Attachment B - Specification P CDT4-1A.pdf

32-Subject Sheet Orientation, Security Threads, Watermarks, and Notch (Type IV Currency Paper - $5 Denomination)

Top (Felt) Side Up

LEADING EDGE

TRAILING EDGE

S

ID

E -G

U

ID

E E

D G

E

Figure 1-D Type IV $5 32-Subject Sheet Orientation

Revision Date: 19Sep09 Supersedes: 16Jul07

Figure 1-D

657 ± 1 mm m m

Notch

E m be d de d

T hr ea d

E m be d de d

T hr ea d

E m be d de d

T hr ea d

E m be d de d

T hr ea d

2 - 4 mm

48 mm

M ac h in e D ire ct io n

163 ± 5 mm

61.5 mm

162.6 mm

109.0 mm

156 mm

66.5 mm

Note: All dimensions are in millimeters (mm).

Security Thread and Watermark Location on Note on 32-Subject Sheet (Type IV Currency Paper – $5 Denomination)

Figure 3-D Type IV $5 Note Layout Revision Date: 19Sep09

Supersedes: 16Jul07

66.5

48.0 ± 3

162.6 ± 3

LEADING EDGE

109.0 ± 4

S

ID

E -G

U

ID

E E

D G

E

Figure 3-D

Embedded Security Thread

38.8 ± 3

61.5 ± 3

1) All dimensions are in millimeters (mm)

2) Watermarks: large numeral 5 and column of three small numeral 5's

3) Large watermark dimensions (nominal): 20 mm (cross direction) x 24 mm (machine direction)

4) Column of small watermarks dimensions (nominal): 6.5 mm (cross direction) x 35 mm (machine direction)

5) Watermarks registration tolerance (cross direction and machine direction): ± 3 mm

6) Embedded thread location tolerance (cross direction from centerline of thread): ± 4 mm

7) Embedded thread width (nominal): 2.0 mm

(Type IV Currency Paper - $10 Denomination)

Top (Felt) Side Up

LEADING EDGE

TRAILING EDGE

S

ID

E -G

U

ID

E E

D G

E

Figure 1-E Type IV $10 32-Subject Sheet Orientation

Revision Date: 19Sep09 Supersedes: 30Sep06

Figure 1-E

657 ± 1 mm m m

Watermark Location

Notch

E m b ed d ed

T hr e ad

E m b ed d ed

T hr e ad

E m b ed d ed

T hr e ad

E m b ed d ed

T hr e ad

2 - 4 mm

156 mm

66.5 mm

45.5 mm

M a ch in e D ir ec tio n

293 ± 5 mm

148 mm

(Type IV Currency Paper – $10 Denomination)

Figure 3-E Type IV $10 Note Layout Revision Date: 19Sep09 Supersedes: 30Sep06

66.5

45.5 ± 3

148.00 ± 3

LEADING EDGE

116.80 ± 4

S

ID

E -G

U

ID

E E

D G

E

Figure 3-E

Embedded Security Thread

1) All dimensions are in millimeters (mm)

2) Watermark: portrait of Alexander Hamilton looking to viewer’s left

3) Watermark dimensions (nominal): 19 mm (cross direction) x 24 mm (machine direction)

4) Watermark registration tolerance (cross direction and machine direction): ± 3 mm

5) Watermark registration reference points are the top of head (hair) and side of head (hair)

7) Embedded thread width (nominal): 1.6 mm

(Type IV Currency Paper - $20 Denomination)

Top (Felt) Side Up

LEADING EDGE

TRAILING EDGE

S

ID

E -G

U

ID

E E

D G

E

Figure 1-F Type IV $20 32-Subject Sheet Orientation

Revision Date: 19Sep09 Supersedes: 03Aug09

Figure 1-F

657 ± 1 mm m m

Watermark Location

Notch

E m b ed d ed

T hr e ad

E m b ed d ed

T hr e ad

E m b ed d ed

T hr e ad

E m b ed d ed

T hr e ad

2 - 4 mm

156 mm

66.5 mm

43 mm

M a ch in e D ir ec tio n

413 ± 5 mm

140 mm

Figure 3-F Type IV $20 Note Layout Revision Date: 19Sep09 Supersedes: 30Sep06

66.5

43 ± 3

138 ± 3

LEADING EDGE

34 ± 4

S

ID

E -G

U

ID

E E

D G

E

Figure 3-F

Embedded Security Thread

Security Thread and Watermark Location on Note on 32-Subject Sheet (Type IV Currency Paper – $20 Denomination)

