RFP 24-01 MOBILE COMMAND VEHICLE

ATTACHMENT D

Item # Qty Description

1.00

CHASSIS/BODY DIMENSIONS:

22’ walk-in van

• Wheelbase of chassis: 208"

• Overall length of apparatus: 377"

• Overall apparatus width, rub rail to rub rail: 99"

• Overall height of apparatus (loaded): 128"

• Interior walkway height raw body: 83"

• Interior walkway height finished: 81.5"

• Interior walkway length: 264"

• Interior raw body width: 96"

• Interior finished body width: 87"

2.00 CHASSIS:

2.01 1

Forward control gas chassis. 23,000-lb. GVWR with spring rear suspension and hydraulic brakes.

ENGINE:

• V8-308 6.0L 308 HP @ 4400 RPM, 4600 GOV RPM, 367 LB/FT @ 4400 RPM

ENGINE EQUIPMENT:

• Frontal air intake

• Air cleaner mounted on rail

• 145 amp alternator

• (1) Alliance 931 group 31 12 volt battery

• Horizontal tailpipe, exit RH aft of rear tires

• Antifreeze to ethylene glycol pre-mixed 50/50 coolant

• Rubber coolant hoses

• No block heater

TRANSMISSION:

• 2200 HS automatic transmission with park pawl with PTO provision

TRANSMISSION EQUIPMENT:

• Water to oil transmission cooler

• Synthetic transmission fluid (TES-295 compliant)

FRONT AXLE AND EQUIPMENT:

• 8,000# drop single front axle

• WEMC hydraulic 4-piston fixed caliper disc front brakes

• Front grease seal

• TRW TAS-55 power steering

FRONT SUSPENSION:

• 8,000# taperleaf front suspension

• Maintenance free rubber bushings - front suspension

• No front sway bar

• Front shock absorbers

Item # Qty Description

REAR AXLE AND EQUIPMENT:

• 15,000# single rear axle

• 5.71 rear axle ratio

• SPL70 Dana Spicer main driveline with half round yokes

• Transmission and rear axle driveline guard

• Organic SAE 80/90 rear axle lube

• WEMC hydraulic 4-piston fixed caliper disc rear brakes

• Rear oil seals

REAR SUSPENSION:

• 15,000# taperleaf spring rear suspension with radius leaf

• Rear shock absorbers

BRAKE SYSTEM:

• Hydraulic brake package

• Wabco hydraulic 4S/4M without traction control

FUEL TANKS:

• 40 gal / 151 liter rectangular steel fuel tank - between rails

TIRES:

• Goodyear Endurance RSA 245/75R22.5 14 ply radial front tires

• Goodyear G622 RSD 245/75R22.5 14 ply radial rear tires

HUBS:

• WEMC iron rear hubs painted black

WHEELS:

• ALCOA 87340X 22.5X7.50 8-hub pilot 5.44 inset aluminum disc front wheels

• ALCOA 87340X 22.5X7.50 8-hub pilot aluminum disc rear wheels

CAB INTERIOR:

• DENSO HD A/C compressor

• Auto self-reset circuit breakers and fuses

• TRW tilt/3.00" telescopic steering column with foot actuated pedal

INSTRUMENTS & CONTROLS:

• Driver message center with LCD display, 24 warning lamps, data linked, AMI

• Electric fuel gauge & low fuel indicator lamp

• Electric speedometer

• Electronic 6000 rpm tachometer

• Electric engine oil pressure gauge w/ warning lamp & alarm

• Electric engine coolant temperature gauge w/ warning lamp & alarm

• Automatic transmission oil temperature gauge w/ warning lamp & alarm

• Engine hour meter, integral to message center LCD

• 97 dB backup alarm

• Cruise control switches

• Wagner 7212 turn signal flasher

Item # Qty Description

2.02 1 Federal Signal Back-up alarm

2.03 1 US DOT triangle reflector kit with three (3) triangles, for compliance with FMCSA regulations.

Includes plastic storage case.

