO development team.

10.1. Conferences and Technical Reviews. Offerors shall propose sufficient conferences and reviews to allow insight into TO development processes and ensure contract compliance. Offerors should host an initial Guidance Conference or Technical Interchange Meeting (TIM) within two weeks of contract award to ensure mutual understanding of TO contract requirements, schedules, points of contact, etc. Periodic In-Process Reviews (IPRs) and Prepublication Reviews (PPR) ensure TOs are being developed according to contract requirements and that open discrepancies are cleared prior to publication.

10.2. TO Verification. Offerors shall propose their method for documenting verification that TO procedures are accurate, adequate, current, safe and usable for their intended purposes. Offerors shall notify the government at least 180 days prior of the need for any Government Furnished Information/Government Furnished Equipment (GFI/GFE) required to perform verification tasks.

10.3. Validation Support. Offerors shall propose the methods, equipment and personnel required to support government TO Validation. This support should consist of at least technical support to resolve problems during verification, program-peculiar equipment and supplies, maintenance of TO configuration, and incorporation of Government comments.

10.4. Technical Data Assessment (TDA – originally called First Article Testing). The contractor shall deliver a representative percentage of Indexed Portable Document Format (IPDF) TO files to verify indexing compliance with the Technical Order Conversion Requirements (TOCR) (on the AF Portal at https://wwwd.my.af.mil/afknprod/DocView.asp?DocID=5153963).

11. TO and Source Data Maintenance. Offerors shall propose methods for maintaining accuracy, currency and configuration of TOs and source data throughout the contract period of performance. Maintenance includes preparation of TO and source data updates to incorporate corrections, equipment configuration changes, and maintenance and operational concept changes.

12. TO Delivery. Offerors shall propose practices and procedures for secure access to or delivery of digital TO files, including those for Preliminary TOs (PTOs), source data, reproduction masters, and program support data. Practices and procedures shall be compatible with the program’s IDS (found in (specify RFP location of IDS)). TO file delivery formats shall be according to applicable CDRLs and the tailored TM Delivery Requirements Matrices included in Section 2 of this document. Paper TO delivery is not acceptable for final delivery of TOs.

12.1. Indexed Adobe™ Portable Document Format (IPDF) Files. The contractor shall validate indexing of PDF TO files using the specifications contained in the Technical Order Conversion Requirements (TOCR) found on the Air Force Portal at https://wwwd.my.af.mil/afknprod/DocView.asp?DocID=5153963.

13. Schedules. Offerors shall include TO program events and schedules in their proposed Integrated Master Plan (IMP) and Integrated Master Schedule (IMS), and update the IMS throughout the period of performance. NOTE: AF policy requires delivery of verified TOs prior to or concurrently with delivery of operational equipment to the field (AFI 21-303, Technical Orders). This policy will determine TO development and delivery schedules throughout the acquisition phase of a program.

14. Time Compliance Technical Orders (TCTOs). Offerors shall propose practices and procedures to develop AF TCTOs and related TO updates when tasked as part of the approval process for Engineering Change Proposals (ECPs) to configured items. Costs for TCTO package development must be included in ECP Costs – not included as direct proposal costs. NOTE: ECPs are reviewed and approved by the Government’s Configuration Control Board (CCB). When the CCB decides that a TCTO is the appropriate method of implementation, the contractor may be requested to develop the TCTO package for Air Force coordination and approval. See TO 00-5-15, Air Force Time Compliance Technical order Process, (available at http://www.tinker.af.mil/library/factsheets/factsheet.asp?id=6082/00-5-15-WA-1/00-5-15.PDF) for a detailed description of TCTO processes.

Section 2. TM Type and Delivery Requirements

NOTES:

· Mark the TM Type Selection Tables indicating the applicable TO types and related specifications. For additional interface requirements see the program-specific Government Concept of Operations (GCO).

· All page-based TOs developed under this contract must conform to the general style and format requirements of MIL-STD-38784; IETMs must conform to S1000D and its business rules.

· Check the ASSIST database, http://dodssp.daps.dla.mil/assist.htm, for updated versions of the required TMSS prior to initiating any work on this proposal/contract.

