Attachment 8 - Narrative 03 402-318_Augusta_RRTP_IFB_.pdf

LEHE0138-01 Page 1 of 4

EMCP 4

Features General Description The Cat® EMCP 4.2 offers fully featured power metering, protective relaying and engine and generator control and monitoring. Engine and generator controls, diagnostics, and operating information are accessible via the control panel keypads; diagnostics from the EMCP 4 optional modules can be viewed and reset through the EMCP 4.2.

Full Range of Attachments

• Wide range of system expansion attachments, designed specifically to work with the EMCP 4.

• Flexible packaging options for easy and cost effective installation.

World Wide Product Support

• Cat dealers provide extensive pre and post sale support.

• Cat dealers have over 1,600 dealer branch stores operating in 200 countries.

Features

• A 33 x 132 pixel, 3.8 inch, graphical display denotes text alarm/event descriptions, set points, engine and generator monitoring, and is visible in all lighting conditions.

• Textual display with support for 28 languages, including character languages such as Arabic, Chinese, and Japanese.

• Advanced engine monitoring is available on systems with an electronic engine control module.

• Integration with the Cat Digital Voltage Regulator (CDVR) provides enhanced system performance.

• Fully featured power metering, protective relaying, engine and generator parameter viewing, and expanded AC metering are all integrated into this controller.

EMCP 4.2

Caterpillar is leading the power generation market place with power solutions engineered to deliver unmatched performance, reliability, durability and cost-effectiveness.

• Real-time clock allows for date and time stamping of diagnostics and events in the control’s logs as well as service maintenance reminders based on engine operating hours or calendar days.

• Up to 40 diagnostic events are stored in the non- volatile memory.

• Ability to view and reset diagnostics on EMCP 4 optional modules via the control panel removes the need for a separate service tool for troubleshooting.

• Set points and software stored in non-volatile memory, preventing loss during a power outage.

• Reduced power mode offers a low power state to minimize battery power requirements.

• Three levels of security allow for configurable operator privileges.

• Selectable units − Temperature: °C or °F − Pressure: psi, kPa, bar − Fuel Consumption: Gal/hr or Liter/hr

Standards

• UL Recognized

• CSA C22.2 No.100, 14, 94

• Complies with all necessary standards for

CE Certification 98/37/EC Machinery Directive

– BS EN 60204-1 Safety of Machinery 89/336/EEC EMC Directive

– BS EN 50081-1 Emissions Standard

– BS EN 50082-2 Immunity Standard 73/23/EEC Low Voltage Directive

– EN 50178 LVD Standard

• IEC529, IEC60034-5, IEC61131-3

• MIL STND 461

Image shown may not reflect actual package

EMCP Generator Set Controller

Standard Features Generator Monitoring • Voltage (L-L, L-N)

• Current (Phase)

• Average Volt, Amp, Frequency

• kW, kVAr, kVA (Average, Phase, %)

• Power Factor (Average, Phase)

• kW-hr, kVAr-hr (total)

• Excitation voltage and current (with CDVR)

• Generator stator and bearing temp (with optional module)

Generator Protection • Generator phase sequence

• Over/Under voltage (27/59)

• Over/Under frequency (81 O/U)

• Reverse Power (kW) (32)

• Reverse Reactive Power (kVAr) (32RV)

• Overcurrent (50/51)

Engine Monitoring • Coolant temperature

• Oil pressure

• Engine speed (RPM)

• Battery voltage

• Run hours

• Crank attempt and successful start counter

• Enhanced engine monitoring (with electronic engines)

Engine Protection • Control switch not in auto (alarm)

• High coolant temp (alarm and shutdown)

• Low coolant temp (alarm)

• Low coolant level (alarm)

• High engine oil temp (alarm and shutdown)

Control • Run / Auto / Stop control

• Speed and voltage adjust

• Local and remote emergency stop

• Remote start/stop

• Cycle crank

Inputs & Outputs • Two dedicated digital inputs

• Six programmable digital inputs

• Six programmable form A dry contacts

• Two programmable form C dry contacts

• Two digital outputs

Communications • Primary and accessory CAN data links

• RS-485 annunciator data link

• Modbus RTU (RS-485 Half duplex)

Language Support Arabic, Bulgarian, Chinese, Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek, Hungarian, Icelandic, Italian, Latvian, Lithuanian, Japanese, Norwegian, Polish, Portuguese, Romanian, Russian, Slovak, Slovene, Spanish, Swedish, Turkish

Environmental • Control module operating temperature: –40°C to 70°C

• Display operating temperature: –20°C to 70°C

• Humidity: 100% condensing 30°C to 60°C

• Storage temperature: –40°C to 85°C

• Vibration: Random profile, 24-1000 Hz, 4.3G rms

LEHE0138-01 Page 2 of 4

Optional Modules

LEHE0138-01 Page 3 of 4

CAN Annunicator The EMCP 4 CAN Annunciator serves to display genset system alarm conditions and status indi-cations. The annunciator has been designed for use on the accessory communication network and may be used in either local (package mounted) or remote (up to 800 feet) application. A maximum of three annunciators may be used with a single

EMCP 4.2.

RS-485 Annunciator The EMCP 4 RS-485 Annunciator serves to display genset system alarm conditions and status indica-tions. The annunciator has been designed for use on the long distance annunciator datalink and is used for remote (up to 4000 feet) application.

Remote Monitoring Software The EMCP 4 remote monitoring software package is a PC based program which allows the user to monitor and control a generator set, and is capable of running on a Windows based operating system.

The remote monitoring software allows the user to configure data monitoring and data acquisition processes for monitoring, graphing, and logging of genset data.

Optional Modules

Digital Input/Output Module The Digital Input/Output (DI/O) module serves to provide expandable Input and Output capability of the EMCP 4 and is capable of reading 12 digital inputs and setting 8 relay outputs. The DI/O mod-ule has been designed for use on the accessory Communication Network and may be used in either local (package mounted) or remote (up to 800 feet) application. A maximum of four DI/O modules may be used with a single EMCP 4.2.

RTD Module The RTD module serves to provide expandable generator temperature monitoring capability of the EMCP 4 and is capable of reading up to eight type 2-wire, 3-wire and 4-wire RTD inputs. The RTD Module has been designed for use on the Acces-sory Communication Network and may be used in either local (package mounted) or remote (up to 800 feet) application. A maximum of one RTD Module may be used with a single EMCP 4.2.

Thermocouple Module The thermocouple module serves to provide expandable engine and generator temperature monitoring capability of the EMCP 4 and is capable of reading up to twenty Type J or K thermocou-ple inputs. The thermocouple module has been designed for use on the accessory communication Network and may be used in either local (package mounted) or remote (up to 800 feet) application.