3.00 BODY:

3.01 1

22’ CUSTOM BODY SPECIFICATIONS

• Length: 22'

• Width: 99" (96" Inside to Inside of Sides)

• Height: 85" Floor to Bottom of Roof Bows

CAB DOORS

• Hinged "Sedan Style" Driver's and Passenger Side Doors with Sliding Window

• Two Point Rotary Latch Hardware, Locking

• Interior Grab Handle Installed to Assist in Closing Doors

• Door Skin Is Chemically Bonded to Frame Structure

• Continuous Stainless Steel Piano Hinge

CAB FEATURES

• Cab Acoustical Insulation Package Zones

• Cab Heat & A/C with Cab Air Filter

• Dual 12V Power Points and USB Power Point On Dash

REAR STRUCTURE

• Single 32" Hinged Rear Door

• Two Point Rotary Latch Hardware, Locking

• Continuous Stainless Steel Piano Hinge

SEATING

• Driver's Seat Magnum 200 Mechanical Suspension With Arm Rests

• Jump Seat Retainers In Passenger Step Well

REAR BUMPER

• Aluminum Construction

• 10" Grip Strut Surface (12" Overall Depth)

• Width Of Rear Bumper To Be .25" Narrower Than Width Of Side Panels

• Bottom of Bumper Flush with Rear Taper

DRIVERS CONVENIENCE OPTIONS

• (2) 12 Volt Power Points on Instrument Panel

• Install USB Power Point Wired On ACC

• Cab Heater and Air Conditioning With Electric Controls And Filter

ROOF

• .040" Aluminum Skin Roof Assembly

• 1.5" Extruded Aluminum Modified H-Profile Roof Bows on 24" Centers

CARGO SIDE WALLS

• .102" Aluminum Upper and Lower Side Walls

• 16.62" Skirts Below Floor Planks BEHIND rear axle

Item # Qty Description

• 18.19" Skirts Below Floor Planks In FRONT of rear axle

• Skirt Supports On Maximum 4' Spacing

• 2.25" "Modified-H" Profile Wall Stiffeners Riveted on 24" Centers

EXTERIOR BODY OPTIONS

• Molded Lift up Hood

• Chrome Front Bumper

• Automotive Style Headlight Assemblies with Integrated Parks and Turns

• Auxiliary battery box compartment

• Door to use locking chrome recessed handle

• Box to have 2 vents 1.75" louvered vents in inboard face

EXTERIOR LIGHTING

• Clearance and Marker Lights LED

MIRRORS

• Chrome Heated Remote Mirror Assemblies

OTHER

• Standard structural warranty of 5 years or 50,000 miles and standard component warranty of 12 months or 12,000 miles.

• The vehicle shall be fully sanded on all exterior surfaces with no more than 150 grit to assure removal of imperfections in metal surface. All aluminum shall be chemically etched and primed prior to painting. Base body color shall be oven baked and painted to commercial truck standards.

3.02 3 Exterior heavy-duty fluted aluminum grab handle with rubber inserts and chrome plated stanchions installed at entry door.

3.03 2 Automatic LED courtesy light at entry door.

3.04 1 Courtesy light defeat switch.

3.05 1 24" Single C manually operated exterior entrance step

3.06 1 Flip-down aluminum step on rear bumper with Diamondback step surface and stainless-steel rails and bolt on mounts. Step shall have slots in rails for securing step in stow and down position.

3.07 1 LED Round combination stop/tail, turn and reverse lights.

3.08 1 Aluminum license plate mounting frame with LED light.

3.09 1 Entire underside shall be undercoated. Includes chassis, floor extrusions, step wells and aluminum compartments.

3.10 1 Rear mud flaps. Includes anti-sail brackets when required.

4.00 PAINT / GRAPHICS:

4.01 Body base color shall be white.

5.00

INTERIOR COLOR SELECTION:

• Wall Covering o Front/Galley room: Silver smooth Kemlite 0.075" FRP o Rear room: Chrome carpet

• Bulkheads: Silver smooth Kemlite 0.075" FRP

• Ceiling Fabric

Item # Qty Description o Center: Charcoal Gray Texture Powder Coated Aluminum o Outside ceiling: Silver Mist carpet

• Floor Covering: #150 Onyx PVC Flooring

• Office Chairs: Black

• Vinyl Coverings:

o Seat bottom to be stock Black Vinyl.

o Seat back to be Ultraleather Dwell 570-5635 Basalt back

• Cabinets: Charcoal Gray Texture Powder Coated Aluminum

• Interior door panel: Black Texture Powder Coated Aluminum

• Flip down bench seat base: Black Texture Powder Coated Aluminum

• Counters and Tables: Steel Mesh Laminate

• Overhead control console cabinet: Black laminate

6.00 DRIVER / PASSENGER CAB AREA:

6.01 1

Walk-in van custom cab area finishing.

