Attachment 7 Test Reports and AHP ASME.pdf

64 Log Canoe Circle Stevensville, MD 21666

Tel (410) 604-3142 Fax (410) 604-3209

Air Receivers

A

B

C

D

A

B

C

D

TOLERANCES ON

SHEET: 1 OF 1SCALE

PROPRIETARY AND CONFIDNETIAL

THE INFORMATION CONTAINED IN THIS DRAWING IS

THE SOLE PROPERTY OF AMERICAN AIRWORKS. ANY

REPRODUCTION IN PART OR AS A WHOLE WITHOUT

THE WRITTEN PERMISSION OF AMERICAN AIRWORKS

IS PROHIBITED.

UNLESS OTHERWISE

SPECIFIED DIMENSIONS

ARE IN INCHES

DATE: 01/31/14

DWG BY: T.M.

FINISH: SEE BOM

SEE BOMMATERIAL:

± .005

3PLC2PLC

.01

SIZE

C

PART NUMBER: REV

A

DESCRIPTION:

AMERICAN

AIRWORKS

PO BOX 1000

578 ROBERT C BYRD DR.

SOPHIA, WV 25921

304-683-4595 PH

REV BY APPROVEDDATE

1 : 1

ASME Configuration psi psi

No Qty Part No Description

1 6 AC40005 ASME Cylinder 430-490 cu. ft

2 6 AC50065 Bushing, 1-11.5” NGT x 1/4” FNPT

3 6 AC50125U Relief Valve, 6500 psi

4 6 AC20014 Elbow, 1/4” MNPT x 1/4” FNPT

5 6 AC50019 Drain Valve, 6000 psi

6 6 AC20010 Union, Hex, 1/4” MNPT

7 6 AC30009-1 Gauge, 7500, 2.5”

8 6 AC20022 Tee, 1/4” MNPT Run

9 6 AC50080 On/Off Valve

10 1 AC20016 Elbow, 1/4” FNPT x 1/4” JIC-M

11 5 AC20023-1 Tee, Street 1/4” JIC-M

12 5 AC80052 Pigtail, 3/16” x 24”

13 1 AC70051HHD6 Rack, Horizontal

1340 Lexington Avenue • Rochester, New York 14606 • Phone: (585) 277-1000 • Fax: (585) 277-1092Avenue

SUBMITTAL

SECTION 43 12 19

HIGH PRESSURE COMPRESSED AIR (AHP) EQUIPMENT AND PIPING

SD-03 – 2.4 – ASME Test Reports for AHP Receivers

· Attached are the Manufacturer’s Data Report for Pressure Vessels in accordance with

ASME Boiler and Pressure Vessel Code Rules, Section VIII, Div. 1 for the AHP

Receiving Bottles. They are organized into three sets by serial numbers located in the top right corner of the page.

(Name and address of Manufacturer)

(Name and address of Purchaser)

901B-B-9432-23

(Name of part, item number, Manufacturer's name and identifying stamp)

5.

(Year built)

-50 °F 5250 / 7000

FORM U-1A MANUFACTURER'S DATA REPORT FOR PRESSURE VESSELS

(Alternative Form for Single Chamber, Completely Shop or Field Fabricated Vessels Only)

As Required by the Provisions of the ASME Boiler and Pressure Vessel Code Rules, Section VIII, Division 1

1. Manufactured and certified by

2. Manufactured for

3. Location of Installation

4. Type (Manufacturer's serial number) (National Board number) (Horizontal or vertical, tank) (Drawing number)

(CRN)

11. Supports: Skirt (Yes or no)

No Lugs

(Number)

Legs

Other (Describe)

N/A Attached (Where and how)

9. MAWP

Min. design metal temp. at Hydro, pneu., or comb. test pressure

10. Nozzles, inspection and safety valve openings:

ASME Code, Section VIII, Division 1

(Nominal thickness) (Corr. allow.) (Material spec. number, grade)

6. Shell:

7. Seams:

8. Heads: (a) Material

(Spec. no., grade) (Spec. no., grade)

[Long. (welded, dbl., sngl., lap, butt)] [R.T.(spot or full)] (Eff.,%) (H.T. temp) (Time, hr) [Girth. (welded, dbl., sngl., lap, butt)] [R.T. (spot or full)]

[Edition and Addenda, if applicable (date)] (Code Case numbers) (Special service per UG-120(d))

(Inner diameter) [Length (overall)]

12. Remarks: Manufacturer's Partial Data Reports properly identified and signed by Commissioned Inspectors, have been furnished for the following items of the report:

(Name and address)

Charpy Impact Per UG84.

For Non-Corrosive Service.

Constructed in conformance with Appendix 22, Integrally Forged Vessels.

Hydro Tested in Vertical position.

Additional Remarks - See Attached U-4...

