Attachment 1 CUI Non-Nuclear CMD List 13 May 2021.pdf

CUI

DEPARTMENT OF THE AIR FORCE

AIR FORCE LIFE CYCLE MANAGEMENT CENTER (AFMC)

HANSCOM AIR FORCE BASE, MASSACHUSETTS

MEMORANDUM FOR DISTRIBUTION

FROM: Force Protection Division, AFLCMC/HBU

SUBJECT: Non-Nuclear Configuration Management Database (CMD) Equipment Approval

1. The CMD equipment listed below is approved for use when employed in the tested PL-1 Non- Nuclear through PL-4 applications and configurations (information can be obtained from AFLCMC/HBU). This letter consists of nine pages.

* Indicates correction, change, and/or addition.

+ Indicates item is no longer procurable and/or supported by Original Equipment Manufacturer (OEM).

NOTE: Items marked with a (+) are no longer authorized for purchase; however, previously installed systems will remain on this list as legacy systems and for fixed site sustainment support IAW with AFI 31-101, Chapter 9. Contact AFSFC/S5G at afsfc.ibdss@us.af.mil with any questions concerning these items.

PL-1 Non-Nuclear and Below

Command, Control Display Equipment (CCDE)

LINX Annunciator (formely known as Will-Burt Annunciator):

LINX Annunciator Predator Elite, with integrated access control:

Annunciator Version 3.2.274p, subpatch p32274.1.13 LINXSNMP version 3.3.274P, subpatch 3.3.274P.1.13.30 Annunciator Version 3.3.274p, subpatch p33274.1.13.33 + Annunciator Version 3.2.274p + Annunciator Version 3.0.252 + Annunciator Version 3.0.246 Annunciator Version 8.1 (Win 10) LINX Predator Enrollment System Version 4.1.220 + LINX Predator Enrollment System Version 4.0.203 LINX Versatile Interface Panel (VIP) Version 1.172 LINX Versatile Interface Panel (VIP) Version 1.148 LINX Versatile Interface Panel (VIP) Version 1.64 *LINX Versatile Interface Panel (VIP) Version 8.116 LINX Versatile Interface Panel, Expandable (VIP-E) Version 7.284 LINX Versatile Interface Panel, Expandable (VIP-E) Version 7.145 *LINX Versatile Interface Panel, Expandable (VIP-E) Version 7.288 *LINX Versatile Interface Panel (VIP-16i) Version 1.09 + WSD 2000 Card Reader version 1.8V + WSD-E Card Reader version 3.110 *WSD-E Card Reader version 3.111

Advantor Annunciator:

+ Advantor Advantage Suite for Networks (ASN) Version 4.0 + Advantor Advantage Suite for Networks (ASN) Version 5.0 + Advantor Integrated Command, Control, and Access Control System Version 5.0 + Advantor Integrated Command, Control, and Access Control System Version 5.0 Service Pack 6 Advantor Integrated Command, Control, and Access Control System Version 6.0 Advantor Advantage Suite for Networks (ASN) Version 6.2 (Win 10)

Vindicator Annunciator:

Vindicator Security Management and Reporting Terminal (SMART) Annunciator with Graphics Display:

+ Version 2.40 with Administrative Browser 4.0 + Version 2.43, Build 11 + Vindicator Command and Control (VCC) Version 1.0.1.5 + Vindicator Access Control System (ACS) Version 2.3, Build 21 + Transponder Firmware Version 2.28 + TS 4000 Radio Frequency (R/F) Modem Interface + Vindicator SMART with Graphics Display Version 2.39 and SAW Version 3.9 + Vindicator Command and Control Platform (VCCP) v5- Version 5.0 + Vindicator Command and Control Platform (VCCP) v5- Version 6.0 + Vindicator Command and Control Platform (VCCP) v5- Version 6.5 (Win 7, 32 bit only) + Vindicator Command & Control (VCC) GUI Version 5.1.1.4 + Vindicator Badge Manager 2 (VBM 2) Version 2.0.7.0 + Vindicator Badge Manager 2 (VBM 2) Version 2.0.7.1 (Win 7, 32 bit only) + Vindicator Security Archive Workstation (SAW 5) Version 5.1.0.6 + Honeywell Vindicator Site Commander Version 1.2.0.1 + V5 IDS Network Security Appliance – Intrusion Detection, Revision 3.2, Release 20:

UHS-8270

DES-8270T

AES-8270T

+ V5 ACS Network Security Appliance – Access Control Revision 3.2 Release 20:

UHS-1401

DES-1401T

AES-1401T

+ Vindicator UHS-Net Gateways:

UHS-8101 Version 2.33, Build 7 UHS-8102 Version 2.33, Build 6 UHS-8301 Version 2.33, Build 13 UHS-8400 Version 2.33, Build 13

+ Vindicator UHS-Net Transponder/Gateway Revision 3.3, Release 5:

UHS-1500

DES-1500T

AES-1500T

+ Vindicator UHS-Net Transponders Version 2.33, Build 13:

UHS-6842

UHS-6842F

DES-6842

DES-6842F

+ PC SMART PAC Software Package Version 5.1 + Proteus 5 & SmartSave 5 Software Programs Version 5.2 Vindicator Command and Control Platform (VCCP) Windows 7 (64-bit):

Vindicator Command & Control 2-Version 1.2.1.4 V5 Network Security Application for IDS & ACS-Version 3.2, Release 23

UHS-1500 UHS-Net Field Panel-Version 3.3, Release 7 Security Archive Workstation 2-Version 1.4.2.9 Vindicator Badge Manager 3-Version 2.0.26.7 Vindicator Site Commander-Version 1.3.0.7 Vindicator Area Commander-Version 1.1.0.6 Vindicator Premise Controller-Version 3.3, Release 7 Vindicator PC SMART PAK-Version 6.0.0.1 Vindicator Security Server-Version 1.0

Vindicator 10 Annunciator Workstation (Win 10 LTSB) Vindicator Command and Control 2-Version 1.3.0.2 SP4 Vindicator Security Server-Version 1.0 V3 Head-End Server (IDS & ACS)-Version 4.3.2 SP VR11 V5 Network Security Appliance-Version 4.5.2 SP VR11 AES-1500Network Field Device-Version 4.3.2 SP VR11 Security Archive Workstation 2-Version 1.4.3.0 Vindicator Badge Manager 3-Version 2.0.26.7 Vindicator Site Commander-Version 1.3.0.7 Vindicator Area Commander-Version 1.1.0.7 Vindicator Premise Controller-Version 4.3.2 Vindicator PC Smart PAC (PCSP)-Version 6.0.0.1 Vindicator System Terminal-Version Win 10 LTSB

LENEL Annunciator:

LENEL OnGuard Version 7.5 with Milestone Version 12.3 NOTE: Not approved with any Ground Based Radars

Assessment Subsystems:

Video Servers:

Advantor Video Management System (VMS) Software (For use only with Advantor ASN 6.0):

Advantor VMS Version #va-advantorvms-3.3.22-1 (1/el5) Advantor VMS Wall Version ds-vmx-3.3.1-3

+ Bosch Allegiant Matrix/Control System LTC 8600 and 8800 + Broadware 4.80 / Cisco 5.1.1. Video Storage System (NOTE: Cisco renamed the 4.80 after purchasing Broadware.)

+ Video Image Control and Display System (VICADS) Version 4.0 Video Management System + Prometheus Security Group Global (PSGG) (Formerly Open Roads Consulting, Inc.) Video Image Control and Display System (VICADS) Version 4.1 Video Management system using Vindicator V5, Version 6 as the annunciator

+ PSGG Video Image Control and Display System (VICADS) Version 4.1 Service Pack 1.6 Video Management system using Vindicator V5, Version 6.5 as the annunciator

+ PSGG Video Image Control and Display System (VICADS) Version 4.1 Service Pack 1.6 Video Management system using Linx Predator Elite Version 3.2.274p, subpatch p32274.1.13 as the annunciator

+ PSGG Video Image Control and Display System (VICADS) Version 4.1 Service Pack 2.0 Video Management system using Vindicator VCCP Windows 7 as the annunciator. Note: DefendIR Thermal imager protocol support, RadarWall, and Geoserver are not approved for use

+ PSGG Video Image Control and Display System (VICADS) Version 4.1 Service Pack 2.4 Video Management system using Vindicator VCCP Windows 7 as the annunciator. Note: DefendIR Thermal imager protocol support, RadarWall, and Geoserver are not approved for use.