· Manuals delivered using this table and DI-TMSS-80067, CFAE/CFE Notices, must be reviewed and approved by the Air Force prior to delivery.

· IPBs are developed IAW MIL-PRF-38807, except that MIL-DTL-87929 will also be used for IPBs combined with work packages.

· All checklists, except aircrew and nuclear weapons checklists, are developed IAW MIL-PRF-5096.

· MIL-PRF-83495 requires MIL-HDBK-863 to be levied on engineering data for preparation of end item wiring data and schematic diagrams.

· Delivery requirements are indicated in the TM Delivery Requirements matrices.

Part A – TM Type Selection Tables.

Table 1 TMSS Requirements for the (AN/FMQ19) Program

a. Inspection and Maintenance Requirements (-6) Manual

FORMCHECKBOX

b. Acceptance and Functional Check Flight (FCF) Procedures (-6CF) Manual

FORMCHECKBOX

c. Acceptance and Functional Check Flight (-6CL) Checklist

FORMCHECKBOX

d. Workcards

FORMCHECKBOX

e. Inspection Requirements Cards

FORMCHECKBOX

f. Flow/Sequence Charts

FORMCHECKBOX

g. Checklists

(1) Maintenance/Operations (Non-Aircrew)

FORMCHECKBOX

(2) Operations (Aircrew)

FORMCHECKBOX

a. Manual

FORMCHECKBOX

b. Checklists

FORMCHECKBOX

a. Loading Data Manual

FORMCHECKBOX

b. Sample Basic Weight Checklists

FORMCHECKBOX

a. Flight Manual

FORMCHECKBOX

b. Performance Data Manual

FORMCHECKBOX

c. Air Refueling Manual

FORMCHECKBOX

d. Air Refueling Checklist

FORMCHECKBOX

a. Nuclear Weapons Basic Information and Loading Procedures

FORMCHECKBOX

b. Nuclear Weapons Loading Procedures

FORMCHECKBOX

c. Non-nuclear Munitions Basic

FORMCHECKBOX

d. Non-nuclear Loading Procedures

FORMCHECKBOX

e. Integrated Combat Turnaround Procedures

FORMCHECKBOX

f. Non-nuclear Munitions Loading Standard Data Packages (SDPs)

FORMCHECKBOX

g. Loading Procedures Checklists

FORMCHECKBOX

h. Integrated Loading Procedures Checklists

FORMCHECKBOX

i. Nuclear Weapons Loading Procedure Checklists

FORMCHECKBOX

j. Integrated Combat Turnaround Procedures Checklists

FORMCHECKBOX

k. NATO Stage B Cross-Servicing Checklists

FORMCHECKBOX

8. Space Operations and Support Documentation TOs -- Commercial specification (all space systems & missiles) -- MILSPEC (Intercontinental Ballistic Missiles) -- MILSPEC (Space Systems)

ANSI/AIAA-R024-1993

FORMCHECKBOX

MIL-PRF-38311

FORMCHECKBOX

MIL-PRF-38314

FORMCHECKBOX

a. Operations Manual

FORMCHECKBOX

b. Operations Checklists

FORMCHECKBOX

c. Technical Manuals and Related Checklists

FORMCHECKBOX

a. Non-nuclear Weapon Delivery Manual (Strategic Bomber & Tactical Aircraft)

FORMCHECKBOX

b. Nuclear Bomb Delivery Manual (Strategic Bomber Aircraft)

FORMCHECKBOX

c. Aircrew Nuclear Weapon Delivery Manual (Strategic Bomber Aircraft)

FORMCHECKBOX

d. Aircrew Nuclear Weapon Delivery Manual (Tactical Aircraft)

FORMCHECKBOX

e. Non-nuclear Weapon Delivery Checklist (Strategic Bomber & Tactical Aircraft)

FORMCHECKBOX

f. Nuclear Bomb Delivery Checklist (Strategic Bomber Aircraft)

FORMCHECKBOX

g. Aircrew Nuclear Weapon Delivery Checklist (Tactical Aircraft)

