Grease_SDS.xml

WWIUSER Microsoft Word - r9764854.rtf 1910.1200 Version 11.4 Revision Date: 01/15/2016 Print Date: 01/16/2016 SECTION 1. IDENTIFICATION Product name : AeroShell Grease 22 Product code : 001A0059 Manufacturer or supplier's details Manufacturer/Supplier : Shell Oil Products US PO Box 4427 Houston TX 77210-4427 USA SDS Request : (+1) 877-276-7285 Customer Service : Emergency telephone number Spill Information : 877-504-9351 Health Information : 877-242-7400 Recommended use of the chemical and restrictions on use Recommended use : Synthetic grease for aircraft., For further details consult the AeroShell Book on www.shell.com/aviation. SECTION 2. HAZARDS IDENTIFICATION GHS Classification Not a hazardous substance or mixture. GHS label elements Hazard pictograms : No Hazard Symbol required Signal word : No signal word Hazard statements : PHYSICAL HAZARDS: Not classified as a physical hazard under GHS criteria. HEALTH HAZARDS: Not classified as a health hazard under GHS criteria. ENVIRONMENTAL HAZARDS: Not classified as an environmental hazard under GHS criteria. Precautionary statements : Prevention: No precautionary phrases. Response: No precautionary phrases. Storage: No precautionary phrases. Disposal: No precautionary phrases. Other hazards which do not result in classification 1910.1200 Version 11.4 Revision Date: 01/15/2016 Print Date: 01/16/2016 Prolonged or repeated skin contact without proper cleaning can clog the pores of the skin result- ing in disorders such as oil acne/folliculitis. Used grease may contain harmful impurities. High-pressure injection under the skin may cause serious damage including local necrosis. Not classified as flammable but will burn. The classification of this material is based on OSHA HCS 2012 criteria. Under normal conditions of use or in a foreseeable emergency, this product does not meet the definition of a hazardous chemical when evaluated according to the OSHA Hazard Communica- tion Standard, 29 CFR 1910.1200. SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS Chemical nature : Synthetic hydrocarbon oil grease thickened with clay, contain- ing additives. Hazardous components Chemical name Synonyms CAS-No. Concentration (%) Alkaryl amine 36878-20-3 1 - 3 Aryl amine N-[(1,1,3,3-tetramethyl- bu- tyl)phenyl]naphthale n-1-amine 51772-35-1 1 - 3 SECTION 4. FIRST-AID MEASURES General advice : Not expected to be a health hazard when used under normal conditions. If inhaled : No treatment necessary under normal conditions of use. If symptoms persist, obtain medical advice. In case of skin contact : Remove contaminated clothing. Flush exposed area with wa- ter and follow by washing with soap if available. If persistent irritation occurs, obtain medical attention. When using high pressure equipment, injection of product under the skin can occur. If high pressure injuries occur, the casualty should be sent immediately to a hospital. Do not wait for symptoms to develop. Obtain medical attention even in the absence of apparent wounds. In case of eye contact : Flush eye with copious quantities of water. If persistent irritation occurs, obtain medical attention. If swallowed : In general no treatment is necessary unless large quantities are swallowed, however, get medical advice. Most important symptoms and effects, both acute and : Oil acne/folliculitis signs and symptoms may include formation of black pustules and spots on the skin of exposed areas. 1910.1200 Version 11.4 Revision Date: 01/15/2016 Print Date: 01/16/2016 delayed Ingestion may result in nausea, vomiting and/or diarrhoea. Local necrosis is evidenced by delayed onset of pain and tissue damage a few hours following injection. Protection of first-aiders : When administering first aid, ensure that you are wearing the appropriate personal protective equipment according to the incident, injury and surroundings. Immediate medical attention, special treatment : Treat symptomatically. High pressure injection injuries require prompt surgical inter- vention an d possibly steroid therapy, to minimise tissue dam- age and loss of function. Because entry wounds are small and do not reflect the seri- ousness of the underlying damage, surgical exploration to determine the extent of involvement may be necessary. Local anaesthetics or hot soaks should be avoided because they can contribute to swelling, vasospasm