BT238-W8 revA.pdf

Model # BT238-W8

8/21/2020 Page 1 of 10

Owners and installers please note these safety warnings and make use of this checklist on a regular basis.•

Follow installation instructions when erecting equipment.•

Ground surfaces around equipment should be restored as needed. Concrete footings should never be exposed. Surface depth • should comply with ASTM and CPSC specifications.

Check for and repair damage caused by wear or vandalism, a major factor in injury causing situations.•

All protruding bolts should be covered or cut off and finished smooth. Sharp edges on pipes should be capped or removed. Check • for bent, broken, or severely worn pipe, and replace.

All equipment should be free of rust and repainted whenever necessary to deter rusting.•

We provide our customers with layout sheets and installation instructions. Please keep on file the specifications sheet that contains • the listing of every part used.

Never add components not intended for use with this product.•

Regular maintenance is necessary in this and all park and recreational equipment to insure the safety of the user.•

Note: Proper maintenance of equipment requires regular tightening of all bolts, nuts, and setscrews.•

Note: Regular checking of all parts, castings, etc. should be made. If a part is broken or worn, it should be replaced immediately.•

Check to be sure all fittings are tight and that bars and pipes do not move.•

Replace all worn S-hooks. S-hooks must be completely closed. Failure to close S-hooks can result in serious injury to the user. • NEVER reuse S-hooks.

Test for free movement of swing hanger and other moving attached parts.•

Check for worn chains and replace them.•

A soft resilient surface should be placed under all swings extending at least twice the height of the top rail both front and back. •

SAFETY WARNINGS & EQUIPMENT INSPECTION

8/21/2020 Page 2 of 10

3/8" x 2-1/4" Carriage Bolt

3/8" Hex Nut

3/8" x 5" Machine Bolt

800-45-ULTRA www.ultra-site.com

HARDWARE

3/8" Washer

3/8" x 1-1/4" Carriage Bolt

3/8" x 3" Carriage Bolt

8/21/2020 Page 3 of 10

800-45-ULTRA www.ultra-site.com

9/16" Wrench 9/16" Socket Wrench Tape Measure Level

TOOLS REQUIRED

8/21/2020 Page 4 of 10

ULTRA SITE PRODUCT SPECIFICATIONS

BT238-W8

8’ PORTABLE BOLT TOGETHER PICNIC TABLE WALK-THROUGH DESIGN

Top & Seats: Pressure Treated - 2" x 10" No. 1 Southern Yellow Pine pressure treated lumber.

Redwood Stain - 2" x 10" No. 1 Southern Yellow Pine with a redwood stain wood preservative Untreated - 2" x 10" No.1 Southern Yellow Pine

Frame: 2-3/8” O.D. x 12 gauge pre-galvanized structural steel tubing. One 1 1/2" x 3/4" x 1/8" center channel shall be mechanically attached to the bottom side of tabletop to prevent warping of wood and to attach cross braces, thus providing over all strength and rigidity. Cross braces 1 5/16” O.D. x 14 gauge pre-galvanized structural steel tubing. All seat mounting brackets shall be precision punched and fabricated from 10 gauge formed angle. All top mounting brackets shall be precision punched and fabricated from 7g gauge formed angle. Legs are bent over a mandrel through the bend radius producing a wrinkle free bend.

Frame Coating: Electrostatic powder coated application oven cured or hot dipped galvanized.

Hardware: Hardware shall be hot-dipped galvanized or zinc coated.

Dimensions: 8’ portable bolt together picnic table walk-through design. Top is 28-1/4” wide x 96” long and is 30-1/2” high. Seats are 9- 1/4” wide x 96” long and 18-7/16” high. Outside to outside dimension is 62-1/8” x 96”.

8/21/2020 Page 5 of 10

ITEM NO. PartNo DESCRIPTION Qty.

1 01-04-0524 new BT238 wood leg 4 2 01-04-0506 wood table top angle (new) 2 3 01-04-0521 BT Seat Bracket (Left) 2 4 01-04-0522 BT Seat Bracket (Right) 2 5 XXX96-2x10-S1 2 x 10 Pressure Treated/Untreated/Redwood Stained Seat Plank (8') 2 6 XXX96-2x10-T1 2 x 10 Pressure Treated/Untreated/Redwood Stained Top Plank (8') 3 7 01-04-0507 center c channel 3 slot (new) 1 8 01-04-0508 wood table center bracket 1 9 01-04-0523 34-3/4" wood brace 2

10 33-06-0113 3/8" x 2-1/4" Carriage Bolt (Galv) 23 11 33-06-0008 3/8" x 3" Carriage Bolt (Zinc) 12 12 33-02-0002 3/8" Zinc Plated Washer 16 13 33-05-0083 3/8" x 5" Machine Bolt (Zinc) 2 14 33-02-0010 3/8" Galvanized Steel Flat Washer 25 15 33-01-0015 3/8" Hex Nut (GALV) 25 16 33-01-0002 3/8" Hex Nut (Zinc) 14 17 33-06-0114 3/8" x 1-1/4" Carriage Bolt (Galv) 2

9 7

800-45-ULTRA www.ultra-site.com

COMPONENTS

8/21/2020 Page 6 of 10

Attach the Seat Brackets and Top Angles to the 238 Frames as shown using specified hardware.

800-45-ULTRA www.ultra-site.com

STEP 1

8/21/2020 Page 7 of 10

STEP 2

Attach the Wood Center Bracket, C-Channel, and the Wood Planks as shown using specified hardware.

8/21/2020 Page 8 of 10

STEP 3

13 12 16

817 14 15

Attach the 34-3/4" Braces to the Wood Center bracket and the 238 Frames as shown using specified hardware.

8/21/2020 Page 9 of 10

OVERALL DIMENSIONS

96"

9 1/4"

60 5/16"

28 1/4"

62 1/8"

18 7/16"

30 9/16"

8/21/2020 Page 10 of 10