Attachment 4 Camera Specifications.pdf

Attachment 4

CAMERA SPECIFICATIONS:

PTZ Camera Specifications

Imager: 1/2.8 in. CMOS sensor

Effective Picture Elements (Pixels): 1944 x 1212 (2.35 MP)

Lens: 30x motorized Zoom 4.3 mm to 129 mm F1.6 to F4.7

Field of View (FOV): 2.3° to 64.7°

Focus: Automatic with manual override

Iris: Automatic with manual override

Digital Zoom: 12x

Day/Night switch: Automatic IR cut filter

Video performance-Sensitivity: (3100K, reflectivity 89%, 1/30, F1.6, 30 IRE)

Color: 0.0077 lx

Monochrome: 0.0008 lx

Video performance-Dynamic range

High dynamic range 120 dB WDR

Measured according to IEC 62676 Part 5100: dB WDR

Additional Camera Settings:

Gain control: AGC, Fixed, Region per pre-position

Aperture Correction: Horizontal and vertical

Electronic Shutter Speed (AES): 1/1 sec to 1/30,000 sec (22 steps)

Signal-to-Noise Ratio (SNR): >55 dB

Backlight compensation (BLC): On / Off / Intelligent Auto Exposure (IAE)

White balance: 2000 K to 10,000 K ATW, AWB Hold, Extended ATW, Manual, Sodium Lamp Auto, Sodium Lamp, indoor, outdoor

Day/Night: Monochrome, Color, Auto

Defog mode feature: Improves visibility when viewing foggy or other low-contrast scenes.

Noise Reduction: Intelligent Dynamic Noise Reduction

Frame Rate: 1080p: 30fps; 720p:, 60fps

Resolutions (H x V) 1080p HD: 1920 x 1080

720p HD: 1280 x 720

1.3 MP 5:4 (cropped): 1280x 1024

D1 4:3 (cropped): 704 x 480

640x 480: 640 x 480

432p SD: 768 x 432

288p SD: 512 x 288

144p SD: 256 x 144

Ethernet: 10BASE-T/100BASE-T, auto-sensing, half/full duplex

Encryption: TLS 1.2, DES, 3DES, AES

Ethernet connector: RJ45

GOP Structure: IP, IBP, IBBP

Data Rate (H.265, 1080P): 61 kbps to 2.8 Mbps (depending on the scene, the frame rate, and the quality settings)

Overall IP Delay 60 fps: 166 ms (typical) 30 fps: 233 ms (typical)

Interoperability ONVIF Profile S, ONVIF Profile G, ONVIF Profile T

Protocols: IPv4, IPv6, UDP, TCP, HTTP, HTTPS, RTP/RTCP, IGMP V2/V3, ICMP, ICMPv6, RTSP, FTP, ARP, DHCP, APIPA (Auto-IP, link local address), NTP (SNTP), SNMP (V1, V3, MIB-II), 802.1x, DNS, DNSv6, DDNS (DynDNS.org, selfHOST.de, noip.com), SMTP, iSCSI, UPnP (SSDP), DiffServ (QoS), LLDP, SOAP, Dropbox™, CHAP, digest authentication

Network:

Video compression: H.265, H.264, M-JPEG

Streaming: Four (4) streams: Two (2) configurable streams in H.264 or H.265; One (1) I-frames-only stream based on first stream; One (1) M-JPEG Stream

Mechanical Pendant Pan Range 360° cont.

Tilt Angle: 18° above horizon

Pre-position Speed Pan: 400°/s Tilt: 300°/s

Pan/Tilt Modes •

Turbo mode (Manual Control): Pan: 0.1°/s - 400°/s Tilt: 0.1°/s - 300°/s

Normal Mode: 0.1°/s-120°/s 0.1°/s-120°/s

Pre-position Accuracy: ± 0.1° typ. ± 0.1° typ.

Electrical

Input voltage: 24 VAC 60 W (using the midspan accessory NDP-6001B, required to power the heater) 30

W (IEEE 802.3at, class 4 standard, when used without powering the heater)

Power Consumption (typical), with heaters 51.0 W / 54.0 VA

Power Consumption (typical) 19.2 W / 33.6 VA (without heaters) 19.2 W / 33.6 VA (heaters off / without heater connected in 24 V power supply box)

Current consumption, 24 VAC

Current consumption, 60 W

Redundant configuration: Connect both a 60 W midspan and a separate 24 VAC power source. If either power source fails, the camera switches automatically to the other power source.

