Attachment 1- B204 Roof Phase 1.pdf

August 20, 2021

RE: VA 204

To Whom It May Concern:

The above named contractor is currently a Johns Manville Approved Roofing Contractor in good standing. As such, the contractor is eligible to receive Peak Advantage Guarantees for Johns Manville EPDM roofing systems.

These guarantees will be issued to the contractor in accordance with all procedures and requirements of the Johns Manville Peak Advantage Guarantee Program.

Roofing Assembly Products as proposed to Johns Manville Spec # SE6A

Deck Type: Structural Concrete Vapor Barrier: JM Vapor Barrier SA with SA Primer , 1 ply Insulation: ENRGY 3 – 2.6” thickness Insulation: Tapered ENRGY 3 Cover Board: Invinsa Roof Board , 1/4" Membrane: JM EPDM NR 60 mil Flashings: JM EPDM NR 60 mil adhered using JM Membrane Bonding

Adhesive (TPO & EPDM)

Roofing Assembly Attachment

Fastener Type / Adhesive Type

Field Prime Field Perimeter Corner

Vapor Barrier: self-adhered self-adhered self-adhered self-adhered self-adhered All Insulation, 4' x 4':

JM One-Step Foamable, 3/4" bead

Maximum 12" o.c. bead spacing

Maximum 12" o.c. bead spacing

Maximum 6" o.c. bead spacing

Maximum 4" o.c. bead spacing

Cover Board, 4' x 4':

JM One-Step Foamable, 3/4" bead

Maximum 12" o.c. bead spacing

Maximum 12" o.c. bead spacing

Maximum 6" o.c. bead spacing

Maximum 4" o.c. bead spacing

Membrane: JM Membrane Bonding Adhesive

(TPO & EPDM)

Any width sheet

Any width sheet

Any width sheet

Any width sheet

Johns Manville James Nunns Technical Services Rep Roofing Systems Group 10100 W Ute Ave Littleton, CO 80127 800-922-5922 Option 3 Jim.nunns@jm.com

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

Attachement 1 "Phase 1 Product Data Reference"

Perimeter and Corner Dimensions For buildings less than 60 ft in height

Zone 3 (Corners)

• “L” shaped with legs 0.6 times the building height long, and 0.2 times the building height wide

Zone 2 (Perimeters)

• 0.6 times the height of the building

Zone 1 (Field)

• 0.6 times the height of building (note – this brings the inner boundary of field to 1.2 times the height of the building from all edges.

Zone 1’ (Field Prime)

• Any area remaining (note – this zone is not always present depending on building size/shape)

Buildings with continuous parapets 36” or greater may treat corners as perimeters.

Ensure any whole or partial insulation board that falls within the calculated perimeter or corner has the increased securement applied over the entire board. This must also be true for any roof cover/base sheet width when the roll is parallel to the building edge.

All Johns Manville materials installed as listed above are compatible and made in the USA. The system(s) shall be eligible for a 20 year No Dollar Limit (NDL) Johns Manville Peak Advantage Roofing System Guarantee when installed by a certified Johns Manville contractor and inspected and approved by a Johns Manville Technical Representative. All materials supplied or marketed by Johns Manville will be covered under the terms and conditions of this agreement.

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

3 | P a g e

Thank you for your interest in our roofing products and services. Please contact Johns Manville if any information is incomplete or incorrect so that appropriate modifications can be made. If you have any questions, please do not hesitate to contact our technical department at the number below.

Regards, James Nunns Technical Services Rep | Roofing Systems Johns Manville | A Berkshire Hathaway Company 10100 W Ute Ave Littleton, CO, 80127 W: 800-922-5922 Option 3 Ext. 6459 Web: www.jm.com

Johns Manville is a manufacturer of commercial roofing products and offers this general conceptual information to you as a courtesy. This complimentary assistance is not to be used or relied upon by anyone as a substitute for professional engineering design or documentation required by building code, contract or applicable law. By accepting these comments you agree they do not constitute any representations, endorsements of, or an assumption by Johns Manville of any liability for either the adequacy of the design of this building or of any material not supplied by Johns Manville. These comments are for Johns Manville Guarantee purposes only. Additional requirements may be necessary as determined by contract documents, building code and regulations, or governing entity.

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

Attachement 1 "Phase 1 Product Data Reference" http://www.jm.com/ http://www.jm.com/

Product Data

Replace Bldg. 204 Roof Phase 2

Attachement 1 "Phase 1 Product Data Reference"

Jordan Rectangle

JM EPDM NR 60 mil Ethylene Propylene Diene Monomer Membrane

Installation/Application

Mechanically Fastened

Fully AdheredBallasted

Refer to JM EPDM Application Guides and Detail Drawings for instructions.

Packaging and Dimensions

Roll Size Roll

Coverage 10' x 50' (3.05 m x 15.24 m) 500 ft2 (46.5 m2) 10' x 100' (3.05 m x 30.48 m) 1000 ft2 (92.9 m2) 16' 8" x 100' (5.08 m x 30.48 m) 1667 ft2 (154.8 m2) 20' x 50' (6.1 m x 15.24 m) 1000 ft2 (92.9 m2) 20' x 100' (6.1 m x 30.48 m) 2000 ft2 (185.8 m2) 30' x 100' (9.14 m x 30.48 m) 3000 ft2 (278.7 m2) 40' x 100' (12.19 m x 30.48 m) 4000 ft2 (371.9 m2) Extruded in: Milan, OH

Meets the requirements of ASTM D 4637, Type I

Features and Components Membrane: Nonreinforced, cured EPDM (ethylene propylene diene monomer).

Fully Extruded: Produces fewer air voids, more uniform thickness and smoother sheets.

Vulcanization Process: Combines two layers of membrane to produce a fully cross-linked monolithic membrane.

Membrane Formulation: Performs in extreme temperature climates and withstands differential movement (elongation).

UV-Stabilization Properties: Offers outstanding ozone and weather resistance delivering one of the longest service lives available.

Technical Expertise: Backed by 30+ years of EPDM experience and installations.

Energy and the Environment

Property Value Reflectivity* (ASTM C 1549) 0.06 Emissivity* (ASTM C 1371) 0.88 Post-consumer Recycled Content 0% Pre-Consumer Recycled Content 0%

*Test methods for reflectivity and emissivity are LEED®- and CRRC®-approved.

Peak Advantage® Guarantee Information Enhanced guarantees are now available on certain systems for wind and puncture.

Consult your local sales representative for more information and for specific guarantee terms and costs.

Product Guarantee Term When used in most JM EPDM Systems* Up to 20 years

*Contact JM Technical Services for specific systems.

Codes and Approvals

Component

M Membrane

Single Ply

System Compatibility This product may be used as a component in the following systems. Please reference product application for specific installation methods and information.

M ul ti- Pl y BUR APP SBS

Si ng le P ly TPO PVC EPDM

HA CA CA HW HA CA HW SA MF FA MF FA MF FA BA

Do not use with Multi-Ply systems Compatible with the selected Single Ply systems above

Key: HA = Hot Applied CA = Cold Applied HW = Heat Weldable SA = Self Adhered MF = Mechanically Fastened FA = Fully Adhered BA = Ballasted

Color Black

RS-3005 8-17 (Replaces 5-17)

Refer to the Safety Data Sheet and product label prior to using this product.

The Safety Data Sheet is available by calling (800) 922-5922 or on the Web at www.jm.com/roofing.