• Cover cab doors with aluminum panels powder coated black.

• Heavy-duty rubber grab handle on each door.

• Panels covered with vinyl or fabric above driver and passenger doors.

• Vehicle height sign on dash.

• Insulated black rubber mat in driver and passenger toe plate area.

• Insulate walls in kick plate area and install black carpeted panels.

• Vehicle shall have a Final Stage Vehicle Certification and Altered Vehicle Certification as required by Federal Motor Vehicle Safety Standards (FMVSS) 49 CFR Part 567.5 and 567.7

• Payload sticker in cab area with vehicle axle load ratings and available axle payload as built.

6.02 1 Work area on passenger side covered with laminate to match rear countertops and trimmed with vinyl T-molding.

6.03 1

Custom fabricated console to house electrical distribution components and control panels shall be located in the overhead console above the windshield. The entire console shall be constructed of 3/4" plywood. The face shall be finished with laminate the bottom shall be covered with vinyl.

6.04 1 Red/Clear LED dome light with 3-position switch, red/off/white.

6.05 1 Color back up camera system with 7" LCD monitor and day/night camera. Camera includes a microphone for audio commands from a spotter to the driver during backing operations.

6.06 1 Sun visors installed below overhead console.

6.07 1 AM/FM stereo with Bluetooth and one (1) pair of 6" x 9" speakers.

7.00 WALLS, CEILING AND FLOOR:

7.01 Insulate walls with a minimum of 2-1/2" of fiberglass insulation. Cover interior body side posts with 1/2" plywood sub wall.

7.02 Cover sub wall with smooth finish Kemlite 0.075" fiberglass reinforced plastic (FRP) lining.

Wall covering shall be a continuous piece front to back, no seams acceptable.

7.03 Cover sub wall with ribbed loop pile carpet.

7.04

Insulate ceiling with a minimum of 2-1/2" of fiberglass with an R-11 rating.

• Cover interior roof beams with 1/2" plywood.

• Modular panel design allows for manageable future additions and repairs.

• Plywood Panels covered in acoustical fabric.

7.05 Floor underlayment to be 5/8" exterior grade tongue and groove structural plywood, 6 ply, face veneer plugged and sanded.

7.06 Non-skid commercial grade PVC flooring. The flooring shall be continuous, one piece full length, full width, no seams.

Item # Qty Description

7.07 Vinyl cove molding (mop board) at base of wall, 2-1/2” high. Installed where required.

7.08 1 Flush pocket door installed on heavy-duty aluminum c-channel track with two (2) three-wheel roller trucks and soft open/close feature. Pocket door shall have recessed handle and magnetic closure to keep the door open/closed.

7.09 All bulkheads shall be covered with Kemlite 0.075" FRP. Trim exposed edges of bulkheads with rounded anodized aluminum trim where applicable.

7.10 1

Cover load space door with powder coated aluminum panel with heavy-duty rubber grab handle.

Interior window covering to be a mini blind.

7.11 1

Street side mounted 30" wide x 19" high flush mount deep-tint horizontal sliding egress window with screen.

Interior window covering will be a mini blind

8.00 GALLEY:

8.01 1 Microwave oven. 1.1 cu. ft. 1000-watt

8.02 1 Keurig Coffee maker. K475

8.03 1

AC and DC powered refrigerator with the following features:

• 2.7 cu. ft. capacity.

• Freezer shelf for ice cube tray.

• Door bin holds 2-liter containers.

• Integrated door latch.

• 120/230Vac 50/60 Hz and 12/24 Vdc

9.00 SEATING:

9.01 4 Pneumatic task chair with five-star caster spider base, adjustable height and no armrests.

Chair secured with bungee cord for transit.

9.02 1 Install passenger jump seat with 2-point seat belt.

