Attachment 002 - 11-PD 20013USMC PTU Shirt Draft.pdf

11-PD 20013USMC

(DATE)

INITIAL

DRAFT PURCHASE DESCRIPTION

PT SHIRT: PHYSICAL TRAINING UNIFORM

This Purchase Description is approved for use by the Marine Corps and is available for use by all Departments and Agencies of the Department of Defense.

Prepared by

MARCORSYSCOM

2200 Lester Street

Quantico, VA 22134

Comments, suggestions, or questions on this document should be addressed to Marine Corps Systems Command, 2200 Lester Street, Quantico, VA 22134 ATTN: SEAL-SE-STDS or emailed to

USMC_STDZ_@usmc.mil. .

AMSC N/A FSC 8410

DISTRIBUTION STATEMENT A: Approved for public release. Distribution is unlimited.

11-PD 20013USMC (DRAFT)

1. SCOPE

1.1 Scope. This purchase description covers the requirements for the Physical Training Uniform (PTU) PT Shirt. The PT Shirt is intended for wear by U.S. Marine Corps (USMC) personnel.

1.2 Schedule of sizes. The PT Shirt is furnished in the following size (see 6.2):

Schedule of sizes

Size

XX Small X Small Small Mediu m Large X-Large XX-Large XXX-Large XXXX- Large

2. APPLICABLE DOCUMENTS

2.1 General. The documents listed in this section are specified in sections 3 and 4 of this purchase description. This section does not include documents cited in other sections of this purchase description or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this purchase description, whether or not they are listed.

2.2 Government documents.

2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.

COMMERCIAL ITEM DESCRIPTIONS

A-A-50199 Thread, Polyester Core, Cotton or Polyester-Covered

(Copies of the above documents are available online at https://quicksearch.dla.mil.)

DEPARTMENT OF DEFENSE SPECIFICATIONS

MIL DTL 32075 Label: For Clothing, Equipage, and Tentage

2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.

2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents are those listed in the solicitation or contract (see 6.2).

AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC)

AATCC TM61 Colorfastness to laundering, Home and Commercial: Accelerated https://quicksearch.dla.mil/

AATCC TM135 Dimensional Changes in Automatic Home laundering of Woven and Knit AATCC TM143 Appearance of Apparel and Other Textile End Products after Repeated

Home Laundering AATCC TM150 Dimensional Changes of Garments after Home Laundering

(Copies of the AATCC Technical Manual are available online at http://www.aatcc.org.)

AMERICAN NATIONAL STANDARDS INSTITUTE/AMERICAN SOCIETY FOR QUALITY (ANSI/ASQ)

ANSI/ISEA 107 American National Standard for High-visibility Safety Apparel and

Headwear

(Copies of this document are available online at http://www.asq.org or http://www.ansi.org.)

ASTM INTERNATIONAL

ASTM D204 Standard Test Method for Sewing Threads ASTM D6193 Standard Test Method for Stitches and Seams

(Copies are available online at http://www.astm.org.)

2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.

3. REQUIREMENTS

3.1 First article inspection. When specified (see 6.2), a sample shall be subjected to first article inspection in accordance with the contract or solicitation in accordance with 4.2. The sample size shall be as specified in the procurement document.

3.2 Recycled, recovered, environmentally preferable, or biobased materials. Recycled, recovered, environmentally preferable, or biobased materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs.

3.3 Design. The PT Shirt shall be constructed with knit and have a moisture management system and silver based anti-microbial, Marine Olive Drab (OD) Green 522, and shall have self-fabric raglan short sleeves and neckband. The PT Shirt side panel shall be a mesh knit in black.

3.4 Figures. Figures 1 through 8 are furnished for information purposes only. When inconsistencies exist between the written document and the figures, the written document shall govern.