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

JM EPDM NR 60 mil Ethylene Propylene Diene Monomer Membrane

Tested Physical Properties

Physical Properties

ASTM

Test Method Standard for

ASTM D 4637, Type I JM EPDM – NR 60 mil

St re ng th

Tensile Strength (psi) D 412 > = 1305 1456

Elongation, Ultimate (%) D 412 > = 300 411

Tensile Set (%) D 412 < = 10 0.5

Tear Resistance (lbf/in.) D 624 > = 150 181

Dynamic Puncture Resistance, 5J, Type I D 5635 pass pass

Static Puncture Resistance, 44.1 lbf, Type I D 5602 pass pass

Lo ng ev ity

Overall Sheet Thickness (in.) D 751 +/- 10% pass

Brittleness Point (°F) D 2137 < = -49 pass

Ozone Resistance D 1149 pass pass

Water Absorption (mass %) D 471 < = 8 0.3

He at

A ge d Pe rfo rm an ce

Heat Aged 670 hrs @ 240°F D 573

Tensile Strength (psi) D 412 > = 1205 1450

Elongation, Ultimate (%) D 412 > = 200 403

Tear Resistance (lbf/in.) D 624 > = 125 170

Linear Dimensional Change (%) D 1204 < +/- 1 0.4

W ea th er in g

Pe rfo rm an ce Weathering Resistance, 5040 KJ/(m2-nm) @ 340 nm D 4637 / G 151 / G 155

Visual Inspection – pass pass

Elongation, Ultimate (%) D 412 > = 200 351

Meets the requirements of ASTM D 4637, Type I

RS-3005 8-17 (Replaces 5-17)

Refer to the Safety Data Sheet and product label prior to using this product.

The Safety Data Sheet is available by calling (800) 922-5922 or on the Web at www.jm.com/roofing.

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

Flat & Tapered ENRGY 3

Polyisocyanurate Roof Insulation

Energy and the Environment

LEED® Recycled Content Varies with thickness, see Product Data and Packaging table on next page.

Produced with a pentane blowing agent with zero ozone depletion and virtually no global warming potential.

Peak Advantage® Guarantee Information Systems For use in approved JM Peak Advantage Roofing Guarantees

Codes and Approvals

• FM® Standards 4450/4470 Approvals (refer to FM RoofNavSM)

• UL® Standard 790, 263 and 1256 (refer to UL Roofing Materials system directory)

• Meets the requirements of CAN/ULC S704, Type 2 & 3, Class 3

• California Code of Regulations, Title 24, Insulation Quality

Standard License #TI-1341

• Third-party certification with the PIMA Quality Mark™ for

Long-Term Thermal Resistance (LTTR) values

Installation/Application

Mechanically Fastened

Urethane Adhesive

Hot Asphalt

Refer to the application instructions guidelines for proper utilization of this product.

Flute Span:

Width of Rib Opening: Up to 25/8" Up to 33/8" Up to 43/8" (6.67 cm) (8.57 cm) (11.11 cm) Insulation Thickness (min): 1.0" (2.54 cm) 1.2" (3.05 cm) ≥1.3" (3.30 cm)

Packaging and Dimensions

Flat Sizes 1 4' x 4' (1.22 m x 1.22 m)

4' x 8' (1.22 m x 2.44 m)

Tapered Size 2 4' x 4' (1.22 m x 1.22 m)

Producing Locations Bremen, IN Cornwall, ONT Fernley, NV Hazleton, PA Jacksonville, FL

Stocking Locations 3 Grand Prairie, TX Southgate, CA Tracy, CA

1. For available thicknesses, see Product Data and Packaging table on page 2 of this data sheet. Other sizes available by special request, some sizes are not stocked but can be special ordered with minimum order quantities. Contact your JM Sales Representative for details.

2. Tapered ENRGY 3 and Tapered ENRGY 3 25 PSI are available in thicknesses of 1⁄2" to 4".

Available profiles are shown on page 3 of this data sheet. In some regions extended panels are also available.

3. Not all sizes, thicknesses, and products are stocked at all locations, please call Customer Service at 1-877-766-3295.

RS-5137 5-20 (Replaces 5-19)

Meets the requirements of ASTM C 1289, Type II, Class 1, Grade 2 (20 psi)

• ENRGY 3 / Tapered ENRGY 3

Grade 3 (25 psi)

• ENRGY 3 25 PSI / Tapered ENRGY 3 25 PSI

Features and Components Glass-Reinforced Facers: Provides rigidity and resistance to indentation and crushing, and are compatible with BUR, modified bitumen and single ply membrane systems.

Closed Cell Polyisocyanurate Foam Core: Provides high R-value per inch in built-up, modified bitumen, metal roof and single ply roof systems, and approved for direct application to steel decks.

Component

Type

I Insulation

Multi-Ply Single Ply

Refer to the Safe for Use instructions and product label prior to using this product.

The Safe for Use instructions are available by calling (800) 922-5922 or on the Web at www.jm.com/roofing.

Note: Technical information on this data sheet is intended to be used as a general guideline only and is subject to change without notice. Contact your JM Sales Representative for further details.

Flat

Tapered

HT

High Thermal

TP

Tapered

System Compatibility This product may be used as a component in the following systems. Please reference product application for specific installation methods and information.

M ul ti- Pl y BUR APP SBS

Si ng le P ly TPO PVC EPDM

HA CA HW HA CA HW SA MF MF AD SA IW MF AD IW MF AD BA

Compatible with the selected Multi-Ply systems above Compatible with all Single Ply systems

Key: HA = Hot Applied CA = Cold Applied HW = Heat Weldable SA = Self Adhered MF = Mechanically Fastened IW = Induction Weld BA = Ballasted AD = Adhered

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

Flat ENRGY 3

Polyisocyanurate Roof Insulation

Typical Physical Properties Test ASTM Values

St re ng th Tensile Strength C 209 500 psf (24 kPa) (min), 730 psf (35 kPa) (nom)

Compressive Resistance 10% Consolidation D 1621 Grade 2: 20 psi (138 kPa), Grade 3: 25 psi (172 kPa) (min) Dimensional Stability Change, (length & width) D 2126 0.5% (nom), 2% (max)

M oi st ur e Moisture Vapor Permeance E 96 <1 perm, 57.5 ng/(Pa•s•m2)

Water Absorption C 209 1.0% (max)

In su la tio n Service Temperature D 1623 -100°F – 250°F (-73°C – 121°C) Flame Spread, (foam core) E 84 20 - 30 (nom), 75 (max) Smoke Developed, (foam core) E 84 55 - 250 (nom), 450 (max)

Product Data and Packaging

Thickness Long-Term Thermal Resistance (LTTR) Values 1

Recycled Content 2

20 PSI / 25 PSI

Boards per Pallet Square Feet per Pallet Pallets per Truck 3

in. mm (hr•ft2•°F)/BTU m2•°C/W % Pre-Consumer % Post-Consumer % Total 4x4 and 4x8 4x4 4x8 4x4 4x8