9.03 Fabricate and install fixed bench seating with removable cushions. Bench seat cushions shall be covered in heavy-duty vinyl.

9.04 Fabricate and install flip-down bench seating. Bench seat cushions shall be covered in heavy-duty vinyl. Bottom seat cushion will be installed on fold down spring loaded seat brackets.

9.05

BENCH SEAT REQUIREMENTS:

• Foam for seat backs and bottoms shall be firm density.

• All bench seating material must meet Federal Motor Vehicle Safety Standards part 571.302 Flammability of Interior Materials.

• Material corners shall be squared or angled to fit precise cut of foam.

• Foam shall be bonded to plywood backer with industrial grade adhesive.

• Attachment of fabric/vinyl to backer shall utilize industrial grade upholstery staples

10.00 CABINETS:

10.01

Custom fabricated aluminum cabinets. Cabinet specifications:

• Base cabinets constructed of 0.080" powder coated aluminum with anodized aluminum frames.

• Base cabinet doors are double shell, formed from a single sheet of 0.080" aluminum, with a 0.040" aluminum door back attached.

• Overhead cabinets constructed of 0.064"powder coated aluminum with anodized aluminum frames.

• Overhead cabinet doors are double shell, formed from a single sheet of 0.064" aluminum, with a 0.040" aluminum door back attached.

• Overhead cabinet doors swing up and gas spring lift supports.

Item # Qty Description

10.02 1 LED light under overhead cabinet. Galley

10.03 1 Magnetic dry erase board framed in aluminum. Includes aluminum clip frame for ease of board replacement, sized as required.

10.04 Countertops shall be covered in 0.040" Wilsonart laminate. All exposed edges shall be covered with heavy duty flexible PVC T-molding.

10.05 Conference table covered in 0.040" Wilsonart laminate. All exposed edges shall be covered with heavy duty flexible PVC T-molding.

10.06 1 Powder coated 0.125" aluminum conference table base.

10.07 1 Powder coated 0.125" aluminum table leg.

11.00 HVAC SYSTEM:

11.01 1 Fan-tastic Vent model 1450 3-speed reversible 12" power roof ventilator.

11.02 2

Low profile rooftop air conditioner with wall mounted thermostat. Includes:

• 13,500 nominal Btu/hr air conditioner with condensate pump.

• Ceiling assembly with 6,000 Btu/hr heat strip

• Wall mounted thermostat

11.03 2 Broan model 174 wall mount 5,120 Btu/hr electric heater.

12.00 AC ELECTRICAL SYSTEM:

12.01 1

15-kW 120/240Vac liquid-cooled gasoline generator, installed in a custom fabricated compartment. Generator features:

• Prime Power (100% output 24/7 at up to 70˚F and 500ft elevation)

• USTC Certified Manufacturer

• 3 year/2000 hour Warranty with nationwide service network

• Sound reduction enclosure

• Four point mounting system

• Four-cycle water cooled gasoline engine

• Radiator cooled, direct mounted and protected enclosure

• High-coolant temp and low oil pressure shutdown sensors

• Spin-on oil filter and in-line fuel filter

• Single side and bottom service

Compartment shall be constructed to the following specifications:

• Compartment shall be constructed from 0.187" aluminum with all welded seams.

• Compartment shall have 0.125" aluminum 2" box pan doors and 0.125" aluminum frames.

• Door frames shall be riveted to the body and welded to the compartments.

• Doors shall have stainless steel hinges attached to the doors and door frames with stainless machine screws.

• Doors shall have slam latches and flush mounted handles.

• Doors shall have 0.100" aluminum treadplate panels on interior surfaces

• Doors shall be held open in a 90° position with gas charged lift/support cylinders.

• Doors shall be sealed with industrial grade neoprene gasket.

Generator exhaust shall be routed to the street side of the vehicle.

12.02 1

ACData surge suppressor for protection of entire AC power system features:

• UL listed: UL1449 3rd Edition

• LED visual verification of status

Item # Qty Description

12.03 1

60A-120/240Vac and 12Vdc combined electrical control panel with the following features:

• Generator and shore power main breakers

• Six (6) AC UL listed magnetic/hydraulic branch circuit breakers with LED indicators

• Six (6) DC UL listed magnetic/hydraulic circuit breakers with LED indicators

• Digital AC meters: voltage, amperage

• Digital DC voltmeter

• Generator stop/start switch, generator hour meter

12.04 120Vac auxiliary control panels as required with UL listed magnetic/hydraulic circuit breakers and LED indicators.