Information contained in this publication may be considered confidential. Discretion is recommended when distributing.

Materials and specifications are subject to change without notice.

CAT, CATERPILLAR, LET’S DO THE WORK, their respective logos, “Caterpillar Yellow,” the “Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.

www.cat,com/electricpower ©2019 Caterpillar

All rights reserved.LEHE0138-01 (03/19)

LEHE0141-05 Page 1 of 2

Battery Charger

Features

● Electronically current limited at 105% of rated output

Standards

UL 10 Amp Battery Charger

electrolyte.

Listing.

Image Shown may not Reflect Actual Package.

Battery Charger

of Caterpillar and may not be used without permission.

www.cat,com/electricpower

Specifications Input supply 110 – 120 V

208 – 240 V

AC and DC fuses 2 input and 2 output)

Output voltage 24V

Output amps 10

Frequency 50 / 60 Hz

Operating temperature -20°C ( -4°F) to +60°C (140°F)

Housing constructed of rustproof anodized Aluminum

Dimensions

Width Depth Height Weight

195 mm (7.66 in) 165 mm (6.5 in) 318 mm (12.5 in) 10.4 kg (23 lb)

NFPA 110 alarm package as follows:

Feature Codes:

BTC1024 BTC1028 BTC1035 BTC1025 BTC1032

LEHE0141-05 (02/19)

Ima ge Shown may n not Reflect Actua

Facto starti meta remo silico comm heat maxi ory installed j ing capability l heater with ote engine mo one hoses an mon connecti er and thermo mum coolant acket water h . The system an integral h ounted contro d heater cont ion point in th ostat location flow and hea eater for incr includes a ta igh limit ther ol thermostat, rol relay wire he control pan is optimized ating power e

H eased cold-ank-style mostat and a durable d to a nel. The for fficiency.

Jacket Water Heater

Factory installed jacket water heater for increased cold-starting capability. The system includes a tank- style metal heater with an integral high limit thermostat and a remote engine mounted control thermostat, durable silicone hoses and heater control relay wired to a common connection point in the control panel. The heater and thermostat location is optimized for maximum coolant flow and heating power efficiency.

FEATURES

FACTORY INSTALLED

SPECIFICATIONS

Complete with silicone hoses

Isolated tank heater vibration and shock tested to extreme limits to guarantee durability

Optimized location of the heater on the genset base for maximum coolant flow

Remote pilot thermostat located on the engine for optimized power cycle efficiency is factory set to 100° F (37.8°C)

Automatically disconnected when engine is running via a dedicated heater relay located in the control panel.

Supplied with UL recognized components

Compatible with Cat ELC and all chemicals

All parts are serviceable and field replaceable

Incoloy heater element for longer service life

Unit Specification

Design Voltage

208 V 220 V 240 V

Feature

Code

JWH0059/JWH00573

Jacket Water Heater

LEHE0297-04

Rating 2250 W 2520 W 3000 W

Frequency 50/60 Hz 50/60 Hz

Phase 1 1 1

Amps 10.82 11.45 12.5

50/60 Hz

WIRING DIAGRAMS

Jacket Water Heater

LEHE0297-04

Wiring diagram reference for 240V or 208V Line to Line and 120V Line to Neutral power connection (Note: Including

Optional Space Heater and Battery

Charger)

Wiring diagram reference for 240V Line to

Neutral power connection

HEATER DETAIL

HEATER OPERATION

The heater uses compliant components to UL and CSA, and is both CSA and UL approved.

When the generator set is not running, the heater is automatically connected to the AC supply through a power relay mounted in the control panel. Upon receiving a start signal, the AC supply is automatically disconnected by the power relay and automatically reconnected when the start signal is removed and the engine has stopped.

Pilot thermostat located on the engine precisely monitors and controls the engine coolant temperature and is wired to energize and de-energize heater power cycles.

A high-limit thermostat is built into the heater to regulate the output temperature to within safe limits.

www.Cat.com/electricpower © 2020 Caterpillar. All Rights Reserved. CAT, CATERPILLAR, LET’S DO THE WORK, their respective logos, "Caterpillar Corporate Yellow", the "Power Edge" and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission

LEHE0 297-04 (11/20)

Jacket Water Heater

Attachments

EMCP 4

RS-485 Annunciator The EMCP 4 RS-485 annunciator serves to display generator set system alarm conditions and status indications. The annunciator has been designed for use on the EMCP 4 RS-485 annunciator data link for remote applications, providing customers with enhanced site flexibility.

The EMCP 4 annunciator is configurable to the standards of NFPA 99/110 for emergency standby generator systems.

Features

• The EMCP 4 annunciator provides sixteen

(16) individual points of annunciation, with two (2) LED’s included for each point.

• An additional pair of LED’s provides status indication of the RS-485 communication network.

• Includes alarm horn with lamp test and alarm acknowledge pushbuttons.

• Configurable to NFPA 99/110 requirements for local and remote annunciation on emergency standby generator systems.

• Provides custom label kit including software for customer’s specific alarms and arrangement

• Designed and tested to meet stringent impulse shock and operating vibration requirements

• Uses high quality shielded twisted-triad cable for robust remote communications

• Graphic symbols are provided next to each pair to indicate various alarms and events

• The annunciator can be mounted remotely up to 1200 m (4,000 ft).

• Provides superior visibility of the LED’s in direct sunlight. footprint

Minimal maintenance costs

Superior step load response Specifications

Technical Data Electrical Battery Voltage Functional Range: 9 to 32 VDC Power Consumption Maximum: _ 12 watt at 24 VDC Standby: _ 5 watt at 24 VDC Control Power: 12-24 VDC Communication: RS-485 Single, 8-pin Connector Alarm Sound Level 80 db

Physical Weight 2.5 lb or _ 1.13 kg

Environmental Operating Temperature –40° C to 70° C

–40° F to 158° F Storage Temperature –50° C to 70° C

–58° F to 158° F Relative Humidity 90%

Certifications UL Recognized trained to support every aspect of your Cat UPS system.

Picture shown may not reflect actual configuration.

Shown with Optional Equipment.

LEHE0142-02

Attachments

LED Color Scheme

Each pair of LED’s on the annunciator consists of two of three colors: green, yellow and red, which allows for custom configuration of status, warning and shutdown conditions.

