F1T0DC9175A102_ESD_Workbenches_with_Risers_Salient_Characteristics.docx

ESD Work Bench - Powered Riser 6/14/2019 Powered Riser ESD Work Bench

Please cost estimate each ESD Work Bench as a separate line item grouping (60”, 72”, 45”).

60” Length: Quantity (9) with 20” Fixed Powered Riser (20 Amp) 72” Length: Quantity (2) with 20” Fixed Powered Riser (20 Amp) 45” Length (Special Order): Quantity (2) with 20” Fixed Powered Riser (20 or 15 Amp, per availability)

Each Powered-Riser ESD Work Bench shall have the following salient characteristics:

1. Total height of ESD Work Bench shall be between 58.0” and 60.0”.

(3.25” casters + 31.75” bench legs + 1.75” work surface + 20.0” riser + 1.75” riser top = ~58.52”)

2. Total height from floor to underside of work surface shall be between 34.75” and 35.25”.

(3.25” casters + 31.75” bench legs = ~35.02”)

3. Total depth of ESD Work Bench shall be between 27.50” and 30.50”.

a. Depth of ESD work surface shall be between 27.50” and 30.50”

4. Bench legs shall consist of the following:

a. Total height equal to 31.75” (SGBL1756)

b. Non-adjustable height

c. Welded plate with mounting holes for plate casters

5. Caster wheels shall consist of the following:

a. Total height equal-to-or-less-than 3.25” (AU-BL-002-01)

b. 2.0” hard rubber wheels with swiveling capability

c. Single caster weight capacity equal-to-or-greater-than 200 lbs

6. Fixed Powered Riser shall consist of the following:

a. Riser height shall be between 19.75” and 22.25” (20.0” Model # TBD)

b. Riser depth shall be between 11.75” and 18.25” (Model # TBD)

c. 20 Amp power on uprights (4 outlets, 2 duplex each side), power switch, and GFCI

i. Exception: 45” length can be 15 Amp if 20 Amp power is not available

7. ESD top above riser shall consist of the following:

a. Dimensions depend on Riser dimensions (SDTOP-Variable)

8. Power strip

a. To be installed underside of the riser (Model # TBD)

b. Prewired with plug, with color of silver/grey

c. Number of outlets and length of power strip proportional to riser length

i. 60” riser = 8 outlets, 48” power strip length

ii. 72” riser = 9 outlets, 72” power strip length, or 8 outlets, 48” power strip length

iii. 45” riser = 8 outlets, 24” power strip length

9. LED light bar

a. To be installed underside of the riser (Model # TBD)

b. Length of light bar proportional to riser length

10. Back Stop

a. Quantity of 1 for ESD Work Surface (Model # TBD)

b. Quantity of 1 for ESD Riser Top (Model # TBD)

11. Remove End Stop (SGES330)

12. ESD cable kit(s)

a. As required per Work Bench (SGGC1)

13. Stringer support

a. Quantity of 2 per Work Bench (Model # TBD)

14. Corner splice kit

a. Quantity of 3 total (Model # TBD)

15. ESD work surfaces and ESD tops shall consist of the following:

a. ESD Static Dissipative with a bullnose front edge

b. Constructed from laminate over particle board

16. ESD Work Bench shall meet the following ESD criteria:

a. Tested and certified at an open circuit voltage of 100 volts per the ESD Association.

b. Perform within the static dissipative range of 10^6 to 10^9 ohms.

i. The point (surface) to point (surface) resistance shall be greater than or equal to 1 x 106 W (1,000,000 ohms) and less than or equal to 1 x 10 9 W (1,000,000,000 ohms) when tested at 100 V DC.

ii. The point (surface) to ground point resistance shall be greater than or equal to 1 x 10 6 W (1,000,000 ohms) and less than or equal to 1 x 10 9 W (1,000,000,000 ohms) when tested at 100 V DC.

c. Compliance with the following US military guidelines: HDBK-263A, MIL-STD-1686A, MIL-HDBK-773, MIL-STD-W-87893A, T.O. 00-25-234 Section VII, AFMCI 21-XXX, MIL-STD-129.

17. Color of Work Bench shall consist of the following:

a. Metal structural components of workstations shall be painted black.

b. Laminated work surfaces shall be non-painted white.