Attachment D. Design and Specifications.pdf

' 0

60' 0"

' 0

60' 0"

' 7

/1 6"

' 1

9/

47' 11 9/16"

14' 0"

72' 0"

' 0

72' 0"

45' 8 1/8" 14' 1/8"

15' 7 7/8"38' 9 5/8"

' 0

44' 11"

' 0

44' 11"

' 8

/1

6"

22' 3 15/16"

17' 9 11/16"

' 2

20' 0"

' 0

3' 0"

' 0

3' 0"

' 0

3' 0"

' 0

3' 0"

6' 6 7

/16

' 4

48' 5/16"

40' 1"

' 3

/1 6"

' 6

5/

29' 7 1/4"

10' 0"

20' 8 1/2" 3 13/16"

5'

/8

"10 ' 1

1/

' 1

3/

4"

23' 4"

12' 0"

' 8

' 0

' 1

9/

14' 8 1/16"

28' 8" 13' 8"

13' 7"

' 1

/1 6" 12' 0"24' 0"

26' 8"

8' 0"

14' 11 1/2"

24' 1/2"

12' 0"

' 0

' 4

3' 7 1/2"

3' 1/4"

3'

3' 9 5/8"

2' 11 3/4"4' 5 11/16"

5'

2' 8" 8' 0"

6'

" 12 ' 7

/2

' 1

/8

' 0

11' 4 3/8"

' 1

/1 6"

' 2

5/

52'x14' alley constructed with 2 7/8 top rail, 4 rails >2" with 2x10 pressure treated boards mounted between 2nd and 3rd rails

20'x14' bud box

14' gate with solid wall closes off bud box.

overhead brace on gateway bud box constructed with 2 7/8 top rail, 4 rails >2" with 2x10 pressure treated boards mounted between middle 3 rails sliding gates at left corners of bud box to close off race and loadout

3' x24' load out platform is 40" from ground

8' gooseneck load out gate swings in off load out

10' gooseneck wing gate swings out from bud box. wing gate has drop peg to lock in place process sort pen constructed with 2 7/8 top rail, 4 rails >2" with 2x10 pressure treated boards mounted between 2nd and 3rd rails

14' gate in front of chute overhead brace to corner of load pen gate swings to sort three ways out of chute process pen, load pen and process sort pen

6' gate swings off corner of load pen to block chute work area chute work area

45'x 36' load pen left and top sides constructed with sucker rod right and bottom constructed same as alley

14' intersection with overhead braces gates on right left and bottom sides

48'x74' branding pen all 4 sides constructed with 2 7/8 top rail and 5 rails of 1' sucker rod posts 8 ft spacing at least 60" hight

12' entry gate to parking lot with overhead brace

12' entry gate to old corral with overhead brace

6' 5 3/8"

4' 0"6' 1 1/8"

4' man gate

4 rivers leadup 3x7'x3' sections total length 21'

6' gate for chute access

Attachment D-1. Corral Design

Process sort pen, bud box, and alley shall be lightly graded before construction to remove vegetation and provide for flat, elevated working surace.

*All metal pipe used for corral shall be C-class oil-field pipe. After construction, pipe shall be pre-treated with Rust Cure Paint Pretreatment,or approved equal, and then painted white with Rust-oleum Aluminum Paint, or approved equal.*

3' man gate fla t fla t sta ir sta ir sta ir sta ir s l o p e d u p s l o p e d u p gooseneck loadout gate wall sections on inside of curve are 4' between posts stairs use 2"x10" pressure treated slope up, platform and catwalk platform use 2"x12" pressure treaded laid long ways with angle iron supports underneath upright posts and top rail are 2 7/8" middle 4 rails are at least 2" diameter spaced 10" between. 2"x10" pressure treated boards mounted between bottom 4 rails and ground height of top rail 62" height of platform is 40"

4' man gate at top of platform for truck access. hinges on truck side of platformw stairs to platform are 10" step up overhead braces are 7' high from platform and ground level load out is angled for straight shot side load from load out to rocking martini gate curve is split into three curved sections with 4' inside wall of curve on all 3 sections gooseneck load out section is straight load out width is 3' between posts catwalk width is 3' between posts curve curve curve gooseneck load out gate

Attachment D-2.

Loadout Design

Attachment D-3. HDPE 4-rail Fence Specifications