The available colors and combinations are:

LED Color Scheme

• Emergency stop shutdown

• Overcrank shutdown

• Low coolant temperature warning

• High coolant temperature warning/shutdown

• Low oil pressure warning/shutdown

• Overspeed warning/shutdown

• Low coolant level warning/shutdown

• Low fuel level warning/shutdown

• EPS supplying load status

• Control switch not in auto warning

• High battery voltage warning/shutdown

• Low battery voltage warning/shutdown

• BATT charger AC failure warning/shutdown

• Low cranking voltage

• Engine running

• Tier 4 SCR

Materials and specifications are subject to change without notice.

CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow,” the “Power Edge” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.

www.CatElectricPower.com

©2016 Caterpillar All rights reserved. LEHE0142-02 (03/16) Page 660 of 2569

BLT Series LED

2BLT2

2' x 2'

LED

COMMERCIAL INDOOR BLT-2X2

Catalog Number

Notes

TypeFEATURES & SPECIFICATIONS INTENDED USE — The BLT Best-in-Value Low Profile LED luminaire features a popular center basket design that offers a clean, versatile style and volumetric distribution. High efficacy LED light engines deliver energy savings and low maintenance compared to traditional sources. An extensive selection of configurations and options make the BLT the perfect choice for many lighting applications including schools, offices and other commercial spaces, retail, hospitals and healthcare facilities. The low profile BLT design (2-3/8") also makes it an excellent choice for renovation projects.

CONSTRUCTION — Prior to fabrication, BLT components are coated with a proprietary paint blend and die-formed for dimensional consistency.

The BLT reflector is available in both smooth and ribbed finishes. Choose RB from the fixture style section below for a ribbed finish.

End plates contain easy-to-position integral T-bar clips for securely attaching the luminaire to the T-grid.

For additional T-grid security, optional screw on T-bar clips are available.

Diffusers are extruded from impact modified acrylic for increased durability.

LED boards and drivers are accessible from the plenum.

OPTICS — Volumetric illumination is achieved by creating an optimal mix of light to walls, partitions and vertical and horizontal work surfaces – rendering the interior space, objects and occupants in a more balanced, complimentary luminous environment. High performance extruded acrylic diffusers conceal LEDs and efficiently deliver light in a volumetric distribution. Four diffuser choices available - curved and square designs with ribbed or a smooth frosted finish.

ELECTRICAL — Long-life LEDs, coupled with high-efficiency drivers, provide superior quantity and quality of illumination for extended service life. 80% LED lumen maintenance at 60,000 hours (L80/60,000). Color Variation within 3-step MacAdam ellipse (3SDCM).

Non-Configurable BLT: Generic 0-10 volt dimming driver. Dims to 10% Configurable BLT: available in High Efficiency (HE) versions for applications where a lower wattage (over the standard product) is required. The High Efficiency versions deliver >130 LPW and can be specified via the Lumen Package designations in the Ordering Information below.

eldoLED driver options deliver choice of dimming range, and choices for control, while assuring flicker-free, low-current inrush, 89% efficiency and low EMI.

Optional integrated nLight®controls make each luminaire addressable - allowing them to digitally communicate with other nLight enabled controls such as dimmers, switches, occupancy sensors and photocontrols. Connection to nLight is simple. It can be accomplished with integrated nLight AIR wireless rIO and rES7 sensors, or through standard Cat-5 cabling. nLight offers unique plug-and-play convenience as devices and luminaires automatically discover each other and self-commission. nLight AIR is commissioned easily through an intuitive model app.

Lumen Management: Unique lumen management system (option N80) provides on board intelligence that actively manages the LED light source so that constant lumen output is maintained over the system life, preventing the energy waste created by the traditional practice of over-lighting.

Step-level dimming option allows system to be switched to 50% power for compliance with common energy codes while maintaining fixture appearance.

Driver disconnect provided where required to comply with US and Canadian codes.

SENSOR— Integrated sensor (individual control): Sensor Switch MSD7ADCX ((Passive infrared (PIR)) or MSDPDT7ADCX ((PIR/Microphonics Dual Tech (PDT)) integrated occupancy sensor/automatic dimming photocell allows the luminaire to power off when the space is unoccupied or enough ambient light is entering the space. See page 4 for more details on the integrated sensor.

Integrated Sensor (nLight Wired Networking): This sensor is nLight-enabled, meaning it has the ability to communicate over an nLight network. When wired, using CAT-5 cabling, with other nLight-enabled sensors, power packs, or WallPods, an nLight control zone is created. Once linked to a Gateway, directly or via a Bridge, the zone becomes capable of remote status monitoring and control via SensorView software.

See page 4 for the nLight sensor options.

Integrated Smart Sensor (nLight Air Wireless Platform): The RES7 sensor is nLight AIR enabled, meaning it has the ability to communicate over the wireless nLight control platform. It is available with an automatic dimming photocell, and either a digital PIR or a microphonics (PDT) dual technology occupancy sensor. It pairs to other luminaires and wall switches through our mobile app, CLAIRITY, which allows for simple sensor adjustment. See page 4 for more details on the Integrated Smart Sensor.

Integrated Wireless Sensor (single room control): Sensor Switch VERTEX JOT or JOTVTX15 luminaire-embedded occupancy and ambient light sensor allows the luminaire to power off when the space is unoccupied or when enough ambient light is entering the space. See page X for more details on the integrated wireless sensor.

INSTALLATION — The BLT’s low profile design of only 2-3/8” provides increased installation flexibility especially in restrictive plenum applications. The BLT fits into standard 15/16” and narrow 9/16” T-grid ceiling systems.

Suitable for damp location.

For recessed mounting in hard ceiling applications, Drywall Grid Adapters (DGA) are available as an accessory.

See Accessories section.

LISTINGS — CSA Certified to meet U.S. and Canadian standards. IC rated.

DesignLights Consortium® (DLC) Premium qualified product. Not all versions of this product may be DLC Premium qualified. Please check the DLC Qualified Products List at www.designlights.org/QPL to confirm which versions are qualified.

WARRANTY — 5-year limited warranty. Complete warranty terms located at:

www.acuitybrands.com/resources/terms-and-conditions

NOTE: Actual performance may differ as a result of end-user environment and application.

All values are design or typical values, measured under laboratory conditions at 25 °C.

Specifications subject to change without notice.

Specifications

Length: 23-3/4 (60.3)

Width: 23-3/4 (60.3)

Depth: 2-3/8 (6.0)

Depth with Air supply/return: 2-3/4 (6.9)

All dimensions are inches (centimeters) unless otherwise specified.

Capable Luminaire This item is an A+ capable luminaire, which has been designed and tested to provide consistent color appearance and out-of-the-box control compatibility with simple commissioning.