1.0 25.4 5.7 1.00 5.3 / 5.2 31.8 / 29.9 37.1 / 35.1 48 768 1536

48 24

1.1 27.9 6.3 1.10 5.2 / 5.2 30.0 / 28.1 35.3 / 33.3 41 656 1312

1.2 30.5 6.8 1.20 5.2 / 5.2 28.4 / 26.6 33.6 / 31.76 38 608 1216

1.25 31.8 7.1 1.25 5.2 / 5.2 27.7 / 25.8 32.9 / 31.0 35 560 1120

1.3 33.0 7.4 1.30 5.3 / 5.3 27.0 / 25.2 32.3 / 30.4 35 560 1120

1.4 35.6 8.0 1.41 5.3 / 5.2 25.7 / 23.9 31.0 / 29.2 32 512 1024

1.5 38.1 8.6 1.51 5.2 / 5.2 24.5 / 22.8 29.8 /28.0 32 512 1024

1.6 40.6 9.1 1.61 5.2 / 5.2 23.4 / 21.7 28.7 / 27.0 28 448 896

1.7 43.2 9.7 1.71 5.2 / 5.2 22.4 / 20.8 27.7 / 26.0 27 432 864

1.75 44.5 10.0 1.76 5.2 / 5.2 22.0 / 20.4 27.2 / 25.6 27 432 864

1.8 45.7 10.3 1.81 5.2 / 5.2 21.5 / 19.9 26.7 / 25.1 25 400 800

1.9 48.3 10.8 1.91 5.2 / 5.2 20.7 / 19.1 25.9 / 24.3 24 384 768

2.0 50.8 11.4 2.01 5.2 / 5.2 19.9 / 18.4 25.1 / 23.6 24 384 768

2.1 53.3 12.0 2.11 5.2 / 5.2 19.2 / 17.7 24.4 / 22.9 21 336 672

2.2 55.9 12.6 2.22 5.2 / 5.2 18.5 / 17.1 23.7 / 22.3 21 336 672

2.3 58.4 13.2 2.32 5.2 / 5.2 17.9 / 16.5 23.1 / 21.7 20 320 640

2.4 61.0 13.8 2.43 5.2 / 5.2 17.3 / 16.0 22.5 / 21.1 19 304 608

2.5 63.5 14.4 2.53 5.2 / 5.2 16.8 / 15.4 22.0 / 20.6 19 304 608

2.6 66.0 15.0 2.64 5.2 / 5.1 16.3 / 15.0 21.4 / 20.1 18 288 576

2.7 68.6 15.6 2.74 5.2 / 5.1 15.8 / 14.5 21.0 / 19.7 17 272 544

2.8 71.1 16.2 2.85 5.2 / 5.1 15.3 /14.1 20.5 / 19.2 16 256 512

2.9 73.7 16.8 2.96 5.2 / 5.1 14.9 / 13.7 20.1 / 18.8 16 256 512

3.0 76.2 17.4 3.06 5.2 / 5.1 14.5 / 13.3 19.7 / 18.4 16 256 512

3.1 78.7 18.0 3.17 5.1 / 5.1 14.1 / 12.9 19.3 / 18.1 14 224 448

3.2 81.3 18.6 3.28 5.1 / 5.1 13.8 / 12.6 18.9 / 17.7 14 224 448

3.25 82.6 18.9 3.33 5.1 / 5.1 13.6 / 12.4 18.7 / 17.6 14 224 448

3.3 83.8 19.2 3.39 5.1 / 5.1 13.4 / 12.3 18.6 / 17.4 14 224 448

3.4 86.4 19.9 3.50 5.1 / 5.1 13.1 / 12.0 18.2 / 17.1 13 208 416

3.5 88.9 20.5 3.61 5.1 / 5.1 12.8 / 11.7 17.9 / 16.8 13 208 416

3.6 91.4 21.1 3.72 5.1 / 5.1 12.5 / 11.4 17.6 / 16.5 12 192 384

3.7 94.0 21.7 3.82 5.1 / 5.1 12.2 / 11.1 17.3 / 16.3 12 192 384

3.75 95.3 22.0 3.88 5.1 / 5.1 12.0 / 11.0 17.2 / 16.1 12 192 384

3.8 96.5 22.3 3.94 5.1 / 5.1 11.9 / 10.9 17.0 / 16.0 12 192 384

3.9 99.1 23.0 4.05 5.1 / 5.1 11.7 / 10.7 16.8 / 15.8 12 192 384

4.0 101.6 23.6 4.16 5.1 / 5.1 11.4 / 10.4 16.5 / 15.5 12 192 384

4.1 104.0 24.2 4.26 5.1 / 5.1 11.2 / 10.2 16.3 / 15.3 11 176 352

4.2 107.0 24.9 4.39 5.1 / 5.1 10.9 / 10.0 16.0 / 15.1 11 176 352

4.3 109.0 25.5 4.49 5.1 / 5.1 10.7 / 9.8 15.8 / 14.9 11 176 352

4.4 112.0 26.1 4.60 5.1 / 5.1 10.5 / 9.6 15.6 / 14.7 10 160 320

4.5 114.0 26.8 4.72 5.1 / 5.1 10.3 / 9.4 15.4 / 14.5 10 160 320

1. The Long-Term Thermal Resistance (LTTR) values were determined in accordance with CAN/ULC S770 at 75°F (24°C). The ultimate R-Value of these products will depend on individual installation circumstances.

2. Value represents average results (Grade 2/Grade 3). 3. Assumes 48' flatbed truck.

RS-5137 5-20 (Replaces 5-19)

Refer to the Safe for Use instructions and product label prior to using this product.

The Safe for Use instructions are available by calling (800) 922-5922 or on the Web at www.jm.com/roofing.

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

Attachement 1 "Phase 1 Product Data Reference"

Panel Desig. Slope

Dimension LTTR* Value

Nominal Pieces per Unit

Square Foot per Unit Brd Ft per Unit Slope Profiles Thin Thick

1/16 in/ft (5.2 mm/m) 1A 1/16 0.5 0.75 3.6 70 1120 700 1B 1/16 0.75 1 5.0 50 800 700 1 1/16 1 1.25 6.4 38 608 684 2 1/16 1.25 1.5 7.8 32 512 704 3 1/16 1.5 1.75 9.3 28 448 728 4 1/16 1.75 2 10.7 22 352 660 5 1/16 2 2.25 12.1 20 320 680 6 1/16 2.25 2.5 13.6 18 288 684

1/8 in/ft (10.4 mm/m)

AA 1/8 0.5 1 4.3 64 1024 768

A 1/8 1 1.5 7.1 38 608 760 B 1/8 1.5 2 10.0 26 416 728 C 1/8 2 2.5 12.9 20 320 720

D** 1/8 2.5 3 15.9 16 256 704 E** 1/8 3 3.5 18.9 14 224 728 F** 1/8 3.5 4 22.1 12 192 720

FF** 1/8 4 4.5 25.3 10 160 680

R 1/8 0.75 1.25 5.7 44 704 704 S 1/8 1.25 1.75 8.6 30 480 720 T 1/8 1.75 2.25 11.4 22 352 704 U 1/8 2.25 2.75 14.4 16 256 640 V 1/8 2.75 3.25 17.4 14 224 672 W 1/8 3.25 3.75 20.5 12 192 672

3/16 in/ft (15.6 mm/m) J 3/16 1 1.75 7.8 32 512 704 K 3/16 1.75 2.5 12.1 20 320 680

L** 3/16 2.5 3.25 16.6 16 256 736 M** 3/16 3.25 4 21.2 12 192 696

JJ 3/16 0.5 1.25 5.0 52 832 728

KK 3/16 1.25 2 9.3 28 448 728

LL** 3/16 2 2.75 13.6 18 288 691

MM** 3/16 2.75 3.5 18.2 14 224 694

1/4 in/ft (20.8 mm/m) G 1/4 1 2 8.6 30 480 720 H 1/4 2 3 14.4 16 256 640

I** 1/4 3 4 20.5 12 192 672 X 1/4 0.5 1.5 5.7 48 768 768 Y 1/4 1.5 2.5 11.4 24 384 768

Z** 1/4 2.5 3.5 17.4 16 256 768

ZZ** 1/4 3.5 4.5 23.6 12 192 768

3/8 in/ft (31.2 mm/m)

SS 3/8 0.5 2 7.1 36 576 720

TT** 3/8 2 3.5 15.9 16 256 704

1/2 in/ft (41.6 mm/m)

Q 1/2 0.5 2.5 8.6 32 512 768

QQ** 1/2 2.5 4.5 20.5 12 192 672

XX 1/2 1 3 11.4 22 352 704

* (hr•ft2•°F/Btu) ** Extended panels require less adhesive and less labor.

