Attachment 4- Existing Product Data Sheets.pdf

SurTrac® Aluminum Cantilever Gate System

MasterHalco.com | 888-643-3623

Strong Reliable Safe

Customizable

• Specifications

• CAD Drawings

• Modular Assembly

• Automated or Manual Driven

• Technical Assistance

Performance by Design

1 Highest Yield Strength Top Track

– Certified 6061-T6 Structural Aluminum This One Piece Extrusion is made of Certified 6061-T6 Structural Aluminum and does not require stitch welding which can affect the Top Track tensile strength. The SurTrac top track is 58% heavier and 40% stronger than competitors comparable top track. This high strength material allows us to build a gate that will stand up to the most severe commercial & industrial duty cycling.

2 Truck Assemblies

– Tight bearing tolerances & high quality, equal smooth gate operation Heavy-duty body, stainless steel truck wheels 1/2” wide with 2” diameter industrial sealed bearings - 4 for vertical load bearing and 2 for horizontal stabilization. 5/8” stainless steel shoulder bolt is self aligning with nylock nut assembled onto a heavy duty steel Truck Bracket for a secure positive alignment of trucks in gate track, whether single or dual.

3 Bottom Rollers

– Easy installation and adjustability Easy installation of an adjustable yoke bracket with two rollers, provides positive alignment for lower gate frame as gate cycles during usage.

4 Structural Corner Gussets

– Increased Frame Strength and Rigidity Heavy Duty 1/4” aluminum gussets add frame strength & rigidity

5 Turn-Buckle Truss Adjustment

– Infinite Adjustability for Perfect Gate Cycling The 3/8” x 6” long turnbuckles are designed to be “In-Line” with the Truss cable. The turnbuckle design is infinitely adjustable and each turn produces a level of fine adjustment not possible in truss rods adjustments that are 45 degrees to the gate frame.

4 5 7

8 9

Single Track

Single Gate For openings up to 30 ft. wide

Dual Track

Single Gate For openings 30-50 ft. wide

No box frame required for gates up to 50 ft.

6 Aircraft Cable Truss System

– Shock-Absorbing and Low Maintenance 1/4” galvanized 7,000 pound Break Strength truss cables take SurTrac Gates to a whole new level of maintenance free life cycling! They are resilient and able to absorb the constant shock of hard openings and closings. The new SurTrac design provides dual, diagonally opposing Truss cables for ultimate weight control and operational fine tuning.

7 Hook Bolts

– Increased Security — Tamper proff fabric attachment 5/16” high strength aluminum L shape hook bolt inserted into vertical and horizontal uprights, then eye is closed around tension rods in each gate bay securing the chain link fabric with an attachment system that is uniform in appearance and provides longevity.

8 Simple Counterbalance Splice

– Bolted Splice Plate, No fabric Installation Required All SurTrac gates are UL 325 compliant with fabric installed in the counter balance (C/B). No wasted labor installing fabric in the field!

9 +1 Barb Arm Kit

– Easy installation for added security Kit includes barb arm, bolts, barbwire. +1 Barb Arm is constructed of 2” square aluminum with cap is bolted to top of gate frame. For ease of shipment, +1 Barb Arm kits can be added in the field or installed at time of manufacture.

10 Hardware Kit

– Complete hardware components Kit includes Bottom guide rollers with yokes, truck brackets with yokes, truck assemblies, Receivers for manual or electric operation.

30’ – 50’ Single Frame Design

– No Bulky Expensive Double Box Frame Needed One of the outstanding features of cantilever gates is that they require less space to operate.

SurTrac® Aluminum Cantilever Gate Systems

MasterHalco.com | 888-643-3623

MH 008981 © 09/12

Available from:

Year Limited Warranty:

The SurTrac Cantilever Gate Systems is condition-ally guaranteed for 5 years. For a copy the warranty, please visit www.masterhalco.com or contact your nearest Master Halco distribution center.

Drawings and Specs:

Drawings and specifications are available at www.masterhalco.com

Custom Engineering available upon request.

Accessories:

Hardware Kits (All gates are sold without hardware.

