Attachment 12 - Asbestos Inspection Bldg 979 - 12 Feb 2023.pdf

Arizona Environmental Specialists

Report of Findings Limited NESHAP Asbestos Inspection

Luke AFB Building 979, 998, & 1040 14185 Falcon Street

Luke Air Force Base, Arizona 85309

Submitted to:

Mr. Carl Moser

56 CES

13970 Gillespie Drive

Submitted by:

Arizona Environmental Specialists, LLC

201 East Southern Suite 114 Tempe, Arizona 85282

February 12th, 2023

AES Project No. 2302468-23468

201 East Southern Suite 114 Tempe, Arizona 85282~Phone:480.553.7052~Fax:480.553.7056~www.azenvsp.com

Re: Report of Findings- Limited NESHAP Asbestos Inspection

Luke AFB Building 979, 998, & 1040 14185 Falcon Street

Arizona Environmental Specialists (AES) is providing this letter to document the laboratory results of the asbestos bulk samples collected from the above mentioned address. AES collected bulk samples from suspect asbestos-containing building materials that will be impacted in upcoming demolition/renovation activities. Bulk sample collection was performed by Arizona Environmental Specialists’ accredited EPA/AHERA Building Inspector Mr. James Soto on Monday, February 6th, 2023. Sampling was performed in general accordance with the AHERA sampling protocol EPA 40 CFR Part 763.86 Sampling.

Samples were delivered to Lindus Environmental Laboratory in Phoenix, Arizona for visual inspection and microscopic analysis. Samples were analyzed using Polarized Light Microscopy (PLM) coupled with dispersion staining as outlined in the EPA Method 600/R-93/116. Lindus Environmental Laboratory is accredited under the National Voluntary Laboratory Accreditation Program (NVLAP). Lindus Environmental Laboratory's NVLAP Lab Code is 600113-0.

During the site investigation for asbestos-containing materials, AES sampled five (5) suspect materials that will be impacted in upcoming demolition/renovation activities. Of the five materials identified, one was found to contain asbestos in amounts greater than one percent by PLM Analysis. The following is a list of the suspect materials sampled:

Building 979 Suspect Asbestos Materials Results-Positive/Negative

• 01 Vinyl composite tile and mastic, two layers Positive

• 02 Block and mortar Negative

Building 998

Suspect Asbestos Materials Results-Positive/Negative

• 01 Concrete Negative

Building 1040 Suspect Asbestos Materials Results-Positive/Negative

• 01 Gypsum wall board, medium texture Negative

• 02 Block and mortar Negative

February 12th, 2023 AES Project No. 2302468-23468

Mr. Carl Moser

56 CES

13970 Gillespie Drive

Dear Mr. Moser:

Report of Findings- Limited NESAHP Asbestos Inspection

Luke AFB Building 979, 998, & 1040 14185 Falcon Street

Summary of Findings-Building 979

HA

No.

Material Description

Condition Quantity NESHAP Classification

% Asbestos and Type

Material Locations

01 Vinyl composite tile and mastic, two layers

Good 250 S.F. Category II Non-Friable

Green vinyl tile 2% Chrystoile Black mastic 4% Chrystoile

B979/Rapcon

Inspector Information

Name of

EPA/AHERA

Building Inspector

Inspection date

Number of Samples

Building Inspector Certification Number

Training Provider

Expiration Date

James Soto 02/06/23 15 4644-7125-051622 The Asbestos Institute

May 16th, 2023

NESHAP Regulations

The scope and applicability of the National Emission Standard for Hazardous Air Pollutants (NESHAP) asbestos regulation (Title 40 CFR, Part 61 Subpart M), applies in all buildings except single residential buildings having four units or less. The NESHAP requires a thorough inspection before any renovation or demolition activity. Whenever regulated asbestos-containing material (RACM) is about to be distributed by demolition or renovation the NESHAP requires EPA notification, requires the management of waste through and after disposal, and no visible emissions.