12.05 1

50A-125/250Vac shore power package including:

• Waterproof shore power inlet with cap

• 50-ft. 50A-125/250Vac shore power cord

• 6-ft. 50A-125/250Vac pigtail

12.06 2

20A-125Vac duplex receptacle. Receptacle not dedicated to any installed equipment.

• One (1) electronics rack

• One (1) printer (future)

12.07 8

20A-125Vac duplex receptacle with dual USB charging ports. Receptacle not dedicated to any installed equipment.

• One (1) per workstation [qty. 4]

• One (1) per between workstation 3/4

• Two (2) conference table base

• One (1) passenger front workstation

12.08 1

20A-125Vac GFCI duplex receptacle. These receptacles are not dedicated to any installed equipment.

Galley

12.09 2 20A-125Vac exterior GFCI duplex receptacle.

Receptacle will be installed with a weatherproof cover.

12.10 Wire chase wire management raceway system.

12.11

AC WIRING REQUIREMENTS:

• All AC main wiring shall be stranded THHN wire and run in non-metallic Carlon Carflex liquid tight conduit.

• All AC branch circuit wiring shall be stranded THHN wire (AWG 12 minimum) and run in nonmetallic Carlon Carflex liquid tight and Carlon Flex-Plus blue ENT conduit.

• All electrical circuits and appliances shall conform to applicable national electrical codes.

13.00 DC ELECTRICAL SYSTEM:

13.01

• Four (4) Lead acid deep-cycle 6Vdc batteries. Batteries shall be installed underbody in slide out weather resistant aluminum compartment. Compartment shall have box pan door with slam latch, flush mount handle, key lock and Kwikee heavy-duty slide assembly. Two (2) batteries will be separated for auxiliary equipment (2.2 hours of capacity @ 75-amp discharge rate) and two (2) batteries will be for communications equipment (2.2 hours of capacity @ 75-amp discharge rate). Battery data assumes a usable voltage range of 13.6 to 10.5 volts.

• Two (2) electronic converter/chargers, 80 amp minimum output each. Converter/charger features:

• Charges three banks of batteries at the same time.

• UL listed for safety.

Item # Qty Description

• Manual reset circuit breaker.

• Reverse battery protection.

• Electronic current limiting.

• High voltage protection.

• One (1) master disconnect switch to control the auxiliary battery systems.

• 12Vdc auxiliary panels with UL listed magnetic/hydraulic circuit breakers as required.

• 12Vdc auxiliary digital voltmeter to monitor the communications battery system.

13.02 18 Light, 6" LED, neutral white with polished bezel.

13.03 5 LED Scene Light. 12VDC with chrome flange

Two (2) per side

13.04

12VDC WIRING REQUIREMENTS:

• 2-gauge minimum copper stranded battery cable shall be used for 12Vdc main supply lines.

All cable runs shall be full length, no splices. All cable terminals shall be staked and soldered.

All cable shall be enclosed in convoluted polyethylene tubing and the ends of the cable shall be sealed with color-coded shrink-wrap identifying the function of the cable.

• All added electrical branch circuits shall be protected from over-current by resettable circuit breakers appropriately rated for the load. Only circuit breakers shall be used in the installation of added electrical branch circuit wiring (plug type fuses are unacceptable).

• Circuit breaker functions shall be identified by engraved or printed labels.

• All added wiring for load runs of AWG 10, 12, 14, and 18, shall conform to MIL-W-16878/2 and/or UL1007/1569”

• All added wiring for load runs of AWG 8, shall conform to MIL-W-16878/3 and/or UL1028

• Wire terminals for added circuits must conform to MIL-T-7928. Terminals shall be insulated, insulation grip, TYPE II, CLASS 2 and shall be crimped with tooling recommended by the terminal manufacturer.

• All wiring shall be numbered or lettered on 6" centers minimum.

• Wiring shall be protected from chafing and abrasion with convoluted polyethylene tubing (wire loom) as required.