• All configurations of this luminaire meet the Acuity Brands’ specification for chromatic consistency

• This luminaire is part of an A+ Certified solution for nLight® control networks when ordered with drivers marked by a shaded background*

• This luminaire is part of an A+ Certified solution for nLight control networks, providing advanced control functionality at the luminaire level, when selection includes driver and control options marked by a shaded background*

To learn more about A+, visit www.acuitybrands.com/aplus.

*See ordering tree for details

Embed nLight controls today. Prepare for tomorrow.

Static

Air Supply/Return

User-friendly install Scalability

Enhanced energy savings Space configuration

Code compliance Future-ready

Now Tomorrow

Ribbed Reflector Option

ADP Diffuser Option

Ordering Tree

DIGITAL NAVIGATION

nLight Platform Sensor Switch JOT Photometrics Performance Data http://www.designlights.org/QPL http://www.acuitybrands.com/resources/terms-and-conditions http://www.acuitybrands.com/aplus

2BLT Volumetric Recessed Lighting 2'x2'

BLT-2X2

COMMERCIAL INDOOR: One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) www.lithonia.com © 2015-2020 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/12/20

ORDERING INFORMATION Lead times will vary depending on options selected. Consult with your sales representative. Example: 2BLT2 33L ADP EZ1 LP835

2BLT2

Series Fixture Style Air function Lumens ‡ Diffuser Voltage Driver Color temperature

2BLT2 2X2 BLT (blank) Smooth Reflector

RB Ribbed Reflector

(blank) Static A Air supply/ return ‡

Standard efficiency ‡

(>125 LPW)

20L 2000 33L 3300 40L 4000 48L 4800

High efficiency ‡

(>130 LPW)

20LHE 2000

33LHE 3300

40LHE 4000

48LHE 4800

ADP Curved, ribbed ADSM Curved, smooth SDP Square, ribbed SDSM Square, smooth Includes trim rings to match sensored version ADPT Curved, ribbed ADSMT Curved, smooth SDPT Square, ribbed SDSMT Square, smooth

(blank) MVOLT 120 120V 277 277V 347 347V ‡

EZ1 eldoLED dims to 1% (0-10 volt dimming)

GZ1 Dims to 1% (0-10V dimming) 8

GZ10 Dims to 10% (0-10V dimming) ‡

SLD Step-level dimming ‡

LP830 82CRI, 3000 K

LP835 82CRI, 3500 K

LP840 82CRI, 4000 K

LP850 82CRI, 5000 K

LP930 90CRI, 3000K

LP935 90CRI, 3500K

LP940 90CRI, 4000K

LP950 90CRI, 5000K

A+ Capable options indicated by this color background.

nLight Interface Control ‡ nLight Wired (blank) no nLight ® interface N80 nLight with 80% lumen management N80EMG nLight with 80% lumen management

For use with generator supply EM power ‡ N100 nLight without lumen management N100EMG nLight without lumen management

For use with generator supply EM power ‡ nLight Wireless (blank) no nLight ® interface NLTAIR2 nLight AIR Generation 2 enabled ‡ nLight Wired (blank) No sensor control NES7 nLight™ nES 7 PIR integral occupancy sensor ‡ NESPDT7 nLight™ nES PDT 7 dual technology integral occupancy control ‡ NES7ADCX nLight™ nES 7 ADCX PIR integral occupancy sensor with automatic dimming photocell ‡ NESPDT7ADCX nLight™ nES PDT 7 dual technology integral occupancy sensor with automatic dimming photocell ‡ nLight Wireless

RES7 nLight AIR PIR integral occupancy sensor with automatic dimming photocell for Networking Capabilities

RES7PDT nLight AIR microphonics dual technology occupancy sensor with automatic dimming photocell

RIO nLight AIR radio module without sensor RES7EM nLight AIR PIR integral occupancy sensor with automatic dimming photocell and UL924 Emergency Operation, via power interrupt detection ‡

RES7PDTEM nLight AIR microphonics dual technology occupancy sensor with automatic dimming photocell and UL924 Emergency Operation, via power interrupt detection ‡

RIOEM nLight AIR radio module less sensor, with UL924 Emergency Operation, via power interrupt detection ‡

Individual Control MSD7ADCX PIR integral occupancy sensor with automatic dimming control photocell ‡ MSDPDT7ADCX PDT integral occupancy sensor with automatic dimming control photocell ‡ JOT Wireless room control with

“Just One Touch” pairing ‡ JOTVTX15 Wireless occupancy sensor with

“Just One Touch” pairing ‡

Standy Mode Options

NOC NOC Occupancy sensor disabled ‡

EL7L 700 lumen battery pack (Noncompliant with CA T20) ‡

EL14L 1400 lumen battery pack (Noncompliant with CA T20) ‡

EL14LSD 1400 lumen battery pack with self-diagnostic testing feature (Noncompliant with CA T20) ‡

E10WLCP EM Self-Diagnostic battery pack, 10W Constant Power, Certified in CA Title 20 MAEDBS ‡

CP Chicago plenum ‡ BGTD Bodine Generator Transfer Device ‡ PWS1836 6’ pre-wire, 3/8” diameter, 18 gauge, 1 circuit PWS1846 6’ pre-wire, 3/8” diameter, 18 gauge, 2 circuit PWS1846 PWSLV Two cables: one 6' pre-wire, 3/8” diameter, 18 gauge, 2 circuits; one 6' pre-wire, 3/8” diameter, 18 gauge, purple and gray ‡

PWS1856LV 6’ pre-wire, 3/8” diameter, 18 gauge, 1 circuit w/low voltage purple and grey wires ‡

GLR Fast-blowing fuse ‡ GMF Slow-blowing fuse ‡ NPLT Narrow pallet RRL_ RELOC®-ready luminaire ‡ LATC Earthquake clip DWAM Anti-Microbial paint JP28 Job packaging ‡ JP36 Job packaging IP5X Gasketed diffuser compartment to meet IP5X rating ‡

NOTE: ‡ indicates option value has ordering restrictions. Please reference the Option Value Ordering Restictions chart on the next page. Options are sorted alphanumerically.

http://www.lithonia.com

COMMERCIAL INDOOR: One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) www.lithonia.com © 2015-2020 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/12/20

‡ Option Value Ordering Restrictions

Option value Restriction 347 Not available with SLD, EL7L, EL14L, or E10WLCP options.

A Consult factory for airflow data BGTD Not available with JOT, JOTVTX15 sensor options or emergency battery options. Must specify voltage. Requires BSE labeling, voltage specific. Consult factory for options. Example: BGTD BSE10.

Control Must specify diffuser with trim rings.

CP Not available with N80, N80EMG, N100, or N100EMG.