Category I material is defined as asbestos-containing resilient floor covering, asphalt roofing products, packings, and gaskets. Asbestos-containing mastic is also considered a Category I material (EPA determination – April 9, 1991). Category II material is defined as all remaining types of non-friable ACM not included in Category I that, when dry, cannot be crumbled, pulverized, or reduced to powder by hand pressure.

Report of Findings- Limited NESAHP Asbestos Inspection

Luke AFB Building 979, 998, & 1040 14185 Falcon Street

Luke Air Force Base, Arizona 85309

OSHA Regulations

The scope and applicability of the Occupational Safety and Health Administration (OSHA) asbestos regulation (29 CFR 1926.1101 Asbestos) applies whenever a worker may be exposed to asbestos. This regulation requires that employers protect employees. The regulation states that the building owner is the basic employer. The OSHA asbestos regulation serves as a specification for contractors, and a notification regulation for building owners. The OSHA regulation 29 CFR 1926.1101 (k) Communication of Hazards requires that the building owner determine the presence, location and quantity of ACM before construction activities begin. The building owner must notify persons of the presence, location and quantity of ACM before it is disturbed. Prior to disturbance, the building owner must notify contractors, in-house maintenance personnel, adjacent contractors on multi-employer worksites and tenants.

Based on the OSHA asbestos standard 29 CFR 1926.1101. Class I Asbestos Work means activities involving the removal of asbestos containing Thermal System Insulation (TSI) and Surfacing Material.

This includes, but is not necessarily limited to pipe fitting insulation, pipe run insulation, and fireproofing.

Based on the same OSHA asbestos standard, Class II Asbestos Work means activities involving the removal of ACM which is not TSI or surfacing materials. This includes, but is not necessarily limited to;

wallboard, floor tile and sheeting, roofing and siding shingles, construction mastics, duct seam tape, fire doors and drywall compound.

Report Qualifications

AES has attempted to evaluate the existing conditions explained in this summary using superior procedures as opposed to those performing similar services. Even though the inspections are thorough, some areas containing asbestos may be unattainable or are diverse from those at alternative sample locations.

Considering, conditions at every location are not equivalent. The results presented in this report are relevant to the dates of our site inspections and the scope of included services and should not be relied on to account for conditions at substantially later dates.

Enclosed, is a copy of the PLM laboratory analysis report and a copy of Arizona Environmental Specialist’s personnel certifications.

Sincerely, Brian Chrisman Project Manager

Report Provided For:

Tempe, AZ 85282

Sampled: 02/06/2023 Received: 02/06/2023 Analyzed: 02/06/2023 Reported: 02/06/2023

PO Number:

Sample Condition: Acceptable

Analysis Requested: Asbestos in Bulk Building Materials

Method: EPA-600/R-93/116: Determination of Asbestos in Bulk Building Materials

EPA-600/M4-82-020: Determination of Asbestos in Bulk Insulation Samples

Report Version: 1 A number greater than 1 indicates a revised report has been issued.

Internal Procedure: Document #021

NVLAP Lab Code: 600113-0

Internal Report: Document #043 V6.5 06/2022

Arizona Environmental Specialists

J020634

Approved Signatory:

Adam Lindus

Inhomogeneous samples are subsampled into homogeneous component layers and analyzed individually. Any deviations, additions to, or exclusions from the test method are documented in the Report Comments section of the sample data. The results contained in this report relate only to the samples tested/received. This report shall not be reproduced except in full, without written approval of the laboratory. This report must not be used by the client to claim product certification, approval, or endorsement by

NVLAP, NIST, or any agency of the Federal Government. Lindus LLC reserves the right to dispose of samples after 30 days.