and ischaemia. Prompt surgical decompression, debridement and evacuation of for- eign material should be performed under general anaesthet- ics, and wide exploration is essential. SECTION 5. FIRE-FIGHTING MEASURES Suitable extinguishing media : Foam, water spray or fog. Dry chemical powder, carbon diox- ide, sand or earth may be used for small fires only. Unsuitable extinguishing media : Do not use water in a jet. Specific hazards during fire- fighting : Hazardous combustion products may include: A complex mixture of airborne solid and liquid particulates and gases (smoke). Carbon monoxide may be evolved if incomplete combustion occurs. Unidentified organic and inorganic compounds. Specific extinguishing meth- ods : Use extinguishing measures that are appropriate to local cir- cumstances and the surrounding environment. Special protective equipment for firefighters : Proper protective equipment including chemical resistant gloves are to be worn; chemical resistant suit is indicated if large contact with spilled product is expected. Self-Contained Breathing Apparatus must be worn when approaching a fire in a confined space. Select fire fighter's clothing approved to relevant Standards (e.g. Europe: EN469). SECTION 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protec- tive equipment and emer- gency procedures : Avoid contact with skin and eyes. 1910.1200 Version 11.4 Revision Date: 01/15/2016 Print Date: 01/16/2016 Environmental precautions : Use appropriate containment to avoid environmental contami- nation. Prevent from spreading or entering drains, ditches or rivers by using sand, earth, or other appropriate barriers. Methods and materials for containment and cleaning up : Prevent from spreading or entering into drains, ditches or riv- ers by using sand, earth, or other appropriate barriers. Additional advice : For guidance on selection of personal protective equipment see Chapter 8 of this Safety Data Sheet. For guidance on disposal of spilled material see Chapter 13 of this Safety Data Sheet. SECTION 7. HANDLING AND STORAGE Technical measures : Use local exhaust ventilation if there is risk of inhalation of vapours, mists or aerosols. Use the information in this data sheet as input to a risk as- sessment of local circumstances to help determine appropri- ate controls for safe handling, storage and disposal of this material. Precautions for safe handling : Avoid prolonged or repeated contact with skin. Avoid inhaling vapour and/or mists. When handling product in drums, safety footwear should be worn and proper handling equipment should be used. Properly dispose of any contaminated rags or cleaning mate- rials in order to prevent fires. Avoidance of contact : Strong oxidising agents. Storage Recommended storage tem- perature : -50 - 50 °C Other data : Keep container tightly closed and in a cool, well-ventilated place. Use properly labeled and closable containers. Packaging material : Suitable material: For containers or container linings, use mild steel or high density polyethylene. Unsuitable material: PVC. Container Advice : Polyethylene containers should not be exposed to high tem- peratures because of possible risk of distortion. SECTION 8. EXPOSURE CONTROLS AND PERSONAL PROTECTION Components with workplace control parameters Biological occupational exposure limits 1910.1200 Version 11.4 Revision Date: 01/15/2016 Print Date: 01/16/2016 No biological limit allocated. Monitoring Methods Monitoring of the concentration of substances in the breathing zone of workers or in the general workplace may be required to confirm compliance with an OEL and adequacy of exposure con- trols. For some substances biological monitoring may also be appropriate. Validated exposure measurement methods should be applied by a competent person and sam- ples analysed by an accredited laboratory. Examples of sources of recommended exposure measurement methods are given below or con- tact the supplier. Further national methods may be available. National Institute of Occupational Safety and Health (NIOSH), USA: Manual of Analytical Methods http://www.cdc.gov/niosh/ Occupational Safety and Health Administration (OSHA), USA: Sampling and Analytical Methods http://www.osha.gov/ Health and Safety Executive (HSE), UK: Methods for the Determination of Hazardous Substances http://www.hse.gov.uk/ Institut für Arbeitsschutz