GZ1, GZ10 Not available with any Control or Sensor options except JOT & JOTVTX15 EL7L, EL14L, EL14LSD, E10WLCP Not available with TD. When using pre-wire option, use PWS1846 or PWS1846 PWSLV. For more information on the EL14LSD, please see the

PSSD2 specification sheet.

GLR, GMF Must specify voltage. 120 or 277, with GLR and GMF fusing.

IP5X Not available with air supply/return or Wired Networking (NES_) and Individual Control (MSD_) sensors.

JOT, JOTVTX15 Not available with SLD, nLight, NLTAIR2, NOC, or BGTD options.

JP28 Only available with options: NES7, NESPDT7, NES7ADCX, NESPDT7ADCX, MSD7ADCX, MSDPDT7ADCX, RES7, RES7PDT, RIO.

Lumens Approximate lumen output. For high Efficiency, all versions may not achieve 130+ LPW. Refer to photometry on www.acuitybrands.com. Air supply/return option, 90

CRI, and versions with integral sensor trim rings may not achieve 130 LPW.

MSD7ADCX, MSDPDT7ADCX Only available with EZ1 driver option. 0-10v dimming wires not accessible via access plate.

NES7, NESPDT7, NES7ADCX, NESPDT7ADCX Requires N80, N80EMG, N100, or N100EMG. Only available with EZ1 driver.

NLTAIR2 Must order with nLight Wireless option from Control section. Only available with EZ1 driver.

NOC Can only be ordered in conjunction with EZ1, NLTAIR2, RES7/RES7PDT. Occupancy sensor disabled at factory but can be re-enabled upon commissioning.

N80EMG, N100EMG nLight EMG option requires a connection to existing nLight network. Power is provided from a separate N80 or N100 enabled fixture.

PWS1846 PWSLV, PWS1856LV Not available with nLIGHT wired network or individual controls RES7EM, RES7PDTEM, RIOEM See UL924 Sequence of Operation chart on page 3.

RRL_ For ordering logic consult: RRL_2013.

SLD Not available with with any nLight Interface or Control options.

Stock/MTO Catalog Description * UPC Lumens Wattage LPW Color Temperature Voltage Pallet Qty Stock 2BLT2 33L ADP LP835 190887529708 3332 26.67 124.92 3500K/82 CRI 120-277 56

2BLT2 33L ADP LP840 190887529739 3385 26.67 126.91 4000K/82CRI 120-277 56

2BLT2 33L ADP EL14L LP835 190887529890 3332 26.67 124.92 3500K/82CRI 120-277 56

2BLT2 33L ADP EL14L LP840 190887529937 3385 26.67 126.91 4000K/82CRI 120-277 56

*Generic 0-10V Dimming to 10%.

Non-Configurable BLT

MOUNTING DATA

Ceiling Type Appropriate Trim Type

Exposed grid tee (1’ and 9/16”) G

Concealed grid tee G

Plaster or plasterboard G*

*DGA accessory available to provide ceiling trim flange and fixture support for plaster or plasterboard ceiling. Recommended rough-in dimensions for DGA installation is 24-3/4" x 24-3/4" (Tolerance is +1/8", -0”).

9/16 Screw Slot15/16

Multiple Diffuser Options

Square Ribbed Square SmoothCurved Ribbed

ADP ADSM SDP SDSM

Curved Smooth

UL924 Sequence of Operation

For 90 minutes following any complete AC power interruption >200 ms:

• Digital dimming is commanded to high end trim level.

• Device ignores wireless lighting control commands.

SDSM Diffuser Option http://www.lithonia.com https://img.acuitybrands.com/public-assets/catalog/272933/pssd2.pdf?abl_version=04%2f05%2f2019+06:07:28&DOC_Type=SPEC_SHEET http://www.acuitybrandslighting.com/library/rw/documents/specsheets/rrl_2013.pdf

COMMERCIAL INDOOR: One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) www.lithonia.com © 2015-2020 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/12/20

Accessories: Order as separate catalog number.

DGA22 Drywall grid adapter for 2x2 recessed fixture 2X2SMKSHP PAF Surface Mount Troffer Kit Post Paint

Replacement Parts: Order as separate catalog number.

*247WJV 2DBLT24 ADP LENS ASSEMBLY 2 ft. replacement lens *249P2P 2DBLT24 SDP LENS ASSEMBLY 2 ft. replacement lens *249P2W 2DBLT24 ADSM LENS ASSEMBLY 2 ft. replacement lens *249P32 2DBLT24 SDSM LENS ASSEMBLY 2 ft. replacement lens *237LT1 2DBLT24 ADPT LENS ASSEMBLY 2 ft. replacement lens *237LT3 2DBLT24 SDPT LENS ASSEMBLY 2 ft. replacement lens *237LT5 2DBLT24 ADSMT LENS ASSEMBLY 2 ft. replacement lens *237LT7 2DBLT24 SDSMT LENS ASSEMBLY 2 ft. replacement lens *237LT9 2DBLT24 ADPT SENSOR LENS ASSEMBLY 2 ft. replacement lens *237M4Y 2DBLT24 SDPT SENSOR LENS ASSEMBLY 2 ft. replacement lens *237M57 2DBLT24 ADSMT SENSOR LENS ASSEMBLY 2 ft. replacement lens *237M5H 2DBLT24 SDSMT SENSOR LENS ASSEMBLY 2 ft. replacement lens

Accessories & Replacement Parts

Sensor Switch JOT Enabled Wireless Solution

1. Power: Install JOT enabled fixtures and controls as instructed.

2. Pair: Insert the pairing tool into the pinhole on the wall switch; press and hold any button for 6 seconds.

3. Play: Once paired, each fixture will individually dim down to 10% brightness. All products will be fully functional.

BLT Series

Sensor Switch

WSXA JOT

Designed with contractors in mind, the Sensor Switch JOT enabled wireless solution offers a straightforward approach to the installation and pairing of lighting fixtures and controls. Absolutely no 0-10V control wires and no mobile apps are needed with JOT enabled products, allowing for lightning speed installation right out of the box.

