attachment-1-bid-29-27-specs.pdf

Four Cylinder, turbocharged, isolation mounted diesel engine and shall be designed and built by the manufacturer

Engine shall be certified to EPA Final Tier 4/EU Stage IV emissions without requiring the use of a DPF

(Diesel Particulate Filter) or EGR (Exhaust Gas Recirculation) aftertreatment components for increased uptime

Engine shall have a individually replaceable, wet-sleeve cylinder liner design to dissipate heat for reduced ring wear and oil breakdown.

Engine displacement shall be no less than 4.5 liters (276 cu. in.)

Engine net peak power (ISO9249) shall be no less than 116 hp (87 kW) @ 1900 rpm

Engine shall develop at least a 26% torque rise and should have at least 339 lb-ft (459 Nm) net torque

@ 1600 rpm

Under-hood engine air cleaner shall be dry type, dual element with evacuator valve, restriction sensor and in-cab restriction warning light

The backhoe shall have a one-piece tilt hood for easy engine access without having to remove engine side shields

Engine shall have no more than 10-micron rated primary fuel filter with water separator

Engine shall have no more than 2-micron rated secondary fuel filter

Engine will be equipped with a water-in-fuel sensor

Engine coolant shall be rated to -40 degrees (-40C)

The backhoe shall be equipped with an oil-to-water engine oil cooler

Unit shall have a coolant recovery tank provided

Unit shall have an electronically-controlled, variable rate suction-type fan with guard for reduced Hp draw, reduced fuel consumption and quieter operation

Foldout, hinged cooling system will allow for efficient clean out. Remote mounted transmission and hydraulic coolers will offer better air exchange and fewer stacked cores.

The hydraulic circuit to be air cooled, the transmission circuit will be water cooled for fast winter warm-up for increased productivity

The transmission shall be a hydraulically actuated powershift with Autoshift control and a torque converter with maximum transport speed of 24.9 mph. Clutch-free; fully synchronized five forward

(automatically shifts between 2nd and 5th gear when Autoshift is engaged), three reverse speeds

The axle will be mechanical -front-wheel-drive (MFWD) with traction control limited-slip differential with electric on/off control

The axle will be sealed with no breather to protect against contamination

The clutch engaged MFWD can be engaged on the fly during operation.

The machine will disengage MFWD in 4th gear to allow for longer life of tires and drive train and reduced fuel consumption

Machine will automatically engage MFWD when brakes are applied for four wheel braking

The transmission shall be isolation mounted to the mainframe to minimize shock load stress

The rear axle shall have a differential lock, electric foot-actuated as standard equipment

The operator can enable a differential lock protection in the monitor, which will not allow the differential lock to be engaged above 1000 rpm to prevent damage to components

The single electric Transmission Control Lever will have gear selection fully integrated in the lever as well as forward, neutral and reverse (FNR power shuttle).

Transmission oil cooler shall be provided as standard equipment

The backhoe shall have hydrostatic power steering with emergency manual mode

The machine will have a dial throttle that will allow the operator to road the machine on cruise control.

Upon engagement of the brake pedal, the engine RPMs return to idle

The final drives shall be heavy-duty outboard planetary distributing loads over four gears sealed in oil bath for long-life and trouble free service.

The front axle shall have remote grease bank for front axle for easy access.

The rear axle bearings shall be self-lubricating and shall not need to be greased

The service brakes shall be inboard, wet-multiple disk, self-adjusting and self equalizing and hydraulically actuated for a long and trouble-free life, sealed from water, mud and dust contamination

Powertrain

Bid specifications for Deere 410 P or similar Backhoe Loader

Engine

Cooling

8/18/2026 and 10:04 AM

Page 1 of 4 #Public

Bid specifications for Deere 410 P or similar Backhoe Loader

The parking brake shall be independent of service brakes, spring applied, hydraulically released, wet multi-disk, self-adjusting and sealed from water, mud and dust contamination.

Park brake when applied shall disengage the transmission and shall not be able to be "driven through" and will automatically apply when engine is shut off.