137931-1

Work Order #

(No. of courses)

Corrected

Copy

American Airworks

Customer

Norris Cylinder Company, 4818 W. Loop 281, Longview, Texas, 75603

HYDRO. at 9375 psi

Unknown

SA372 Grade F, Class 70 SA372 Grade F, Class 70

Seamless None 100% 1100 °F 1 Seamless None

N/A UCS 65 Low Temp, Service

American Airworks, 578 ROBERT C BYRD DRIVE, Box 1000, Sophia, West Virginia, 25921-1000

46678-46689 GS146678 to GS146689

Horiz./Vert.

0.784" 0 in SA372 Grade F, Class 70 0' 8" (ID) 4' 6"

2010/ 2011a

(Eff., %) 100%

(b) Material

5250 / 7000 N/A at max. temp. 200 °F N/A

(Internal) (Internal) (External) (External)

N/A Proof test

No. Type ID Flange

Thk

Min Hub Thk

How

Material

Bolting

Num & Size

Material

Washer (OD, ID, thk)

Washer

OD

Body Flanges on Shells

Location

N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A

Location (Top, Bottom, Ends)

Minimum Thickness

Corrosion Allowance

Crown Radius Knuckle Radius Elliptical Ratio Conical Apex Angle

Hemispherical Radius

Flat

Diameter

Side to Pressure (Convex or

Concave)

(a) END 0.784" 0 N/A N/A N/A N/A 4.835" N/A Concave

(b) END 0.784" 0 N/A N/A N/A N/A 4.835" N/A Concave

Location Type ID Flange Thk Min Hub

How Attached Material

Num & Size Bolting Material

Washer (OD, ID, thk)

Washer Material

Body Flanges on Heads

N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A (a)

Purpose (Inlet, Outlet, Drain, etc.)

No.

Diameter or Size

Type

Material

Nozzle Flange

Nozzle Thickness

Nom. Corr.

Reinforcement

Material Attachment Details

Nozzle Flange Location (Insp.

Open.)

Inlet 1 .25" Machined SA372 Grade F, Class 70 None HD

Outlet 1 1" Machined SA372 Grade F, Class 70 None HD

Drain 1 .25" Machined SA372 Grad F, Class 70 None HD

S/N: GS146679

Andrea 01/10/18 10:12:41: S/N: GS146679

Form and version: U1A-18

[National Board (incl. endorsements)] (Authorized Inspector)

HSB Global Standards, of Hartford, CT

I, the undersigned, holding a valid commission issued by The National Board of Boiler and Pressure Vessel Inspectors and employed by and state that, to the best of my knowledge and belief, the Manufacturer has constructed this pressure vessel in accordance with ASME BOILER

AND PRESSURE VESSEL CODE, Section VIII, Division 1. By signing this certificate neither the Inspector nor his/her employer makes any warranty, expressed or implied, concerning the pressure vessel described in this Manufacturer's Data Report. Furthermore, neither the Inspector nor his/her employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with this inspection.

We certify that the statements made in this report are correct and that all details of design, material, construction, and workmanship of this vessel conform to the ASME BOILER AND PRESSURE VESSEL CODE, Section VIII, Division 1. "U" Certificate of Authorization Number

CERTIFICATE OF SHOP/FIELD COMPLIANCE

Signed

(Representative)

Co. name expires

Date 07/21/2015 (Manufacturer)

CERTIFICATE OF SHOP/FIELD INSPECTION

Norris Cylinder Company 4818 W. Loop 281, Longview, Texas, 75603 Vessel constructed by at

Date

July 21, 2015 have inspected the component described in this Manufacturer's Data Report on

07/21/2015 Commissions 15305A

October 14, 2015

Norris Cylinder Company

2325609 exe: v6.2.47

FORM U1-A (Back) NB Number 46678-46689

25905

3. Location of installation Unknown

As Required by the Provisions of the ASME Boiler and Pressure Vessel Code Rules, Section VIII, Division 1

(National Board number)

(Horizontal, vertical, or sphere)

46678-46689

GS146678 to GS146689

(Tank, separator, heat exch., etc.)

8BA711

Norris Control # D298-23

Certificate of Authorization: Type "U" No. 25905 Expires

Date 07/21/2015 Name (Manufacturer)

Commissions:

15305A

(07/13) exe: v6.2.47 2325609

Additional Remarks:

FORM U-4 MANUFACTURER'S DATA REPORT SUPPLEMENTARY SHEET

Corrected

Copy

137931-1

(Alternative Form for Single Chamber, Completely Shop or Field Fabricated Vessels Only)

As Required by the Provisions of the ASME Boiler and Pressure Vessel Code Rules, Section VIII, Division 1

(National Board number) (Horizontal or vertical, tank)

6. Shell:

[Long. (welded, dbl., sngl., lap, butt)] [R.T.(spot or full)] (Eff.,%) (H.T. temp) (Time, hr) [Girth. (welded, dbl., sngl., lap, butt)] [R.T. (spot or full)]

12. Remarks: Manufacturer's Partial Data Reports properly identified and signed by Commissioned Inspectors, have been furnished for the following items of the report:

137931-5

46716-46727 GS146716 to GS146727

Material

Washer (OD, ID, thk)

Location (Top, Bottom, Ends)

Minimum Thickness

Hemispherical Radius

No.