Hardware Kits ordered separately)

B05737 Electric operation using 4” OD post

B05739 Manual operation for 4” OD post

Kit Contents Bottom guide rollers with yokes, truck brackets with yokes, truck assemblies, Receivers for manual or electric operation.

On electronically operated gates when a Miller Edge sensor is used on the end of the gate for obstacle sensing protection; an additional post is used in place of a receiver kit

Barbed Wire Kits (All Gates are Barbed Wire Ready and will accept Barbed Wire Kits)

P/N are determined by the number of bays:

701278 Barb arm assembly for 4 bay gate – 20’ or 24’ opening

701276 Barb arm assembly for 5 bay gate – 30’ opening

Kit Contents Upright barb arms, barb wire, nuts and bolts to attach the upright barb arm and barb wire

Product Offering:

Standard Sizes Length: 10’-50’ Height: 6’, 7’, 8’

Barbed Wire: Yes These gates are designed to accept our Barbed Wire Kits. (See Below)

Hardware: Yes Hardware is sold separately as a Kit (See Below)

Gate Finishes: Yes Brushed Aluminum is the standard finish, but Black is available as well. Other colors available as special order

Reversible Design:

Reversible Gate Sizes 20’, 24’, 30’

Configuration: Gate comes in 2 halves; equaling the length of opening + counterbalance, allowing gate to slide either left or right.

Barbed Wire: Yes The gate is ready to accept the Barbed Wire Kit.

Need to stock these gates but don’t know which way they will need to slide… Try our “Reversible” design

Also available:

• Gate Operators

• Chain Link Fence systems

Please visit www.masterhalco.com or contact your nearest Master Halco distribution center.

MANUAL OR OPERATED SURTRAC® ALUMINUM CANTILEVER SLIDE GATES

SECTION 32 31 00

MANUAL OR OPERATED SURTRAC® ALUMINUM CANTILEVER SLIDE GATES

PART 1 GENERAL

1.01 SECTION INCLUDES

A. Chain link cantilever slide gates with enclosed aluminum track and hardware manufactured to comply with ASTM F-1184.

1.02 RELATED SECTIONS

A. Section 32 31 13 Chain Link Fences and Gates B. Section 32 31 13.53 High-Security Chain Link Fences and Gates C. Section 32 10 00 Paving and Surfacing D. Section 03 30 00 Cast-In-Place Concrete E. Section 04 20 00 Unit Masonry

1.03 SUBMITTALS

A. Changes in specifications may not be made after the bid date.

B. Shop drawings: Layout of fences and gates with dimensions, details, and finishes of components, accessories, and post foundations.

C. Product Data: Manufacturer’s catalog cuts indicating material compliance and specified options.

D. Samples: Samples of materials (e.g. fabric, wires, and accessories).

1.04 SPECIAL WARRANTY

A. Provide manufacturer’s standard limited warranty covering cantilever slide gate and truck assembly against failure resulting from normal use for a period of 5 years from date of purchase. Failure is defined as any defect in manufacturing that prevents the gate from operating in a normal manner.

PART 2 PRODUCTS

2.01 MANUFACTURER

A. Products from qualified manufacturers having a minimum of 5 years experience manufacturing internal roller cantilever slide gate will be acceptable by the architect as equal, if approved in writing, ten days prior to bidding, and if they meet all of the following specifications for design, size, gauge of metal parts and fabrication.

B. Obtain chain link fences and gates, including accessories, fittings, and fastenings from a single source.

C. Approved Manufacturer: SurTrac Aluminum Cantilever Slide Gate by Master Halco, Inc., Irving, TX Phone (888) 643-3623

2.02 MANUAL OR OPERATED CHAIN LINK CANTILEVER SLIDE GATES

A. Gate frames: Fabricate chain link cantilever slide gates in accordance with ASTM F-1184, Type II, Class 2, using aluminum mem-bers conforming to ASTM B 221, alloy and temper 6061-T6. Vertical members shall be 2 inch (50mm) square aluminum, weighing

1.13 lb./ft., 2 inch x 4 inch aluminum bottom frame member weighing 1.73 lb./ft., and a one-piece aluminum track/frame member weighing a minimum of 4.621 lb./ft. for Single Track and 7.95 lb./ft. for Dual Track. The 2 inch square frame member of said track/ frame shall have a wall thickness of not less than .250 inches on all four sides. Aluminum alloy used shall be 6061-T6 only. Internal uprights shall be 2-inch square aluminum spaced equally at no more than 6 feet on center subdividing the gate frame into panels.