+ PSGG Video Image Control and Display System (VICADS) Version 4.2.7 build 134 using Linx Predator Elite Version 3.3.274p, subpatch p33274.1.13.33

+ PSGG Video Image Control and Display System (VICADS) Version 4.2.7 build 134 using Vindicator 7 as the annunciator

PSGG Video Image Control and Display System (VICADS) Version 4.3 using LPE v8.1 (Win 10) PSGG Video Image Control and Display System (VICADS) Version 4.3.2 using Vindicator (Win 10)

Assessment Cameras:

Axis Q1645 Fixed Camera Axis P3245-LVE Axis Q3527-LVE Axis Q6075 Indoor PTZ Axis Q6075-E Outdoor PTZ Axis Q6215-LE PTZ

Bosch 8001 Fixed Thermal Camera (Model:NHT-8001-F35VF) Bosch MIC IP Starlight 7100i (Model:MIC-7522-Z30W) + Bosch NWC-04-95-20P Internet Protocol (IP) Camera + Bosch NWC-04-95-20P (1/3 Format) + Bosch NBN-498-21P Internet Protocol (IP) Camera Bosch Auto Dome IP Starlight 7000i Camera (Model:NDP-7512-Z30) + Bosch Auto Dome VG 4-322-ECE1M + Bosch Auto Dome VG5-623-ECS + Bosch Auto Dome VG5-624-ECS + Bosch Auto Dome VG5-724-ECE2 + Bosch Auto Dome 7000 Internet Protocol (IP) Camera with environmental housing + Bosch Dinion Internet Protocol (IP) 7000 Camera with environmental housing Bosch DINION Internet Protocol (IP) Starlight 7000 HD (NBN-73013-BA) Bosch NBN-63013-B Bosch NBN-63023-B Bosch Flexidome Starlight 8000 Dual SD Variant must be used or WLAN Disabled + Bosch NBN-71013-B + Bosch NBN-71022-B + Burle 300H Camera + Burle TC 351 Camera (1/2 inch format) + Cohu 4865 Camera (WS3) (2/3 inch format) + Cohu 48x Camera (KUMMSC) (2/3 inch format) + Cohu 4915/4912-3000 Camera (1/2 inch format) + Cohu 3930HD + Indigo Vision 512147 (PTZ) + Indigo Vision 11650-Audio-HD + IQ Eye 752 Internet Protocol (IP) Camera + Lumenera Le 165M-DN Internet Protocol (IP) Camera + Lumenera Le 165ME-DN Internet Protocol (IP) Camera with environmental housing + Lumenera Le 165MP-DN Internet Protocol (IP) Camera with environmental housing + Pelco ES31CBW35-2N Pan Tilt Zoom (PTZ) System + Pelco ES30C/ES31C Pan Tilt Zoom (PTZ) System (1/4 inch format) with/ without optional Wiper + Pelco ES4136-2N Esprit ES system Pan Tilt Zoom (PTZ) System (1/4 inch format) with/ without optional Wiper

+ Pelco MC3651H-2 Interior Camera (1/3 inch format) + Pelco IXE20 IP Camera + Pelco ES4036-5W Esprit Series, with and without wiper, standard and pressurized + Pelco ES40E36-5W Esprit Series, with and without wiper, standard and pressurized + Pelco ES40/41 Series Positioning System, Analog, PTZ, w/wo wiper Esprit SE Standard & pressurized, model ES4036-5W

+ Pelco ES40E/41E Series Positioning System, IP, PTZ, w/wo wiper Esprit SE Standard & Pressurized, Model ES40E36-5W

+ Pelco IXE21 Internet Protocol (IP) Pelco P1220-ESR1 (PTZ) Pelco Sarix IXE Series Box Cameras w/ SureVision 3.0

+ VICON SN680D-B-WNIR (PTZ)

+ VICON IQ762WI-V6 Internet Protocol (IP) + Vivotek IP 7151 + Vivotek SD8364E (PTZ) + Vivotek IP816A-HP (interior only)

Interior Sensors:

NOTE: Balanced Magnetic Switch (BMS) will not be used as a line of detection.