1) All dimensions are in millimeters (mm)

2) Watermark: portrait of Andrew Jackson looking to viewer’s right

3) Watermark dimensions (nominal): 30 mm (cross direction) x 36 mm (machine direction)

4) Watermark registration tolerance (cross direction and machine direction): ± 3 mm

5) Watermark registration reference points are the top of head (hair) and side of head (hair)

7) Embedded thread width (nominal): 1.6 mm

(Type IV Currency Paper - $50 Denomination)

Top (Felt) Side Up

LEADING EDGE

TRAILING EDGE

S

ID

E -G

U

ID

E E

D G

E

Figure 1-G Type IV $50 32-Subject Sheet Orientation

Revision Date: 19Sep09 Supersedes: 30Sep06

Figure 1-G

657 ± 1 mm m m

Watermark Location

Notch

E m b ed d ed

T hr e ad

E m b ed d ed

T hr e ad

E m b ed d ed

T hr e ad

E m b ed d ed

T hr e ad

2 - 4 mm

156 mm

66.5 mm

43 mm

M a ch in e D ir ec tio n

463 ± 5 mm

138 mm

(Type IV Currency Paper – $50 Denomination)

Figure 3-G Type IV $50 Note Layout Revision Date: 19Sep09 Supersedes: 30Sep06

66.5

43 ± 3

138 ± 3

LEADING EDGE

104 ± 4

S

ID

E -G

U

ID

E E

D G

E

Figure 3-G

Embedded Security Thread

1) All dimensions are in millimeters (mm)

2) Watermark: portrait of Ulysses S. Grant looking to viewer’s right

3) Watermark dimensions (nominal): 22 mm (cross direction) x 34 mm (machine direction)

4) Watermark registration tolerance (cross direction and machine direction): ± 3 mm

5) Watermark registration reference points are the top of head (hair) and side of head (ear)

7) Embedded thread width (nominal): 2.0 mm

S

ID

E -G

U

ID

E E

D G

E

LEADING EDGE

TRAILING EDGE

Figure A Type IV Distinctive Security Threads

Orientation Issue Date: 19Sep09

Figure A

Distinctive Security Threads Orientation for Type IV Currency Paper Denominations

Top (Felt) Side Up

M ac hi ne

D ire ct io n

$5 $10 $20 $50

Note: Not to Scale

ENVIRONMENTAL, HEALTH AND SAFETY FOR MATERIALS

SPECIFICATIONS

ATTACHMENT C– 75.00 (4.4.6) 2.1

C.3.6 ENVIRONMENTAL, HEALTH AND SAFETY REQUIREMENTS

All materials delivered to the BEP shall be designed to minimize all risks of injury & illness to BEP employees. All materials shall be in full compliance with government and commercial environment, safety and health regulations and requirements. The following are specific safety, health and environmental requirements for the acquisition of materials (paper, ink, rigging boards, chemicals, etc.) for the BEP.

C.3.6.1 GENERAL ENVIRONMENT, HEALTH & SAFETY

Materials shall be designed to prevent injury and illness to operation and maintenance personnel at all times. All materials shall comply with the Occupational Health and Safety Administration (OSHA) and Environmental Protection Agency standards. The BEP retains the right to reject any material that may potentially cause an injury or adverse health effect upon its employees.

Injury effects include but are not limited to cuts and punctures. Adverse health effects include, but are not limited to: headache; eye, dermal, nasal, or throat irritation; sensitization; nausea; and dizziness. Before purchasing any materials or chemicals that are not specified in the original contract, the Office of Environment, Health & Safety (DCF) and/or the Environment, Health and Safety Branch (WCF), must review the Specification and/or MSDS for approval.

