BASIC - CDRL- DD1423Pkg_2025-Apr-09-1259.pdf

C24-04-12 APG 66/68 Radar Follow-on

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

TDP TM OTHER MGMT

D. SYSTEM/ITEM E. CONTRACT/PR NO. F. CONTRACTOR

NORTHROP GRUMMAN

1. DATA ITEM NO.

A001

2. TITLE OF DATA ITEM

CONTRACTOR’S PROGRESS AND STATUS REPORT

3. SUBTITLE

Program Management Test

4. AUTHORITY (Data Acquisition Document No.)

DI-MGMT-81928/T

5. CONTRACT REFERENCE

PWS Para. 3.9.1

6. REQUIRING OFFICE

AFLCMC/WAM

7. DD 250 REQ

DD

9. DIST STATEMENT

REQUIRED

D

10. FREQUENCY

BLK16

12. DATE OF FIRST SUBMISSION

BLK 16

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

8. APP CODE

A

11. AS OF DATE

BLK 16

13. DATE OF SUBSEQUENT

SUBMISSION

BLK 16

Draft

Final

Reg Repro

16. REMARKS

NOTE: Changes to office symbol and /or e-mail addresses, when necessary, shall be made by letter through the CO/ACO without further revision to this CDRL.

ALL DELIVERIES SHALL BE SUBMITTED IN ENGLISH.

1. Block 4: Contractor's Electronic Format in Microsoft Office Product is acceptable; paper copy is not required.

2. Block 9: Distribution Statement D. Distribution authorized to the Department of Defense and U.S. DoD contractors only CTI and Export Control (May 2024) Other requests for this document must be referred to AFLCMC/WAM, Hill AFB, Utah.

Export Control Warning: All technical documents that are determined to contain export-controlled technical data shall be marked with the following:

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Section 2751 of Title 22, United States Code) or the Export Control Reform Act of 2018 (Chapter 58 Sections 4801-4852 of Title 50, United States Code). Violations of these export laws are subject to severe criminal penalties.

Disseminate in accordance with provisions of DoD Directive 5230.25 and DoD Instruction 2040.02.

When it is technically impractical to use the entire statement, an abbreviated marking may be used and a copy of the full statement added to the notice to accompany the release of export-controlled technical information required by Part 250 of Title 32, CFR.

Destruction Notice: For classified documents follow the procedures in DoD 5220.22-M, Industrial Security Manual, Section 11-19 or DoD 5200.1-R, Information Security Program Regulation, Chapter IX. For unclassified, limited documents, destroy by any method that will prevent disclosure of contents of reconstruction of the document.

Controlled by: USAF/AFLCMC Controlled by AFLCMC/WAM CUI Category: CTI/EXPTR Distribution Statement: D POC: F-16 SPO Configuration Management, AFLCMC.WWMEJ.F16CM@us.af.mil

For controlled unclassified information (CUI) or controlled technical information (CTI), destroy by any method that will prevent disclosure of contents of reconstruction of the document in accordance with DoDI 5200.48.

BLK16

AFLCMC/WAMI 1

AFLCMC/WAM 1

6089 WARDLEIGH

RD

Bldg 1201

Hill AFB, UT

84056

15. TOTAL 0 2 0

G. PREPARED BY

FLORISBELLO.NICOLE.LYNN.1274745289

H. DATE

2024/05/07

I. APPROVED BY J. DATE

18. ESTIMATED

TOTAL PRICE

DD FORM 1423-1, FEB 2001 PREVIOUS EDITION MAY BE USED Page 1 of 2 Pages

17. PRICE GROUP

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

TDP TM OTHER MGMT

D. SYSTEM/ITEM E. CONTRACT/PR NO.

F. CONTRACTOR

NORTHROP GRUMMAN

16. REMARKS (Continued)

3. Blocks 10, 11, 12, 13: The first submittal shall be NLT thirty (30) calendar days after contract award.

Subsequent submittals shall be monthly thereafter throughout the life of the contract.

4. Block 14: Contractor Shall submit deliverable(s) to the following email addresses:

a. AFLCMC.WWM.F-16DataMgmt@us.af.mil

DD FORM 1423-1, FEB 2001 Page 2 of 2 Pages

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

TDP TM OTHER MGMT

D. SYSTEM/ITEM E. CONTRACT/PR NO. F. CONTRACTOR

NORTHROP GRUMMAN

1. DATA ITEM NO.

A002

2. TITLE OF DATA ITEM

Technical Report - Study/Services

3. SUBTITLE

Cost Reporting Status

4. AUTHORITY (Data Acquisition Document No.)

DI-MISC-80508B/T

5. CONTRACT REFERENCE

PWS Para. 2.2, 3.9.1

6. REQUIRING OFFICE

AFLCMC/WAM

7. DD 250 REQ

DD

9. DIST STATEMENT

REQUIRED

D

10. FREQUENCY

BLK16

12. DATE OF FIRST SUBMISSION

BLK 16

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

8. APP CODE

A

11. AS OF DATE

BLK 16

13. DATE OF SUBSEQUENT

SUBMISSION

BLK 16

Draft

Final

Reg Repro

16. REMARKS

NOTE: Changes to office symbol and /or e-mail addresses, when necessary, shall be made by letter through the CO/ACO without further revision to this CDRL.

ALL DELIVERIES SHALL BE SUBMITTED IN ENGLISH.