BLT Series with integrated

JOT OCC

Sensors

Sensor Switch

SPODMRA JOT

JOT Wireless

COMMERCIAL INDOOR: One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) www.lithonia.com © 2015-2020 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/12/20

NH NH NH

BLT Series nLight Wired nPODMA

CAT5e

NH NH NH

BLT Series nLight AIR rPODBA Mobile Device nLight Platform nLight embedded fixtures offer: Customers get:

Manual Dimming Convenience and visual comfort for occupants

Motion Sensing and/or Daylight Harvesting Energy savings and code compliance

Fixture or Group Level Control Ability to configure lighting to the space requirements

Flexibility Ease of fixture moves, adds and changes

Wireless Wall Switch (nLight AIR Only) Ease and flexibility of placement

Astronomical and Time of Day Scheduling Energy savings and building security

Scalable Solution nLight controls to grow with your business

Future-Ready nLight platform to set foundation for future upgrades and capabilities

Simple as 1,2,3

1. Install the nLight® AIR fixtures with embedded smart sensor

2. Install the wireless battery-powered wall switch

3. With CLAIRITY app, pair the fixtures with the wall switch and if desired, customize the sensor settings for the desired outcome

Simple as 1,2,3

1. Install the nLight® Wired fixtures with embedded control

2. Install the nLight Wired wall switch

3. Connect the fixtures using standard CAT5e cables and the devices will automatically discover each other and work (plug and play) nLight Air Wireless nLight Wired Networking

COMMERCIAL INDOOR: One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) www.lithonia.com © 2015-2020 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/12/20

Sensor Options

Option Automatic Dimming Photocell

Occupancy Sensing nLight Wired Networking nLight AIR NetworkingPIR PDT

MSD7ADCX X X

MSDPDT7ADCX X X

NES7 X X

NES7ADCX X X X

NESPDT7 X X

NESPDT7ADCX X X X

RES7 X X X

RESPDT7 X X X X

Integrated Sensor with Individual Control The MSD7ADCX PIR occupancy sensor/automatic dimming photocell is ideal for areas without obstructions and where daylight harvesting may be desired. Suggested applications include, but not limited to, hallways, corridors, storage rooms, and breakrooms or other areas where people are typically moving.

The MSDPDT7ADCX PIR/Microphonics Dual Tech occupancy sensor/automatic dimming photocell is ideal for areas with obstructions and where daylight harvesting is desired. Suggested applications include, but not limited to, open offices, private offices, classrooms, public restrooms, and conference rooms.

Sequence of Operation (nES7 and rES7 and Sensor)

MIN

LIG

HT

LE

VE

L

MAX

7.5 MIN

TIME DELAY

2.5 MIN AT

A 1% LEVEL

LIGHTS OFF LIGHTS ONLIGHTS ON

Room Unoccupied

Occupants Detected In The Space

Sensor Detects Motion

MOTION NO MOTION MOTION

SEQUENCE OF OPERATION

5.5 18

4.6 15

3.7 12

2.7 9

1.8 6

0.9 3 0 m 0 ft

0.9 3

1.8 6

2.7 9

3.7 12

4.6 15

5.5 18

9 FT Mounting

• Recommended for walking motion detection from mounting heights between 8 ft (2.44 m) and 20 ft (6.10 m)

• Initial detection of walking motion along sensor axes at distances of 2x the mounting height up to 15 ft (4.57 m) and

• 1.75x up to 20 ft (6.10 m).

• Provides 12 ft (3.66 m) radial detection of small motion when mounted at 9 ft (2.74 m)

• Initial detection will occur earlier when walking across sensor’s field of view than when walking directly at sensor

Sensor Coverage Pattern Mini 360° Lens

*The presetting on the automatic dimming photocell is 5fc (NES7) and 10fc (RES7).

Sequence of Operation (MSD7 Sensor)

MIN

LIG

HT

LE

VE

L

MAX

17.5 MIN

TIME DELAY

2.5 MIN AT

A 1% LEVEL

LIGHTS OFF LIGHTS ONLIGHTS ON

Room Unoccupied

Occupants Detected In The Space

Sensor Detects Motion

MOTION NO MOTION MOTION

SEQUENCE OF OPERATION

*The presetting on the automatic dimming photocell is 5fc.

nLight AIR Wireless nLight AIR is the ideal solution for retrofit or new construction spaces where adding additional wiring can be labor intensive and nLight AIR is available with or without an integral sensor. The integrated rES7 or rES7PDT smart sensors are part of each luminaire in the nLight AIR network, which can be grouped to control multiple luminaires. The granularity of control with the digital PIR occupancy detection and daylight sensing makes a great solution for any application.

nLight Wired Networking The nES 7 is ideal for small rooms without obstructions or areas with primarily walking motion.

Ideal areas include hallways, corridors, storage rooms, and breakrooms. Additionally, the nES7ADCX includes an integrated photocell, which enables daylight harvesting controls.

For areas like restrooms, private offices, open offices, conference rooms or any space with obstructions, the nES PDT 7 dual technology sensor is recommended. The nES PDT 7 utilizes both PIR (passive infrared) and Microphonics technologies to detect occupancy. Additionally, the nESPDT7ADCX includes an integrated photocell, which enables daylight harvesting controls which is ideal for areas where windows are present.

COMMERCIAL INDOOR: One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) www.lithonia.com © 2015-2020 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/12/20 nLight® Wired Control Accessories:

Order as separate catalog number. Visit www.acuitybrands.com/products/controls/nlight.

WallPod stations Model number Occupancy sensors Model number On/Off nPODMA [Color] Small motion 360°, ceiling (PIR / dual tech) nCM 9 RJB / nCM PDT 9 RJB On/Off & raise/lower nPODMA DX [Color] Large motion 360°, ceiling (PIR / dual tech) nCM10 RJB / nCM PDT 10 RJB Graphic touchscreen nPOD TOUCH [Color] Wall switch with raise/lower nWSX PDT LV DX [color] Photocell controls Model number Cat-5 cable (plenum rated) Model number Full range dimming nCM ADCX RJB 10' cable CAT5 10FT J1

30' cable CAT5 30FT J1 nLight® AIR Control Accessories:

Order as separate catalog number. Visit www.acuitybrands.com/products/ controls/nlightair.

Wall switches Model number On/Off single pole rPODBA [color] G2 On/Off two pole rPODB A2P [color] G2 On/Off & raise/lower single pole rPODBA DX [color] G2 On/Off & raise/lower two pole rPODBA 2P DX [color] G2

RCMS

Notes 1 RCMS requires low voltage power from either RPP20 DS 24V G2 or PS150.

rCMS1 Example: RCMS PDT 10 AR G2

Series / Detection Power Supply1 Occupancy Detection Lens (Required) Operating Mode Generation

RCMS nLight AIR occupancy and daylight sensor

[blank] Power Supply ordered separately

PS 150 Standard 150 mA Power Supply

[blank] PIR Detection PDT Dual Tech PIR/

Microphonics

10 Large Motion/ Extended Range 360°

9 Small Motion/ Extended Range 360°

6 High Bay 360° Lens

[BLANK] None AR Auxiliary

Relay

G2 Generation 2 compatibility

Controls Accessories

Sensor Switch

WSX

nLight WIRED nPODMA DX nLight AIR rPODBA rPODBA

Winning in Small OffiesWinning in Small Offies

BLT fixtures with integrated rIO devices complement any small office space. Pair them with an rCMS occupancy sensor and the space now has wireless occupancy sensing and dimming capability. For additional configuration options please consult with Tech Support.