C.3.6.2 MATERIAL SAFETY DATA SHEET (MSDS)

The contractor shall submit a MSDS for all chemicals and applicable materials to the OEHS for review and approval. The MSDS shall comply with the OSHA regulations set forth in 29 CFR 1910, Part 1200 Hazard Communication (HazCom). The materials are not to be used until written approval is received from the OEHS.

C.3.6.3 HAZARDOUS EMISSIONS

The material shall not emit substances that are hazardous during storage, printing, processing, or any usage. The OSHA HazCom Standard (29 CFR 1910.1200) and its appendices define health hazards and list information sources to be used in establishing which substances at what concentration levels are hazardous.

C.3.6.4 ENVIRONMENTAL PROTECTION REQUIREMENTS

All materials and processes must meet or exceed standards in the regulations and executive orders listed below. Other environmental regulations, executive orders and guidance may also be applicable. The environmental protection

Created on 05/08//2008 - 1 -

ATTACHMENT C– 75.00 (4.4.6) 2.1

requirements focus on emissions, discharges, and waste products impacting air, water, and land.

References:

Federal Regulation: Environmental Protection Agency, EPA Clean Air Act, as Amended

Clean Air Act Amendments of 1990, Section 112 - Air Toxics.

40 CFR 60 - Appendix A - Test Methods.

40 CFR Part 247 - Comprehensive Guideline for Procurement of Products Containing Recovered Materials, May 1, 1996

40 CFR 261 – Identification and Listing of Hazardous Waste

40 CFR 355 --Requirements for Emergency Planning and Notification under CERCLA.

40 CFR 370 --Hazardous Chemical Reporting and Community Right to Know Requirements.

40 CFR 372 -- Toxic Chemical Release Reporting

40 CFR 403 - General Pretreatment Regulations for Existing and New Sources of Pollution

40 CFR 720 – Pre-manufacture Notification: Pre-manufacture Notice Requirements and Review Procedures.

40 CFR 761 -- Polychlorinated Biphenyls (PCBs) Manufacturing, Processing, Distribution in Commerce, and Use Prohibitions.

P.L. 102-486, Energy Policy Act of 1992, October 24, 1992

Executive Order 13423 - Strengthening Federal Environmental, Energy and Transportation Management, January 26, 2007

Superfund Amendments Reauthorization Act (SARA), Title III

District of Columbia Municipal Regulations (DCMR), Title 20, Subtitle A, Air Quality Regulations

District of Columbia Municipal Regulations (DCMR), Title 20, Subtitle E, Hazardous Waste Regulations

District of Columbia Municipal Regulations (DCMR), Title 21, Water and Sanitation, Chapter 15, Discharges to Wastewater System Regulations

Texas Administrative Code (TAC), Title 31, Natural Resources and Conservation, Part III, Air Control Board, Chapter 115, Control of Air Pollution from Volatile Compounds.

Created on 05/08//2008 - 2 -

ATTACHMENT C– 75.00 (4.4.6) 2.1

Texas Administrative Code (TAC), Title 31, Natural Resources and Conservation, Part IX, Texas Water Commission, Chapters 319, 321, and 323, Texas Wastewater Treatment Regulations.

C.3.6.5 Air Emissions

The Contractor shall identify all regulated air pollutants that are ingredients in the product(s) to be purchased by the BEP.

VOCs: Inks are limited to specific limits for volatile organic solvent content (VOC) as specified by the DC Air Quality regulations and other EPA guidelines. Inks may not exceed ink VOC limits. Cleaning materials must meet compliance requirements for the printing applications as specified by the DC Air Quality regulations, 20 DCMR Title A. The vapor pressure limit for organic cleaning solvents is ten (10) millimeters (mm) of Mercury (Hg) (or 1.3332 kPa) at 20 degrees Celsius (oC) or 68 degrees Fahrenheit (oF).