• Where wire passes through sheet metal, bulkheads and structural supports, plastic grommets shall be used to protect both wiring and wire looms.

• All wire bundles shall be tied with trimmed nylon ties.

• Care shall be exercised to provide for easy serviceability of the system in future years.

• Care must be taken in the installation to avoid the engine manifold, engine exhaust, and muffler, which could expose the wiring to severe overheating during long periods of operation. Proper insulation and heat deflection panels must be installed in such areas.

• A high-current 12Vdc system wiring schematic shall be provided.

14.00 EMERGENCY LIGHTING / SIRENS:

14.01 1

Whelen 295SLSA6 siren with 9 low current lighting control switches. California Title 13 compliant.

Slide Bar Positions Control:

1. Rear (Upper and Lower)

2. Rear (Upper and Lower), All Upper, Front Wall or "Light bar"

3. All

14.02 1 Whelen SA315P high performance, multi-port 100 watt speaker with Whelen SAK1 mount.

Item # Qty Description

14.03 1 Whelen TLIR ION-T- Series™ Linear Super-LED® Red with clear outer lens & TIONFC chrome flange.

14.04 1 Whelen TLIB ION-T- Series™ Linear Super-LED® Blue with clear outer lens & TIONFC chrome flange.

14.05 7 Whelen M6 series, M6RC (or current model), Linear Super-LED lighthead with internal flasher, RED LED's with CLEAR outer lens. Includes M6FC chrome flange.

14.06 7 Whelen M6 series, M6BC (or current model), Linear Super-LED lighthead with internal flasher, BLUE LED's with CLEAR outer lens. Includes M6FC chrome flange.

14.07 1 Custom fabricated bracket to mount M6 series light above windshield, painted to match body.

15.00 AUDIO / VIDEO:

15.01 1

32" QLED TV with wall mount bracket. Product features:

• Resolution 4K

• (3) HDMI, (2) USB

• (2) Speakers

• DTV Tuner/ATSC / Clear QAM

• Dimensions: 28.5"(W) x 16.8"(H) x 1.2"(D) Weight 11.7lbs

Rear room, centered between workstation #2/#4.

15.02 2

50" QLED TV with wall mount bracket. Product features:

• Resolution 4K

• (3) HDMI, (2) USB

• (2) Speakers

• DTV Tuner/ATSC / Clear QAM

• Dimensions: 44"(W) x 25.4"(H) x 1"(D) Weight 25.4lbs

Front conference room, one (1) per side

15.03 1 Digital HDTV Antenna + Mount with DTV Signal Meter.

No crank up, built in Amplifier and 360° rotation for improved reception.

15.04 1

4X4 HDMI Matrix Switcher. 4K HDR HDCP 2.2

Inputs:

• HDMI input at conference table Outputs:

• Three TV's

15.05 1 HDMI input jack, wall plate and cable.

HDMI input jack at front conference room table leg to matrix switcher.

15.06 HDMI connection cables, as required.

15.07 All RF cable for DSS antenna systems (when specified) shall be Belden #9116 series 6 broadband coaxial cable. All other video cabling shall be Belden #1505A RG-6/U precision video cable.

16.00 MAST AND MAST MOUNTED EQUIPMENT:

16.01 1

Prewire and make installation provisions for customer installed mast on rear of vehicle.

Includes:

• Internal support structure for future mast install on rear of truck

• Carlon Carflex ENT conduit routed from mast location to equipment rack cabinet for camera wiring (camera not included).

• Receptacle for mast compressor on dedicated circuit (compressor not included).

Item # Qty Description

17.00 RADIOS:

17.01

Primary 12Vdc power leads for communications radios shall be minimum 2-gauge copper stranded wire with soldered crimp-on end connectors (gauge based on radio requirements).

Cables shall be enclosed in convoluted tubing and function identified with colored shrink-wrap.

Power to radios shall be controlled by a continuous-duty switch actuated by the auxiliary battery disconnect switch.

17.02 2

Prewire and make installation provisions for communications radio. Installation includes:

• NMO-style base on the roof or antenna raceway, as applicable.

• LMR195 antenna cable routed to radio transceiver location in Carlon Carflex ENT conduit.

• 12Vdc power routed to radio transceiver location.

