Attachment 1 - SoudalCaulk.pdf

This information and all further technical advice are based on SOUDAL present knowledge and experience. However, SOUDAL assumes no liability for providing such information and advice including the extent to which such information and advice may relate to existing third party intellectual property rights, especially patent rights. In particular, SOUDAL disclaims all WARRANTIES EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY. SOUDAL SHALL NOT BE RESPONSIBLE FOR CONSEQUENTIAL, INDIRECT OR INCIDENTALDAMAGES (INCLUDING LOSS OF PROFITS) OF ANY KIND. SOUDAL reserves the right to make any changes according to technological progress or further developments.

Distributed by: Soudal, Inc. • Manassas,VA • www.soudalusa.com • info@soudalusa.com • 877-873-8739

Revision: 03/2010

SoudaSeal FC

Base Silyl-terminated polymer

Sag No sag in vertical displ. @120ºF ASTM C 639

Curing system Moisture Cure

Tack-free time 90 min. ASTM C 679 (maximum 72 hrs.)

Cure time 24-72 hrs, ¼” diameter bead @ 75ºF & 50% relative humidity

Hardness – Shore A 50 +/- 5 ASTM C 661

Skin Formation (*) (75°F/50% RH) 5 min.

Service temperature range -40°F to +194°F

Tensile Yield 435 psi ASTM D 412

Elongation 500% ASTM D 412

Total joint movement +/- 20 % ASTM C 719

Stain and color change Passes ASTM C 510 (no visible stain)

Artificial weathering No Cracking ASTM C 793 (2,000 hrs Xenonarc)

Shelf life 12 months Stored between 33ºF & 80ºF

(*) these values may vary depending on environmental factors such as temperature, moisture, and type of substrates

Product:

SoudaSeal Fast Cure is an SMX® adhesive/sealant with high initial tack

Characteristics:

� excellent adhesion on porous and non porous substrates � immediate high grab strength on nearly all surfaces � high performance mechanical properties � flexible elastic rubber - movement accommodation up to +/-

20% � high green strength, quick build-up of end strength, high sheer strength after full cure � no bubble formation within sealant even in high temperature and humidity applications � very easy to tool and finish � color stable and UV resistant � ecological advantages - free of isocyanates, solvents, halogens and acids � minimal health and safety considerations � can be painted with all water based paints and many other systems (to be tested) � good extrudability even at low temperatures � excellent weather resistance in all climates � primerless adhesion on many different substrates (except where water pressure may occur) � almost odorless

Applications:

� can be used for mirror installations as a 1 step product � sealing and bonding in building and construction industry and metal working industry � sanitary and kitchen areas - resists mould growth � structural elastic bonding � structural bonding applications in the automotive industry

(cars, coaches, caravans, marine, trains) � elastic bonding of panels, profiles and other pieces on the most common substrates

Colors:

white, gray, black, concrete gray, beige

Packaging:

10.1 fl. oz. cartridge

Shelf life:

12 months in unopened packaging in a cool and dry storage place at temperatures between 41°F and 77°F

Schedule B B. 1) e.

This information and all further technical advice are based on SOUDAL present knowledge and experience. However, SOUDAL assumes no liability for providing such information and advice including the extent to which such information and advice may relate to existing third party intellectual property rights, especially patent rights. In particular, SOUDAL disclaims all WARRANTIES EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY. SOUDAL SHALL NOT BE RESPONSIBLE FOR CONSEQUENTIAL, INDIRECT OR INCIDENTALDAMAGES (INCLUDING LOSS OF PROFITS) OF ANY KIND. SOUDAL reserves the right to make any changes according to technological progress or further developments.

Distributed by: Soudal, Inc. • Manassas,VA • www.soudalusa.com • info@soudalusa.com • 877-873-8739

Revision 03/2010

SoudaSeal FC

Adhesion:

SoudaSeal FC has an excellent adhesion on almost all substrates. SoudaSeal FC has been tested on the following metal surfaces: steel, AlMgSi1, brass, electrolytic galvanized steel, AlCuMg1, flame galvanized steel, AlMg3 and steel ST1403.

Plastics that were tested include: polystyrene, polycarbonate (Makrolon®), PVC, polyamide, glasfiber reinforced epoxy and polyester (GRP). While producing plastics very often releasing agents, processing aids and other protective agents (like protection foil) are used. These should be removed prior to bonding. For optimum adhesion the use of Surface Activator is recommended. NOTICE: bonding plastics like polycarbonate (ie Makrolon® or Lexan®) in stress loaded applications can give rise to stress cracking and crazing in these substrates. The use of SoudaSeal FC is not recommended in these applications. There is no adhesion on PE, PP, PTFE (Teflon®) and PMMA (ie Plexi® glass).

Substrates:

Type: all usual building surfaces, most metals, polyesters and many plastics. Not suitable for PE, PP, PTFE (Teflon®), ABS or PMMA (ie Plexi® glass).

Surface Preparation: clean, dry, free of dust and grease � it is expected that the product will adhere and perform in uncontaminated joints with most common construction substrates, without the use of a primer

� porous surfaces in water loaded applications should be primed with Primer 150 surface activator may be used to pretreat non-porous surfaces

� we always recommend preliminary compatibility tests pervious to application

Resistance to chemical agents:

Good resistance to water, aliphatic solvents, mineral oils, grease, diluted inorganic acids and alkalis. Poor resistance to aromatic solvents, concentrated acids, chlorinated hydrocarbons.

Remarks:

� Pre-testing for adhesion is intended to eliminate potential filed problems. This testing will aid in determining the proper surface preparation method.

� May be painted, however due to the large number of paints and varnishes available we strongly suggest a compatibility test before application. The drying time of alkyd resin based paints may increase.

� Can be applied to a wide variety of substrates. Due to the fact that specific substrates such as plastics, like polycarbonate, etc. may differ from manufacturer to manufacturer, we recommend preliminary compatibility tests.

� Porous surfaces in water loaded applications should be primed with Primer 150.

� Lower temperatures and humidity will extend curing time.

Bonding Layer:

We recommend a bonding layer of at least ¾” to achieve a bond with maximum elastic properties.

Application:

Method: Manual- or pneumatic caulking gun Application temperature: 34°F to +90°F Cleaning: with IPA immediately after use and before curing Repair with: SoudaSeal FC

Meets:

ASTM C 920, Type S, Grade NS, Class 25, Use T, NT, M, A, G and O, Federal Specification TT-S-00230C, Type II, Class A

Health- and Safety Recommendation:

KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact. On Contact, uncured sealant could cause irritation to skin and eyes. In case of eye contact, flush eyes with warm water for 15 minutes, call a physician. For skin contact, remove sealant with a paper towel. If swallowed, do not induce vomiting, call a physician. SoudaSeal FC is manufactured for professional use only. Refer to Material Safety Data Sheet (MSDS) for further information.

Limited Warranty:

SOUDAL warrants product to be of good quality and will replace or, at our election, refund the purchase price of any products proved to be defective. Satisfactory results depend not only upon quality products, but also upon many factors beyond our control.

Therefore, except for such replacement or refund, SOUDAL

MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR

IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A

PARTICULAR PURPOSE OR MERCHANTABILITY,

RESPECTING ITS PRODUCTS, and SOUDAL shall have no other liability with respect thereto. Any claim regarding product defect must be received in writing one (1) year from the date of shipment. No claim will be considered without such written notice or after the specified time interval. User shall determine the suitability of the products for the intended use and assume all risks and liability in connection therewith.