Project Name:

Luke Air Force Base B.979

Lab ID:

Lindus LLC

1645 E Missouri Ave Suite 230

Phoenix, AZ 85016

480-845-9081 Page 1 of 4J020634

Sampled: 02/06/2023 Project Name: Luke Air Force Base B.979

Received: 02/06/2023 Lab Number: J020634

Analyzed: 02/06/2023

Reported: 02/06/2023 Total Samples Submitted: 3

≥ Samples Containing Asbestos (≥1%): 3

Samples Containing Trace Asbestos (<1%): 0

Sample Number Sample Description Asbestos Point Count

J020634-001 01A 12'' VCT / Mastic (Two Layers) 4% Chrysotile

J020634-002 01B 12'' VCT / Mastic (Two Layers) 4% Chrysotile

J020634-003 01C 12'' VCT / Mastic (Two Layers) 4% Chrysotile

Asbestos present in concentration ≥ 1%

Asbestos present in trace amounts

ND - No asbestos Detected

Summary of Results

Page 2 of 4J020634

J020634-001 01A 12'' VCT / Mastic (Two Layers)

Other Fibrous

Material (%) Matrix Asbestos Point Count

Brown Vinyl Tile 0 ND -

Tan Mastic 0 ND -

Green Vinyl Tile 0 2% Chrysotile -

Black Mastic 0 T 4% Chrysotile -

J020634-002 01B 12'' VCT / Mastic (Two Layers)

Other Fibrous

Material (%) Matrix Asbestos Point Count

Brown Vinyl Tile 0 ND -

Tan Mastic 0 ND -

Green Vinyl Tile 0 2% Chrysotile -

Black Mastic 0 T 4% Chrysotile -

J020634-003 01C 12'' VCT / Mastic (Two Layers)

Other Fibrous

Material (%) Matrix Asbestos Point Count

Brown Vinyl Tile 0 ND -

Tan Mastic 0 ND -

Green Vinyl Tile 0 2% Chrysotile -

Black Mastic 0 T 4% Chrysotile -

Page 3 of 4J020634

① ③ ④ ⑥

A121201-001 GWB-Med Knockdown Tex-(Wall)

Other Fibrous

Material (%) Matrix Asbestos Point Count

White Drywall with Brown Paper 15 CE ND -

White Joint Compound 0 3% Chrysotile -

Cream Tape 80 CE ND -

White Texture with Multicolored Paint 0 Trace Chrysotile 0.25%

Report Comments: Sample received wet

⑧

① Unique lab and sample number assigned by the laboratory. In this example the lab number is A121201 and the sample number is 001.

② Sample number/location/description assigned by the customer on the Chain of Custody form.

③ The estimated percentage of the layer constituting other fibrous materials, i.e., non-asbestos fibers.

④ Identity of matrix materials, if known.

B=Binder C=Carbonates CE=Cellulose F=Fiberglass

G=Gypsum M=Mica P=Perlite S=Synthetic Fibers

T=Tar Q=Quartz V=Vermiculite MW=Mineral Wool

⑤ Asbestos type and concentration.

ND = None Detected. The Laboratory reports “None Detected” when the laboratory homogenizes the sample in some way or analyzes a sufficient number of sub-samples to obtain a representative analysis whereby no asbestos fibers have been detected in any sub-sample preparations.

Trace = Asbestos is present in the sample but at concentrations so low it is far from the level of 1%. The Laboratory is confident it is NOT necessary to analyze the sample by a more accurate and precise method.

⑥ Point count result if requested.

⑦ Description of layers comprising the sample, each analyzed individually.

⑧ Report comments (if applicable) describe any problems encountered during the analysis as well as any deviations, additions to, or exclusions from the test method.

FFbruarF 2F23

Notes / Sample Interpretation

② ⑤

⑦

Page 4 of 4J020634

Sampled: 02/06/2023 Received: 02/06/2023 Analyzed: 02/07/2023 Reported: 02/07/2023

Sample Condition: Acceptable

Analysis Requested: Asbestos in Bulk Building Materials

Method: EPA-600/R-93/116: Determination of Asbestos in Bulk Building Materials

EPA-600/M4-82-020: Determination of Asbestos in Bulk Insulation Samples

Report Version: 1 A number greater than 1 indicates a revised report has been issued.

Internal Procedure: Document #021

NVLAP Lab Code: 600113-0

Internal Report: Document #043 V6.5 06/2022

Arizona Environmental Specialists

J020635

Approved Signatory:

Adam Lindus

Inhomogeneous samples are subsampled into homogeneous component layers and analyzed individually. Any deviations, additions to, or exclusions from the test method are documented in the Report Comments section of the sample data. The results contained in this report relate only to the samples tested/received. This report shall not be reproduced except in full, without written approval of the laboratory. This report must not be used by the client to claim product certification, approval, or endorsement by

NVLAP, NIST, or any agency of the Federal Government. Lindus LLC reserves the right to dispose of samples after 30 days.