1. Block 4: Contractor's Electronic Format in Microsoft Office Product is acceptable; paper copy is not required.

2. Block 9: Distribution Statement D. Distribution authorized to the Department of Defense and U.S. DoD contractors only CTI and Export Control (May 2024) Other requests for this document must be referred to AFLCMC/WAM, Hill AFB, Utah.

Export Control Warning: All technical documents that are determined to contain export-controlled technical data shall be marked with the following:

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Section 2751 of Title 22, United States Code) or the Export Control Reform Act of 2018 (Chapter 58 Sections 4801-4852 of Title 50, United States Code). Violations of these export laws are subject to severe criminal penalties.

Disseminate in accordance with provisions of DoD Directive 5230.25 and DoD Instruction 2040.02.

When it is technically impractical to use the entire statement, an abbreviated marking may be used and a copy of the full statement added to the notice to accompany the release of export-controlled technical information required by Part 250 of Title 32, CFR.

Destruction Notice: For classified documents follow the procedures in DoD 5220.22-M, Industrial Security Manual, Section 11-19 or DoD 5200.1-R, Information Security Program Regulation, Chapter IX. For unclassified, limited documents, destroy by any method that will prevent disclosure of contents of reconstruction of the document.

Controlled by: USAF/AFLCMC Controlled by AFLCMC/WAM CUI Category: CTI/EXPTR Distribution Statement: D POC: F-16 SPO Configuration Management, AFLCMC.WWMEJ.F16CM@us.af.mil

For controlled unclassified information (CUI) or controlled technical information (CTI), destroy by any method that will prevent disclosure of contents of reconstruction of the document in accordance with DoDI 5200.48.

BLK16

AFLCMC/WAMI 1

AFLCMC/WAM 1

6089 WARDLEIGH

Road

BLDG 1201

Hill AFB, UT

84056

15. TOTAL 0 2 0

G. PREPARED BY

FLORISBELLO.NICOLE.LYNN.1274745289

H. DATE

2024/05/07

I. APPROVED BY J. DATE

18. ESTIMATED

TOTAL PRICE

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

16. REMARKS (Continued)

3. Blocks 10, 11, 12, 13: The contractor shall submit report NLT the due date provided on specific PWS deliverable. The Government will be allowed 10 business days to review and return comments. The Contractor shall submit the updated report incorporating Government comments NLT 10 business days following receipt of Government comments.

4. Block 14: Contractor Shall submit deliverable(s) to the following email addresses:

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

TDP TM OTHER MGMT

D. SYSTEM/ITEM E. CONTRACT/PR NO. F. CONTRACTOR

NORTHROP GRUMMAN

1. DATA ITEM NO.

A003

2. TITLE OF DATA ITEM

Technical Report - Study/Services

3. SUBTITLE

Requirement Analysis

4. AUTHORITY (Data Acquisition Document No.)

DI-MISC-80508B/T

5. CONTRACT REFERENCE

PWS Para. 4.2.1

6. REQUIRING OFFICE

AFLCMC/WAM

7. DD 250 REQ

DD

9. DIST STATEMENT

REQUIRED

D

10. FREQUENCY

BLK16

12. DATE OF FIRST SUBMISSION

BLK 16

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

8. APP CODE

A

11. AS OF DATE

BLK 16

13. DATE OF SUBSEQUENT

SUBMISSION

BLK 16

Draft

Final

Reg Repro

16. REMARKS

NOTE: Changes to office symbol and /or e-mail addresses, when necessary, shall be made by letter through the CO/ACO without further revision to this CDRL.

ALL DELIVERIES SHALL BE SUBMITTED IN ENGLISH.

1. Block 4: Contractor's Electronic Format in Microsoft Office Product is acceptable; paper copy is not required.

2. Block 9: Distribution Statement D. Distribution authorized to the Department of Defense and U.S. DoD contractors only CTI and Export Control (May 2024) Other requests for this document must be referred to AFLCMC/WAM, Hill AFB, Utah.

Export Control Warning: All technical documents that are determined to contain export-controlled technical data shall be marked with the following:

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Section 2751 of Title 22, United States Code) or the Export Control Reform Act of 2018 (Chapter 58 Sections 4801-4852 of Title 50, United States Code). Violations of these export laws are subject to severe criminal penalties.

Disseminate in accordance with provisions of DoD Directive 5230.25 and DoD Instruction 2040.02.

When it is technically impractical to use the entire statement, an abbreviated marking may be used and a copy of the full statement added to the notice to accompany the release of export-controlled technical information required by Part 250 of Title 32, CFR.

Destruction Notice: For classified documents follow the procedures in DoD 5220.22-M, Industrial Security Manual, Section 11-19 or DoD 5200.1-R, Information Security Program Regulation, Chapter IX. For unclassified, limited documents, destroy by any method that will prevent disclosure of contents of reconstruction of the document.

Controlled by: USAF/AFLCMC Controlled by AFLCMC/WAM CUI Category: CTI/EXPTR Distribution Statement: D POC: F-16 SPO Configuration Management, AFLCMC.WWMEJ.F16CM@us.af.mil

For controlled unclassified information (CUI) or controlled technical information (CTI), destroy by any method that will prevent disclosure of contents of reconstruction of the document in accordance with DoDI 5200.48.