Weld all members together forming a rigid one-piece frame integral with top track. Provide 2 truck assemblies for each gate leaf, except as indicated for gates larger than 30’ (9144mm). Frame sizes over 27’ (8230 mm) in length shall be shipped in 2 parts and field spliced with special attachments provided by the manufacturer.

Revised 3/20/2008

Gate Opening Cantilever Support (Overhang) Overall Panel Width 6 Foot 4 Foot 10 Foot 8 Foot 4 Foot 12 Foot 10 Foot 4 Foot 14 Foot 12 Foot 5 Foot 17 Foot 14 Foot 6 Foot 20 Foot 16 Foot 7 Foot 23 Foot 18 Foot 8 Foot 26 Foot 20 Foot 8 Foot 28 Foot 22 Foot 9 Foot 31 Foot 24 Foot 10 Foot 34 Foot 26 Foot 11 Foot 37 Foot 28 Foot 12 Foot 40 Foot 30 Foot 12 Foot 42 Foot spaquette Rectangle

MANUAL OR OPERATED SURTRAC® ALUMINUM CANTILEVER SLIDE GATES contd.

For gate leaf sizes 31’ (9449 mm) to 50’ (15,240 mm), a single extruded member forming a dual enclosed track/frame without welding shall be employed. An integral 2” x 4” dimensional top frame, with center stabilizing web, shall be integral to the aluminum track/frame profile all thicknesses to be 0.25” (6.35 mm). Dual top track/frame profile to weigh 7.95 lbs./ft.

Provide 2 truck assemblies for each track for each gate leaf, total 4 truck assemblies. Bottom rail shall consist of 2” x 4” (50mm x 100 mm) aluminum member weighing 1.73 lb./ft. (2.67 kg/m).

Gate Opening Cantilever Support (Overhang) Overall Panel Width 32 Foot 13 Foot 45 Foot 34 Foot 14 Foot 48 Foot 36 Foot 15 Foot 51 Foot 38 Foot 16 Foot 54 Foot 40 Foot 16 Foot 56 Foot 42 Foot 17 Foot 59 Foot 44 Foot 18 Foot 62 Foot 46 Foot 19 Foot 65 Foot 48 Foot 20 Foot 68 Foot 50 Foot 20 Foot 70 Foot B. Gate Frame Finish: Natural Aluminum Chain Link Filler Finish: To match specification of existing fence

* All Operated Chain-Link Cantilever slide gates will be filled across the entire length of the panel (including the back frame counterbalance) to satisfy UL325 and ASTM F-2200 safe gate design guidelines.

** Chain Link mesh size, and wire gauge to match that of existing fence. Fabric shall be attached between each internal upright with hook bolts spaced no more than 15 inches (380 mm) on center as recommended by the manufacturer.

C. Trussing: Each bay shall be cross-trussed by means of 1/4” cable with adjustable turnbuckles. Trusses will maintain the structural integrity of the gate while allowing for expansion and contraction of aluminum in varying weather conditions.

D. Top track/rail: Enclosed combination one-piece track and rail, aluminum extrusion with weight of:

-Openings up to 30’; 4.62 lbs./ft. Top track/rail to be a single formed profile with integrated center stabilizing web without welding.

All wall thicknesses to be 0.25”.

-Openings up to 31’ to 50’; 7.95 lbs./ft. Top track/rail to be a single formed profile with integrated center stabilizing web without welding. All wall thicknesses to be 0.25”.

E. Truck assembly: Swivel type, zinc die coated steel, with 6 sealed lubricant ball bearing rollers, 2 inches (50 mm) in diameter by 9/16” (14 mm) in width, and 2 side rolling wheels to ensure truck alignment in track. Mount trucks on post brackets using 7/8” (22

mm) diameter ball bolts with 5/8” (16 mm) shank. Truck assembly shall withstand same reaction load as track 2,000 # (907.2 kg.).