Project Name:

Luke Air Force Base B1040

Lab ID:

Lindus LLC

1645 E Missouri Ave Suite 230

480-845-9081 Page 1 of 4J020635

Sampled: 02/06/2023 Project Name: Luke Air Force Base B1040

Received: 02/06/2023 Lab Number: J020635

Analyzed: 02/07/2023

Reported: 02/07/2023 Total Samples Submitted: 6

≥ Samples Containing Asbestos (≥1%): 0

0 Samples Containing Trace Asbestos (<1%): 0

Sample Number Sample Description Asbestos Point Count

J020635-001 01A GWB Med Texture ND

J020635-002 01B GWB Med Texture ND

J020635-003 01C GWB Med Texture ND

J020635-004 02A Block & Mortar ND

J020635-005 02B Block & Mortar ND

J020635-006 02C Block & Mortar ND

Asbestos present in concentration ≥ 1%

Asbestos present in trace amounts

ND - No asbestos Detected

Page 2 of 4J020635

J020635-001 01A GWB Med Texture

Material (%) Matrix Asbestos Point Count

Brown / White Wallboard W/ White Paint 10 CE ND -

J020635-002 01B GWB Med Texture

Other Fibrous

Material (%) Matrix Asbestos Point Count

Brown / White Wallboard W/ White Paint 10 CE ND -

J020635-003 01C GWB Med Texture

Other Fibrous

Material (%) Matrix Asbestos Point Count

Brown / White Wallboard W/ White Paint 10 CE ND -

J020635-004 02A Block & Mortar

Other Fibrous

Material (%) Matrix Asbestos Point Count

Tan Block W/ Tan Paint 0 ND -

J020635-005 02B Block & Mortar

Other Fibrous

Material (%) Matrix Asbestos Point Count

Tan Block W/ Tan Paint 0 ND -

J020635-006 02C Block & Mortar

Other Fibrous

Material (%) Matrix Asbestos Point Count

Tan Block W/ Tan Paint 0 ND -

Page 3 of 4J020635

Other Fibrous

Material (%) Matrix Asbestos Point Count

White Drywall with Brown Paper 15 CE ND -

White Joint Compound 0 3% Chrysotile -

Cream Tape 80 CE ND -

White Texture with Multicolored Paint 0 Trace Chrysotile 0.25%

Report Comments: Sample received wet

⑧

① Unique lab and sample number assigned by the laboratory. In this example the lab number is A121201 and the sample number is 001.

② Sample number/location/description assigned by the customer on the Chain of Custody form.

③ The estimated percentage of the layer constituting other fibrous materials, i.e., non-asbestos fibers.

④ Identity of matrix materials, if known.

B=Binder C=Carbonates CE=Cellulose F=Fiberglass

G=Gypsum M=Mica P=Perlite S=Synthetic Fibers

T=Tar Q=Quartz V=Vermiculite MW=Mineral Wool

⑤ Asbestos type and concentration.

ND = None Detected. The Laboratory reports “None Detected” when the laboratory homogenizes the sample in some way or analyzes a sufficient number of sub-samples to obtain a representative analysis whereby no asbestos fibers have been detected in any sub-sample preparations.

Trace = Asbestos is present in the sample but at concentrations so low it is far from the level of 1%. The Laboratory is confident it is NOT necessary to analyze the sample by a more accurate and precise method.

⑥ Point count result if requested.

⑦ Description of layers comprising the sample, each analyzed individually.

⑧ Report comments (if applicable) describe any problems encountered during the analysis as well as any deviations, additions to, or exclusions from the test method.