3.5 Material.

3.5.1 Basic material, PT Shirt. The basic material shall be an elastomeric jersey knit in Marine OD Green 522 for the body and shall have a 1×1 self-fabric for the sleeves and neckband. The cloth shall have a finish with moisture management and silver icon based anti-microbial and shall conform to the Fabric Salient Characteristic Requirements specified in 6.2.

3.5.2 Side panel material, PT Shirt. The side panel material shall be mesh knit in black. The cloth shall have a finish with moisture management and silver icon based anti-microbial and shall conform to the Fabric Salient Characteristic Requirements specified in 6.2.

http://www.aatcc.org/ http://www.asq.org/ http://www.ansi.org/ http://www.astm.org/

3.6 Components.

3.6.1 Thread. The thread shall be polyester core polyester covered, Tex 27 conforming to A-A- 50199 Type II. The finished thread shall have no chemical finishes or treatments other than those commonly used on commercial threads. The thread color shall have a good match to the basic material.

3.6.2 Reflective Material. The photometric performance of the reflective materials shall be tested in accordance with ANSI/ISEA 107 American National Standard for High-Visibility Safety Apparel and Headwear. The performance requirement of the reflective material shall be tested and certified for the Level 2 category. The tests shall include initial photometric measurements prior to test exposure, and photometric measurements after the following test exposures: abrasion, flexing, folding at cold temperatures, temperature variation, and washing. The reflective material shall have a minimum initial level of reflectivity of 300 cd/lux/m2 and have a minimum level of reflectivity of 100 cd/lux/m2 after 50 wash cycles following AATCC TM135 Test Method (1), IV, (A)i specified in Table V. A certificate of compliance will be acceptable for this requirement (see 4.6).

3.6.2.1 Flaking and delamination after launderings. Reflective tapes shall show no signs of flaking, peeling or delaminating after 50 launderings in accordance with AATCC TM135, (1), IV, (A)i specified in Table V. A certificate of compliance shall be acceptable for this requirement (see 4.6).

3.6.2.2 Reflective on front of PT Shirt. The front of the PT Shirt shall have a silver reflective USMC text conforming to the specified dimensions. The USMC text shall be centered horizontally between the center front and the sleeve armhole seam with ±1/4 inch vertical and ±1/4 inch horizontal tolerances. The reflective shall be placed according to the the markers on the pattern. (Figures 1 – 3)

3.6.2.3 Reflective on sleeve of PT Shirt. T he left sleeve of the PT Shirt shall have a silver reflective eagle, globe, and anchor (EGA) conforming to the specified dimensions. The reflective shall be placed according to the the markers on the pattern. (Figure 2 and Figure 4).

3.6.2.4 Reflective on back of PT Shirt. The back of the PT Shirt shall have a silver reflective USMC text and striping conforming to the specified dimensions. The reflective shall be placed according to the markers on the pattern. (Figures 5 – 8)

3.6.3 Labels. Each shirt shall have size and appropriate identification/instruction labels. All labels shall conform to MIL-DTL-32075 and contracting agency requirements. The label shall have good (3.5 or better) colorfastness to laundering when tested in accordance with AATCC TM61 after 5 launderings specified in Table V.

3.6.3.1 Combination size/identification/instruction label. The heat transfer label for the shirt shall conform to MIL-DTL-32075, Type III, Class14. The identification/size/care heat transfer label for Type I shall be placed 1-1/2 inches down from back neckband seam, the label shall be sized from approximately 1-5/8 inches to 2 inches wide and from 2-2/5 inches to 3 inches long, and shall contain the following text for washing instructions:

USMC

MEN’S

MADE IN USA

SIZE

(FIBER CONTENT)

(FIBER CONTENT) SIDE PANELS

TURN INSIDE OUT PRIOR TO

LAUNDERING

MACHINE WASH WARM WITH LIKE

COLORS

DO NOT USE BLEACH

TUMBLE DRY

LOW HEAT

WARNING:

THE USE OF FABRIC SOFTNER

WILL HARM THE MOISTURE

WICKING PROPERTIES OF THIS

GARMENT

3.6.3.2 Barcode label. Each item shall be individually barcoded with a paper tag for personal clothing items. The paper tags shall be standard bleached sulfate that has a basis weight of 100 pounds.