Refer to the Safe for Use instructions and product label prior to using this product.

The Safe for Use instructions are available by calling (800) 922-5922 or on the Web at www.jm.com/roofing.

Johns Manville Tapered Polyiso Offerings Please refer to the previous page for typical physical properties.

0.5” 0.75” 1.0” 1.25” 1.5” 1.75” 2.25” 2.75”2.0” 2.5” 3.0”

1/16 in/ft (5.2 mm/m) Slope

2.0” Filler1A 1B 1 2 3 4 5 6

1A 1B

All Panels Special Order

3.0” Filler

Extended and Special Order Panels: D, E, F, FF

0.5” 1.0” 1.5” 2.0” 2.5” 3.0” 3.5” 4.0” 4.5” 5.0” 5.5”

1/8 in/ft (10.4 mm/m) Slope

4.0” Filler

AA A B C D E F FF

AA A2.0” Filler

AA A

All Panels Special Order

0.75” 1.25” 1.75” 2.25” 2.75” 3.25” 3.75” 4.25” 4.75”

3.0” Filler R S T U V W

R S

3/16 in/ft (15.6 mm/m) Slope

All Panels Special Order

1.0” 1.75” 2.5” 3.25” 4.0” 4.75” 5.5”

J K L M

J K

3.0” Filler

All Panels Special Order

0.5” 1.25” 2.0” 2.75” 3.5” 4.25” 5.0”

JJ KK LL MM

JJ KK

3.0” Filler

1/4 in/ft (20.8 mm/m) Slope

Extended and Special Order Panels: Z, ZZ

0.5” 1.50” 2.5” 3.5” 4.5” 5.5” 6.5”

X Y Z ZZ

X Y

4.0” Filler

All Panels Special Order

X Y 2.0” Filler

1.0” 2.0” 3.0” 4.0” 5.0” 6.0”

G H I

G H

3.0” Filler

3/8 in/ft (31.2 mm/m) Slope

All Panels Special Order

0.5” 2.0” 3.5” 5.0” 6.5”

SS TT

SS TT

3.0” Filler

1/2 in/ft (41.6 mm/m) Slope

Special Order

0.5” 2.5” 4.5” 6.5”

Q QQ

Q 4.0”

Fill

0.5” 2.5” 4.5”

Q Q

2.0”

1.0” 3.0” 5.0”

XX

XX

2.0”

Extended and Special Order Panels: QQ

RS-5137 5-20 (Replaces 5-19)

Tapered Recycle Content:

Recycled content is dependent upon average thickness. To calculate, match the average thickness of Tapered ENRGY 3 to the thickness of Flat ENRGY 3. Use the number from Flat ENRGY 3 as your recycled content.

Tapered ENRGY 3

Polyisocyanurate Roof Insulation

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

INVINSA

ROOF BOARD

High-Density Polyiso Advantage

Refer to the Safety Data Sheet and product label prior to using this product.

The Safety Data Sheet is available by calling (800) 922-5922 or on the Web at www.jm.com/roofing.

Installation/Application

Mechanically Fastened

Urethane Adhesive

Hot Asphalt Cold Applied

Refer to the Application Guides and Detail Drawings for instructions.

Packaging and Dimensions

Sizes 4' x 4' x ¼" (1.22 m x 1.22 m x 6.35 mm)

4' x 8' x ¼" (1.22 m x 2.44 m x 6.35 mm)

Board Weight 6 lb (2.72 kg) 12 lb (5.4 kg) Coverage/Pallet 480 ft2 960 ft2

Boards/Pallet 30 30 Pallet Weight 185 lb (83.5 kg) 370 lb (167 kg) Pallets per Truck* 192 96 Producing Locations Cornwall, ON Jacksonville, FL Fernley, NV

* Assumes 48' flatbed truck.

RS-5500 12-17 (Replaces 11-17)

Features and Components High-Density Polyisocyanurate Foam Core: Closed cell polyisocyanurate foam technology provides additional insulation value, with lightweight and low water absorption characteristics.

Inorganic Coated Glass Facers: (With no cellulose) Provide improved resistance to mold growth, as well as a smooth surface that performs well with self-adhering systems, and efficient adhesive application in fully adhered single ply systems.

Lightweight: Offers labor and installation efficiencies and allows more options for situations where the overall weight is a concern. This also means easy hoisting, staging and maneuvering around the roof.

Flexibility: Means less breakage during handling, and in re-cover applications it allows Invinsa to accommodate minor irregularities in existing roofs.

User Friendly: Invinsa allows easy & efficient scoring, cutting and snapping which permits fast, tight fabrication and all in a low dust environment.

Resistance To Damage: High impact, flexural and compressive strength provides a protective layer for insulation while working with the membrane above to ensure maximum performance and longevity.

Energy and the Environment

LEED® Recycled Content Pre-Consumer: 3.7% Post-Consumer: 0%

Peak Advantage® Guarantee Information Systems Guarantee Term*

When used in most JM multi-ply or single ply systems Up to 30 years

* Contact JM Technical Services for specific systems.

Codes and Approvals

System Compatibility This product may be used as a component in the following systems. Please reference product application for specific installation methods and information.

M ul ti- Pl y BUR APP SBS

Si ng le P ly TPO PVC EPDM

HA CA CA HW HA CA HW SA MF FA MF FA MF FA BA

Compatible with the selected Multi-Ply systems above Compatible with the selected Single Ply systems above

Key: HA = Hot Applied CA = Cold Applied HW = Heat Weldable SA = Self Adhered MF = Mechanically Fastened FA = Fully Adhered BA = Ballasted

Component

Type

PF

Poly Foam

LT

Low Thermal

HD

High Density

B Cover Board

Multi-Ply Single Ply

Meets the requirements of ASTM C 1289, Type II, Class 4, Grades 1, 2 and 3

High Density Polyisocyanurate Foam

Inorganic Coated Glass Facers

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

INVINSA

ROOF BOARD

High-Density Polyiso Advantage

Refer to the Safety Data Sheet and product label prior to using this product.

The Safety Data Sheet is available by calling (800) 922-5922 or on the Web at www.jm.com/roofing.

