DMES_60X60X15 ASSEMBLY REV D.pdf

DRAWING INDEX

SHEET DWG NO TITLE

1 CS-01 COVER SHEET

2 AS-01 ENCLOSURE FRAME ASSEMBLY

3 G-01 ITEM LIST

REVISION DESCRIPTION

REV DESCRIPTION

D DMES BASE WAS WIDENED AND FILLET WELD SIZE IN CORNER CHANGED DUE TO ISSUES WITH 60X60X15 APX ENCLOSURE NOT FITTING BETWEEN UPRGIHTS. A SPACER WAS ADDED TO PREVENT THE UPPER ENCLOSURE FRAME HORIZONTAL SUPPORT FROM BENDING DURING ASSEMBLY. MOUNTING HOLE PATTERN 1 WAS ELIMINATED FOR BEING UNNECESSARY.

DESIGN BY BLS 03/10

DRAWN BY BLS 06/14

APPROVED BY --- MM/YY

REVISION BY CCE 10/22 NOAA / NOS / CO-OPS

REVISION

PROJECT STATUS

DMES_60X60X15 ASSEMBLY

Components

STATION STRUCTURAL COMPONENTS

D

PRODUCTION CS-01 1/3

COVER SHEET

ISO OVERVIEW

DMES ASSEMBLY

SEE SH AS-01 FOR DETAILS

SEE GENERAL NOTES 1-6

GENERAL NOTES

1. THIS DRAWING SUPPLEMENTS THE 'DMES_60X60X15 ASSEMBLY, REV D.STEP' FILE.

2. THIS ASSEMBLY SUPPLEMENTS THE FABRICATION DRAWING 'DMES_60X60X15, REV D'.

3. THIS ASSEMBLY APPROX WEIGHT IS: 237 LBS.

4. ALL DIMENSIONS ARE IN INCHES AND FEET UNLESS OTHERWISE STATED.

5. ABBREVIATIONS USED IN THIS DRAWING ARE AS FOLLOWS:

(N) = NEW (E) = EXISTING SH = SHEET GEN = GENERAL

TYP = TYPICAL EA = EACH ABV = ABOVE PL = PLACES

REF = REFERENCE

6. POC: (240) 533-0494, NOAA, SILVER SPRING, MD

DO NOT SCALE DRAWING

DRAWING SIZE ANSI A NOAA / NOS / CO-OPS

REVISION

PROJECT STATUS

DMES_60X60X15 ASSEMBLY

Components

STATION STRUCTURAL COMPONENTS

D

PRODUCTION AS-01 2/3

ENCLOSURE FRAME

ASSEMBLY

A A

(65.75 REF)

(20.25 REF)

SHEET NOTES

1. ENCLOSURE CLAMPS ARE ATTACHED AFTER THE ENCLOSURE IS BOLTED OT THE

ENCLOSURE FRAME BASE. SEE ISOMETRIC VIEW FOR DETAILS.

2. LEGS ARE TO BE ANCHORED USING 3/4-10UNC SS316 ANCHORS. EMBEDMENT SHLL BE

SPECIFIED ON INSTALLATION DRAWING.

3. INSTALLATION DRAWING REFERS TO A SEPARATE DRAWING THAT CALLS FOR THIS

ASSEMBLY TO BE INSTALLED.

4. CONTACT DDET PRIOR TO USING THIS DESIGN SO DESIGN CRITERIA CAN BE VERIFIED.

(82.4 REF)

(2 PL)

(3, 2 PL)

(6, 2 PL)

(3, 2 PL)

(3, 2 PL)

(3, 2 PL)

(4, 2 PL)

(4, 2 PL)

(4, 2 PL)

(2, 2 PL)

(2 PL)

(2 PL)

(3 PL)

(3 PL)

(6 PL)

(2, 6 PL)

ISOMETRIC VIEW

DMES ASSEMBLY

SEE SHEET NOTES 1-4

FRONT VIEW

DMES ASSEMBLY

SEE SHEET NOTES 1-4

SECTION A-A

ENCLOSURE INTERNAL BOLT DOWN

SEE SHEET NOTE 1

THREADED END ON

BOTTOM, USE

LIQUIDTIGHT TO

CONNECT TO

ENCLOSURE (ITEM 5)

B

B

SECTION B-B

SPACER INSTALL

(2, 3PL)

(3 PL)

(INSTALL PRIOR TO

TIGHTENING DOWN ITEM 2)

USE EPOXY TO ATTACH

1/8 THICK BEARING PAD

TO THESE SURFACES ON THE

INSIDE AREA OF CLAMP THAT

MATES TO ENCLOSURE TOP

ITEM LIST

ITEM QTY DESCRIPTION REMARKS

1 1 DMES FRAME SEE DRAWING 'DMES_60X60X15, REV D' ITEM 1 FOR

DETAILS

2 3 ENCLOSURE CLAMP SEE DRAWING 'DMES_60X60X15, REV D' ITEM 2 FOR

DETAILS

3 1 SPACER SEE DRAWING 'DMES_60X60X15, REV D' ITEM 3 FOR

DETAILS

4 2 ENCLOSURE BOLT DOWN BAR SEE DRAWING 'DMES_60X60X15, REV D' ITEM 4 FOR

DETAILS

5 1 60X60X15 APX ENCLOSURE -

6 3 1/2-13UNC X 18 LG, THREADED ROD, SS316 -

7 9 1/2 WASHER, SS316 -

8 18 1/2-13UNC NUT, SS316 -

9 6 3/4-10UNC X 2-1/2 LG, FULLY THREADED HEX HD SCREW,

SS316 -

10 12 3/4 WASHER, SS316 -

11 6 3/4 WASHER, NYLON -

12 6 3/4 SPLIT WASHER, SS316 -

13 6 3/4-10UNC NUT, SS316 -

14 2 1-1/2 NPS SCH 80, 10' LG, THREADED ONE END, 6061-T6 AL -

15 2 WEATHERHEAD, 1-1/2 CONDUIT SIZE, AL -

16 4 U-BOLT, 3/8-16UNC THREAD X 2 ID, SS316 -

17 8 3/8 WASHER, SS316 -

18 8 3/8 SPLIT WASHER, SS316 -

19 8 3/8-16UNC NUT, SS316 -

NOAA / NOS / CO-OPS

REVISION

PROJECT STATUS

DMES_60X60X15 ASSEMBLY

Components

STATION STRUCTURAL COMPONENTS

D

PRODUCTION G-01 3/3

ITEM LIST