Air Toxics: The material shall not contain, as an ingredient, any of the chemicals regulated as Air Toxics by the Clean Air Act Amendments of 1990, Section 112.

C.3.6.6 Wastewater

Information shall be provided to the OEHS/EHSB through the COTR on the characteristics of all material/effluents (pumpable or gravity flow liquids) that will come from the equipment, either regularly or intermittently, including routine or scheduled maintenance work. This information will be used to determine the feasibility and method of treating the effluents either in the Wastewater Pre- Treatment Plant or requiring that the materials be handled through the Solid/Hazardous Waste Program.

C.3.6.7 Energy/Water/Recovered Materials Usage Policy

The Contractor shall make every effort to provide the most environmentally friendly materials to the Bureau. The Contractor shall comply with:

Executive Order 13423 - Strengthening Federal Environmental, Energy and Transportation Management

40 CFR Part 247, Comprehensive Guideline for Procurement of Products Containing Recovered Materials, May 1, 1996.

C.3.6.8 Solid/Hazardous Waste

Material that results in solid/hazardous wastes (wastes that are non-pumpable or which do not flow by gravity) either continuously or intermittently, including scheduled or routine maintenance work, in addition to normal operation must be

Created on 05/08//2008 - 3 -

ATTACHMENT C– 75.00 (4.4.6) 2.1

designed to allow for removal of the waste in an ergonomic manner and to allow the operator to transfer the waste into a 55 gallon drum – 1A1, 1A2, or other appropriate container, as needed.

Information shall be provided as to the specific quantity, nature and characteristics of the waste generated so that a waste determination may be performed by OEHS/EHSB in accordance with 40 CFR 261 – Identification and Listing of Hazardous Waste.

C.3.6.9 Polychlorinated Biphenyls

The materials shall comply with the regulations set forth with the requirements in 40 CFR 761.30 and shall not contain polychlorinated biphenyls (PCBs) in excess of 2 ppm as required in Title 21, DCMR, Section 1501.4.

C.3.6.10 Identification and Listing of Hazardous Waste

The materials shall not contain contaminants in excess of those listed in Table I, 40 CFR Part 261.24, for the Toxicity Characteristic Leaching Procedure (TCLP).

C.3.6.11 Pre-manufacture Notification

The contractor shall comply with the regulations set forth in 40 CFR Part 720 Pre-manufacture Notification. All suppliers, foreign and domestic, shall certify that the pre-manufacture notification requirements are met for ingredients used in manufacturing the product.

C.3.6.12 Proposition 65

No substance listed by California's "Safe Drinking Water and Toxic Enforcement Act of 1986" (Proposition 65) shall be used as an ingredient in the manufacture of the product. If any listed substance is present as a trace, (ie., not an ingredient) the contractor shall provide a list of such substances with their respective amounts (concentrations).

If the material contains any chemicals recognized by the United States Environmental Protection Agency, Occupational Safety and Health Administration, and/or any of the individual States, as known to cause cancer or known to be a reproductive toxicant, the supplier shall provide a list of the chemical (ie. ingredients or natural contaminant.) The applicable citation shall be noted.

Created on 05/08//2008 - 4 -

ATTACHMENT C– 75.00 (4.4.6) 2.1

Created on 05/08//2008 - 5 -

C.3.6.13 Superfund Amendments Reauthorization Act (SARA)

The contractor shall provide a list of the chemicals and their quantities in the materials which are reportable under the Superfund Amendments Reauthorization Act (SARA) Title III of 1986.

C.3.6.14 Total Toxic Organics

The material shall not contain, as an ingredient, any of the total toxic organic chemicals listed in Title 21 DCMR, Chapter 15, Section1501.4.

C.3.6.15 Recycled Materials

The BEP recommends the use of the highest percentage of Post-consumer recovered material practicable in the manufacture of the finished material. Fifty percent of the fiber used in the paper should originate from waste paper. The Environmental Protection Agency (EPA) defines Post-consumer recovered paper in 40 CFR 247.3.

Rev. # Purpose of Revision Eff. Date

EHSMaterialsSpecificationAttachmentC