BLT with rIOnLight WIRED

NPOD UNITOUCH

http://www.lithonia.com http://www.acuitybrands.com/products/controls/nlight http://www.acuitybrands.com/products/controls/nlightair http://www.acuitybrands.com/products/controls/nlightair https://www.acuitybrands.com/products/detail/708905/sensor-switch/wsx-series/wall-switch-sensor https://www.acuitybrands.com/products/detail/708905/sensor-switch/wsx-series/wall-switch-sensor https://www.acuitybrands.com/products/detail/982001/nlight/npodma-family/nlightr-wired-wall-switch https://www.acuitybrands.com/products/detail/982001/nlight/npodma-family/nlightr-wired-wall-switch https://www.acuitybrands.com/products/detail/982003/nlight/rpodba-family/nlightr-air-wall-switch https://www.acuitybrands.com/products/detail/982003/nlight/rpodba-family/nlightr-air-wall-switch https://www.acuitybrands.com/products/detail/981468/nlight/nlightr-unitouch/touchscreen-wall-switch https://www.acuitybrands.com/products/detail/981468/nlight/nlightr-unitouch/touchscreen-wall-switch

COMMERCIAL INDOOR: One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) www.lithonia.com © 2015-2020 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/12/20

PHOTOMETRICS

2BLT2 33L ADP LP835, 3332 delivered lumens, test no. ISF36900P19, tested in accordance to IESNA LM-79

2BLT2 40L ADP LP835, 4041 delivered lumens, test no. ISF36900P35, tested in accordance to IESNA LM-79

0° 20°

40°

60°

80°

90°

0°0°0° 90°

180°

Coefficients of Utilization pf 20% pc 80% 70% 50% pw 70%50%30% 50%30%10% 50%30%10%

R C

R

Zonal Lumen Summary

Zone Lumens % Lamp % Fixture

0° - 30°

0° - 40°

0° - 60°

0° - 90°

90° - 120°

90° - 130°

90° - 150°

90° - 180°

0° - 180°

25.6

41.7

74.0

100.0

0.0

0.0

0.0

0.0

100.0

25.6

41.7

74.0

100.0

0.0

0.0

0.0

0.0

100.0

CP Summary

0° 90

0°

5°

15°

25°

35°

45°

55°

65°

75°

85°

0° 20°

40°

60°

80°

90°

0°0°0° 90°

180°

Coefficients of Utilization pf 20% pc 80% 70% 50% pw 70%50%30% 50%30%10% 50%30%10%

R C

R

Zonal Lumen Summary

Zone Lumens % Lamp % Fixture

0° - 30°

0° - 40°

0° - 60°

0° - 90°

90° - 120°

90° - 130°

90° - 150°

90° - 180°

0° - 180°

25.6

41.7

74.0

100.0

0.0

0.0

0.0

0.0

100.0

25.6

41.7

74.0

100.0

0.0

0.0

0.0

0.0

100.0

CP Summary

0° 90

0°

5°

15°

25°

35°

45°

55°

65°

75°

85°

Enabled by the embedded nLight control, the BLT actively tracks its run-time and manages its light source such that constant lumen output is maintained over the system life. Referred to as lumen management, this feature eliminates the energy waste created by the traditional practice of over-lighting.

0 10 20 30 40 50

THOUSAND OPERATING HOURS

0 10 20 30 40 50

THOUSAND OPERATING HOURS

POWER INPUT

LIGHT

OUTPUT

100%

80%

100%

80%

30W

24W

30W

24W

LI

G

H T

O U

TP

U

T

LI

G

H T

O U

TP

U

T

PO

W

ER

IN

PU

ER

IN

PU

T

Without Lumen Management Energy is wasted and light level is inconsistent.

POWER

INPUT

LIGHT OUTPUT

With Lumen Management Energy is saved and light level remains consistent.

Wasted Energy

Saved Energy

0 10 20 30 40 50

THOUSAND OPERATING HOURS

0 10 20 30 40 50

THOUSAND OPERATING HOURS

POWER INPUT

LIGHT

OUTPUT

100%

80%

100%

80%

30W

24W

30W

24W

LI

G

H T

O U

TP

U

T

LI

G

H T

O U

TP

U

ER

IN

PU

ER

IN

PU

T

Without Lumen Management Energy is wasted and light level is inconsistent.

POWER

INPUT

LIGHT OUTPUT

With Lumen Management Energy is saved and light level remains consistent.

Wasted Energy

Saved Energy

Constant Lumen Management

COMMERCIAL INDOOR: One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) www.lithonia.com © 2015-2020 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/12/20

Performance Data Model Number Lumens LPW Watts DLC Listing DLC ID 2BLT2 20L ADP EZ1 (GZ1, GZ10) LP840 [All Options] 2065.45 124.06 16.64 Premium PM92196A

2BLT2 20L ADP EZ1 (GZ10) LP835 [All Options] 2033 126.58 16.06 Premium P6445UVD

2BLT2 20L ADP GZ1 LP835 [All Options] 2033 122.11 16.64 standard PLNK6MX8

2BLT2 20L ADPT EZ1 (GZ10) LP840 [All Options] 2037.91 126.89 16.06 Premium PYX15QEQ

2BLT2 20L ADPT GZ1 LP835 [All Options] 2005.89 120.49 16.64 standard P40HQGLB

2BLT2 20L ADPT GZ1 LP840 [All Options] 2037.91 122.41 16.64 standard PB3HB9AK

2BLT2 33L ADP EZ1 (GZ1, GZ10) LP835 [All Options] 3332 124.92 26.67 Premium PHSXHE8F

2BLT2 33L ADP EZ1 (GZ1, GZ10) LP840 [All Options] 3385.19 126.91 26.67 Premium PD18CKQ8

2BLT2 33L ADPT EZ1 (GZ1, GZ10) LP840 [All Options] 3340.05 125.22 26.67 Premium PF98CZ2H

2BLT2 33L ADPT EZ1 (GZ10) LP835 [All Options] 3287.57 125.14 26.27 Premium PTKZR9WQ

2BLT2 33L ADPT GZ1 LP835 [All Options] 3287.57 123.25 26.67 standard PTN5023N

2BLT2 40L ADP EZ1 (GZ1, GZ10) LP835 [All Options] 4041 127.35 31.73 Premium P1XWW9GV