FORMCHECKBOX

h. Non-nuclear Weapon Delivery Source Data Packages

FORMCHECKBOX

a. General Equipment (GE) Manual

FORMCHECKBOX

b. General System (GS) Manuals

FORMCHECKBOX

c. Combined GE & GS Manual

FORMCHECKBOX

d. Job Guide (JG) Manuals

FORMCHECKBOX

e. Fault Reporting (FR) Manual

FORMCHECKBOX

f. Fault Isolation (FI) Manual

FORMCHECKBOX

g. Wiring Data (WD) Manual

FORMCHECKBOX

h. Schematic Diagram (SD) Manual

FORMCHECKBOX

a. Maintenance Manuals

(1) Intermediate Maintenance

FORMCHECKBOX

(2) Depot Maintenance

FORMCHECKBOX

(3) Combined (I&D) Maintenance

FORMCHECKBOX

(4) On Condition Maintenance

FORMCHECKBOX

b. Operation & Maintenance Instruction Manuals

FORMCHECKBOX

c. Special Manuals

(1) Aircraft Engine Testing and Trending Procedures

FORMCHECKBOX

(2) Aircraft Power Package Testing Procedures

FORMCHECKBOX

(3) Static Firing of Missile Motors

FORMCHECKBOX

(4) System Peculiar Corrosion Control

FORMCHECKBOX

(5) Nondestructive Inspection (NDI)

FORMCHECKBOX

(6) Aircraft Structural Integrity Program (ASIP)

FORMCHECKBOX

(7) ATE Operator Test Procedures

FORMCHECKBOX

(8) Special Requirements for Storage and Maintenance Procedures; AUR Munitions/Launchers and Associated Support Equipment, Conventional Components and CMBR Agents

FORMCHECKBOX

(9) Parachute Packing Procedures

FORMCHECKBOX

(10) Operators Instructions (Hand‑Held Flight Computers)

FORMCHECKBOX

(11) Installation‑Engineering Facility (Ground C-E Equipment)

FORMCHECKBOX

d. Checklists (IAW MIL-PRF-5096)

FORMCHECKBOX

e. With Illustrated Parts Breakdown (see notes)

FORMCHECKBOX

Table 2

Additional TM Type Selections

NOTES:

· Check all applicable boxes.

· For commercial manual supplemental data only, under the specification heading, enter “Same style and format,” “MIL-PRF-38807” (for IPB data), or “MIL-STD-38784.”

· For existing MIL-SPEC manuals not being updated to latest specification requirements, enter “Same style and format” under the specification heading.

· For manuals proposed to NGS, list the type of manual in the appropriate column and the NGS in the Specification column. Manuals proposed to an approved NGS shall meet the functional requirements of the approved TMSS for the TO type, e.g., OMMS prepared to S1000D shall meet the requirements of MIL-PRF-83495 (which serves as business rules for manual style, format, and content).

TO Number, Title, or Type of Manual

Specification Commercial Manual

Change/ Revision

Supplement Supplemental TM

Source Data

1. 31M1-2FMQ-19-1 Operations and Organizational Maintenance with Illustrated Parts Breakdown AN/FMQ-19 Automatic Meteorological Station (AMS)

MIL-STD-38807

MIL-PRF-32216

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

2.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

3.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

4.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

5.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

6.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

7.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

8.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

9.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

10.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

11.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

12.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

13.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

14.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

15.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

16.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

17.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

18.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

19.

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

FORMCHECKBOX

Part B - TM Delivery Requirements For AN/FMQ-19 AMS TM Data Type Delivered Operations and Organizational Maintenance with Illustrated Parts Breakdown

Delivery Format Requirements Codes

Digital delivery only:

X - Extensible Mark-up Language (XML)

EXAMPLE: M(G) / 2 [Paper and SGML / 2 copies]

NOTES:

· Delivery format requirements codes indicate the media/file format to be delivered for each program event.

· TCTO requirements are specified in the contract vehicle approving the TCTO.

· When on-line access is a contractual requirement, copy quantity will normally be ( (zero).

· For NGS or non-standard TMSS instances, delivery shall include the associated DTDs, FOSIs/Style Sheets, XML schemas, etc.