00bruar0 2023

Notes / Sample Interpretation

② ⑤

Page 4 of 4J020635

Sample Condition: Acceptable

Analysis Requested: Asbestos in Bulk Building Materials

Method: EPA-600/R-93/116: Determination of Asbestos in Bulk Building Materials

EPA-600/M4-82-020: Determination of Asbestos in Bulk Insulation Samples

Report Version: 1 A number greater than 1 indicates a revised report has been issued.

Internal Procedure: Document #021

NVLAP Lab Code: 600113-0

Internal Report: Document #043 V6.5 06/2022

Arizona Environmental Specialists

J020636

Approved Signatory:

Adam Lindus

Inhomogeneous samples are subsampled into homogeneous component layers and analyzed individually. Any deviations, additions to, or exclusions from the test method are documented in the Report Comments section of the sample data. The results contained in this report relate only to the samples tested/received. This report shall not be reproduced except in full, without written approval of the laboratory. This report must not be used by the client to claim product certification, approval, or endorsement by

NVLAP, NIST, or any agency of the Federal Government. Lindus LLC reserves the right to dispose of samples after 30 days.

Project Name:

Luke Air Force Base B.979

Lab ID:

Lindus LLC

1645 E Missouri Ave Suite 230

480-845-9081 Page 1 of 4J020636

Sampled: 02/06/2023 Project Name: Luke Air Force Base B.979

Received: 02/06/2023 Lab Number: J020636

Analyzed: 02/07/2023

Reported: 02/07/2023 Total Samples Submitted: 3

≥ Samples Containing Asbestos (≥1%): 0

0 Samples Containing Trace Asbestos (<1%): 0

Sample Number Sample Description Asbestos Point Count

J020636-001 02A Block & Mortar ND

J020636-002 02B Block & Mortar ND

J020636-003 02C Block & Mortar ND

Asbestos present in concentration ≥ 1%

Asbestos present in trace amounts

ND - No asbestos Detected

Page 2 of 4J020636

J020636-001 02A Block & Mortar

Material (%) Matrix Asbestos Point Count

Grey Stucco W/ White Paint 0 ND -

J020636-002 02B Block & Mortar

Other Fibrous

Material (%) Matrix Asbestos Point Count

Grey Stucco W/ White Paint 0 ND -

J020636-003 02C Block & Mortar

Other Fibrous

Material (%) Matrix Asbestos Point Count

Grey Stucco W/ White Paint 0 ND -

Page 3 of 4J020636

Other Fibrous

Material (%) Matrix Asbestos Point Count

White Drywall with Brown Paper 15 CE ND -

White Joint Compound 0 3% Chrysotile -

Cream Tape 80 CE ND -

White Texture with Multicolored Paint 0 Trace Chrysotile 0.25%

Report Comments: Sample received wet

⑧

① Unique lab and sample number assigned by the laboratory. In this example the lab number is A121201 and the sample number is 001.

② Sample number/location/description assigned by the customer on the Chain of Custody form.

③ The estimated percentage of the layer constituting other fibrous materials, i.e., non-asbestos fibers.

④ Identity of matrix materials, if known.

B=Binder C=Carbonates CE=Cellulose F=Fiberglass

G=Gypsum M=Mica P=Perlite S=Synthetic Fibers

T=Tar Q=Quartz V=Vermiculite MW=Mineral Wool

⑤ Asbestos type and concentration.

ND = None Detected. The Laboratory reports “None Detected” when the laboratory homogenizes the sample in some way or analyzes a sufficient number of sub-samples to obtain a representative analysis whereby no asbestos fibers have been detected in any sub-sample preparations.

Trace = Asbestos is present in the sample but at concentrations so low it is far from the level of 1%. The Laboratory is confident it is NOT necessary to analyze the sample by a more accurate and precise method.

⑥ Point count result if requested.

⑦ Description of layers comprising the sample, each analyzed individually.

⑧ Report comments (if applicable) describe any problems encountered during the analysis as well as any deviations, additions to, or exclusions from the test method.

00bruar0 2023

Notes / Sample Interpretation

② ⑤

Page 4 of 4J020636

Sample Condition: Acceptable

Analysis Requested: Asbestos in Bulk Building Materials

Method: EPA-600/R-93/116: Determination of Asbestos in Bulk Building Materials

EPA-600/M4-82-020: Determination of Asbestos in Bulk Insulation Samples

Report Version: 1 A number greater than 1 indicates a revised report has been issued.