One (1) driver One (1) rear curbside workstations #3/#4

17.03 Install hinged panels under countertops to conceal radio transceivers.

17.04

Single 3"H x 3"W x 12’L square aluminum tube antenna raceway on the roof of the apparatus.

Antenna raceway will penetrate the roof at one location, to be determined. Includes the following:

• 3" high x 3" long aluminum access cover at each antenna base location on the side of the tubing for access to antenna base and coax cable.

• Access covers with watertight gasket and attached with four (4) stainless steel machine screws. Raceway tube to have nut-serts installed for access cover attachment.

• Carlon Carflex ENT conduit routed from antenna raceway penetration location to radio transceiver locations.

18.00 COMPUTER NETWORK AND EQUIPMENT:

18.01 8

RJ-45 Cat6 computer network jack with Cat6 cable routed through Carlon Flex-Plus ENT conduit or raceway (as applicable).

• One (1) per workstation [qty. 4]

• Two (2) conference table base

• One (1) passenger front workstation

• One (1) printer

18.02 1 Leviton 69270-U24 24-port Cat6 rack mount patch panel.

18.03 1 Cable Certification Report confirming that network wiring complies with Cat6 specifications.

18.04 1 Prewire and make installation provisions for customer owned 4G wireless router with single modem. Includes two (2) roof mounted NMO antenna base with rain caps.

Note: Roof mounted antennas, service contract, activation and configuration not included.

19.00 MISCELLANEOUS ELECTRONICS:

19.01 1

Custom fabricated mounting system to secure fourteen (14) space 19" wide x 23.25” depth open framed EIA electronics equipment rack with sliding rail system and swivel base. Rack to easily slide out and swivel from its fixed position allowing full access to rack mounted equipment. 200lb weight limit.

19.02 1 Rack front door with key lock.

19.03 1 Fan tray, with three (3) 69 cfm ventilation fans.

19.04 1 15 amp power strip with eight (8) outlets with mounting bracket.

20.00 EXTERIOR STORAGE COMPARTMENTS:

20.01 1 Single door underbody storage compartment with approximate interior dimensions 15" high x up to 36" wide x 25" deep constructed from 0.125" aluminum with all welded seams.

Item # Qty Description

20.02

Compartments listed above will be constructed to the following specifications:

• Sweep out type bottoms with 1/2” drain holes.

• 2" box pan doors and door frames fabricated from 0.125" aluminum.

• Door frames shall be riveted to the body and welded to the compartments.

• Compartments shall have an LED light that illuminates when the door is opened.

Compartment doors will be constructed to the following specifications:

• Stainless steel hinges attached with stainless machine screws.

• Slam latches and flush mounted handles.

• 0.100" bright polished aluminum diamond plate on interior surfaces fastened with stainless hardware.

• All doors shall be sealed with industrial grade neoprene gasket.

21.00 MISCELLANEOUS OTHER:

21.01 2 5 pound dry chemical fire extinguisher.

21.02 2 Battery powered combination Carbon Monoxide and Smoke alarm.

21.03 1

Complete manual set, including the following (as applicable):

• As-built specifications with interior and exterior drawings as used for production of the vehicle.

• Chassis and body owner's manuals.

• 12Vdc and 120Vac legends showing wire gauge, color, number and function.

• 12Vdc high current wiring diagram illustrating the battery system, isolators, power converters, alternator, disconnect switches and control panels.

• Roof top antenna placement drawing and legend identifying antenna placements and termination points.

• Audio/Video cabling diagram.

• Warranty and Return Authorization procedures.

• Chassis and generator maintenance and service logs.

• Battery maintenance information.

• All individual component manuals and warranty registration cards as provided by component manufacturers. Customer is responsible for completing warranty cards and mailing them to manufacturers.

21.04 1

TRAINING.

Company representative to provide up to four (4) hours of orientation on the provided systems, as applicable:

• Generator start up and shut down procedure

• Leveling system operation

• AC and DC electrical systems operation

• HVAC systems operation

• Audio/Video system operation, does not include programming DVR's, TV's, etc.

21.05 Warranty of no less than one (1) year/12,000 miles, whichever comes first, for manufacturer’s defects in materials and workmanship.