Attachment 3 - B191 - Conceptual Drawings.pdf

SOSM DEMO PLAN

Scale: 1/2" = 1'

SOSM FLOOR PLAN

Scale: 1/2" = 1'

DEMO PLAN KEYNOTES

LEGEND

EXISTING WALL OR FURRING TO REMAIN

ITEM TO BE DEMOLISHED

1. (E) WALL TO REMAIN

2. DEMO (E) WALL

3. DEMO (E) DOOR

4. DEMO (E) PLAM DESK

5. REMOVE (E) SINK AND VANITY AND CAP ROUGH PLUMBING

6. DASHED LINE INDICATES SECTION OF (E) DRYWALL TO BE REMOVED TO ACCOMMODATE PLUMBING

INSTALLATION AND/OR BE REPLACED WITH MOISTURE RESISTANT DRYWALL, TYP AT ALL WET WALL

LOCATIONS

7. REMOVE SHOWER DRAIN AND ASSOCIATED BRANCH LINE BACK TO (E) 4" MAIN

8. REMOVE (E) TOILET AND ASSOCIATED WASTE LINE BACK TO MAIN. REMOVE WATER HAMMER

ARRESTOR AND ACCESS PANEL

9. REMOVE (E) SHOWER SURROUND AND IN-WALL ROUGH PLUMBING

10. (E) ALERT LIGHTING TO REMAIN ACTIVE

11. REMOVE DRYWALL AS REQUIRED TO ACCESS TOILET VENT PIPE FOR SINK DRAIN LINE TIE-IN.

LEGEND

NEW STEEL STUD FRAMED WALL OR FURRING

EXISTING WALL

FLOOR PLAN KEYNOTES

1. (N) WALL MOUNT SINK AND VANITY. PROVIDE 18"W X 30" TALL WALL MOUNTED MIRROR CENTERED OVER

SINK. TIE DRAIN LINE INTO EXISTING TOILET VENT PIPE.

2. NEW CLEANOUT.

3. NEW 60" X 36" X 80" PRE-MANUFACTURED SOLID SURFACE SHOWER PAN AND SURROUND, CONNECT TO

EXISTING DRAIN, INSTALL OVER NEW "REDGUARD" DRAINAGE SYSTEM.

4. (N) SHOWER HEAD AND CONTROLS AT THIS LOCATION. HEAD SHALL BE 7'-0" AFF AND CONTROLS SHALL

BE 3'-6" AFF, CENTERED IN WALL.

5. EXTEND HW AND CW LINES OVERHEAD AND DOWN FURRED WALL TO SUPPLY LOCATION. ROUTE (N)

VENT LINE WITHIN FURRED WALL AND CONNECT ABOVE CEILING TO EXISTING VENT LINE. PROVIDE WALL

CLEANOUT.

6. (N) FLOOR MOUNTED ADA TOILET WITH COMMERCIAL FLUSH VALVE

7. (N) 2'-8" X 7'-0" SOLID WOOD POCKET DOOR WITH PAINTED WOOD CASED OPENING ON ALL SIDES. CLEAR

OPENING WHEN DOOR IS FULLY OPEN SHALL BE 2'-8" WIDE. FRAME POCKET WALL WITH 20GA 2-1/2" COLD

ROLLED STEEL STUDS.

8. NEW WALL CONSTRUCTION, RELOCATE (E) LIGHT AND (E) FAN CONTROLS, SEE GENERAL NOTES BELOW, PROVIDE FULL DEPTH MINERAL WOOL SOUND BATTS

9. INSTALL NEW WALL MOUNTED ACCESS PANEL AND WATER HAMMER ARRESTOR OVER TOILET

10. PATCH, TEXTURE, AND PAINT AREAS AFFECTED BY SINK REMOVAL

11. (E) ALERT LIGHTING TO REMAIN IN PLACE

12. REPAIR DRYWALL REMOVED FOR SINK DRAIN LINE TIE-IN. TEXTURE AND PAINT TO MATCH EXISTING, PAINT ENTIRE WALL AS REQUIRED FOR UNIFORM FINISH

GENERAL NOTES

1. PROVIDE MOISTURE RESISTANT DRYWALL AT ALL WET WALLS AND SHOWER WALLS

2. AT ALL AREAS THAT REQUIRE DRYWALL PATCH, TAPE AND TEXTURE TO MATCH EXISTING ADJACENT

WALLS. WALL PAINT TO MATCH WALLS IN ADJACENT LOUNGE.