Revised 3/20/2008 F. Gate hangers, brackets, guide assemblies, receivers, and latches: Malleable iron or steel, galvanized after fabrication.

Operated cantilever gates are shipped without standard latching/locking hardware per ASTM F-2200. If positive locking is required, a suitable electronic locking device should be employed (See Section 02829 if applicable).

G. Bottom guide wheel assemblies: Each assembly shall consist of two, 3” (75 mm) diameter wheels, straddling bottom horizontal gate rail, allowing adjustment to maintain gate frame plumb and in proper alignment. Attach one assembly to each support post.

H. End Plug: After gate has been installed, both ends of the combination track/frame member shall be closed off with a shock absorbing plastic block that shall also serve as a stop bracket.

I. Gate posts:

For gates under 31’-0” (9449 mm): galvanized steel 4” (101.6 mm) OD schedule 40 pipe, ASTM F 1083, weighing 9.1 lb./ft. (13.6 kg/m). Provide 1 latch post and 2 support posts for single slide gates and 4 support posts for double slide gates.

For gates 31’-0” (9449 mm) or larger: 2 pairs of support posts for each leaf (dual) 4” (100 mm) OD schedule 40 pipe, ASTM F 1083, weighing 9.1 lb./ft. (13.6 kg/m) each. Posts connected by welding 6 inch x 3/8 inch (12.7 x 9.5 mm) plate between posts as shown on drawings. Also one 4” (100 mm) latch post.

1. Finish: to match fence.

2.03 SETTING MATERIALS

A. Concrete: Minimum 28 day compressive strength of 3,000 psi (20 MPa).

2.04 CERTIFICATIONS

A. American Welding Society AWS D1.2 Structural Welding Code.

B. All welds on the gate frame shall conform to Welding Procedure Specification and Procedure Qualification Record to insure conformance to the AWS D1.2 Structural Welding Code. All individual welders shall be certified to AWS D1.2 welding code.

MANUAL OR OPERATED SURTRAC® ALUMINUM CANTILEVER SLIDE GATES contd.

C. Gate manufacturer shall provide independent certification as to the use of a documented Welding Procedure Specification and Procedure Qualification Record to insure conformance to the AWS D1.2 welding code. Upon request, Individual Certificates of Welder Qualification documenting successful completion of the requirements of the AWS D1.2 code shall also be provided.

PART 3 EXECUTION

3.01 EXAMINATION

A. Verify areas to receive fencing are completed to final grades and elevations.

B. Verify areas to assure sufficient space to receive gate in open position (gate and overhang).

C. Ensure property lines and legal boundaries of work are clearly established.

3.02 MANUAL OR OPERATED CHAIN LINK CANTILEVER SLIDE GATE FRAMING INSTALLATION

A. Install gate posts in accordance with manufacturers’ instructions, and in accordance with ASTM F-567.

B. Install “Fall-over” posts per ASTM F-1184 and ASTM F-2200 (Section 4.2) to prevent fall of more than 45 degrees from the vertical plane if gate should disengage from mounting hardware.

C. Concrete set gate posts: Drill holes in firm, undisturbed or compacted soil. Holes shall have diameter 4 times greater than outside dimension of post with a minimum diameter of 12” (304 mm), and depths approximately 6” (152 mm) inches deeper than post bottom with a minimum depth of 42” (1066 mm) per ASTM F-567 (Section 5.13.1). Excavate deeper as required for adequate support in soft and loose soils, and for posts with heavy lateral loads. Set post bottom 42” (1066 mm) below surface when in firm, undisturbed soil. Place concrete around posts in a continuous pour, tamp for consolidation. Trowel finish around post and slope to direct water away from posts. Check each post for vertical and top alignment, and maintain in position during placement and finishing operations.

Revised 3/20/2008

3.03 MANUAL GATE INSTALLATION

A. Install gates plumb, level, and secure for full opening without interference. Gate movement shall not be initiated by gravity when in an automated gate operator is disengaged/disconnected per ASTM F-1184.

