F1T0DC9175A102_Rolling_ESD_Workbenches_Salient_Characteristics.docx

ESD Work Bench – Roll-Around 6/14/2019 Roll-Around ESD Work Bench

Please cost estimate each Roll-Around ESD Work Bench as separate line item grouping (60”, 48”, 36”).

60” Length: Quantity (2), no risers. No nesting required.

48” Length: Quantity (4), no risers. Must nest under Powered-Riser ESD Work Bench.

36” Length (Special Order): Quantity (2), no risers. Must nest under Powered-Riser ESD Work Bench.

Each Roll-Around ESD Work Bench shall have the following salient characteristics:

1. Total height of ESD Work Bench shall be between 33.50” and 34.50”.

(3.25” casters + 28.60” bench legs + 1.75” work surface = ~33.62”)

2. Total height from floor to underside of work surface shall be between 31.75” and 32.25”.

(3.25” casters + 28.60” bench legs = ~31.87”)

3. Total depth of Work Bench shall be between 27.50” and 30.50”.

a. Depth of ESD work surface shall be between 27.50” and 30.50”

4. Bench legs shall consist of the following:

a. Total height equal to 28.60” (SGBL1556)

b. Non-adjustable height

c. Welded plate with mounting holes for plate casters

5. Caster wheels shall consist of the following:

a. Total height equal-to-or-less-than 3.25” (AU-BL-002-01)

b. 2.0” hard rubber wheels with swiveling capability

c. Single caster weight capacity equal-to-or-greater-than 200 lbs

6. Power strip

a. To be installed underside of the work bench(Model # TBD)

b. Prewired with plug, with color of silver/grey

c. Number of outlets and length of power strip proportional to riser length

i. 60” bench length = 8 outlets, 48” power strip length

ii. 48” bench length = 8 outlets, 48” strip length, or 8 outlets, 24” strip length

iii. 36” bench length = 8 outlets, 24” power strip length

7. ESD cable kit(s)

a. As required per Work Bench (SGGC1)

8. Stringer support

a. Quantity of 2 per work Bench (Model # TBD)

9. ESD work surfaces shall consist of the following:

a. ESD Static Dissipative with a bullnose front edge

b. Constructed from laminate over particle board

10. ESD Work Bench shall meet the following ESD criteria:

a. Tested and certified at an open circuit voltage of 100 volts per the ESD Association.

b. Perform within the static dissipative range of 10^6 to 10^9 ohms.

i. The point (surface) to point (surface) resistance shall be greater than or equal to 1 x 106 W (1,000,000 ohms) and less than or equal to 1 x 10 9 W (1,000,000,000 ohms) when tested at 100 V DC.

ii. The point (surface) to ground point resistance shall be greater than or equal to 1 x 10 6 W (1,000,000 ohms) and less than or equal to 1 x 10 9 W (1,000,000,000 ohms) when tested at 100 V DC.

c. Compliance with the following US military guidelines: HDBK-263A, MIL-STD-1686A, MIL-HDBK-773, MIL-STD-W-87893A, T.O. 00-25-234 Section VII, AFMCI 21-XXX, MIL-STD-129.

11. Color of Work Bench shall consist of the following:

a. Metal structural components of work benches shall be painted black.

b. Laminated work surfaces shall be non-painted white.