DELIVERY SCHEDULE

Enter Office Symbol and Address( Enter delivery requirements code/copy quantities required

OO-ALC/GHSBG (Attn: Carol Kaim) 6039 Wardleigh Rd (Bldg 1206) Hill AFB, UT 84056-5838

OO-ALC/GHSBG (Attn: Brenda Lund)

6039 Wardleigh Rd (Bldg 1206)

Hill AFB, UT 84056-5838

OO-ALC/GHSO (Attn: Tim Rotert) 6021 Gum Lane (Bldg 1228) Hill AFB, UT 84056-5838

OO-ALC/GHSEA (Attn: Al Sandstrom) 6049 Wardleigh Rd (Bldg 1205) Hill AFB, UT 84056-5838

HQ AFWA/A5/8 (Attn: Todd Allen) 101 Nelson Drive Offutt AFB, NE 68113

HQ AETC/A6OC (Attn: Gene Kline) 61 Main Circle, Suite 2

Randolph AFB, TX 78150

Section 3. Specification/Standard Interface Records (SIRs)

NOTES:

· All TMSS applicable to this contract shall have an appropriately tailored SIR attached to this section.

· SIRs included in the untailored TMCR format represent the minimum tailoring requirements that must be included in the final contract, unless the entire SIR is not applicable; e.g., if MIL-DTL-22202D is not required, the entire SIR can be deleted.

· MIL-STD-38784 must be included in all contracts/proposals for AF TMSS-developed TOs.

· Most specification “Acquisition Requirements” list the same two items for paragraphs 6.2a and 6.2b. For this contract enter:

· 6.2a. The title, number and date of each specification will be listed in the heading of the applicable SIR.

· 6.2b. The issue of the DODISS used in this contract is (enter date).

· Digital requirements shall not be tailored out. Tailoring shall be limited to the options expressed in paragraphs 6.2. Any requests for tailoring outside of these requirements must be coordinated with the specification Preparing Activity (PA) 754 ELSG/ILMT.

· Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the DoD Single Stock Point (DODSSP), Acquisition Streamlining and Standardization Information System (ASSIST) web page, http://www.dodssp.daps.dla.mil/assist.htm.

· Non-government Standards (NGS) shall be provided by the offeror. The Government will not be responsible for providing NGS.

· TMSS entries designated with A, F, M or N refer to Army, Air Force, Marine Corps or Navy requirements.

· Beneficial comments, recommendations, additions, data etc. which may be of use in improving any Air Force TMSS should be addressed to “Air Force Technical Manual Specifications and Standards Office, 754 ELSG/ILMT, Wright-Patterson AFB, OH 45433”. Do not include the street address, a building number, or a zip+4.

Specification/Standard Interface Record for MIL-DTL-22202D, 31 March 1999 Supplement 1, 31 March 1999

Manual, Technical, Aircraft Cross-Servicing Guide, Preparation of The requirements of 6.2 are met in this SIR (see below).

1.1 In addition to paper delivery, when this specification is used to develop digital delivery files (document type definitions – DTDs) contact the PA for additional instructions.

2.3 Ensure the listing for STANAG/ASCC Air Standard Documents is current. List applicable STANAG/ASCC Air Standards below.

(List STANAG/ASCC Air Standard Documents here.)

2.2.1 (Added) “Other government documents, drawings, and publications.

DEPARTMENT OF DEFENSE

DOD 5200.1-R

DoD Information Security Program Regulation

DOD 5220.22-M

National Industrial Security Program Operating Manual

4.

Replace with: “4. VERIFICATION.

“All cross-servicing guides shall meet the requirements of sections 3 and 5 of this specification, as required by the acquiring activity. The requirements set forth in this specification shall become a part of the contractor’s overall inspection system or quality program. The absence of any requirements in this specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the government for acceptance comply with all requirements of the contract. Use of sampling inspections shall be at the discretion of the contractor, and in accordance with commercially acceptable quality assurance procedures. However, use of sampling in QA procedures does not authorize submission of known defective material, either indicated or actual, nor does it commit the government to accept defective material.”

5. Replace with: “5. PACKAGING.

“5.1 Packaging Requirements. For acquisition purposes, the packaging requirements shall be as specified in the contract or order. When the actual packaging of material is to be performed by DoD personnel, these personnel need to contact the responsible packaging activity to determine packaging requirements. Packaging requirements are maintained by the Inventory Control Point’s packaging activity within the Military Department’s System Command. Packaging data retrieval is available from the Military Department’s or Defense Agency’s automated packaging files, CD-ROM products, or the responsible packaging activity.