Typical Physical Properties

Test ASTM Invinsa Roof Board

St re ng th

Compressive Strength, psi (kPa), nom D 1621 150 psi (1,034 kPa)

Flexural Strength Modulus of Rupture, psi (kPa), nom Breakload, lbf (kN), nom

D 1037 1500 psi (10,343 kPa) 25 lbf (0.111 Kn)

Dimensional Stability, % Linear Change, max D 2126 <1%

M oi st ur e

Moisture Vapor Permeance, perm (ng/(Pa•s•m2)), max E 96 <1 perm (<57.5 ng/(Pa•s•m2))

Water Absorption, % by vol, max C 209 <4%

Surface Water Absorption, gram, max C 473 <1 gram

Mold Resistance D 3273 Pass

In st al la tio n

Weight, lb-ft2 (kg-m2), nom N/A 0.375 lb-ft2 (1.83 kg-m2)

Weight per board (4' x 8'), lb (kg), nom N/A 12 lb (5.4 kg) (nom)

Thermal Performance

Thickness in mm

Nominal R-Value (Resistance) (hr•ft2•°F)/BTU m2•°C/W

¼ 6.35 1.2 0.21

RS-5500 12-17 (Replaces 11-17)

Meets the requirements of ASTM C 1289, Type II, Class 4, Grades 1, 2 and 3

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

Tapered Shop Drawing

Replace Bldg. 204 Roof Phase 2

Attachement 1 "Phase 1 Product Data Reference"

4567 123

Sam ple

Label

ForLayering Inform ation)

FillThickness PanelC ode (See

TypicalSection

Panel C ode:

Slope:

P.S.I.:

Size:

D escription:

PanelSchedule:

U sed

As:

Iunderstand thatthe inform ation and dim ensions provided to and used by m ay have been supplied by a third party source.

Therefore,w ith m y signature:

Ihave provided w ith correctfield conditions, including actualfield dim ensions,drain locations,structuralslopes and roofcurb locations,thatm ay alterthe drainage pattern.Therefore,Iacceptthe tapered design show n on this draw ing.

Ihave notm easured the rooforconfirm ed correctfield conditions,including drain locations,structuralslopes and roofcurb locations thatm ay alterthe drainage pattern show n on this draw ing.

H ow ever,Iacceptthis design as show n and take fullresponsibility forany errors,shortages,and/orom issions thatm ay occur.

Please sign below and fax to at

G

EN

ER

AL

N O

TES

SH

O

P D

R

AW

IN

G

APPR

O

VAL

PR

O

JEC

T

IN

FO

R M

ATIO

N

Location:

Q uote

N um ber:

Q uote

Version N um ber(s):

Page:

of

D ate:

Slope:

C ricketSlope:

M in.Thickness:

M ax.Thickness:

Average R

-Value:

Estim ated by:

C ontractor:

Architect:

D raw ing Scale:

Proje :t c

A B

C D

E F

G H

I J

K

LEG

EN

D

Slope D irection R oofD rain

C orresponding

Tapered Panel

TEX

T

R idge

Line

B ase

Layer:

MID- ATLANTIC ROOFING SUPPLY

yl pp uS g nif oo

R cit na lt

A-di

M yl pp uS g nif oo

R cit na lt

A-di

M yl pp uS g nif oo

R cit na lt

A-di

M

-7

7(

1.2.3.4.5.6. The

purpose ofthe is to provide a generalreference fort apered insulation design.Itis the r esponsibility ofthe practicing roofdesign professional usin g these s ervi ces to renderthe ap propriate levelof prof essionaljudgm entnecessary to provide th e appropriate tapered insulation design .

A lljob criteria su ch as dim ensions,drain locations,slope,m inim um starting thicknes s,base layerthickness,average R

-Value,etc.,have been pr ovided by architects ,roofers, e-m ail and faxes to the yl pp uS g nif oo

R cit na lt

A-di

M A llinform ation m us tbe confi rm ed by the roofi ng contractor.Ifany changes are m ade in the job criteria show n below reserves the rightto re -bid the project.

S hop draw ings signed and approved by eitherthe architectorthe roofing contractor m ustbe returned to the priorto fabrication a nd shipm ent ofm aterials.

O nce the m a ter ialis received,the m anufactureris notresponsible forit s safekee ping orshortages discove red.

The roofing contractorm ustverify allm at erialpiece counts w ith packing lists.

All discrepancies m us tbe repor ted im m ediately to

R ecovery boards,bas e sheets,cantstrips,tapered edge strips,crickets orsaddles etc.,notshow n on shop draw i ngs w illbe supplied by others.

t uo ya l f oo r

.c te

.y lp pu S gn if oo R cit na lt A-di M yl pp uS g nif oo

R cit na lt

A-di

M yl pp uS g nif oo

R cit na lt

A-di

M

VA

Building 204 - Em ergency Section1/2”

.50” 6.65”

1/8”

0.5"

1.5"

2.5"

3.5"

4.5"

5.5"

6.5"

7.5"

0.5"

2.5"

4.5"

6.5"

8.5"

10.5"

08/11/2021

1/4”

17.01

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

Accessories

Replace Bldg. 204 Roof Phase 2

Attachement 1 "Phase 1 Product Data Reference"

JM EPDM PEEL & STICK FLASHING

RS-8094 10-15 (Replaces 7-15)

Features and Components

Use: To easily form flashings around corners and penetrations.

Specifically designed for use in areas that cannot be properly detailed with cured EPDM membrane.

Materials: 60 mil (1.52 mm) thick, uncured EPDM with a release liner and a factory laminated, self-adhering EPDM tape.

Color: Black

System Compatibility This product may be used as a component in the following systems. Please reference product application for specific installation methods and information.

M ul ti- Pl y BUR APP SBS

Si ng le P ly TPO PVC EPDM

HA CA CA HW HA CA HW SA MF MF FA MF FA MF FA BA

Do not use in Multi-Ply systems Compatible with the selected Single Ply systems above

Key: HA = Hot Applied CA = Cold Applied HW = Heat Weldable SA = Self Adhered MF = Mechanically Fastened FA = Fully Adhered BA = Ballasted

Installation/Application

Cold AppliedHot Asphalt Hot Air WeldHeat Weld Self-AdheredMechanically Fastened

Liquid-applied

• Prime EPDM membrane with JM Tape Primer or JM Tape Primer (Low VOC) before applying to JM EPDM Peel & Stick Flashing.

• Do not install in direct contact with asphalt or coal tar pitch.

• Refer to JM EPDM applicator guides or detail drawings for instructions.

Packaging and Dimensions

Roll Sizes 6" x 100'

(15.24 cm x

30.48 m)

9" x 50' (22.86 cm x

15.24 m)

12" x 50' (30.48 cm x

15.24 m) Thickness:

Membrane Tape Total

0.060" (1.52 mm) 0.030" (0.76 mm) 0.090" (2.28 mm)

Coverage 50 ft2 (4.65 m2) 37.5 ft2 (3.48 m2) 50 ft2 (4.65 m2) Rolls per Box 2 1 1 Linear ft (m) per Box 200 (60.96) 50 (15.24) 50 (15.24) Wt. per Box lb (kg) 63 (28.6) 24 (10.9) 32 (14.5)

Storage Shelf Life 6 months from manufacture date

Storage Conditions Store indoors, out of direct sunlight, keep clean and dry prior to use.

Temperature Range 60°F – 80°F (16°C – 27°C)

Component

Type

FW

Flashing Wall

FC

Curb/Corner

FP

Penetration

A Accessory

Single Ply

Peak Advantage® Guarantee Information

Systems Approved for use in any JM Peak Advantage Guarantee System

Refer to the Safety Data Sheet and product label prior to using this product.

The Safety Data Sheet is available by calling (800) 922-5922 or on the Web at www.jm.com/roofing.

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

JM EPDM PEEl & Stick inSiDE/OutSiDE cOrnErS

RS-8237 7-15 (Replaces 10-14)

Features and Components

Use: Use universally for either an inside or outside corner.