Deutschen Gesetzlichen Unfallversicherung (IFA) , Germany http://www.dguv.de/inhalt/index.jsp L'Institut National de Recherche et de Securité, (INRS), France http://www.inrs.fr/accueil Engineering measures : The level of protection and types of controls necessary will vary depending upon potential exposure conditions. Select controls based on a risk assessment of local circumstances. Appropriate measures include: Adequate ventilation to control airborne concentrations. Where material is heated, sprayed or mist formed, there is greater potential for airborne concentrations to be generated. General Information: Define procedures for safe handling and maintenance of controls. Educate and train workers in the hazards and control measures relevant to normal activities associated with this product. Ensure appropriate selection, testing and maintenance of equipment used to control exposure, e.g. personal protective equipment, local exhaust ventilation. Drain down system prior to equipment break-in or mainte- nance. Retain drain downs in sealed storage pending disposal or subsequent recycle. Always observe good personal hygiene measures, such as washing hands after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Discard con- taminated clothing and footwear that cannot be cleaned. Practice good housekeeping. Personal protective equipment Respiratory protection : No respiratory protection is ordinarily required under normal conditions of use. In accordance with good industrial hygiene practices, precau- tions should be taken to avoid breathing of material. If engineering controls do not maintain airborne concentra- 1910.1200 Version 11.4 Revision Date: 01/15/2016 Print Date: 01/16/2016 tions to a level which is adequate to protect worker health, select respiratory protection equipment suitable for the spe- cific conditions of use and meeting relevant legislation. Check with respiratory protective equipment suppliers. Where air-filtering respirators are suitable, select an appro- priate combination of mask and filter. Select a filter suitable for the combination of organic gases and vapours [Type A/Type P boiling point >65°C (149°F)]. Hand protection Remarks : Where hand contact with the product may occur the use of gloves approved to relevant standards (e.g. Europe: EN374, US: F739) made from the following materials may provide suitable chemical protection. PVC, neoprene or nitrile rubber gloves Suitability and durability of a glove is dependent on usage, e.g. frequency and duration of contact, chemical re- sistance of glove material, dexterity. Always seek advice from glove suppliers. Contaminated gloves should be replaced. Personal hygiene is a key element of effective hand care. Gloves must only be worn on clean hands. After using gloves, hands should be washed and dried thoroughly. Appli- cation of a non-perfumed moisturizer is recommended. For continuous contact we recommend gloves with break- through time of more than 240 minutes with preference for > 480 minutes where suitable gloves can be identified. For short-term/splash protection we recommend the same, but recognize that suitable gloves offering this level of protection may not be available and in this case a lower breakthrough time maybe acceptable so long as appropriate maintenance and replacement regimes are followed. Glove thickness is not a good predictor of glove resistance to a chemical as it is dependent on the exact composition of the glove material. Glove thickness should be typically greater than 0.35 mm depending on the glove make and model. Eye protection : If material is handled such that it could be splashed into eyes, protective eyewear is recommended. Skin and body protection : Skin protection is not ordinarily required beyond standard work clothes. It is good practice to wear chemical resistant gloves. Protective measures : Personal protective equipment (PPE) should meet recom- mended national standards. Check with PPE suppliers. Environmental exposure controls General advice : Take appropriate measures to fulfill the requirements of rele- vant environmental protection legislation. Avoid contamination of the environment by following advice given in Chapter 6. If necessary, prevent undissolved material from being dis- charged to waste water. Waste water should be treated in a municipal or industrial waste water treatment plant before discharge to surface water. Local guidelines on emission limits for volatile substances must be observed for the discharge of exhaust air containing vapour. 