“5.1.1 Encoded Computer Products. Packaging of encoded computer products for delivery shall be in accordance with the requirements of MIL-STD-1840.

“5.1.2 Classified Material. Classified material shall be packaged and identified in accordance with DOD 5200.1-R, DOD 5220.22-M, and the implementing Service regulations.”

6.2a Title, number, and date of the specification are listed above.

6.2b Issue of DODISS: (fill in issue of DODISS applicable to this contract)

6.2c Packaging requirements (see above).

6.2d Verification requirements (see above).

Specification/Standard Interface Record for MIL-STD-38784, 2 July 1995 Notice 1, 15 November 2000 Notice 2, 1 December 2000

Standard Practice for Manuals, Technical: General Style and Format Requirements

Global: Change references to “MIL-STD-1806” to read “DODD 5230.24.”

3.2.8 Continuous Tone Artwork. Delete paragraph.

3.2.9 Copy Freeze Date. Delete paragraph.

3.2.10 Cutline. Delete paragraph.

3.2.20 Layout Page. Delete paragraph.

4.2.1.2.1 Oversize Reproducible Copy. Delete paragraph.

4.2.7.1 Table Cutline (see 3.2.10). Delete paragraph.

4.2.8.1 Illustration Cutline (see 3.2.10). Delete paragraph.

4.2.8.3 Amend as follows: “4.2.8.3 Illustration legends (see 3.2.23). Legends shall be headed by the word “Legend” followed by the number of the figure to which it is applicable (see Figure 6). The entire legend shall be indented 5 spaces. If the legend is continued, the figure number and title shall be repeated, followed by a dash and the word “Continued.” Only that information which is necessary to clearly identify the items shall be included in the legend. Where methods such as the tabular presentation technique (as in an Illustrated Parts Breakdown/Repair Parts and Special Tools List) are used, no legends are required.”

NOTE: The <figtable> element, if included in the DTD, shall not be used in maintenance manuals.

* 4.5.1.10 Disclosure Notice. Change 1st sentence to read: “…except those with Distribution Statement A, IAW AFI 21-303 (F):”

* 4.5.1.11 Distribution Statement. Replace the last sentence with: “Include both the distribution statement letter (“A,” “B,” etc.) and wording from DODD 5230.24. Include the “Reason,” “Controlling DoD office,” and “Date of Determination” when required. If the reason is “Proprietary Data,” then each TM page containing proprietary data must be marked with the company name and the word “Proprietary” (e.g., “Boeing Proprietary”).”

4.5.1.13 Destruction Notice. Change the existing sentence to read: "...or X shall be marked with Handling and Destruction Notice "a" (below) on the cover/title..." Add a new second sentence as follows: "Unclassified TOs authorized for Public Release (Distribution Statement "A") shall be marked with disposition notice "b" (below) on the title or T-2 page."

4.5.1.13.a.

Designate existing paragraph as "a. HANDLING AND DESTRUCTION NOTICE..."

Add: "See TO 00-5-1 for specific destruction procedures."

4.5.1.13.b (Added)

b. “DISPOSITION NOTICE - Refer to TO 00-5-1 for disposition instructions.”

* 4.5.1.14 Copyright Credit Line. Add “If a copyright credit line is required, include a statement of government rights to publish, reproduce, and distribute the TM.”

4.5.3 List of Effective Pages. Change the first sentence to read: “A List of Effective Pages shall be prepared in accordance with Figure 13. Page borders shall be optional.”

4.6.2 Photographs/line drawings. Delete paragraph.

4.6.3.1 Retouching. Delete paragraph.

4.6.3.2 Prescreened photographs. Delete paragraph.

4.6.4 Continuous Tone Artwork (see 3.2.8). Delete paragraph.

4.6.5 Combination Artwork. Delete paragraph.

4.6.12 Color in Illustrations. Delete the first sentence: “Unless otherwise specified (see 6.2), color shall not be used.”