Quick and easy to install.

Materials: 60 mil (1.52 mm) thick, uncured EPDM (ethylene propylene diene monomer) and a factory laminated, self-adhering EPDM tape.

Color: Black

System Compatibility This product may be used as a component in the following systems. Please reference product application for specific installation methods and information.

M ul ti- Pl y BUR APP SBS

Si ng le P ly TPO PVC EPDM

HA CA CA HW HA CA HW SA MF MF FA MF FA MF FA BA

Do not use in Multi-Ply systems Compatible with the selected Single Ply systems above

Key: HA = Hot Applied CA = Cold Applied HW = Heat Weldable SA = Self Adhered MF = Mechanically Fastened FA = Fully Adhered BA = Ballasted

Peak Advantage® Guarantee Information

Systems Approved for use in any JM Peak Advantage Guarantee System

Installation/Application

Cold AppliedHot Asphalt Hot Air WeldHeat Weld Self-AdheredMechanically Fastened

Liquid-applied

• Prime EPDM membrane with JM Tape Primer or JM Tape Primer (Low VOC) before applying to JM EPDM Peel & Stick Inside/ Outside Corners.

• Do not install in direct contact with asphalt or coal tar pitch.

• Refer to JM EPDM applicator guides or detail drawings for instructions.

Packaging and Dimensions

Size 7" x 9" (17.78 cm x 22.86 cm) Thickness:

Membrane Tape Total

0.060" (1.52 mm) 0.030" (0.76 mm) 0.090" (2.28 mm)

Number per Box 20 Coverage per Box 8.75 ft2 (0.81 m2) Weight per Box 5 lb (2.26 kg)

Storage Shelf Life 6 months from manufacture date

Storage Conditions Store indoors, out of direct sunlight, keep clean and dry prior to use.

Temperature Range 60°F – 80°F (16°C – 27°C)

Component

Type

FC

Curb/Corner

A Accessory

Single Ply

Refer to the Safety Data Sheet and product label prior to using this product.

The Safety Data Sheet is available by calling (800) 922-5922 or on the Web at www.jm.com/roofing.

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

JM EPDM PEEL & STICK T-JOINT PATCHES

RS-8238 10-14 (Replaces 9-13)

Features and Components

Use: To seal seam laps where perimeter and/or header sheets intersect (T-Joints) in EPDM systems.

Materials: 45 mil (1.14 mm), uncured EPDM (ethylene propylene diene monomer) with a factory laminated, self-adhering seam tape.

Color: Black

System Compatibility This product may be used as a component in the following systems. Please reference product application for specific installation methods and information.

M ul ti- Pl y BUR APP SBS

Si ng le P ly TPO PVC EPDM

HA CA CA HW HA CA HW SA MF MF FA MF FA MF FA BA

Do not use in Multi-Ply systems Compatible with the selected Single Ply systems above

Key: HA = Hot Applied CA = Cold Applied HW = Heat Weldable SA = Self Adhered MF = Mechanically Fastened FA = Fully Adhered BA = Ballasted

Peak Advantage® Guarantee Information

Systems Approved for use in any JM Peak Advantage Guarantee System

Installation/Application

Cold AppliedHot Asphalt Hot Air WeldHeat Weld Self-AdheredMechanically Fastened

Liquid-applied

• Prime EPDM membrane with JM Tape Primer or JM Tape Primer (Low VOC) before applying to JM EPDM Peel & Stick T-Joint Patches.

• Do not install in direct contact with asphalt or coal tar pitch.

• Refer to JM EPDM applicator guides or detail drawings for instructions.

Packaging and Dimensions

Size 5.75" (14.61 cm) diameter Thickness Membrane Tape Total

0.045" (1.14 mm) 0.030" (0.76 mm) 0.075" (1.91 mm)

Patches per Box 100 Weight per Box 2 lb (0.9 kg)

Storage Shelf Life 9 months from manufacture date

Storage Conditions Store indoors, out of direct sunlight, keep clean and dry prior to use.

Temperature Range 60°F – 80°F (16°C – 27°C)

Component

Type

MS

Membrane Seaming

A Accessory

Single Ply

Refer to the Safety Data Sheet and product label prior to using this product.

The Safety Data Sheet is available by calling (800) 922-5922 or on the Web at www.jm.com/roofing.

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

JM EPDM SEAM TAPE PLUS

RS-3048 2-19 (Replaces 7-15)

Features and Components

Use: For field seaming JM EPDM membranes. Utilizes a clear polyethylene release liner for ease of installation.

Materials: 3" or 6" (7.62 cm or 15.24 cm) wide, self-adhering, extruded EPDM (ethylene propylene diene monomer) with a clear polyethylene release liner.

Color: Black

Peak Advantage® Guarantee Information

Systems Approved for use in any JM Peak Advantage Guarantee System

Installation/Application

Cold AppliedHot Asphalt Hot Air WeldHeat Weld Self-AdheredMechanically Fastened

Liquid-applied

• Prime EPDM membrane with JM Tape Primer or JM Tape Primer (Low VOC) before applying to JM EPDM Seam Tape Plus.

• Do not install in direct contact with asphalt or coal tar pitch.

• Refer to JM EPDM applicator guides or detail drawings for instructions.

Packaging and Dimensions

Roll Sizes 3" x 100' (7.62 cm x 30.48 m)

6" x 100' (15.24 cm x 30.48 m)

Thickness 0.030" (0.76 mm) Roll Coverage 25 ft2 (2.33 m2) 50 ft2 (4.65 m2) Rolls per Box* 4 2 Linear Units per Box 400 lin ft (121.92 lin m) 200 lin ft (60.96 lin m) Weight per Box 24 lb (10.89 kg) 25 lb (11.34 kg)

*Each box of JM EPDM Seam Tape Plus includes scrubber pads and handle for seam priming.

Storage Shelf Life 18 months from manufacture date

Storage Conditions Store indoors, out of direct sunlight, and keep clean and dry prior to application.

Temperature Range 60°F – 80°F (16°C – 27°C)

Component

Type

MS

Membrane Seaming

A Accessory

Single Ply

Refer to the Safety Data Sheet and product label prior to using this product.

The Safety Data Sheet is available by calling (800) 922-5922 or on the Web at www.jm.com/roofing.

No Photo Available

System Compatibility This product may be used as a component in the following systems. Please reference product application for specific installation methods and information.

M ul ti- Pl y BUR APP SBS

Si ng le P ly TPO PVC EPDM

HA CA HW HA CA HW SA MF MF AD SA IW MF AD IW MF AD BA

Do not use in Multi-Ply systems Compatible with the selected Single Ply systems above

Key: HA = Hot Applied CA = Cold Applied HW = Heat Weldable SA = Self Adhered MF = Mechanically Fastened IW = Induction Weld BA = Ballasted AD = Adhered

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

JM EPDM TAPE PRIMER PLUS

RS-8092 6-20 (Replaces 1-19)

Installation/Application

Scubber Pad

• Do not install in direct contact with asphalt or coal tar pitch.

• Refer to the application instructions guidelines for proper utilization of this primer.

Packaging and Coverage

* Coverage, open and dry time rates can vary dramatically depending on the environmental conditions. Coverage rates stated herein are approximate only.

Storage Shelf Life 12 months from manufacture date

Storage Conditions Clean, dry, indoor environment, out of direct sunlight, in the original unopened container.