The hydraulic fittings shall have "O"-ring face seal connectors to secure a tight, leak-free seal

Hydraulic cooler will have an independent reservoir for continuous running of attachments at high ambient outside air temperatures

The hydraulic filter shall be no more than 4 micron and will be vertically mounted, spin on design for ease of installation and leak-free replacement.

Machine shall be equipped with Auto Idle to lower rpm when hydraulics are not active to conserve fuel and reduce noise levels

Machine shall be equipped with Economy Mode with dual feature that can be applied to backhoe or loader functions separately or together for improved fuel economy.

An automatic bucket return-to-dig control will be standard

Hydraulic pump shall be 43 gpm (163L/min.) at 2,200 rpm at 3,625 psi (24 993 kPa) axial piston pump, pressure compensating, load sensing

The backhoe shall have a 12 volt system with 145 amp alternator

Dual 12 Volt Maintance Free Batteries w 360-Min reserve rated capacity ; 1850 CCA W Disconnect & jump posts

The machine shall have blade type, multi-fused circuits

The starter shall have a bypass start safety cover

Cab will be pre-wired for rotating beacon and radio-ready

Unit shall be equipped with 10 LED driving/working lights, (4) front driving/working; (4) rear; (2) side docking lights. The front lights shall be adjustable and the bulbs shall be no less than 32,500 candlepower each.

Unit shall be equipped with LED lights.

‘Machine connectivity to be free from subscriptions or annual renewals that can provide machine data, track utilization, and review diagnostic alerts remotely.

Unit shall be equipped with two front and two rear turn signal/flashing and two rear stop and tail lights and two rear reflectors

Unit shall be equipped with isolation mounted modular design ROPS/FOPS Cab and molded roof

Access to the cab shall be from the right and left side with protected, wide, rigid, self-cleaning steps and ergonomically located hand-holds

3" retractable seat belt shall be provided

Coat hook, built-in beverage holder, operator manual storage compartment, interior rearview mirror and two 12 volt outlets shall be provided

Unit shall be equipped with illuminated electronic gauges with audible warning for: engine coolant temperature, transmission oil temperature and fuel level.

The touch screen monitor system shall have audible and visual warnings: engine air restriction, low alternator voltage, engine oil pressure, hydraulic filter restriction, hydraulic oil temperature, parking brake on/off, and low brake pressure. The seat belt will have a visual warning.

The keyless start will have an electric fuel shut-off and ability to have auto shutdown setup in monitor

Machine will be equipped with a Sealed Switch Module for easy location of controls on the right hand console and increased durability

The touch screen monitor will have a multi-language (English, French and Spanish) digital monitor for diagnostics (including diagnostic messages and fault code readings), calibrations and machine information.

Machine manufacturer will provide a factory installed onboard security system for total machine integration. System will have the ability to accommodate no less than ten operator codes.

Machine shall be enabled with Machine Security, enabled through the monitor.

Unit shall have digital display for: engine rpm, engine hours, system voltage.

The foot throttle shall be suspended

The machine will have a cab w air conditioner & Heater

Machine will have lockable storage on the right-hand side of the cab

Machine will have the lockable storage on the left-hand side of the cab

Hydraulic System

Electrical

Operator Station

Page 2 of 4 #Public

The seat shall be Air Suspension ; heated & vented with fully adjustable armrests and lumbar support.

Vandal protection shall cover the instrument panel. Engine hood, toolbox, hydraulic reservoir, and fuel filler shall be lockable.

The tilt hood shall have two service positions for easy operation

An easy to read periodic maintenance and grease chart shall be easily accessible on the machine.

Fuel tank capacity shall be no less than 34 gallons (128.7 L) and shall be accessible from the ground and lockable. DEF tank to be no less than 3.6 gallons and accessible from ground and lockable.

Operating weight with optional Equipment shall be at least 20,483 lbs

Fluid levels should be easily checked by sight gauges, dipsticks or overflow tank.