BLK16

AFLCMC/WAMI 1

AFLCMC/WAM 1

6089 WARDLEIGH

ROAD

BLDG 1201

Hill AFB, UT

84056

15. TOTAL 0 2 0

G. PREPARED BY

FLORISBELLO.NICOLE.LYNN.1274745289

H. DATE

2024/05/07

I. APPROVED BY J. DATE

18. ESTIMATED

TOTAL PRICE

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

16. REMARKS (Continued)

3. Blocks 10, 11, 12, 13: The contractor shall submit report NLT the due date provided on specific PWS deliverable. The Government will be allowed 10 business days to review and return comments. The Contractor shall submit the updated report incorporating Government comments NLT 10 business days following receipt of Government comments.

4. Block 14: Contractor Shall submit deliverable(s) to the following email addresses:

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

TDP TM OTHER MGMT

D. SYSTEM/ITEM E. CONTRACT/PR NO. F. CONTRACTOR

NORTHROP GRUMMAN

1. DATA ITEM NO.

A004

2. TITLE OF DATA ITEM

Technical Report - Study/Services

3. SUBTITLE

Engineering Technical Support

4. AUTHORITY (Data Acquisition Document No.)

DI-MISC-80508B/T

5. CONTRACT REFERENCE

PWS Para. 3.1, 4.2, 5.1

6. REQUIRING OFFICE

AFLCMC/WAM

7. DD 250 REQ

DD

9. DIST STATEMENT

REQUIRED

D

10. FREQUENCY

BLK16

12. DATE OF FIRST SUBMISSION

BLK 16

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

8. APP CODE

A

11. AS OF DATE

BLK 16

13. DATE OF SUBSEQUENT

SUBMISSION

BLK 16

Draft

Final

Reg Repro

16. REMARKS

NOTE: Changes to office symbol and /or e-mail addresses, when necessary, shall be made by letter through the CO/ACO without further revision to this CDRL.

ALL DELIVERIES SHALL BE SUBMITTED IN ENGLISH.

1. Block 4: Contractor's Electronic Format in Microsoft Office Product is acceptable; paper copy is not required.

2. Block 9: Distribution Statement D. Distribution authorized to the Department of Defense and U.S. DoD contractors only CTI and Export Control (May 2024) Other requests for this document must be referred to AFLCMC/WAM, Hill AFB, Utah.

Export Control Warning: All technical documents that are determined to contain export-controlled technical data shall be marked with the following:

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Section 2751 of Title 22, United States Code) or the Export Control Reform Act of 2018 (Chapter 58 Sections 4801-4852 of Title 50, United States Code). Violations of these export laws are subject to severe criminal penalties.

Disseminate in accordance with provisions of DoD Directive 5230.25 and DoD Instruction 2040.02.

When it is technically impractical to use the entire statement, an abbreviated marking may be used and a copy of the full statement added to the notice to accompany the release of export-controlled technical information required by Part 250 of Title 32, CFR.

Destruction Notice: For classified documents follow the procedures in DoD 5220.22-M, Industrial Security Manual, Section 11-19 or DoD 5200.1-R, Information Security Program Regulation, Chapter IX. For unclassified, limited documents, destroy by any method that will prevent disclosure of contents of reconstruction of the document.

Controlled by: USAF/AFLCMC Controlled by AFLCMC/WAM CUI Category: CTI/EXPTR Distribution Statement: D POC: F-16 SPO Configuration Management, AFLCMC.WWMEJ.F16CM@us.af.mil

For controlled unclassified information (CUI) or controlled technical information (CTI), destroy by any method that will prevent disclosure of contents of reconstruction of the document in accordance with DoDI 5200.48.

BLK16

AFLCMC/WAMI 1

AFLCMC/WAM 1

6089 WARDLEIGH

ROAD

BLDG 1201

Hill AFB, UT

84056

15. TOTAL 0 2 0

G. PREPARED BY

FLORISBELLO.NICOLE.LYNN.1274745289

H. DATE

2024/05/07

I. APPROVED BY J. DATE

18. ESTIMATED

TOTAL PRICE

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

16. REMARKS (Continued)

3. Blocks 10, 11, 12, 13: The contractor shall submit report NLT thirty (30) calendar days after award of each Delivery Order. Subsequent submittals shall be monthly thereafter throughout the life of the contract.

The Government will be allowed 10 business days to review and return comments. The Contractor shall submit the updated report incorporating Government comments NLT 10 business days following receipt of Government comments.

4. Block 14: Contractor Shall submit deliverable(s) to the following email addresses:

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

TDP TM OTHER MGMT

D. SYSTEM/ITEM E. CONTRACT/PR NO. F. CONTRACTOR

NORTHROP GRUMMAN

1. DATA ITEM NO.

A005

2. TITLE OF DATA ITEM

Test/Inspection Report

3. SUBTITLE

Test/Inspection Report DTO

4. AUTHORITY (Data Acquisition Document No.)

DI-NDTI-80809B/T

5. CONTRACT REFERENCE

PWS Para. 4.2.2

6. REQUIRING OFFICE

AFLCMC/WAM

7. DD 250 REQ

DD

9. DIST STATEMENT

REQUIRED

D

10. FREQUENCY

BLK16

12. DATE OF FIRST SUBMISSION

BLK 16

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

8. APP CODE

A

11. AS OF DATE

BLK 16

13. DATE OF SUBSEQUENT

SUBMISSION

BLK 16

Draft

Final

Reg Repro

16. REMARKS

NOTE: Changes to office symbol and /or e-mail addresses, when necessary, shall be made by letter through the CO/ACO without further revision to this CDRL.