2BLT2 40L ADP EZ1 (GZ1, GZ10) LP840 [All Options] 4105.51 129.38 31.73 Premium PHCQ2CQF

2BLT2 40L ADPT EZ1 (GZ1, GZ10) LP835 [All Options] 3987.12 125.65 31.73 Premium PW6RMMJ4

2BLT2 40L ADPT EZ1 (GZ1, GZ10) LP840 [All Options] 4050.77 127.65 31.73 Premium P5YYDAA8

2BLT2 48L ADP EZ1 (GZ1, GZ10) LP835 [All Options] 4800 109.9 43.67 standard PJRH1R1G

2BLT2 48L ADP EZ1 (GZ1, GZ10) LP840 [All Options] 4876.63 111.66 43.67 standard P8G93YOK

2BLT2 48L ADPT EZ1 (GZ1, GZ10) LP835 [All Options] 4736 108.44 43.67 standard PITU3V6X

2BLT2 48L ADPT EZ1 (GZ1, GZ10) LP840 [All Options] 4811.61 110.17 43.67 standard P5X2XU76

HE Performance Data Model Number Lumens LPW Watts DLC Listing DLC ID 2BLT2 20LHE ADP EZ1 (GZ1, GZ10) LP835 [All Options] 1948 130.59 14.91 Premium PUQCZNQI

2BLT2 20LHE ADP EZ1 (GZ1, GZ10) LP840 [All Options] 1979.1 132.67 14.91 Premium PJCZRW21

2BLT2 20LHE ADPT EZ1 (GZ1, GZ10) LP840 [All Options] 1952.71 130.9 14.91 Premium PLC4RF4L

2BLT2 33LHE ADP EZ1 (GZ1, GZ10) LP835 [All Options] 3392 137.3 24.7 Premium PXXZN9PH

2BLT2 33LHE ADP EZ1 (GZ1, GZ10) LP840 [All Options] 3446.15 139.5 24.7 Premium PKPJYYRF

2BLT2 33LHE ADPT EZ1 (GZ1, GZ10) LP835 [All Options] 3346.77 135.47 24.7 Premium PZC8BZSS

2BLT2 33LHE ADPT EZ1 (GZ1, GZ10) LP840 [All Options] 3400.2 137.64 24.7 Premium PM5G8AFU

2BLT2 40LHE ADP EZ1 (GZ1, GZ10) LP835 [All Options] 4118 133.71 30.79 Premium PJ55XFFP

2BLT2 40LHE ADP EZ1 (GZ1, GZ10) LP840 [All Options] 4183.74 135.85 30.79 Premium PEGFHPZD

2BLT2 40LHE ADPT EZ1 (GZ1, GZ10) LP835 [All Options] 4063.09 131.93 30.79 Premium P8E16E9B

2BLT2 40LHE ADPT EZ1 (GZ1, GZ10) LP840 [All Options] 4127.96 134.04 30.79 Premium PFRSSSVG

2BLT2 48LHE ADP EZ1 (GZ1, GZ10) LP835 [All Options] 4845 128 37.85 Premium P558XUZP

2BLT2 48LHE ADP EZ1 (GZ1, GZ10) LP840 [All Options] 4922.35 130.04 37.85 Premium P1863H56

2BLT2 48LHE ADPT EZ1 (GZ1, GZ10) LP835 [All Options] 4780.4 126.29 37.85 Premium PHPTG5M8

2BLT2 48LHE ADPT EZ1 (GZ1, GZ10) LP840 [All Options] 4856.71 128.31 37.85 Premium PBKN954Z

DLC information is subject to change, for the most up-to-date information please refer to www.dlc.org. Above listings do not cover 347v or SLD.

DLC information is subject to change, for the most up-to-date information please refer to www.dlc.org. Above listings do not cover 347v or SLD.

How to Estimate Delivered Lumens in Emergency Mode Use the formula below to estimate the delivered lumens in emergency mode Delivered Lumens = 1.25 x P x LPW P = Ouput power of emergency driver. P = 10W for E10WLCP option.

LPW = Lumen per watt rating of the luminaire. This information is available on the ABL luminaire spec sheet. LPW = Lumen per watt rating of the luminaire. LPW information available in Performance Data section.

LDN6

6" Open and WallWash LED

Non-IC New Construction Downlight

ORDERING INFORMATION Example: LDN6 35/15 LO6AR LSS MVOLT EZ10

DOWNLIGHTING LDN6

Lead times will vary depending on options selected. Consult with your sales representative.

Accessories: Order as separate catalog number.

PS1055CP FMC Power Sentry batterypack, T20 compliant, field installable, 10w constant power

EAC ISSM 375 Compact interruptible emergency AC power system EAC ISSM 125 Compact interruptible emergency AC power system GRA68 JZ Oversized trim ring with 8" outside diameter SCA6 Sloped Ceiling Adapter. Degree of slope must be specified

(5D, 10D, 15D, 20D, 25D, 30D). Ex: SCA6 10D.

Notes 1 Overall height varies based on lumen package; refer to dimensional chart on page 3.

2 Not available with finishes.

3 Not available with emergency options.

4 Must specify voltage 120V or 277V.

5 Available with clear (AR) reflector only.

6 12.5" of plenum depth or top access required for battery pack maintenance.

7 Specify voltage. ER for use with generator supply EM power. Will require an emergency hot feed and normal hot feed.

8 Fixture begins at 80% light level. Must be specified with NPS80EZ or

NPS80EZ ER. Only available with EZ10 and EZ1 drivers.

9 Not available with CP, NPS80EZ, NPS80EZER, NPP16D, NPP16DER or N80 options.

10 NLTAIR2, NLTAIRER2 and NLTAIREM2 not recommended for metal ceiling installations.

11 Fixture height is 6.5" for all lumen packages with HAO.

12 Must specify voltage for 3000lm and above. 5000lm with marked spacing

24 L x 24 W x 14 H. Not available with emergency battery pack option.

13 Must specify D10 or D1 driver. Not available with nLight options. Not avail-able with CP. Not recommended for metal ceiling installation. Not for use with emergency backup power systems other than battery packs.

14 When combined with EZ1 or EZ10 drivers, can be used as a normal power sensing device for nLight AIR devices and lumiaires with EM options.

Catalog Number

Notes

Type

LDN6

Series Color temperature Lumens1 Aperture/Trim Color Finish Voltage

LDN6 6" round 27/ 2700K 30/ 3000K 35/ 3500K 40/ 4000K 50/ 5000K