1910.1200 Version 11.4 Revision Date: 01/15/2016 Print Date: 01/16/2016 SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance : Semi-solid at ambient temperature. Colour : amber Odour : Slight hydrocarbon Odour Threshold : Data not available pH : Not applicable Drop point : >= 260 °C / >= 500 °FMethod: Unspecified Initial boiling point and boiling range : Data not available Flash point : >= 230 °C / >= 446 °F Method: ASTM D92 Evaporation rate : Data not available Flammability (solid, gas) : Data not available Upper explosion limit : Typical 10 %(V) Lower explosion limit : Typical 1 %(V) Vapour pressure : < 0.5 Pa (20 °C / 68 °F) estimated value(s) Relative vapour density : > 1estimated value(s) Relative density : 0.868 (15 °C / 59 °F) Density : 868 kg/m3 (15.0 °C / 59.0 °F) Method: Unspecified Solubility(ies) Water solubility : negligible Solubility in other solvents : Data not available Partition coefficient: n- octanol/water : Pow: > 6(based on information on similar products) Auto-ignition temperature : > 320 °C / 608 °F Viscosity Viscosity, dynamic : Data not available 1910.1200 Version 11.4 Revision Date: 01/15/2016 Print Date: 01/16/2016 Viscosity, kinematic : Not applicable Explosive properties : Not classified Oxidizing properties : Data not available Conductivity : This material is not expected to be a static accumulator. Decomposition temperature : Data not available SECTION 10. STABILITY AND REACTIVITY Chemical stability : Stable. Possibility of hazardous reac- tions : Reacts with strong oxidising agents. Conditions to avoid : Extremes of temperature and direct sunlight. Incompatible materials : Strong oxidising agents. Hazardous decomposition products : Hazardous decomposition products are not expected to form during normal storage. SECTION 11. TOXICOLOGICAL INFORMATION Basis for assessment : Information given is based on data on the components and the toxicology of similar products.Unless indicated otherwise, the data presented is representative of the product as a whole, rather than for individual component(s). Information on likely routes of exposure Skin and eye contact are the primary routes of exposure although exposure may occur following accidental ingestion. Acute toxicity Product: Acute oral toxicity : LD50 (rat): > 5,000 mg/kg Remarks: Expected to be of low toxicity: Acute inhalation toxicity : Remarks: Not considered to be an inhalation hazard under normal conditions of use. Acute dermal toxicity : LD50 (Rabbit): > 5,000 mg/kg Remarks: Expected to be of low toxicity: Skin corrosion/irritation Product: Remarks: Expected to be slightly irritating., Prolonged or repeated skin contact without proper cleaning can clog the pores of the skin resulting in disorders such as oil acne/folliculitis. 1910.1200 Version 11.4 Revision Date: 01/15/2016 Print Date: 01/16/2016 Serious eye damage/eye irritation Product: Remarks: Expected to be slightly irritating. Respiratory or skin sensitisation Product: Remarks: Not expected to be a skin sensitiser. Germ cell mutagenicity Product: : Remarks: Not considered a mutagenic hazard. Carcinogenicity Product: Remarks: Not expected to be carcinogenic. IARC No component of this product present at levels greater than or equal to 0.1% is identified as probable, possible or confirmed human carcinogen by IARC. ACGIH No component of this product present at levels greater than or equal to 0.1% is identified as a carcinogen or potential carcino- gen by ACGIH. OSHA No component of this product present at levels greater than or equal to 0.1% is identified as a carcinogen or potential carcino- gen by OSHA. NTP No component of this product present at levels greater than or equal to 0.1% is identified as a known or anticipated carcinogen by NTP. Reproductive toxicity Product: : Remarks: Not expected to impair fertility., Not expected to be a developmental toxicant. STOT - single exposure Product: Remarks: Not expected to be a hazard. STOT - repeated exposure Product: 1910.1200 Version 11.4 Revision Date: 01/15/2016 Print Date: 01/16/2016 Remarks: Not expected to be a hazard. Aspiration toxicity Product: Not considered an aspiration hazard. Further information Product: Remarks: Used grease