ALL DELIVERIES SHALL BE SUBMITTED IN ENGLISH.

1. Block 4: Contractor's Electronic Format in Microsoft Office Product is acceptable; paper copy is not required.

2. Block 9: Distribution Statement D. Distribution authorized to the Department of Defense and U.S. DoD contractors only CTI and Export Control (May 2024) Other requests for this document must be referred to AFLCMC/WAM, Hill AFB, Utah.

Export Control Warning: All technical documents that are determined to contain export-controlled technical data shall be marked with the following:

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Section 2751 of Title 22, United States Code) or the Export Control Reform Act of 2018 (Chapter 58 Sections 4801-4852 of Title 50, United States Code). Violations of these export laws are subject to severe criminal penalties.

Disseminate in accordance with provisions of DoD Directive 5230.25 and DoD Instruction 2040.02.

When it is technically impractical to use the entire statement, an abbreviated marking may be used and a copy of the full statement added to the notice to accompany the release of export-controlled technical information required by Part 250 of Title 32, CFR.

Destruction Notice: For classified documents follow the procedures in DoD 5220.22-M, Industrial Security Manual, Section 11-19 or DoD 5200.1-R, Information Security Program Regulation, Chapter IX. For unclassified, limited documents, destroy by any method that will prevent disclosure of contents of reconstruction of the document.

Controlled by: USAF/AFLCMC Controlled by AFLCMC/WAM CUI Category: CTI/EXPTR Distribution Statement: D POC: F-16 SPO Configuration Management, AFLCMC.WWMEJ.F16CM@us.af.mil

For controlled unclassified information (CUI) or controlled technical information (CTI), destroy by any method that will prevent disclosure of contents of reconstruction of the document in accordance with DoDI 5200.48.

BLK16

AFLCMC/WAMI 1

AFLCMC/WAM 1

6089 WARDLEIGH

ROAD

BLDG 1201

Hill AFB, UT

84056

15. TOTAL 0 2 0

G. PREPARED BY

FLORISBELLO.NICOLE.LYNN.1274745289

H. DATE

2024/05/07

I. APPROVED BY J. DATE

18. ESTIMATED

TOTAL PRICE

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

16. REMARKS (Continued)

3. Blocks 10, 11, 12, 13: The contractor shall submit report NLT the due date provided on specific PWS deliverable. The Government will be allowed 10 business days to review and return comments. The Contractor shall submit the updated report incorporating Government comments NLT 10 business days following receipt of Government comments.

4. Block 14: Contractor Shall submit deliverable(s) to the following email addresses:

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

TDP TM OTHER MGMT

D. SYSTEM/ITEM E. CONTRACT/PR NO. F. CONTRACTOR

NORTHROP GRUMMAN

1. DATA ITEM NO.

A006

2. TITLE OF DATA ITEM

Technical Report - Study/Services

3. SUBTITLE

Field Reliability and Supportability

4. AUTHORITY (Data Acquisition Document No.)

DI-MISC 80508B/T

5. CONTRACT REFERENCE

PWS Para. 3.7.5, 3.8.2, 4.3

6. REQUIRING OFFICE

AFLCMC/WAM

7. DD 250 REQ

DD

9. DIST STATEMENT

REQUIRED

D

10. FREQUENCY

BLK16

12. DATE OF FIRST SUBMISSION

BLK 16

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

8. APP CODE

A

11. AS OF DATE

BLK 16

13. DATE OF SUBSEQUENT

SUBMISSION

BLK 16

Draft

Final

Reg Repro

16. REMARKS

NOTE: Changes to office symbol and /or e-mail addresses, when necessary, shall be made by letter through the CO/ACO without further revision to this CDRL.

ALL DELIVERIES SHALL BE SUBMITTED IN ENGLISH.

1. Block 4: Contractor's Electronic Format in Microsoft Office Product is acceptable; paper copy is not required.

2. Block 9: Distribution Statement D. Distribution authorized to the Department of Defense and U.S. DoD contractors only CTI and Export Control (May 2024) Other requests for this document must be referred to AFLCMC/WAM, Hill AFB, Utah.

Export Control Warning: All technical documents that are determined to contain export-controlled technical data shall be marked with the following:

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Section 2751 of Title 22, United States Code) or the Export Control Reform Act of 2018 (Chapter 58 Sections 4801-4852 of Title 50, United States Code). Violations of these export laws are subject to severe criminal penalties.

Disseminate in accordance with provisions of DoD Directive 5230.25 and DoD Instruction 2040.02.

When it is technically impractical to use the entire statement, an abbreviated marking may be used and a copy of the full statement added to the notice to accompany the release of export-controlled technical information required by Part 250 of Title 32, CFR.

Destruction Notice: For classified documents follow the procedures in DoD 5220.22-M, Industrial Security Manual, Section 11-19 or DoD 5200.1-R, Information Security Program Regulation, Chapter IX. For unclassified, limited documents, destroy by any method that will prevent disclosure of contents of reconstruction of the document.

Controlled by: USAF/AFLCMC Controlled by AFLCMC/WAM CUI Category: CTI/EXPTR Distribution Statement: D POC: F-16 SPO Configuration Management, AFLCMC.WWMEJ.F16CM@us.af.mil

For controlled unclassified information (CUI) or controlled technical information (CTI), destroy by any method that will prevent disclosure of contents of reconstruction of the document in accordance with DoDI 5200.48.