Diagnostic Oil Sampling Ports for Engine Oil & Engine Coolant ; Transmission & Hydraulic Oil

The mainframe shall be a one-piece unitized construction for maximum strength

Unit shall have four built-in vehicle tiedowns, two in front and two in rear for safe transport between jobs

The side plate thickness on the loader boom, backhoe boom and mainframe shall be 4.5 mil or greater

Machine shall be equipped with an exterior mounted, ground level accessed and lockable storage compartment

Replaceable, bolt-on rubber bumpers to protect the grille frame for severe loading applications

The backhoe with standard dipperstick digging depth shall be at least 15 ft 11 in (4.85 m)

Machine shall be equipped with a lift mode to increase craning capacity

The boom lift capacity at ground level shall be no less than 4827 lb (2189 kg)

The lift capacity at full height with standard dipperstick shall be no less than 8074 lbs (3662kg) with Lift

Mode

Extendible dipperstick shall extend no less than 4 ft (1.22 m)

Maximum SAE dig depth with extendable dipperstick extended shall be no less than 19ft 8 in. (5.99 m)

The swing lock pin shall be stored in the operator's station

The stabilizer's shall have Heavy duty reversible Stabilizer pads

The backhoe boom design shall be a curved design.

The backhoe boom shall be a power curve design, hourglass shape for maximum strength and optimized visibility to the work tool.

Digging force with standard backhoe, bucket cylinder shall be at least 15,723 lb (69.9 kN)

Backhoe Boom Factory Protection Plate

The machine will be available with factory installed pilot backhoe controls with pattern-selection feature

The swing casting shall have dual yokes: on top and on the bottom

Lift Capacity with 1.5 cu yd (1.0 m³) bucket at full height shall be at least 7,355 lbs

Dump Clearance with bucket at 45 deg. shall be no less than 8 ft 9 in

Digging depth below ground, 1.5 cu yd bucket level shall be no less than 5.3 in.

Bucket breakout force shall be no less than 10,332 lb

The loader shall have hydraulic self-leveling and bucket-level indicator.

The loader shall have divergent loader arms for excellent visibility to the bucket

A single lever with integrated proportional electrohydraulic control of auxiliary loader operation shall be available from the factory when machine is equipped with auxiliary hydraulics. Lever is also equipped with clutch disconnect, momentary MFWD and MFWD on/off.

For truck loading, the loader arms will have a curved-knee design for loading into the center of the truck bed

Loader shall have a single cylinder and linkages for tilt and curl on bucket.

The loader shall have a non-removable, hinged loader boom service lock.

Factory installed Front Hydraulic Coupler

Overall Vehicle

Backhoe

Loader

General Specifications

Page 3 of 4 #Public

Options:

48" Hydraulic Tilt Ditching Bucket w Bolt on Edge & Stucchi Couplers

Factory AM/FM/WB Radio w Bluetooth

Factory Rear Camera System w In Cab 8" Decicated Monitor

Ride Control

Front 340/80R18 & Rear 500/70R24 Radial Mud & Snow Tread Tires

Factory Auxiliary Hydraulics w one & Two Way Flow to Accomadate Thumb & Hydraulic Tilt Bucket

Auxiliary Hydraulics to Accomadate Switching From Thumb to Ditching Bucket from Operators Cab

Factory Backhoe Rear Hydraulic Coupler for Pin-on-Buckets

Factory Hydraulic Thumb That Extends with Extendahoe

Factory Backhoe pin-on 24" Severe Duty Bucket 8.1 CU FT Capacity w 5 TK Teeth

Factory Front Coupler 94" 1.50 CU YD General Purpose Bucket w Reversible Bolt on Edge

4-Coner LED Beacon Lights

Engine Coolant Heater 110Volts (1000 Watts )

Hydraulic Oil for Cold Climates -40F to 104F

Fire Extinguisher Multi-purpose (ABC) Dry Chemical Located in Cab

2-External Cab Rear View Mirrors

Factory HD Front Grill w 2 Bolt on Grill Frame Rubber Bumpers

Backhoe Rear Mounted LED Boom Lights

Cab Pull Down Front Sunshade

Factory MFWD Guard

Factory Stabilzer Cylinder Guards

Factory HD Replaceable Stabilizer Pads

Factory Backhoe Boom Protection Plate

Auto Shift Transmission- Mechanical front Wheel Drive (MFWD) w Limited Slip Differential

Extendible Dipperstick

Page 4 of 4 #Public