B. Attach hardware by means which will prevent unauthorized removal.

C. Adjust gate and hardware for smooth operation.

D. All gate installations to conform to all applicable federal, state, and local codes as well as: ASTM F-567 and ASTM F-1184.

3.04 OPERATED GATE INSTALLATION

A. Install gates plumb, level, and secure for full opening without interference. Gate movement shall not be initiated by gravity when an automated gate operator is disengaged / disconnected per ASTM F-2220 (Section 4.9) B. There shall be a maximum gap of 2 ¼” (57 mm) between the horizontal plane of the moving gate panel and any fixed obstacle (support posts, “fall-over” posts, hardware, pilaster, etc.) Except that said obstacle be more than 16” from the moving horizontal plane of the gate panel per ASTM F-2200 (Section 6.1.4.).

C. Gate Receiver Guides shall be recessed behind the leading edge of the receiver post or any other fixed object per ASTM F- 2200 (Section 6.1.6).

D. No device designed to provide activation for the automated gate operator is to be installed within 6’ of the horizontal plane of the gate panel per UL-325.

E. All Operated Chain-Link Cantilever slide gates are required to have Gate Warning Placards fully visible to the approach on both sides of the gate per UL-325.

F. Attached hardware by means which will prevent unauthorized removal.

G. Adjust hardware for smooth operation.

H. All operated gate installations to conform to all applicable federal, state, and local codes as well as: ASTM F-567, ASTM F- 1184, ASTM F-2200, and Underwriters Laboratory UL-325 safety standards.

3.05 CLEANING

A. Clean up debris and unused material and remove from site.

Operated gates are intended for use in controlling vehicular traffic ONLY and are not intended to be used by pedestrians, or to control pedestrian traffic. Always install a separate man gate for pedestrian use.

EMX Industries, Inc.

4564 Johnston Parkway, Cleveland, Ohio 44128

P. 800 426 9912 F. 216 518 9884

Sales Inquiries: salessupport@emxinc.com Technical Support: technical@emxinc.com www.emxinc.com

The IRB-MON provides a universal solution for entrapment protection. One photoeye covers the entire spectrum of possible requirements for monitored and non-monitored photoeyes, simplifying inventory management and product training.

The IRB-MON is an external entrapment protection device type B1, non-contact sensor for use with automatic gates and doors. The device is UL325-2018 compliant and suitable for use with both operators that require monitored entrapment protection and those that do not require monitored operation.

There are four monitoring interfaces:

1. Normally closed: Cycles power to the transmitter while monitoring the receiver contacts for proper operation

2. Two-wire pulsed (2 freq): Provides 300Hz “heartbeat” unobstructed, 0Hz obstructed over power supply lines

3. Two-wire pulsed (3 freq): Provides 300Hz “heartbeat” unobstructed, 2Hz obstructed and 0Hz failure over power supply lines

4. Resistive termination: Provides a 10k Ohm resistance when unobstructed

The long range and thru beam features combined with the installer mode switch settings provide a flexible solution to all external entrapment protection needs.

A robust, NEMA 4X enclosure provides the durability required for high-reliability entrapment protection applications. The lens-less design minimizes fogging and false triggering caused by small objects and allows for easy alignment.

IRB-MON

UNIVERSAL UL325-2018 THRU BEAM PHOTOEYEUNIVERSAL UL325-2018 THRU BEAM PHOTOEYE

IRB-MONIRB-MON

WARRANTY EMX INC. the product described herein for a period of 2 years under normal use and service from the date of sale to our customer. The product will be free from defects in material and workmanship. This warranty does not cover ordinary wear and tear, abuse, misuse, overloading, altered products, or damage caused by the purchaser from incorrect connections, or lightning damage. There is no warranty of merchantability. There are no warranties expressed, implied or any affirmation of fact or representation which extend beyond the description set forth herein. EMX Inc. sole responsibility and liability, and purchaser’s exclusive remedy shall be limited to the repair or replacement at EMX’s option of a part or parts not so conforming to the warranty.