may contain harmful impurities that have accumulated during use. The concentration of such harmful impurities will depend on use and they may present risks to health and the environment on disposal., ALL used grease should be handled with caution and skin contact avoided as far as possible. Remarks: High pressure injection of product into the skin may lead to local necrosis if the prod- uct is not surgically removed. Remarks: Slightly irritating to respiratory system. SECTION 12. ECOLOGICAL INFORMATION Basis for assessment : Ecotoxicological data have not been determined specifically for this product. Information given is based on a knowledge of the components and the ecotoxicology of similar products. Unless indicated otherwise, the data presented is representa- tive of the product as a whole, rather than for individual com- ponent(s).(LL/EL/IL50 expressed as the nominal amount of product required to prepare aqueous test extract). Ecotoxicity Product: Toxicity to fish (Acute toxici- ty) : Remarks: Expected to be practically non toxic: LL/EL/IL50 > 100 mg/l Toxicity to daphnia and other aquatic invertebrates (Acute toxicity) : Remarks: Expected to be practically non toxic: LL/EL/IL50 > 100 mg/l Toxicity to algae (Acute tox- icity) : Remarks: Expected to be practically non toxic: LL/EL/IL50 > 100 mg/l Toxicity to fish (Chronic tox- icity) : Remarks: Data not available Toxicity to daphnia and other aquatic invertebrates (Chron- ic toxicity) : Remarks: Data not available Toxicity to bacteria (Acute : Remarks: Data not available 1910.1200 Version 11.4 Revision Date: 01/15/2016 Print Date: 01/16/2016 toxicity) Persistence and degradability Product: Biodegradability : Remarks: Expected to be not readily biodegradable. Major constituents are expected to be inherently biodegrada- ble, but contains components that may persist in the environ- ment. Bioaccumulative potential Product: Bioaccumulation : Remarks: Contains components with the potential to bioac- cumulate. Mobility in soil Product: Mobility : Remarks: Semi-solid under most environmental conditions. If it enters soil, it will adsorb to soil particles and will not be mobile. Remarks: Floats on water. Other adverse effects no data available Product: Additional ecological infor- mation : Product is a mixture of non-volatile components, which are not expected to be released to air in any significant quantities. Not expected to have ozone depletion potential, photochemi- cal ozone creation potential or global warming potential. Poorly soluble mixture. May cause physical fouling of aquatic organisms. SECTION 13. DISPOSAL CONSIDERATIONS Disposal methods Waste from residues : Recover or recycle if possible. It is the responsibility of the waste generator to determine the toxicity and physical properties of the material generated to determine the proper waste classification and disposal meth- ods in compliance with applicable regulations. Do not dispose into the environment, in drains or in water courses Contaminated packaging : Dispose in accordance with prevailing regulations, preferably to a recognized collector or contractor. The competence of the collector or contractor should be established beforehand. Disposal should be in accordance with applicable regional, 1910.1200 Version 11.4 Revision Date: 01/15/2016 Print Date: 01/16/2016 national, and local laws and regulations. Local legislation Remarks : Disposal should be in accordance with applicable regional, national, and local laws and regulations. SECTION 14. TRANSPORT INFORMATION National Regulations US Department of Transportation Classification (49 CFR Parts 171-180) Not regulated as a dangerous good International Regulation IATA-DGR Not regulated as a dangerous good IMDG-Code Not regulated as a dangerous good Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code Pollution category : Not applicable Ship type : Not applicable Product name : Not applicable Special precautions : Not applicable Special precautions for user Remarks : Special Precautions: Refer to Chapter 7, Handling & Storage, for special precautions which a user needs to be aware of or needs to comply with in connection with transport. Additional Information : MARPOL Annex 1 rules apply for bulk shipments by sea. SECTION 15. REGULATORY INFORMATION OSHA Hazards : No OSHA Hazards EPCRA - Emergency Planning and Community Right-to-Know