BLK16

AFLCMC/WAMI 1

AFLCMC/WAM 1

6089 WARDLEIGH

ROAD

BLDG 1201

Hill AFB, UT

84056

15. TOTAL 0 2 0

G. PREPARED BY

FLORISBELLO.NICOLE.LYNN.1274745289

H. DATE

2024/05/07

I. APPROVED BY J. DATE

18. ESTIMATED

TOTAL PRICE

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

16. REMARKS (Continued)

3. Blocks 10, 11, 12, 13: The contractor shall submit I.E, M.E, T.E, and Field Reliability and Supportability reports semi-annually six (6) months after contract award until the end of the contract.

The contractor shall submit Spares Provisioning reports as requested and specified on specific PWS delivery order.

4. Block 14: Contractor Shall submit deliverable(s) to the following email addresses:

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

TDP TM OTHER MGMT

D. SYSTEM/ITEM E. CONTRACT/PR NO. F. CONTRACTOR

NORTHROP GRUMMAN

1. DATA ITEM NO.

A007

2. TITLE OF DATA ITEM

Test/Inspection Report

3. SUBTITLE

Test Inspection STS Updates

4. AUTHORITY (Data Acquisition Document No.)

DI-NDTI-80809B/T

5. CONTRACT REFERENCE

PWS Para. 3.7.3, 4.4

6. REQUIRING OFFICE

AFLCMC/WAM

7. DD 250 REQ

LT

9. DIST STATEMENT

REQUIRED

D

10. FREQUENCY

BLK16

12. DATE OF FIRST SUBMISSION

BLK 16

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

8. APP CODE

A

11. AS OF DATE

BLK 16

13. DATE OF SUBSEQUENT

SUBMISSION

BLK 16

Draft

Final

Reg Repro

16. REMARKS

NOTE: Changes to office symbol and /or e-mail addresses, when necessary, shall be made by letter through the CO/ACO without further revision to this CDRL.

ALL DELIVERIES SHALL BE SUBMITTED IN ENGLISH.

1. Block 4: Contractor's Electronic Format in Microsoft Office Product is acceptable; paper copy is not required.

2. Block 9: Distribution Statement D. Distribution authorized to the Department of Defense and U.S. DoD contractors only CTI and Export Control (May 2024) Other requests for this document must be referred to AFLCMC/WAM, Hill AFB, Utah.

Export Control Warning: All technical documents that are determined to contain export-controlled technical data shall be marked with the following:

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Section 2751 of Title 22, United States Code) or the Export Control Reform Act of 2018 (Chapter 58 Sections 4801-4852 of Title 50, United States Code). Violations of these export laws are subject to severe criminal penalties.

Disseminate in accordance with provisions of DoD Directive 5230.25 and DoD Instruction 2040.02.

When it is technically impractical to use the entire statement, an abbreviated marking may be used and a copy of the full statement added to the notice to accompany the release of export-controlled technical information required by Part 250 of Title 32, CFR.

Destruction Notice: For classified documents follow the procedures in DoD 5220.22-M, Industrial Security Manual, Section 11-19 or DoD 5200.1-R, Information Security Program Regulation, Chapter IX. For unclassified, limited documents, destroy by any method that will prevent disclosure of contents of reconstruction of the document.

Controlled by: USAF/AFLCMC Controlled by AFLCMC/WAM CUI Category: CTI/EXPTR Distribution Statement: D POC: F-16 SPO Configuration Management, AFLCMC.WWMEJ.F16CM@us.af.mil

For controlled unclassified information (CUI) or controlled technical information (CTI), destroy by any method that will prevent disclosure of contents of reconstruction of the document in accordance with DoDI 5200.48.

BLK16

AFLCMC/WAMI 1

AFLCMC/WAM 1

6089 WARDLEIGH

ROAD

BLDG 1201

Hill AFB, UT

84056

15. TOTAL 0 2 0

G. PREPARED BY

FLORISBELLO.NICOLE.LYNN.1274745289

H. DATE

2024/05/07

I. APPROVED BY J. DATE

18. ESTIMATED

TOTAL PRICE

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

16. REMARKS (Continued)

3. Blocks 10, 11, 12, 13: The contractor shall submit reports semi-annually six (6) months after contract award until the end of the contract. The Government will be allowed 10 business days to review and return comments. The Contractor shall submit the updated report incorporating Government comments NLT 10 business days following receipt of Government comments.

4. Block 14: Contractor Shall submit deliverable(s) to the following email addresses:

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

TDP TM OTHER MGMT

D. SYSTEM/ITEM E. CONTRACT/PR NO. F. CONTRACTOR

NORTHROP GRUMMAN

1. DATA ITEM NO.

A008

2. TITLE OF DATA ITEM

Contractor's Progress and Status Report

3. SUBTITLE

Vendor Data Base

4. AUTHORITY (Data Acquisition Document No.)

DI-NDTI-80809B/T

5. CONTRACT REFERENCE

PWS Para. 3.8.1

6. REQUIRING OFFICE

AFLCMC/WAM

7. DD 250 REQ

LT

9. DIST STATEMENT

REQUIRED

B

10. FREQUENCY

BLK16

12. DATE OF FIRST SUBMISSION

BLK 16

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

8. APP CODE

11. AS OF DATE

BLK 16

13. DATE OF SUBSEQUENT

SUBMISSION

BLK 16

Draft

Final

Reg Repro

16. REMARKS

NOTE: Changes to office symbol and /or e-mail addresses, when necessary, shall be made by letter through the CO/ACO without further revision to this CDRL.