3. ALL BATHROOM WALLS TO RECEIVE 6" CERAMIC TILE COVE BASE

4. WALL TEXTURE AT SLEEPING AREA TO MATCH EXISTING

5. SLEEPING AREA TO RECEIVE 24"X24" CARPET TILE AND 4" RUBBER WALL BASE TO MATCH EXISTING IN

LOUNGE

6. U.O.N., NEW INTERIOR WALLS SHALL BE FRAMED WITH 24 GA COLD ROLLED STEEL STUD. GC TO VERIFY

THAT WALL CAVITY WILL ACCOMMODATE ANY VENT, WASTE, OR SUPPLY PIPING.

7. MAINTAIN (E) FIRE ALARM SYSTEM AND PROVIDE REQUIRED HORNS, STROBES, MONITORING, AND

PROGRAMMING AS REQ BY BASE FIRE DEPARTMENT.

8. CURRENTLY, THE FACILITY EXPERIENCES WATER HAMMER FOLLOWING TOILET FLUSHING. CONTRACTOR

TO INVESTIGATE AND PROVIDE HAMMER ARRESTOR SIZED PER PDI-WH201 OR PROVIDE OTHER

MITIGATION.

9. CONTRACTOR SHALL SIZE ALL PLUMBING SUPPLY, WASTE, AND VENT LINES PER APPLICABLE UFC AND

DMAFB CPG.

10. CONTRACTOR TO PROVIDE AND INSTALL TOILET ACCESSORIES INCLUDING HAND TOWEL HOOK, TOWEL

HOOK, TP DISPENSER, HAND SOAP DISPENSER, SHOWER ROD AND CURTAIN.

11. INSTALL WALL BACKING AS REQUIRED FOR ALL ACCESSORIES OR WALL MOUNTED EQUIPMENT.

12. AT SHOWER ENCLOSURE, CONTRACTOR SHALL PROVIDE A WATERTIGHT INSTALLATION. DECK MUD

SHALL SLOPE TO DRAIN AND ALL TILE BACKER BOARD JOINTS AND SCREW HOLES SHALL BE TAPED AND MUDDED TO A SMOOTH FINISH. INSTALL LIQUID APPLIED MOISTURE BARRIER (REDGUARD OR APPROVED EQ) TO WALLS UP TO 6" ABOVE SHOWER HEAD AND AT FLOOR DECK. INSTALL PER MANUFACTURER

RECOMMENDATIONS. CONTRACTOR SHALL PERFORM A WATER LEAKAGE TEST PRIOR TO TILE

INSTALLATION.

13. NOTE THAT ALL WALLS SURROUNDING TOILET / SHOWER ROOM ARE TO RECEIVE FULL DEPTH SOUND ATTENUATING BATT INSULATION. WALL CAVITIES WILL BE ACCESSIBLE DUE TO DEMOLITION OF EXISTING

DRYWALL OR BECAUSE OF NEW WALL CONSTRUCTION.

14. PROVIDE REPLACEMENT 100 CFM EXHAUST FANS INCLUDING DUCT WORK TO EXTERIOR OF FACILITY WITH

WEATHER TIGHT LOUVERS FOR ALL THREE BATHROOMS.