In no event shall EMX Inc. be liable for damages of any nature, including incidental or consequential damages, including but, not limited to any damages resulting from non-conformity defect in material or workmanship. Rev 1.9 01/30/2020 up to 115 ft. (35m) 24o potentiometer Green LED Green LED 3 modes, relay output, pulsed (3 frequency), pulsed (2 frequency) Light on/dark on selection Form C contacts (NO, COM, NC) 10k Ohm across NO contact Thermal fuse >300mS (for use in configuration 0 Monitored) 6…35 VDC, 12...24VAC (configuration 0-relay only) 15mA (12VDC, includes TX and RX wired in parallel) 60mA (relay activated) -40oF...170oF (-40oC...77oC)

NEMA 4X

2.3” (57mm) x 2.6” (65mm) x 3.7” (94mm) TX - 0.35 lbs (159 g), RX 0.35 lbs (159 g) TX-2 terminal, RX-5 terminal

Operating Range Detection Angle

Sensitivity Adjustment Power Indicator Detect Indicator

Mode Selection Switch Relay Output Operation

Relay Output Resistive Termination

Power Protection Transmitter Power Cycle

Power Supply Current (config. 1 and 2)

Current (config. 0) Operating Temperature

Environmental Dimensions (L x W x H)

Weight Connections

Technical Data

Ordering Information

• IRB-MON Thru beam photoeye

• IRB-HD-SET Gold anodized aluminum hoods

• IRB-SH-SET Gray powder coated steel hoods

• IRB-SP Nylon liquid tight strain relief connector, set of 2

• IRB-S Nylon mounting screws with nuts, set of 2

• IRB-BR Steel “L” shaped mounting bracket, set of 2

• IRB-RX-SH Receiver sunshield

Competitive Advantage The major advantage of the IRB-MON is its flexibility. This photoeye covers the whole spectrum of UL situations.

• Monitored application per UL325-2018 as applied to overhead door and gate operators

• Non-monitored UL325 for gate operators prior to 2018 requirements

• Non-UL installation

Distributors and dealers need only one photoeye to cover all these applications.

IRB-BR IRB-RX-SHIRB-SP / IRB-SIRB-HD-SET / IRB-SH-SET

Model: ME120

P.O. Box 159 • West Grove, PA 19390 • 610-869-4422 • Fax: 610-869-4423 • 800-220-3343 6809 South Harl Avenue, Suite A • Tempe, AZ 85283 • 480-755-3565 • Fax: 480-755-3558 • 800-887-3343 www.milleredge.com

The ME120 profile is ideal for a wide variety of applications, from motorized doors and gates to industrial safeguarding on manufacturing equipment.

Applications include: along conveyor systems to detect operator reach in, below lifts to protect from pinch points, and on a wide variety of plant equipment where touch-sensitive detection is desired.

Applications

• Motorized Doors

• Lifts

• Conveyors

• Pinch Points

• Machine Guarding

• Elevator Doors

• Rolling Shutters

• Slide Gates

• Swing Gates

SensingEdge

TECHNICAL SPECIFICATIONS FUNCTIONAL BENEFITS

Touch-sensitive signalling• Easy to install• Mounts vertically or horizontally• UL 325 Recognized Component•

Color: Black or Yellow

Length: Per specification to +/- 1/4”

Lead Wire: SJTO, 18 gauge, 2’ length

Sensitivity: Nominal 8-13 lbf

Electrical Maximum: 24 volts AC/DC,1/2 amp

Contact Element: Alumaglas®

Materials: Flexible PVC

Mounting Channel: Rigid PVC or aluminum

Temperature Range: -30oF to +155oF

Wire Outlet Location: Right, left, or end

Color: Black or Yellow• Configurations:• o 2-Wire 10K resistive monitored o 2-Wire non-monitored o 4-Wire monitored o Pneumatic (MEP120) or air-wave (MAW120) Coil cord attached• Soft end plugs for specific non-door/gate applications• Mounting channels•

OPTIONS

Designed for gates

Designed for doors

SensingEdge Model: ME120

INSTALLATION

Place mounting channel in desired location. Drill 1/8” holes through channel into mounting surface every 24”.