Internal Procedure: Document #021

NVLAP Lab Code: 600113-0

Internal Report: Document #043 V6.5 06/2022

Arizona Environmental Specialists

J020637

Approved Signatory:

Adam Lindus

Inhomogeneous samples are subsampled into homogeneous component layers and analyzed individually. Any deviations, additions to, or exclusions from the test method are documented in the Report Comments section of the sample data. The results contained in this report relate only to the samples tested/received. This report shall not be reproduced except in full, without written approval of the laboratory. This report must not be used by the client to claim product certification, approval, or endorsement by

NVLAP, NIST, or any agency of the Federal Government. Lindus LLC reserves the right to dispose of samples after 30 days.

Project Name:

Luke Air Force Base #998

Lab ID:

Lindus LLC

1645 E Missouri Ave Suite 230

480-845-9081 Page 1 of 4J020637

Sampled: 02/06/2023 Project Name: Luke Air Force Base #998

Received: 02/06/2023 Lab Number: J020637

Analyzed: 02/07/2023

Reported: 02/07/2023 Total Samples Submitted: 3

≥ Samples Containing Asbestos (≥1%): 0

0 Samples Containing Trace Asbestos (<1%): 0

Sample Number Sample Description Asbestos Point Count

J020637-001 01A Concrete ND

J020637-002 01B Concrete ND

J020637-003 01C Concrete ND

Asbestos present in concentration ≥ 1%

Asbestos present in trace amounts

ND - No asbestos Detected

Page 2 of 4J020637

J020637-001 01A Concrete

Material (%) Matrix Asbestos Point Count

Grey Epoxy 0 ND -

Grey Concrete 0 ND -

J020637-002 01B Concrete

Other Fibrous

Material (%) Matrix Asbestos Point Count

Grey Epoxy 0 ND -

Grey Concrete 0 ND -

J020637-003 01C Concrete

Other Fibrous

Material (%) Matrix Asbestos Point Count

Grey Epoxy 0 ND -

Grey Concrete 0 ND -

Page 3 of 4J020637

Other Fibrous

Material (%) Matrix Asbestos Point Count

White Drywall with Brown Paper 15 CE ND -

White Joint Compound 0 3% Chrysotile -

Cream Tape 80 CE ND -

White Texture with Multicolored Paint 0 Trace Chrysotile 0.25%

Report Comments: Sample received wet

⑧

① Unique lab and sample number assigned by the laboratory. In this example the lab number is A121201 and the sample number is 001.

② Sample number/location/description assigned by the customer on the Chain of Custody form.

③ The estimated percentage of the layer constituting other fibrous materials, i.e., non-asbestos fibers.

④ Identity of matrix materials, if known.

B=Binder C=Carbonates CE=Cellulose F=Fiberglass

G=Gypsum M=Mica P=Perlite S=Synthetic Fibers

T=Tar Q=Quartz V=Vermiculite MW=Mineral Wool

⑤ Asbestos type and concentration.

ND = None Detected. The Laboratory reports “None Detected” when the laboratory homogenizes the sample in some way or analyzes a sufficient number of sub-samples to obtain a representative analysis whereby no asbestos fibers have been detected in any sub-sample preparations.

Trace = Asbestos is present in the sample but at concentrations so low it is far from the level of 1%. The Laboratory is confident it is NOT necessary to analyze the sample by a more accurate and precise method.

⑥ Point count result if requested.

⑦ Description of layers comprising the sample, each analyzed individually.

⑧ Report comments (if applicable) describe any problems encountered during the analysis as well as any deviations, additions to, or exclusions from the test method.

00bruar0 2023

Notes / Sample Interpretation

② ⑤

Page 4 of 4J020637

James Soto

May 16, 2022

ON-4644-7125-051622

16-May-2022

16-May-2023

Powered by TCPDF (www.tcpdf.org) http://www.tcpdf.org