4.6.12.1 Separation of Colors. Delete paragraph.

4.6.12.2 Register Marks. Delete paragraph.

4.6.20 Crop and Size Marks. Delete.

4.6.21 Mounting of Artwork. Delete paragraph.

4.6.22 Identifying Artwork. Delete paragraph.

4.6.23 Covering of Artwork. Delete paragraph.

4.6.24 Review of Illustrations. Delete paragraph.

4.7.1 Advanced Change Pages. Delete paragraph.

4.7.2 Changes to Cover and Title Page. In the first sentence, delete the phrase “Except for silk screened or otherwise expensive covers”.

4.7.3.4 Transmittal Cover Sheets. In the last sentence, delete the phrase “i.e. reproducible copy, negatives, magnetic tape, disk, etc.”.

4.7.3.5 Changes to Illustrations. Delete paragraph.

4.9.2 Safety Supplements (see Figure 37). Change first sentence to read: Safety supplement “SS” borders and the words “SAFETY SUPPLEMENT” at the top and bottom of the supplement shall be in red. Other text, lettering, numbering, etc, shall be in black.”

Figure 5, Example Typical RDC Page.

Delete.

Figure 25 Cropping and Sizing of Illustrations.

Delete.

Figure 26, Identification, Marking, and Protective Covering of Artwork.

Delete.

Specification/Standard Interface Record for MIL-PRF-38804C, 1 March 1996 Amendment 1, 20 June 1997

Time Compliance Technical Orders – Preparation NOTE: Entries marked with an asterisk (*) will have to be manually entered and tagged in SGML files until the specification and its associated DTD and FOSI have been updated to incorporate the changes. The rescission date and statement will continue to appear in paragraph 3 of SGML-tagged TCTO files until the DTD and FOSI are updated.

Amendment 1 Delete entirely.

2.2.2 Change “AFM 67-1” to “AFMAN 23-110.”

3.5.2g Add new line: “g. Rescission Date (see 3.5.2.6.1)” Renumber following paragraphs to “h” through “l”.

3.5.2.4 Change 1st sentence to read: “…supplement thereto (see 3.6) provided by the acquiring activity on an AFMC Form 873 (see 6.5).”

3.5.2.5 Change 1st sentence to read: “…acquiring activity on an AFMC Form 873 (see 6.5).”

3.5.2.6 Change 1st sentence to read: “…acquiring activity on an AFMC Form 873 (see 6.5).” Change last sentence to read: : “The year, month, and day shall be in the YYYYMMDD format (see Figures 1 through 6).”

3.5.2.6.1 (Added) “Rescission Date. The contractor shall enter the TCTO rescission date in the upper right corner of the first page immediately below the TCTO issue date. The rescission date will be specified on the AFMC Form 873 (see 6.5). The date will be in the YYYYMMDD format.”

3.5.2.8 Add to the end of the paragraph: “See TO 00-5-15 for additional guidance.”

3.5.2.9.1d Change to read: “…reinstating and establishing a new rescission date for rescinded TO…”

3.5.2.9.4 Change “AFMC/AFCC” to “AFMC/AFCA/AFSPC”

3.5.3.3 Change “proofing” to “verification” (4 places)Change last sentence to read: “…waived, the office symbol, e-mail address and Defense Switched Network (DSN) phone number of the approving official shall…”

3.5.5.3 Replace “a” through “d” with the following:

a. (Added) Routine Safety Inspection Organizational/Intermediate Level TCTOs. “Not later than (#) days after receipt of this TCTO. Affected system/equipment shall be removed from service if this TCTO is not accomplished within the specified number of days, or 60 days prior to the TCTO rescission date, whichever comes first. The specified number of days for accomplishment shall be provided on the AFMC Form 873 (see 6.5).

b. Routine Action, Organizational/Intermediate Level, Safety TCTO. "Not later than ____ days after receipt of (this TCTO) (kits) (parts) (special tools). Failure to accomplish this TCTO by the preceding specified number of days, or 60 days prior to the TCTO rescission date, whichever comes first, shall automatically restrict operations or shall be justification for withdrawing affected system/equipment from service until compliance is accomplished. The specified number of days for accomplishment shall be provided on an AFMC Form 873 (see 6.5).