+ AN/GSS-20 Volumetric

+ AN/GSS-9(V) SA 1955 BMS

+ AN/GPS-15(V) Closed-Shelter Aircraft Sensor (C-SAS) (Volumetric) + AN/GSS-36(V) Open-Shelter Aircraft Sensor (O-SAS) (Volumetric) Banner Engineering Series Active Infrared (AIR), intrinsically safe, Model SMI30 (Must be installed as an array of individually reporting sensor points, for use across openings in areas where explosive fumes may be present)

+ Bosch DS 9370 PIR/MW (Volumetric) + Bosch DS 939 PIR (Volumetric) BEA LZR-s600 BEA LZR-i30 Dortronics 1110 xD xCT, Magnetic Lock/BMS Dortronics 1120 x2D xCT, Series Electromagnetic Lock and BMS Eltec 862 Passive Infrared (PIR) Sensor (Wall) + Fiber Sensys EX-35T Passive Infrared (PIR) + Fiber Sensys AP2-20N Passive Infrared (PIR) Fiber Sensys LD308SH Fiber Sensys LD204S + General Electric (Sentrol) Model 2700 Series BMS + General Electric (Sentrol) Model 2807T Explosion Proof Balanced Magnetic Switch (BMS) + General Electric (Sentrol) Model 2507AH-L Wide Gap BMS + General Electric (Sentrol) Model 2800 Series BMS + General Electric AP669 PIR (Volumetric) Magnasphere, High Security Sensor (HSS) Door Contact Switch, BMS, Version HSS-L2S-000 Magnasphere L2C-101 (Concealed switch) Magnetic Contact Switch Magnasphere L2C 101A (Recessed Switch) Magnetic Contact Switch Magnasphere Interior Barrier Sensor Model MSK-101-MM Magnasphere Interior Motion Sensor Model MSK-101-MM + PL&E Communications AVT 234 (VMD) using Dinion analog infrared imagers, for interior applications only

ASSA ABLOY (Securitron Group) MSS-1 High Security Balanced Magnetic Switch East Coast Security Products Inc. ESM-6T Tandem Balanced Magnetic Switch Protech Passive Infrared and Microwave Intruder Detectors (PIRAMID) SDI-76-G (Volumetric) Protech Passive Infrared and Microwave Intruder Detectors (PIRAMID) SDI-77-D (Volumetric) Protech SDI-76M-HS1-H Volumetric (Coverage 60’x 40’, Two Sensors in Combination) Protech SDI-76MW Volumetric (Coverage 60’x 40’, Two Sensors in Combination) Protech SDI-77XL2-EX, Explosion Proof Volumetric Optex Redscan RLS-3060SH Laser Scan Detector (Approved for wall and ceiling configurations) *Optex SX360Z PIR

+ SightLogix SightSensor Video Motion Detection (VMD) using NS-90A Thermal Imager, for interior applications only.

+ United Technologies Interlogix AP669 Mirror Optic PIR (Volumetric) + Visonic CH-1000 (Wall) + Visonic CH-1000 + Xtalis ADPRO 18 WH PIR Combination (Ceiling) (Coverage 30’x 30’) + Tyco Visonic Disc 360 Passive Infrared Sensor (Ceiling) (Coverage 360 Degree) Protech Maxiris 3000/3100 Active IR Interior Sensor + AN/GSS-39(V) Interior Intrusion Detection System. Components include:

-- DR-301 -- DR-558 -- DR-851 -- HT-50B

-- HT-50DC -- HT-100B -- HT-100BC -- SDI-76A

-- SDI-77C -- SD-80B -- SD-80EHB -- SD-150B

-- SD-150EHB -- SRN-2000H

Exterior Sensors:

The following sensors are approved for use as a standalone line of detection:

BEA LZR-s600 (ECP Configuration) BEA LZR-i30 (ECP Configuration) EAG of Americas Infrared Intrusion Detection System 4/2/2 (IIDS4/2/2) Active Infrared Sensor EAG of Americas Infrared Intrusion Detection System 4/4/2/2/2 w/ PSTC EAG of Americas Intrusion Detection System 4/2 (IDS 4/2) Active Infrared Sensor IR Global Infrared Intrusion Detection System 4/4/2 IR Global IRG-509-15M + Microtrack buried line sensor (NOTE: Not approved for use in Northern tier, or areas where snow and ice accumulations are normal, pending further testing)

Senstar Omnitrax buried line sensor firmware version MSP v2.81 w/Field Programmable Gate Array (FPGA) v13.05

Senstar Omnitrax buried line sensor w/Firmware Version MSP v2.90 w/FPGA v13.93 Senstar Ultrawave Detection Sensor TE (W/Whiteman AFB tamper protection modification) + Perimitrax, Buried Cable Intrusion Detection Sensor Protech (PIRAMID) / SDI-76-XL-MIL, PIR and Monostatic Microwave Sensor Protech (PIRAMID) / SDI-76-XL-MIL LT (Ladder and Tower) Only Protech Sorhea Technology G-Fence 600 Zoning (600Z) System Protech Sorhea Technology G-Fence 600 Zoning (600Z) System culvert configuration Protech Maxiris 3100 Active Infrared Barrier (100 meter) + Racon Single Stack; Barksdale Configuration - single stack, basket weave configuration with double stacked sensors at the corners

+ Racon Double Stack + Racon 16000-4 (Microwave) Sensor + Racon 14000-32 Microwave Sensor + Racon MPS-4100 (Microwave) + Racon MPS-14000-1 (Microwave) Senstar UltraWave Microwave Detection Sensor Senstar UltraWave Microwave Detection Sensor (Firmware 3.05) + Senstar Sentrax Short Ported Coaxial Cable Sensor (SPCS), large and small diameter cable, in the straight-line configuration

+ Birdeye Model IX Infrared Perimeter Detection System, up to 120m DeTekion Defensor 100 Fence Sensor DeTekion Defensor 100 sensor system with the GD-5000 Eliminator signal analyzer DeTekion Vertical Taut Wire Sensor 400 (VTW-400), full fence or out-rigger configuration ECSI Infrared Pulsed Intrusion Detection System (IPIDS), up to 80m with spring loaded mount bases and 100m with solid concrete bases

Fiber SenSys Fiber Defender +FD200/300 series. The following models have been tested:

331, 332, 341, and 342. Note: The 331 and 332 series is with “Sensitive” Lead-in cables whereas the 341 and 342 series is with the “Insensitive” Lead-in cables. Also, the last digit (1 or 2) indicates a single channel processor or dual channel processor. Additional note: The 33x series is normally utilized for TASS applications with the 34x series being utilized for all hardwired configurations.

Fiber Sensys Fiber Defender FD-342, v4.47 Fiber Sensys Fiber Defender FD-342, v4.47 (Culvert Configuration) + Fence Protection System 2-2R (FPS-2-2R) Senstar FlexZone Fence Sensor (NOTE: Not approved for use in Northern tier, or areas where snow and ice accumulations are normal, pending further testing)

RBtec Ironclad Fence Sensor Double Run Configuration + Southwest Microwave Intrepid Micropoint. (NOTE: Not approved for use in Northern tier, or areas where snow and ice accumulations are normal, pending further testing) tier, or areas where snow and ice accumulations are normal, pending further testing) Southwest Microwave Intrepid Micropoint II.

Southwest Microwave 385 Monostatic Sensor, up to 100m Southwest Microwave 310 Bi-static Sensor, up to 100m Southwest Microwave 460B Active Infrared Exterior Sensor Southwest Microwave 330 Digital Microwave System + Fiber Optics Intrusion Detection System (FO-IDS), Fiber Optic Sensor System (FOSS) Models 100 and

Fiber SenSys Fiber Defender 525 (Note: Not approved for use in Northern tier, or areas where snow and ice accumulations are normal, pending further testing)

The following sensors in combination are approved for use as a line of detection with fence climber enhancement detection:

+ Enhanced DTR-90 Vertical Taut Wire (VTW) Sensor, the DTR 90 “Y” VTW Sensor, or the VTW 400 Sensor installed at the top of the fence with any one of the following sensors installed on the fence:

Fiber SenSys Fiber Defender FD300 series. The following models have been tested: 331, 332, 341, and 342.