Fixed Camera Specifications

Camera

Imaging Device: ½.8inch

Imager Type: CMOS

Imager Readout: Progressive Scan

Highest Resolution: 3MPx/2048x1536, 2MPx/1920x1080, 1MPx/1280x960

Signal-to Noise Ratio: >60dB

Auto Back Focus: yes

Electronic Shutter Range: 1/20000 sec to 2 sec

True Wide Dynamic Range : 130dB

White Balance Range: 2,000° to 10,000°K

Day/Night Capabilities: Yes

Mechanical IR Cut Filter: Yes, (ON/OFF/AUTO Selectable), with different set points on lux

Sensitivity: ff/1.3; 2,850°K; SNR >20 dB Color (33 ms) 0.050lux, Color (500 ms) 0.005lux, Mono (33 ms)

0.010lux, Mono (500 ms) 0.001lux

Network

Supported Protocols: TCP/IP, UDP/IP (Unicast, Multicast IGMP),UPnP, DNS, DHCP, RTP, RTSP, NTP, IPv4, IPv6,SNMP v2c/v3, QoS, HTTP, HTTPS, SSH, SSL,SMTP, FTP, ARP, ICMP, and 802.1x (EAP), NTCIP 12

Security Access: Password protected

Software Interface: Web browser view and set up

Mechanical

Lens Mount: CS mount

Auto Iris Type: DC Auto Iris

Camera Mount: ¼ in. UNC-20 screw C10-UM

Field of View: Recommended Lenses

Electrical

Network Port: RJ-45 connector for 100 Base-TX Auto MDI/MDI-X

Cable Type: Cat5 or better for 100 Base-TX

Input Power: PoE (IEEE 802.3af, Class 3), 24 VAC ±10%, 12VDC ±10%

Power Consumption: Up to 12W nominal

Current Consumption: 330 mA @ POE; 0.5 A @ 24 VAC;1A @ 12 VD

Alarm: Unsupervised detects open or closed alarm state, Input 5 VDC maximum 0.5mA maximum

Relay Output: ±350V VDC maximum, ±130 mA maximum

Video

Video Streams: Independently configurable primary and secondary streams plus service stream

Available resolutions: Two configurable streams

Maximum Frame Rate: Up to 60 frames per second, 30fps with WDR

Video Encoding: H.264 High, Main, or Base profiles and MJPEG

Bit Rate Control: Constrained variable bit rate (CVBR) and constant bit rate (CBR)

Corridor Mode: Electronic image flip and mirror: 180°, 90° and 270° (H.264 only)

Service Stream: JPEG stream; 640x480 or 640x360, up to 15 fps

Camera Location Information

Bldg. 1220 (Attachment 2, Page 1)

Fixed Camera: Ceiling mounted in the center corridor of bldg. 1220 facing east

Field of view: Back door leading to flight line

Scope: New camera, mount, above ceiling tiles conduit, wiring to the closest node located in communications closet approximately 150ft away, new electrical components as necessary

ECP 1 (Attachment 2, Page 2)

PTZ Camera: Pole mounted on pendant facing S/SW

Field of view: Outbound/Inbound ECP 1

Scope: Remove current camera and wiring, install exterior rated CAT6 wiring using existing underground conduit path to communication node approximately 90ft away, replace or install new electrical components as necessary

ECP 18 (Attachment 2, Page 3)

PTZ Camera: Pole mounted on pendant at the corner of Rex Rd.

Field of view: Full Coverage of ECP 18 underground conduit path to communication node approximately 280ft away, and install new

ECP 17 (Attachment 2, Page 4)

PTZ Camera: Pole mounted on pendant at the north side of ECP 17 facing south.

Field of view: In/Outbound gate of ECP 17 underground conduit path to communication node approximately 200ft away, and install new

ECP 15 Inbound & ECP 16 (Attachment 2, Page 5)

PTZ Camera: Wall mounted on NW corner of bldg. 1225 (Hangar 8)

Field of view: ECP 15 In & ECP 16

Scope: New camera, mount, above ground conduit, wiring to the closest node located in communication closet approximately 200ft away within Hangar 8, new electrical components as necessary

ECP 22 Inbound (Attachment 2, Page 6 & 7)

PTZ Camera: Pole mounted on pendant at corner of ECP 22 Inbound

Field of view: Full Coverage of ECP 22 Inbound/ECP 23 (Turnstile)

Scope: New pole, new camera, mount, conduit, wiring to the closest communication node approximately 85ft away, and new electrical components as necessary

ECP 24 Inbound (Attachment 2, Page 8 & 10)

PTZ Camera: Pole mounted on pendant at corner of ECP 24 Inbound

Field of view: Full Coverage of ECP 24 Inbound

Scope: New pole, camera, mount, underground conduit (may be available already, but must be inspected), wiring to the closest communication node approximately 200ft away, and new electrical components as necessary

ECP 24 Outbound (Attachment 2, Page 9 & 10)

PTZ Camera: Pole mounted

Field of view: Facing vehicles exiting through the gate

Primary location (Green): Secure side of ECP 24 outbound

Scope: New pole, camera, mount, underground conduit (may be available already, but must be inspected), wiring to the closest communication node approximately 125ft away, and new electrical components as necessary

Secondary location (Orange): Fence line adjacent to ECP 24 outbound

Scope: Existing pole must be extended or replaced, camera, mount, underground conduit (may be available already, but must be inspected), wiring to the closest communication node approximately

15ft away, and new electrical components as necessary