ALL DELIVERIES SHALL BE SUBMITTED IN ENGLISH.

1. Block 4: Contractor's Electronic Format in Microsoft Office Product is acceptable; paper copy is not required.

2. Block 9: Distribution Statement D. Distribution authorized to the Department of Defense and U.S. DoD contractors only CTI and Export Control (May 2024) Other requests for this document must be referred to AFLCMC/WAM, Hill AFB, Utah.

Export Control Warning: All technical documents that are determined to contain export-controlled technical data shall be marked with the following:

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Section 2751 of Title 22, United States Code) or the Export Control Reform Act of 2018 (Chapter 58 Sections 4801-4852 of Title 50, United States Code). Violations of these export laws are subject to severe criminal penalties.

Disseminate in accordance with provisions of DoD Directive 5230.25 and DoD Instruction 2040.02.

When it is technically impractical to use the entire statement, an abbreviated marking may be used and a copy of the full statement added to the notice to accompany the release of export-controlled technical information required by Part 250 of Title 32, CFR.

Destruction Notice: For classified documents follow the procedures in DoD 5220.22-M, Industrial Security Manual, Section 11-19 or DoD 5200.1-R, Information Security Program Regulation, Chapter IX. For unclassified, limited documents, destroy by any method that will prevent disclosure of contents of reconstruction of the document.

Controlled by: USAF/AFLCMC Controlled by AFLCMC/WAM CUI Category: CTI/EXPTR Distribution Statement: B POC: F-16 SPO Configuration Management, AFLCMC.WWMEJ.F16CM@us.af.mil

For controlled unclassified information (CUI) or controlled technical information (CTI), destroy by any method that will prevent disclosure of contents of reconstruction of the document in accordance with DoDI 5200.48.

3. Blocks 10, 11, 12, 13:

BLK16

AFLCMC/WAMI 1

AFLCMC/WAM 1

6089 WARDLEIGH

ROAD

BLDG 1201

Hill AFB, UT

84056

15. TOTAL 0 2 0

G. PREPARED BY

FLORISBELLO.NICOLE.LYNN.1274745289

H. DATE

2024/05/07

I. APPROVED BY J. DATE

18. ESTIMATED

TOTAL PRICE

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

16. REMARKS (Continued)

a. DMS Report(s) shall be submitted quarterly NLT ninety (90) calendar days after contract award and shall be in portable document format (PDF).

b. Industrial Base Report shall be submitted semi annually (6) months after contract award and shall be in portable document format (PDF).

c. The Government will be allowed 10 business days to review and return comments. The Contractor shall submit the updated report incorporating Government comments NLT 10 business days following receipt of Government comments.

4. Block 14: Contractor Shall submit deliverable(s) to the following email addresses:

a. AFLCMC.WWM.F-16DataMgmt@us.af.mil

b. Northrup Grumman (NGC) secure site (NGC Safe)

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

TDP TM OTHER MGMT

D. SYSTEM/ITEM E. CONTRACT/PR NO.

FA8251-20

F. CONTRACTOR

NORTHROP GRUMMAN

1. DATA ITEM NO.

A009

2. TITLE OF DATA ITEM

Product Engineering Design Data and Associated Lists

3. SUBTITLE

4. AUTHORITY (Data Acquisition Document No.)

DI-SESS-81000F/T

5. CONTRACT REFERENCE

Sow

6. REQUIRING OFFICE

AFLCMC/WAMI

7. DD 250 REQ

DD

9. DIST STATEMENT

REQUIRED

D

10. FREQUENCY

BLK16

12. DATE OF FIRST SUBMISSION

BLK 16

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

8. APP CODE

11. AS OF DATE

BLK 16

13. DATE OF SUBSEQUENT

SUBMISSION

BLK 16

Draft

Final

Reg Repro

16. REMARKS

A. Changes to all office symbols and/or e-mail addresses, when necessary shall be made by letter through the government CO/ACO without further revision to this CDRL.

1. Block 4:

a. Block 10, change DOD-STD-100 to MIL-STD-100C (as guidance).

b. The contractor shall document the configuration of all non-production, sustained configurations. Applies to prime contractor, vendors and subcontractors.

c. Complete set of engineering data to define AN/APG 66/68 RADAR requirements is required which includes assembly drawings (down to and including SRU drawings). When applicable: Acceptance Test Procedures are also required. Data call outs below the detail drawing of referenced document level on parts lists are not required, Software and Firmware are not required by this CDRL.

d. Engineering Data Changes: All Class I and Class II changes as defined in DOD-STD-480(as guidance only) shall be incorporated on the application engineering drawings and associated lists.

e. On engineering drawings and associated lists, maintain records of all configurations delivered so that the details of any configuration delivered may be determined without research of or recourse to change history.

f. Replace paragraph 201.1.2, Note 5, of DOD-STD-100C(as guidance only) with the following: "Specification control drawings shall not be used to depict commercial or vendor developed items upon which a design activity has placed additional physical or functional requirements in addition to those normally provided by vendors. These kinds of items shall be depicted on either selected item drawings or alter item drawings are appropriate. Additional qualification test requirements shall be regarded as an additional physical or functional requirement".