Attach channel to mounting surface. Slide the sensing edge into mounting channel. If mounting in vertical position, use a screw at the bottom of the channel as a mechanical stop to prevent the sensing edge from slipping out of position. For detailed instructions, contact Miller Edge.

CARE & MAINTENENCE

Minimal care is required for ME120 since they are manufactured with the most durable materials and the highest quality control standards. However, sensing edges should be examined regularly for cuts or punctures, which could damage internal components.

Check wiring to be sure connections are secure. When properly maintained, both the MGR20 and the MGS20 offer years of trouble-free operation.

WARRANTY

Miller Edge, Inc. will replace within one year of shipment from factory, any sensing edge subject to normal use which is found to have defective materials or workmanship, as determined solely by our factory representative. Replacements will be shipped to you freight collect. This warranty is void where evidence of misuse or abuse is present.

P.O. Box 159 • West Grove, PA 19390 • 610-869-4422 • Fax: 610-869-4423 • 800-220-3343 6809 South Harl Avenue, Suite A • Tempe, AZ 85283 • 480-755-3565 • Fax: 480-755-3558 • 800-887-3343 www.milleredge.com

MECHANICAL DIAGRAMS

MOUNTING CHANNELS

ME120_20190212

Contact Miller Edge to ensure compatability with your operating controls.

U.S. Patent 6,571,512 Other patents apply.

ME120-C Aluminum (black)

ME120-PC Rigid PVC 9/16”

1 1/16”

1 7/16”

1 9/16”

1 1/16”

1 1/16”

ME120-C5 Aluminum (black)

TechTip: Swing Gate Sweep Edge The ME120 sensing edge paired with the ME120-C5 mounting channel creates a sweep edge that safeguards the entrapment zone on driveways and curbs along the path of travel below a swinging gate, as defined by UL325 and ASTM F2200.

ME120 + ME120-C5

SWING GATE SWEEP EDGE

Model: RB-G-K10

RB-G-K10

Receiver (RB-G-RX10) & Transmitter (RB-TX10)

FUNCTIONAL BENEFITS

The Miller Edge RBand is a wireless monitored transmitter/receiver kit for automated gate systems. It monitors the presence and function of T2 (10k) sensing edges and transmits a wireless monitored signal to the operator controls. The RBand Receiver can be paired with up to 6 Transmitters on 2 channels. The Transmitter is built to endure rugged, outdoor environments.

The Miller Edge RBand eliminates the need to hard wire sensing edges and meets 2016 UL 325 standards for commercial gate operators.

2 channel receiver compatible with up to• 6 total wireless transmitters

On-board diagnostics for easy• setup/troubleshooting

Bi-directional link improves immunity to• RF interference

Transmitter built to endure rugged• outdoor environments

2016 UL 325 Recognized Component•

2 year warranty•

RB-G-K10_Spec_20170130

P.O. Box 159 • West Grove, PA 19390 • 610-869-4422 • Fax: 610-869-4423 • 800-220-3343 6809 South Harl Avenue, Suite A • Tempe, AZ 85283 • 480-755-3565 • Fax: 480-755-3558 • 800-887-3343 www.milleredge.com

Applications

• Monitored Gate Edges

RBAND

MONITORED WIRELESS GATE TX/RX

TECHNICAL SPECIFICATIONS

PHYSICAL

TX Dimensions 1.80”L x 4.78”W x 1.75”H

TX Weight 4.5 oz

TX Enclosure Material Polycarbonate

TX Rating NEMA4

RX Dimensions 4.12”L x 3.65”W x 1.65”H

RX Weight 5.25 oz.

RX Enclosure Material Steel

MECHANICAL

Operating Temperature -40°F to 140°F

Frequency 916 MHz

Operating Range 50’ nominal; 100’ optimal conditions

ELECTRICAL

TX Power Source 2 AA, 3.6 V lithium

TX Battery Life 2-year expectancy

TX Input 10K monitored edge

RX Power Source 12-24 VAC/DC nominal, 100 mA maximum

RX Outputs 10K, N.C.