Attachment 1 - Manual Mill Specifications.pdf
PDF 99 KB Posted
- Attached to
- Model Shop Manual Milling Machines Federal contract opportunity
- Solicitation number
- FA910123QB049
About this file
This document outlines specifications for two manual milling machines to be provided under a solicitation from the Department of the Air Force Materiel Command Test Center. The specifications require the machines to have a minimum spindle speed of 4,200 RPM, spindle taper of R8 collet, power feeds for the quill, X, and Y axes, and accuracy of +/-0.0003 inches. The work tables must have at least 30 inches of X travel, 10 inches of Y travel, and 14 inches of Z travel, along with T-slots and LED lamps. Digital readouts, lubrication systems, and Kurt vises are also required. The successful contractor must provide manuals, test the machines upon delivery, and warrant components for 24 months. Installation, training, and service support within 36 hours for repairs and 48 hours for parts must be maintained after the warranty period. Packaging and delivery to Arnold Air Force Base, along with installation supervision, are included in the cost.
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| Attachment 1 - Manual Mill Specifications Amend 0002.pdf | ||
| FA910123QB049 QandAs.pdf | ||
| Attachment 1 - Manual Mill Specifications Amend 0001.pdf | ||
| FA9101-23-Q-B049 Combined Synopsis Solicitation.pdf | ||
| Attachment 2 -Provisions and Clauses.pdf | ||
| Attachment 3 - Quote Worksheet.docx | DOCX document |
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Draft Specifications for
Manual Mill (Quantity: 2) at
Arnold Air Force Base, TN
Arnold Engineering Development Complex (AEDC)
Provide all materials, labor, and equipment necessary to provide two new fully functional Manual Milling
Machines. Refurbished or remanufactured parts are not authorized for this requirement.
Requirements
• Machining center construction o Ways shall be hardened and ground; preferably chrome dove tails and gibbs.
o Protective way covers for 3-Axis to protect ways and ball screws.
• Headstock Specification o Spindle speed 4,200 Rpm Maximum.
o Spindle drive motor 3HP minimum.
o Spindle taper R8 collet.
o Power feed for quill.
• Work Table o X Travel 30” minimum.
o Y Travel 10” minimum.
o Z Travel 14” minimum.
o Table equipped with standard “T” slots o Power feed X & Y Axis o LED Lamp
• Controls o Digital readout for 2 axis such as Accu-Rite
• Accuracy o Repeatability for X, Y, & Z Axis shall be +/- .0003” o Positioning for X, Y, & Z Axis shall be +/- .0003”/12”
• General o Lubrication system.
o Kurt vise 6”
• Contractor shall provide:
o Machine shall be built to NFPA 79 and operate with AEDC power system which is 480V, 3PH, 60 HZ or quote package should include step down transformer to machine operation voltage.
o Operating Manual, Electrical Manual, maintenance Manual, & Schematics.
o Machine shall include lifting, leveling, and floor attachment hardware.
• Verification
After delivery the Contractor shall test run the machines at the site in accordance with functional tests for accuracy required by ISO/ANSI Standards.
• Warranty o The machines shall be warranted against any defects in material, parts, and workmanship for 24 months after the date of installation. The control, servomotors and main spindle motor are warranted against defects in material, parts, and workmanship for 24 months after the date of installation.
• Maintenance, Parts and Service o The Contractor shall have the capability to service the equipment (labor and parts) beyond the warranty period, or the equipment shall be able to be serviced by a local qualified representative.
The Contractor or representative shall be capable of responding to a repair service call on-site within 36 hours and repair parts delivery within 48 hours after placement of order.
• Packaging/Delivery o Provide all preservation, packaging, and packing to ensure safe delivery of the machines and related components to AEDC (FOB Arnold Air Force Base, TN 37389). Deliver machines to
AEDC for off-loading by AEDC personnel.
• Installation/Training o Installation will be at the Arnold Air Force Base, TN; Arnold Engineering Development
Complex’s Model Shop, West Shop, Building 451. Installation of the machines shall be accomplished by Model Shop personnel and supervised by factory trained servicemen. This service shall be included in machine cost. Installation kit is to be provided in machine cost.
File details come from the government source that posted it. Updated .