+ Fence Protection System 2 (FPS-2) + Fence Protection System 2-2R (FPS-2-2R)

Wide Area Detection/Approach Zone Sensors:

+ PSRS STS-350 (FLIR/ICx) Ground Based Radar used as an approach sensor out to 125 meters (crawlers) as described below: ICX application software version 2.4.41.12 Firmware version 3.4.30 dated November 2, 2007.

+ PSRS STS-350 (FLIR/ICx) with control station application software version 2.4.41.12 or when integrated with Will Burt Annunciator Version 3.2.274p, subpatch p32274.1.13.

FLIR Ranger 1 Perimeter Surveillance Radar (700 meters) FLIR Ranger 2 Perimeter Surveillance Radar (1400 meters) FLIR Ranger 3 Perimeter Surveillance Radar (2800 meters) Magos SR-500 Perimeter Surveillance System when integrated with the Advantor Systems ASN, Version

6.2. MASS Version 2.24.10053, SR-500 Radar Version 3.64 and Radar Manager Version 1.5

SpotterRF C40D Integrated with Advantor Version 6.2 (Note: Not approved for use in Northern tier, or areas where snow and ice accumulations are normal, pending further testing)

PL-3 and Below

In addition to all of the above components, the following equipment is approved for use in the protection of PL-3 and below assets:

Command, Control Display Equipment (CCDE):

+ TASS 7.0 Annunciator (At deployed locations only) TASS 6.0.1.A Annunciator (At deployed locations only)

Assessment Subsystems:

Clear Align VZ-250 LRTI 23164-600 Clear Align VZ-250 LRTI 23164Z1-600 (Improved Cooling) Clear Align LRTI-w/CCTV

C907891 Complete Kit TICC/PTH only C907892

+ FLIR ThermoVision Multi-Sensor System (a.k.a. SLRTI) T-2000 LRTI w/CCTV Complete Kit IBDSS1000-085 T-2000 LRTI w/CCTV TICC/PTH only IBDSS1000-086 T-3000 LRTI w/CCTV Complete Kit FDTA-199 T-3000 LRTI w/CCTV TICC/PTH only

+ Surveillance Thermal Imager (WSTI) Sentry I and Sentry II

FLIR DEFENDIR MS-UC 640 30/90MM CZ

+ Short Range Thermal Imager; Fixed/Mounted (SRTI F/M) + DiOP Thermal Imager 180/60mm Thermal Upgrade Kit (TUK)

Interior Sensors: No Additional

Exterior Sensors: No Additional

Certified Air Force Test Sites:

Test Area C-3, Eglin AFB FL, and Cold Weather Test Site, Grand Forks AFB, ND are approved for conducting operational tests and evaluations on all IDS equipment.

2. All equipment was determined to meet all applicable TAA/BAA/NDAA requirements at the time of approval. Manufacturers could change place of origin over time. Installation agents should verify place of origin of all components prior to installation.

3. A listing of equipment approved for use in PL-1 Nuclear applications is available in a separate letter maintained by the POC listed below.

4. This memorandum supersedes the 28 Jan 21 IDS approval memorandum. The POC for this effort is 1st Lt Joshua Scollo, AFLCMC/HBUA, joshua.scollo@us.af.mil, DSN 845-5275.

LINDA W. HAINES, NH-04, DAF

Senior Materiel Leader Force Protection Division

DISTRIBUTION:

AFDW/A4S

HQ USAFE/A4S

HQ AFMC/A4S

HQ PACAF/A4S

HQ AETC/A4S

HQ AFSFC/S5G

HQ AFSPC/A4S

HQ AFSOC/A4S

HQ AFRC/A4S

HQ AMC/A4S

HQ ACC/A4S

HQ AFGSC/A3S

NGB/A4S

HQ USAFA/SF

HQ USAF/A4SX

HQ USAF/A4SO

HQ AFLCMC/HNC (CCSD)

Date1_af_date: 13-May-2021