g. Data deliveries shall be limited to applicable data not previously delivered to Hill Air Force Base.

h. Identify the contract number(s), CAGE, drawing number, latest revision, and date the drawing was delivered to Hill Air Force Base.

i. All documents, Engineering Drawings, Associated Lists referenced there in shall be in the English language and 3rd angle projection shall be used.

j. The contractor shall use DOD-STD-100C and MIL-STD-130 (as guidance only) in assignment and identification of parts numbers and drawing numbers. Drawings shall specify requirements for markings of MIL-STD-130. The drawings shall identify the metthod of marking and location on the part.

k. Tube bending drawings shall be prepared using specification MIL-D-9898 (as guidance only).

l. The proprietary FAR clause shall not appear on the drawing that does not disclose proprietary information.

AFLCMC/WAMI 1

6089 Wardleigh

ROAD

building 1201

Hill AFB, UT

84056

AFLCMC/LZPEM 1

6032 Fir Ave

Building 1237

HAFB, UT

84056

15. TOTAL 0 2 0

G. PREPARED BY

FLORISBELLO.NICOLE.LYNN.1274745289

H. DATE

2024/05/07

I. APPROVED BY J. DATE

18. ESTIMATED

TOTAL PRICE

DD FORM 1423-1, FEB 2001 PREVIOUS EDITION MAY BE USED Page 1 of 3 Pages

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

TDP TM OTHER MGMT

D. SYSTEM/ITEM E. CONTRACT/PR NO.

FA8251-20

F. CONTRACTOR

NORTHROP GRUMMAN

16. REMARKS (Continued)

m. Procurement requirements IAW MIL-STD-31000 and using DOD-D-1000B(as guidance only) with tailored paragraph 6.2 as follows:

1. Drawing, Engineering data and Associated Lists, 28 Oct 77(as guidance).

2. Level 3, tailored by Block 16, paragraph 1 c.

3. Use contractor Design Activity Identifiers.

4. N/A

5. N/A

6. See Block 4.

7. Metric System N/A.

8. See CDRL.

9. As applicable. Company standards are acceptable per 3.7.

10. Parts Lists are required.

11. Parts List is required for each assembly drawing.

12. Mono-detail drawings are required. However, multi-detailed drawings are acceptable, but limited to the depiction of like items, detail assemblies, parts detailed and assembled on the same drawing sheet.

13. Not different than Paragraph 3.4.3.

14. As applicable, control drawings shall conform to paragraph 3.5.2.

15. Parts list may be integral or separate. However, when separate, a different list shall be prepared for each assembly and subassembly drawing.

16. Drifting medium DOD-STD-100C, paragraph 104 as guidance.

17. see Block 14.

18. see CDRL, para 3 d.

19. see Block 14.

2. Block 7 and 8: Form DD250 will be signed by government addressee listed in BLK 14 of this CDRL after final delivery of data has been approved by the Government Engineer and Engineering Data Management Officer (EDMO). Government will respond with approval/disapproval within (30) calendar days after receipt.

3. Block 9: Distribution Statement, Export Control Warning and Destruction Notice shall be IAW DoD Instruction 5230.24.

DISTRIBUTION STATEMENT D: Distribution authorized to Department of Defense and U.S. DoD contractors only;

critical technology, export controlled; 01 May 2024. Other requests for this document shall be referred to AFLCMC/WAM, Hill AFB, UT 84056.

WARNING: This document contains technical data whose export is restricted by the Arms Export Control Act (Section 2751 of Title 22, United States Code) or the Export Control Reform Act of 2018 (Chapter 58 Sections 4801-4852 of Title 50, United States Code). Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DoD Directive 5230.25 and DoD Instruction 2040.02.

DESTRUCTION NOTICE: Comply with distribution statement and destroy by any method that will prevent disclosure of contents or reconstruction of the document.

CONTROLLED UNCLASSIFIED INFORMATION (CUI):

“CUI/" shall be displayed at the top and bottom of each (all) sheets:

The following CUI information shall be placed on the first sheet of each document, Product Engineering Design Data and Associated Lists IAW DoDI 5200.48:

Controlled by: USAF/AFLCMC Controlled by AFLCMC/WAM CUI Category: CTI/EXPT CTRL Distribution/Dissemination Control: Distribution Statement D POC: AFLCMC.WWM.F-16DataMgmt@us.af.mil

NOTE: These CDRL requirements shall be levied on all relationships of Contractor with Subcontractors/Vendors: The contractor shall levy on sub-contractors and sub-vendors the same requirements for Technical Data Packages (TDPs) as are levied on them by this contract. This requirement shall apply at all tiers of sub-contractor/vendor levels associated with the program.

All data deliveries shall be submitted in English. If English and/or other language is provided, only English language shall be binding/approved.