Diameter or Size

Type

Material

Nozzle Flange

Nozzle Thickness

Nom. Corr.

Reinforcement

Material Attachment Details

S/N:

GS146725,GS146722,

GS146723, GS146719,

GS146721, GS146716.

Andrea 01/10/18 10:24:32: S/N:

GS146725,GS146722,

GS146723, GS146719,

GS146721, GS146716.

I, the undersigned, holding a valid commission issued by The National Board of Boiler and Pressure Vessel Inspectors and employed by and state that, to the best of my knowledge and belief, the Manufacturer has constructed this pressure vessel in accordance with ASME BOILER

AND PRESSURE VESSEL CODE, Section VIII, Division 1. By signing this certificate neither the Inspector nor his/her employer makes any warranty, expressed or implied, concerning the pressure vessel described in this Manufacturer's Data Report. Furthermore, neither the Inspector nor his/her employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with

We certify that the statements made in this report are correct and that all details of design, material, construction, and workmanship of this vessel conform to the ASME BOILER AND PRESSURE VESSEL CODE, Section VIII, Division 1. "U" Certificate of Authorization Number

Date 07/21/2015

Vessel constructed by at

Date

July 21, 2015 have inspected the component described in this Manufacturer's Data Report on

07/21/2015 Commissions 15305A

2325611 exe: v6.2.47

FORM U1-A (Back) NB Number 46716-46727

As Required by the Provisions of the ASME Boiler and Pressure Vessel Code Rules, Section VIII, Division 1

46716-46727

GS146716 to GS146727

(Manufacturer) exe: v6.2.47 2325611

137931-5

(Alternative Form for Single Chamber, Completely Shop or Field Fabricated Vessels Only)

As Required by the Provisions of the ASME Boiler and Pressure Vessel Code Rules, Section VIII, Division 1

(National Board number) (Horizontal or vertical, tank)

6. Shell:

[Long. (welded, dbl., sngl., lap, butt)] [R.T.(spot or full)] (Eff.,%) (H.T. temp) (Time, hr) [Girth. (welded, dbl., sngl., lap, butt)] [R.T. (spot or full)]

12. Remarks: Manufacturer's Partial Data Reports properly identified and signed by Commissioned Inspectors, have been furnished for the following items of the report:

138518-4

46975-46986 GS146975 to GS146986

Material

Washer (OD, ID, thk)

Location (Top, Bottom, Ends)

Minimum Thickness

Hemispherical Radius

No.

Diameter or Size

Type

Material

Nozzle Flange

Nozzle Thickness

Nom. Corr.

Reinforcement

Material Attachment Details

S/N:

GS146977, GS146986,

GS146981,GS146975,

GS146979.

Andrea 01/10/18 10:27:58: S/N:

GS146977, GS146986,

GS146981,GS146975,

GS146979.

I, the undersigned, holding a valid commission issued by The National Board of Boiler and Pressure Vessel Inspectors and employed by and state that, to the best of my knowledge and belief, the Manufacturer has constructed this pressure vessel in accordance with ASME BOILER

AND PRESSURE VESSEL CODE, Section VIII, Division 1. By signing this certificate neither the Inspector nor his/her employer makes any warranty, expressed or implied, concerning the pressure vessel described in this Manufacturer's Data Report. Furthermore, neither the Inspector nor his/her employer shall be liable in any manner for any personal injury or property damage or a loss of any kind arising from or connected with

We certify that the statements made in this report are correct and that all details of design, material, construction, and workmanship of this vessel conform to the ASME BOILER AND PRESSURE VESSEL CODE, Section VIII, Division 1. "U" Certificate of Authorization Number

Date 09/09/2015

Vessel constructed by at

Date

September 10, 2015 have inspected the component described in this Manufacturer's Data Report on

09/10/2015 Commissions 15305A

2361677 exe: v6.2.54

FORM U1-A (Back) NB Number 46975-46986

As Required by the Provisions of the ASME Boiler and Pressure Vessel Code Rules, Section VIII, Division 1

46975-46986

GS146975 to GS146986

Date 09/09/2015 Name (Manufacturer)

Date 09/10/2015 Name exe: v6.2.54 2361677

138518-4

ASME Test Reports for AHP Receivers v1_0.pdf