Temperature Range 60°F – 80°F (16°C – 27°C) - Protect from freezing

Exposure Window Keep can or pail tightly closed when not in use and protect from moisture contamination. Once exposed to moisture in the air, JM EPDM Tape Primer Plus begins to cure and may gel within 24 hours.

Energy and the Environment

Maximum VOC 685 g/l 1 (EPA Method 24)

1. Exceeds limits in SCAQMD rule 1168

Precautions

Johns Manville EPDM Tape Primer Plus is a combustible material and should be shipped and stored away from open flames, heat or sources of ignition. Keep all pails tightly sealed while in storage. It should be used only in well-ventilated areas. It may cause eye, skin and respiratory irritation, and is harmful or fatal if swallowed. Avoid contact with skin. Use impervious clothing and rubber gloves to avoid prolonged or repeated contact with skin. Read the container label and follow all safety instructions.

System Compatibility This product may be used as a component in the following systems. Please reference product application for specific installation methods and information.

M ul ti- Pl y BUR APP SBS

Si ng le P ly TPO PVC EPDM

HA CA CA HW HA CA HW SA MF AD MF AD MF AD BA

Do not use in Multi-Ply systems Used to prime Membranes in EPDM Single Ply systems

Key: HA = Hot Applied CA = Cold Applied HW = Heat Weldable SA = Self Adhered MF = Mechanically Fastened AD = Adhered BA = Ballasted

Component

Type

PR

Primer

M Membrane

Single Ply

Features and Components

Use: To prime JM EPDM membrane surfaces for adhering JM EPDM Tape and Peel and Stick products.

Type: One-part, solvent-based membrane primer.

Color: Translucent Electric Blue

Features: Tack-Back functionality for detail work in vertical applications and seam work in horizontal applications.

Refer to the Safety Data Sheet and product label prior to using this product.

The Safety Data Sheet is available by calling (800) 922-5922 or on the Web at www.jm.com/roofing.

Container Sizes 4 – 1 gal (3.8 l) cans per box

3 gal (11.4 l) pail

Shipping Weight (approx.) 30 lb (13.6 kg) per box 22 lb (9.8 kg) per pail Containers per Pallet 54 45 Pallets per Truck 24 24

Coverage Rate* (Reinforced) 375 ft2/gal (9.2 m2/l)

(Non-reinforced) 500 ft2/gal (12.3 m2/l)

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

JM MEMBRANE BONDING ADHESIVE

(TPO & EPDM)

RS-7845 2-18 (Replacing 12-17)

Features and Components

Use: For adhering JM TPO and EPDM membranes to approved substrates. Do not use on fleece-backed membranes.

Type: One-part, synthetic polymer-based membrane adhesive, two-sided application.

Substrates: Compatible with insulation boards; metal, wood and other decking materials.

Color: Yellow

Installation/Application

Notched Squeegee

Long Nap Roller

• Ambient Temperature Ranges:

- Apply when ambient temperature is 25°F and rising

- Do NOT apply when dew point is within 10°F or closer to ambient.

• Adhesive Temperature Ranges:

- Adhesive must be greater than 32°F.

- If adhesive falls below 32°F, place back in warm area until temperature is

60°F or greater.

• Do not apply adhesive near seams or splices where a hot-air welder or seam tape will be used.

• Do Not Thin.

Packaging and Coverage Container Size 5 gal (18.9 l) pail Shipping Weight (approx.) 36.5 lb (16.6 kg) Coverage Rate* (2-sided) 50 - 90 ft2/gallon (1.23 - 2.03 m2/l)

* Coverage, open and dry time rates can vary dramatically depending on the particular substrate and environmental conditions. Coverage rates stated herein are approximate only.

If FM Global® or UL® approval is required, consult specific RoofNavSM or the UL Certifications Directory for specific application rates.

Storage Shelf Life 12 months from manufacture date

Storage Conditions Clean, dry, indoor environment in an unopened container

Temperature Range 60°F – 80°F (16°C – 27°C) - Protect from freezing

Energy and the Environment Maximum VOC 660 g/l (EPA Method 24)

Physical Properties

Property JM TPO Membrane

Adhesive (Solvent Based) Weight per Unit (approx.) 7.3 lb/gal (0.87 kg/l) Specific Gravity 0.865 - 0.87

Precautions

This product is flammable. Adhesive contains ingredients which could be harmful if mishandled. Contact with skin and eyes should be avoided, and the recommended personal protective equipment should be worn.

System Compatibility This product may be used as a component in the following systems. Please reference product application for specific installation methods and information.

M ul ti- Pl y BUR APP SBS

Si ng le P ly TPO PVC EPDM

HA CA CA HW HA CA HW SA MF FA MF FA MF FA BA

Do not use in Multi-Ply systems Used to adhere Membranes in the selected Single Ply systems above

Key: HA = Hot Applied CA = Cold Applied HW = Heat Weldable SA = Self Adhered MF = Mechanically Fastened FA = Fully Adhered BA = Ballasted

Component

Type

AD

Adhesive

M Membrane

Single Ply

Refer to the Safety Data Sheet and product label prior to using this product.

The Safety Data Sheet is available by calling (800) 922-5922 or on the Web at www.jm.com/roofing.

Exposure Window Johns Manville recommends immediate and complete use upon opening. Use open containers within 48 hours of opening. Replace lid on can when not in use. Adhesive that has changed color or viscosity is no longer usable.

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

JM ONE-STEP FOAMABLE ADHESIVE

RS-7374 2-19 (Replaces 10-15)

Installation/Application

Bead

• Apply when ambient temperature is 0°F (-18°C) and rising. Do Not Thin.

• Ensure all insulation boards are 4' x 4' (1.22 m x 1.22 m) or smaller.

• Ensure all surfaces are dry and free of any debris, dirt, oil and grease before using JM One-Step Foamable Adhesive.

• Refer to the application instructions and guidelines for proper utilization and coverages rates of this adhesive.

Packaging and Coverage Container Type Case Items per Case/Box 4 cartridges/case with 6 mixing tips Shipping Weight (approx.) 17.8 lb (8.1 kg) Cases/Boxes per Pallet 48

Bead Spacing Typical Coverage Rates* per case ft2/gal gal/100 ft2

12" o.c. 400 to 600 ft2 253 to 379 0.26 to 0.40 6" o.c. 200 to 300 ft2 126 to 190 0.52 to 0.80 4" o.c. 133 to 200 ft2 84 to 126 0.78 to 1.2

* Coverage rates are approximate and may vary based on substrate type and application.

Approved substrates include structural concrete decks, JM Vapor Barrier SA, ENRGY 3, Ret-roPlus, DuraBoard, Invinsa, Securock, DensDeck, DensDeck Prime, smooth modified asphalt membranes and granulated asphalt membranes. Please contact JM Technical Services for other approved substrates.

Storage Shelf Life 12 months from manufacture date

Storage Conditions Clean, dry, well-ventilated indoor environment in an unopened container. 24 hours prior to use, store between 60°F (16°C) and 85°F (29°C).

Temperature Range 45°F to 95°F (7°C to 35°C) - Protect from freezing

Energy and the Environment Maximum VOC 18 g/l as applied after mixing (EPA method 24)

Physical Properties

Property

ASTM

Test Method JM One-Step

Foamable Adhesive

Weight (liquid components)

Part 1 – 9.6 lb/gal (1.5 kg/l) Part 2 – 8.35 lb/gal (1.0 kg/l)

Viscosity (liquid components)

Part 1 – 5,000 cps Part 2 – 3,700 cps

Codes and Approvals

INSULATION ADHESIVE FOR ROOFING

SYSTEMS AS TO EXTERNAL FIRE EXPOSURE.