c. Routine Action, Organizational/Intermediate Level TCTO. Organizational/Intermediate level TCTOs having a compliance period in terms of days shall read: "Not later than ____ days after receipt of (this TCTO) (kits) (parts) (special tools). Failure to accomplish the work by expiration of the compliance period, or 60 days prior to the TCTO rescission date, whichever comes first, shall be justification for withdrawing the affected system/equipment from service until compliance is accomplished. The specified number of days and requirements for accomplishment shall be provided on an AFMC Form 873 (see 6.5).

d. Routine Action, Organizational/Intermediate Level, Based Upon Maintenance Practice. When the time period for accomplishment cannot be specified as a certain number of days after receipt of the TCTO, kits, parts or special tools, the TCTO may specify compliance at the time a known maintenance event occurs, such as "At the time of removal from Emergency War Order (EWO) status (or During scheduled modernization action). If not complied with by (date), or 60 days prior to the TCTO rescission date, whichever comes first, the system/equipment shall be removed from active service until compliance with the TCTO is accomplished. The preceding phrase is an example of the type to be used and may be expanded or worded to the individual requirement as needed. Use of the phrases "upon failure," "upon accumulation" or "when reaching" are not authorized for any TCTO. The required statement shall be provided on an AFMC Form 873 (see 6.5).

e. Routine Action, Depot Level. These modifications require specified accomplishment at a time designated by the acquiring activity by means of the AFMC Form 873 (see 6.5) at overhaul, contractor team, force modernization, AFMC schedule or whatever other phrase that is most appropriate.

3.5.5.4 Add new sentence as follows: “The required statements shall be provided on an AFMC Form 873 (see 6.5).”

3.5.5.5 (Added in Amendment 1) Delete.

3.5.7.1.1.1 Change 4th and 5th lines to read: “…concept waived by (insert name/rank/office symbol/DSN phone number and e-mail address of the Lead Command POC authorizing a waiver of the complete…”

3.5.7.2 Change “proofing” to “verification” (2 places)

3.5.7.2.1 (Added) “For Inspection TCTOs, the AFSCs and manhours shall be based on Maintenance Data Collection (MDC) records. The equivalent work phases will be:

a.

Equipment preparation.

b.

Access work area.

c.

Perform inspection.

d.

Close work area.

e.

Operational check and documentation.”

3.5.7.2.1 (Existing) Renumber as 3.5.7.2.2.

3.5.10.1.4 Change last line to read “...with the criteria established in AFI 21-103, Chapter 9 (-21 TOs).

3.5.11.1 Change 1st sentence to read: “…the name, organization and office symbol, DSN telephone number, and e-mail address of the POC responsible…”

Change 2nd sentence to read: “…and the information for the POC authorizing…”

3.6 Delete the last sentence (“All supplements shall be assigned a new data code number.”)

3.6.1 Change 1st sentence to read: “…supplement, or it explicitly changes the TCTO rescission date.”

3.6.6 Delete “, IF APPROVED BY THE MAJCOM,” in the NOTE text.

4.1 Change title to “Contractor Prototyping.”

4.1b Change to read: “…perform the prototyping functions specified…”

4.1d Change to read: “…review any of the prototyping functions, when…”

4.1.1 Change “verification” to “prototyping” (2 places)

4.1.1d, e & f (Added) “d. Form, fit and function of TCTO kits and modified components.

e. TO update accuracy.

f. Proper function of the modified equipment.”

5.2 Replace with: “Bill of Materials. TCTO kits shall contain a Bill of Materials listing all of the items required to accomplish the TCTO. As a minimum, the format of the Bill of Material shall be as follows:”

6.2l Change to read: “Issue and Rescission dates (see 3.5.2.6 & 3.5.2.6.1).”

6.2x Delete.

6.4.8 Change “verification” to “prototyping” (2 places)

6.4.8a Add “Includes validating the form, fit, and function of any kits involved, accuracy of associated TO updates, and proper operation of the modified equipment.”

6.5 Change 1st sentence to read: “…are contained in TO 00-5-15, Air Force Time Compliance Technical Order Process.”

6.6 Add “prototyping” and “supplement” to key word list.

Figures 3, 4 & 5 Change “Proofing” to “Verification” in each figure.

Specification/Standard Interface Record for ASD-S1000D Business Rules (date)

International Specification for Technical Publications Utilizing a Common Source Database

TBD