DEFINITIONS:

SOSM SINGLE OCCUPANT SLEEPING ROOM

SSQR SHARED SLEEPING QUARTERS RESTROOM

(E)RR

(E)SOSM (E

)L

O U

N G

E

CONCEPTUAL PLAN - NOT FOR CONSTRUCTION

KEY PLAN

SAP ROOM WORK IN THIS AREA

NTS

****ADDITIONAL SCOPE: NOTE THAT THE EXISTING ADA

RESTROOM LOCATED HERE ALSO EXPERIENCES WATER

HAMMER. CONTRACTOR TO REPLACE HAMMER ARRESTOR

SIZED PER PDI-WH201 OR PROVIDE OTHER MITIGATION.

U.S. AIR FORCE

H 5 T5

ND

EINE RNEIV L G

SQIC

A

IR

C O

M B

A T

C O

M M

A N

D

SHEET NO.

D A

V

IS

-M O

N

TH

A N

A

FB

A R

IZ

O

N A

E . M

A D

E R

A S

T, B

LD

G

R E

V

IS

IO

N

S

D A

TE

D

E S

C R

IP

TI

O N

P R

O

JE

C T M

A N

A G

E M

E N

T C

E S

/C E

N M

F B

N V

B

SAP ROOM

FLOOR PLANS

Q U

A R

T E

R S

N

D A

C A

D E

T

R E

N O

V A

T E

A L E

R T A

IR

C

R E

W

A1

(E)SSQR

SSQR DEMO PLAN

Scale: 1/2" = 1'

SSQR FLOOR PLAN

Scale: 1/2" = 1'

RESTROOM WORK IN THIS AREA

DEMO PLAN KEYNOTES

LEGEND

EXISTING WALL OR FURRING TO REMAIN

ITEM TO BE DEMOLISHED

1. (E) WALL TO REMAIN

2. DEMO (E) WALL

3. NOT USED

4. NOT USED

5. NOT USED

6. DASHED LINE INDICATES SECTION OF (E) DRYWALL TO BE REMOVED TO ACCOMMODATE PLUMBING

INSTALLATION AND/OR BE REPLACED WITH MOISTURE RESISTANT DRYWALL, TYP AT ALL WET WALL

LOCATIONS

7. REMOVE SHOWER DRAIN AND ASSOCIATED BRANCH LINE BACK TO (E) 4" MAIN

8. REMOVE (E) TOILET AND ASSOCIATED WASTE LINE BACK TO MAIN. REMOVE WATER HAMMER

ARRESTOR AND ACCESS PANEL

9. REMOVE (E) SHOWER SURROUND AND IN-WALL ROUGH PLUMBING

LEGEND

NEW STEEL STUD FRAMED WALL OR FURRING

EXISTING WALL

FLOOR PLAN KEYNOTES

1. NOT USED

2. NOT USED

3. NEW 60" X 36" X 80" PRE-MANUFACTURED SOLID SURFACE SHOWER PAN AND SURROUND, CONNECT TO

EXISTING DRAIN, INSTALL OVER NEW "REDGUARD" DRAINAGE SYSTEM.

4. (N) SHOWER HEAD AND CONTROLS AT THIS LOCATION. HEAD SHALL BE 7'-0" AFF AND CONTROLS SHALL

BE 3'-6" AFF, CENTERED IN WALL.

5. EXTEND HW AND CW LINES OVERHEAD AND DOWN FURRED WALL TO SUPPLY LOCATION. ROUTE (N)

VENT LINE WITHIN FURRED WALL AND CONNECT ABOVE CEILING TO EXISTING VENT LINE. PROVIDE WALL

CLEANOUT.

6. (N) FLOOR MOUNTED ADA TOILET WITH COMMERCIAL FLUSH VALVE

7. NOT USED

8. NOT USED

9. INSTALL WALL MOUNTED ACCESS PANEL AND WATER HAMMER ARRESTOR OVER TOILET

10. NOT USED

11. NOT USED

(E)SSQR

AutoCAD SHX Text 2'-8"

AutoCAD SHX Text 2'-8"

AutoCAD SHX Text 1'-9"

AutoCAD SHX Text 1'-9"

AutoCAD SHX Text 3"

AutoCAD SHX Text 5'-0"

AutoCAD SHX Text 3'-0"

AutoCAD SHX Text 1'-6"