Act CERCLA Reportable Quantity This material does not contain any components with a CERCLA RQ., Shell classifies this material as an "oil" under the CERCLA Petroleum Exclusion, therefore releases to the environment are not reportable under CERCLA. SARA 304 Extremely Hazardous Substances Reportable Quantity This material does not contain any components with a section 304 EHS RQ. SARA 311/312 Hazards : No SARA Hazards 1910.1200 Version 11.4 Revision Date: 01/15/2016 Print Date: 01/16/2016 SARA 302 : No chemicals in this material are subject to the reporting requirements of SARA Title III, Section 302. SARA 313 : This material does not contain any chemical components with known CAS numbers that exceed the threshold (De Minimis) reporting levels established by SARA Title III, Section 313. Clean Water Act This product does not contain any Hazardous Chemicals listed under the U.S. CleanWater Act, Section 311, Table 117.3. Pennsylvania Right To Know diphenylamine 122-39-4 California Prop 65 This product does not contain any chemicals known to State of California to cause cancer, birth defects, or any other re- productive harm. The components of this product are reported in the following inventories: EINECS : All components listed or polymer exempt. TSCA : All components listed. DSL : All components listed. SECTION 16. OTHER INFORMATION Further information NFPA Rating (Health, Fire, Reac- tivity) 0, 1, 0 A vertical bar (|) in the left margin indicates an amendment from the previous version. Abbreviations and Acronyms : The standard abbreviations and acronyms used in this docu- ment can be looked up in reference literature (e.g. scientific dictionaries) and/or websites. ACGIH = American Conference of Governmental Industrial Hygienists ADR = European Agreement concerning the International Carriage of Dangerous Goods by Road AICS = Australian Inventory of Chemical Substances ASTM = American Society for Testing and Materials BEL = Biological exposure limits BTEX = Benzene, Toluene, Ethylbenzene, Xylenes CAS = Chemical Abstracts Service CEFIC = European Chemical Industry Council CLP = Classification Packaging and Labelling COC = Cleveland Open-Cup DIN = Deutsches Institut fur Normung DMEL = Derived Minimal Effect Level DNEL = Derived No Effect Level DSL = Canada Domestic Substance List EC = European Commission 1910.1200 Version 11.4 Revision Date: 01/15/2016 Print Date: 01/16/2016 EC50 = Effective Concentration fifty ECETOC = European Center on Ecotoxicology and Toxicolo- gy Of Chemicals ECHA = European Chemicals Agency EINECS = The European Inventory of Existing Commercial Chemical Substances EL50 = Effective Loading fifty ENCS = Japanese Existing and New Chemical Substances Inventory EWC = European Waste Code GHS = Globally Harmonised System of Classification and Labelling of Chemicals IARC = International Agency for Research on Cancer IATA = International Air Transport Association IC50 = Inhibitory Concentration fifty IL50 = Inhibitory Level fifty IMDG = International Maritime Dangerous Goods INV = Chinese Chemicals Inventory IP346 = Institute of Petroleum test method N° 346 for the determination of polycyclic aromatics DMSO-extractables KECI = Korea Existing Chemicals Inventory LC50 = Lethal Concentration fifty LD50 = Lethal Dose fifty per cent. LL/EL/IL = Lethal Loading/Effective Loading/Inhibitory loading LL50 = Lethal Loading fifty MARPOL = International Convention for the Prevention of Pollution From Ships NOEC/NOEL = No Observed Effect Concentration / No Ob- served Effect Level OE_HPV = Occupational Exposure - High Production Volume PBT = Persistent, Bioaccumulative and Toxic PICCS = Philippine Inventory of Chemicals and Chemical Substances PNEC = Predicted No Effect Concentration REACH = Registration Evaluation And Authorisation Of Chemicals RID = Regulations Relating to International Carriage of Dan- gerous Goods by Rail SKIN_DES = Skin Designation STEL = Short term exposure limit TRA = Targeted Risk Assessment TSCA = US Toxic Substances Control Act TWA = Time-Weighted Average vPvB = very Persistent and very Bioaccumulative Revision Date : 01/15/2016 This information is based on our current knowledge and is intended to describe the product for the purposes of health, safety and environmental requirements only. It should not therefore be construed as guaranteeing any specific property of the product.