DD FORM 1423-1, FEB 2001 Page 2 of 3 Pages

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

A. CONTRACT LINE ITEM NO.

A0001

B. EXHIBIT

A

C. CATEGORY:

TDP TM OTHER MGMT

D. SYSTEM/ITEM E. CONTRACT/PR NO.

FA8251-20

F. CONTRACTOR

NORTHROP GRUMMAN

16. REMARKS (Continued)

4. Block 14:

a. The contractor shall submit a DD Form 250 at time of shipment to:

Block 14 Addressee 1.

b. A letter of transmittal for each data submittal shall be sent to the following e-mail addesses:

1. AFLCMC.WWM.F-16DataMgmt@us.af.mil

2. aflcmc.lzpem.edmo@us.af.mil

c. The contractor shall submit a shipping list with each shipment of data delivered. The format shall be contractor format. The list shall specify if the shipment is partial, incremental, update, final or make-up (corrected) as appropriate.

d. Entries for associated lists shall list document type (i.e., PL), drawing number, and parts list revision letter.

e. Vendor shipping list shall be contractor format. Vendor shall be segregated by Cage Code. Vendor shipping list shall contain, as a minimum:

1. Drawing/Document number

2. Revision status

3. Cage Code

f. Delivery of Engineering Drawings and Associated Lists shall be via CD-ROM to the address below or other digital means agreed upon between the government CO/PCO, Program Office and AFLCMC/LZPEM and Northrop Grumman:

AFLCMC/LZPEM

6032 FIR AVE

Building 1218 Hill AFB, UT 84056-8525 Attn: EDMO OFFICE

1. The contractor shall deliver updates to all data annually as drawing changes occur.

2. All submittals (including updates) will be reviewed and approved or disapproved by the government no later than thirty (30) calendar days after receipt.

g. The data shall be delivered in the following formats:

1. All drawings shall be delivered in PDF as 1 composite file for all sheets.

2. Instructions ) for All documents (Technical Data Package) submitted in PDF Format.

Metadata/indexing shall be prepared IAW Digital Data Description Requirement document 9579776 Revision N (CAGE 98752) Option 2 page 21 Hill Air Force Base.

h. Final Delivery of Product Drawings and Associated Lists shall be submitted through CD-ROM (CD-R) to BLK 14 addressees, subject to government final review and acceptance. Updates continue to be delivered annually as drawing changes occur. ALL drawings are subject to government final review and acceptance.

DD FORM 1423-1, FEB 2001 Page 3 of 3 Pages

DD FORM 1423-1, FEB 2001

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

PREVIOUS EDITION MAY BE USED.

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports (0701-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302. Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. Please DO NOT RETURN your form to the above address. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No.

listed in Block E.

A. CONTRACT LINE ITEM NO. B. EXHIBIT C. CATEGORY:

TDP ________ TM _______ OTHER

D. SYSTEM/ITEM E. CONTRACT/PR NO. F. CONTRACTOR

1. DATA ITEM NO. 2. TITLE OF DATA ITEM 3. SUBTITLE

4. AUTHORITY (Data Acquisition Document No.) 5. CONTRACT REFERENCE 6. REQUIRING OFFICE

7. DD 250 REQ

8. APP CODE

9. DIST STATEMENT

REQUIRED

10. FREQUENCY

11. AS OF DATE

12. DATE OF FIRST SUBMISSION

13. DATE OF SUBSEQUENT

SUBMISSION

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

Draft Final

Reg Repro

15. TOTAL

16. REMARKS

17. PRICE GROUP

18. ESTIMATED

TOTAL PRICE

G. PREPARED BY H. DATE I. APPROVED BY J. DATE

Page of Pages

(1 Data Item)

A. CONTRACT LINE ITEM NO. B. EXHIBIT C. CATEGORY:

E. CONTRACT/PR NO. F. CONTRACTOR

16. REMARKS (Continued)

Page of Pages

D. SYSTEM/ITEM

TDP ________ TM _______ OTHER

(1 Data Item)

A. CONTRACT LINE ITEM NO. B. EXHIBIT C. CATEGORY:

E. CONTRACT/PR NO. F. CONTRACTOR

16. REMARKS (Continued)

Page of Pages

D. SYSTEM/ITEM

TDP ________ TM _______ OTHER

INSTRUCTIONS FOR COMPLETING DD FORM 1423

(See DoD 5010.12-M for detailed instructions.)

FOR GOVERNMENT PERSONNEL

Item A. Self-explanatory.

Item B. Self-explanatory.

Item C. Mark (X) appropriate category: TDP - Technical Data Package;

TM - Technical Manual; Other - other category of data, such as "Provisioning,""Configuration Management," etc.

Item D. Enter name of system/item being acquired that data will support.

Item E. Self-explanatory (to be filled in after contract award).

Item F. Self-explanatory (to be filled in after contract award).

Item G. Signature of preparer of CDRL.

Item H. Date CDRL was prepared.

Item I. Signature of CDRL approval authority.

Item J. Date CDRL was approved.

Item 1. See DoD FAR Supplement Subpart 4.71 for proper numbering.

Item 2. Enter title as it appears on data acquisition document cited in Item 4.

Item 3. Enter subtitle of data item for further definition of data item (optional entry).

Item 4. Enter Data Item Description (DID) number, military specification number, or military standard number listed in DoD 5010.12-L (AMSDL), or one-time DID number, that defines data content and format requirements.

Item 5. Enter reference to tasking in contract that generates requirement for the data item (e.g., Statement of Work paragraph number).

Item 6. Enter technical office responsible for ensuring adequacy of the data item.

Item 7. Specify requirement for inspection/acceptance of the data item by the Government.

Item 8. Specify requirement for approval of a draft before preparation of the final data item.

Item 9. For technical data, specify requirement for contractor to mark the appropriate distribution statement on the…