SEE UL DIRECTORY OF PRODUCTS CERTIFIED

FOR CANADA AND UL ROOFING MATERIALS

AND SYSTEM DIRECTORY. 87P0R10167

Precautions

First Aid – In case of contact with eyes, immediately flush eyes with running water for at least 15 minutes. Call a physician immediately. In case of contact with skin, wash affected area with soap and water. Remove all contaminated clothing and shoes. Wash clothing before reuse and discard contaminated shoes. If swallowed, drink large amounts of water to dilute. If vomiting occurs, drink more water and call a physician immediately.

Environmental Hazard – PMDI in Part 1 component may cause pollution.

Do not discharge into lakes, streams, ponds or public waters. For guidance, contact your regional office of the U.S. Environmental Protection Agency.

Disposal – Neutralize and dispose of spilled material, unused contents and empty containers in accordance with local, state and federal regulations.

Safety – Wear proper clothing and safety equipment.

Features and Components Use: JM One-Step Foamable Adhesive is a two-component polyurethane adhesive used for attaching insulation or cover boards to the roof deck or to other insulation boards.

Type: Two-part, cold application insulation adhesive.

Substrates: Compatible with the following insulations1, cover boards, and substrates: polyisocyanurate; HD wood fiber; perlite;

Invinsa® Roof Board; gypsum; structural concrete; lightweight insulating concrete; treated plywood (5/8" [1.58cm] min. thickness);

cementitious wood fiber plank; base sheets; gypsum; and some existing smooth-surfaced asphalt (per inspection).

1. Ensure that all insulation boards are 4' x 4' or smaller.

Color: Part 1 - Tan, Part 2 - Colorless Features: Solvent free.

Set boards immediately into adhesive; reduces installation time and maximizes adhesive footprint.

No hoses or pumps required.

Always on ratio, eliminates guesswork.

Refer to the Safety Data Sheet and product label prior to using this product.

The Safety Data Sheet is available by calling (800) 922-5922 or on the Web at www.jm.com/roofing.

Component

Type

AD

Adhesive

I Insulation

B Cover Board

Multi-Ply Single Ply

System Compatibility This product may be used as a component in the following systems. Please reference product application for specific installation methods and information.

M ul ti- Pl y BUR APP SBS

Si ng le P ly TPO PVC EPDM

HA CA HW HA CA HW SA MF MF AD SA IW MF AD IW MF AD BA

Used to adhere Insulation in all Multi-Ply systems Used to adhere Insulation in all Single Ply systems

Key: HA = Hot Applied CA = Cold Applied HW = Heat Weldable SA = Self Adhered MF = Mechanically Fastened IW = Induction Weld BA = Ballasted AD = Adhered

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

Installation/Application

Scubber Pad Brush

• Apply product at temperatures above 40° F (4 °C) and rising.

• Do not install JM Single Ply Membrane Primer (Low VOC) in direct contact with asphalt or coal tar pitch.

• Do Not Thin. Refer to the application instructions guidelines for proper utilization of this primer.

Packaging and Coverage Container Sizes 3 gal (11.36 l) pail Shipping Weight (approx.) 30 lb (13.6 kg) Containers per Pallet 75 Coverage Rate* (approx.) 200 ft2/gal (4.9 m2/l)

* Coverage, open and dry time rates can vary dramatically depending on the particular substrate and environmental conditions. Coverage rates stated herein are approximate only.

If FM Global® or UL® approval is required, consult specific RoofNavSM or the UL Certifications Directory for specific application rates.

Storage Shelf Life 12 months from manufacture date

Storage Conditions Clean, dry, indoor environment, out of direct sunlight, in an unopened container

Temperature Range 40°F – 90°F (4.4°C – 32.2°C) - Protect from freezing

Exposure Window Keep can or pail tightly closed when not in use and protect from moisture contamination. Once exposed to moisture in the air, JM Single Ply Membrane Primer begins to cure and may gel within 24 hours.

JM SINGLE PLY MEMBRANE PRIMER

(Low VOC)

RS-3062 12-19 (Replaces 4-15)

Energy and the Environment Maximum VOC <250 g/l (EPA Method 24) This product may be used in jurisdictions limiting VOC (volatile organic compounds) content of single ply roofing adhesive to no greater than 250 g/l.

Physical Properties

Property JM Single Ply Membrane Primer

(Low VOC) Weight per Unit (approx.) 10 lb/gal (1.2 kg/l) Specific Gravity 1.15 - 1.25 Solids 10%

Precautions

Johns Manville Single Ply Membrane Primer (Low VOC) is a flammable material and should be shipped and stored away from open flames, heat or sources of ignition. Keep all pails tightly sealed while in storage. It should be used only in well-ventilated areas. It may cause eye, skin and respiratory irritation, and is harmful or fatal if swallowed. Avoid contact with skin. Use impervious clothing and rubber gloves to avoid prolonged or repeated contact with skin. Read the container label and follow all safety instructions.

System Compatibility This product may be used as a component in the following systems. Please reference product application for specific installation methods and information.

M ul ti- Pl y BUR APP SBS

Si ng le P ly TPO PVC EPDM

HA CA CA HW HA CA HW SA MF FA MF FA MF FA BA

Do not use in Multi-Ply systems Used to prime Membranes in the selected Single Ply systems above

Key: HA = Hot Applied CA = Cold Applied HW = Heat Weldable SA = Self Adhered MF = Mechanically Fastened FA = Fully Adhered BA = Ballasted

Component

Type

PR

Primer

M Membrane

Single Ply

Features and Components

Use: To prime JM EPDM and TPO membrane surfaces for adhering EPDM or TPO peel and stick products.

Type: One-part, low VOC synthetic polymer-based membrane primer.

Color: Clear to Light Yellow

Refer to the Safety Data Sheet and product label prior to using this product.

The Safety Data Sheet is available by calling (800) 922-5922 or on the Web at www.jm.com/roofing.

Project No. 621-21-115 Replace Bldg. 204 Roof Phase 2

Energy and the Environment Maximum VOC 108 g/l (EPA Method 24) This product may be used in jurisdictions limiting VOC (volatile organic compounds) content of single ply roofing adhesive to no greater than 250 g/l.

Physical Properties Property JM Single Ply Sealing Mastic Weight per Unit (approx) 10.42 lb/gal (1.25 kg/l) Specific Gravity 1.45 ButylPolymer/Solids 82% (min) Solvents 18% (max)

Note: Typical values should not be construed as guaranteed analysis of any specific lot or as specification items.

Precautions

Johns Manville Single Ply Sealing Mastic is a combustible material and should be shipped and stored away from open flames, heat or sources of ignition. It should be used only in well-ventilated areas. It may cause eye, skin and respiratory irritation, and is harmful or fatal if swallowed.

Avoid contact with skin. Use impervious clothing and rubber gloves to avoid prolonged or repeated contact with skin. Read the container label and follow all safety instructions.

Installation/Application

Bead

• Apply when the ambient and substrate temperature is 40°F (5°C) and rising.

• Do not use in applications where the caulk is exposed to direct ultraviolet rays.

• Refer to the application instructions guidelines for proper utilization of this sealant.

Packaging and Coverage Container Size Box of twelve 11 oz (325.31 ml) tubes Shipping Weight (approx.) 15 lb (6.8…