The paper used for the tags shall have a smooth finish to accept thermal transfer and direct printing. The tags shall have a hole and shall be attached to each item by a fastener or the bar code and UPC code tags may be attached as a sticker to the outside of individual poly bag. The tags shall be clearly legible and readable by a scanner. The barcoding element shall be a 13-digit national stock number (NSN).

There shall be a 12-digit UPC number assigned for all NSNs by the contracting activity. The initials UPC must appear beneath the code. The barcode for NSN and UPC type shall be a medium to high density and shall be located so that it is completely visible on the item when it is folded and/or placed on all shipping cartons on which the NSN appears.

3.7 Patterns. Standard patterns that show directional lines, size, and notches for the proper assembling of the parts of the PT Shirt will be furnished by the Government (see 6.2). The standard patterns shall be used as a guide in cutting the manufacturer’s working patterns. The working patterns shall be identical to the Government patterns except that additional notching to facilitate manufacture is permissible. Minor modifications are permitted where necessary to accommodate manufacturer’s processes and the use of automatic equipment. These modifications shall not alter the serviceability, dimensional requirements, or appearance. The patterns provide seam allowances as follows in Table I.

TABLE I. Seam allowances.

Seam Allowance Pattern

3/8 inch For attaching the neckband, raglan sleeves and side seams

3/4 inch For sleeve hem and shirt hem

3.7.1 Pattern parts. The component parts of the PT Shirt shall be cut from materials as specified in accordance with pattern parts indicated in Table II.

TABLE II. List of pattern parts.

Material Pattern Nomenclature CAD Pattern Names Cut Parts A. Basic Material Front PDXXX-FRONT 1

Back PDXXX-BACK 1 Sleeve PDXXX-SLEEVE 2 Neckband PDXXX-NECKBAND 1

B. Mesh Material Side Front PDXXX-SIDE_FRONT 1 Side Back PDXXX-SIDE_BACK 1

3.8 Construction. The stitches per inch specified in Table III shall be interpreted to be the minimum and the maximum stitches per inch. Additional basting and holding stitching to facilitate the manufacture of the shirt shall be permitted, provided the thread used for the additional basting and holding stitching is removed or shall not show on the finished shirt.

3.8.1 Stitches and seams. Seaming and stitch types shall be consistent and exhibit a uniform appearance and shall conform to ASTM D6193. Where two or more seam or stitch types are specified for the same part of an operation, any one of them may be used. Seam allowances shall be maintained with the seams sewn so that no raw edges, run-offs, twists, pleats, puckers, or open seams shall result. All seams shall start and finish evenly. Thread tension shall be maintained so that there shall be no tight or loose stitching. Edge stitching and topstitching shall be uniformly gauged throughout the shirt. The depth between the fold of seams that is required to be worked out shall be less than 1/16 inch. The guides and knives for the overedge machines shall be set to trim only the raveled edges of the fabric and shall not exceed 1/16 inch.

3.8.1.1.1 Repairs of Types 401, 406, 506, stitching. All repairs shall be in accordance with 3.8.1.2.1, except substitute 3/4 inch for 1/2 inch wherever 1/2 inch appears. Repairs to Type 401 stitching may be accomplished by use of Type 301 stitching.

3.8.1.3 Thread breaks and end of seams. The ends of all seams and stitching produced with stitch Type 301, if not caught in other seams and stitching, shall be backtacked not less than 1/4 inch.

The ends of a continuous line of stitching shall overlap no less than 1/2 inch. All thread breaks shall be secured by stitching back of the break not less than 1/2 inch. Skipped stitching and thread breaks in stitch Type 401 may be repaired using stitch Type 301. Pulling or breaking the thread ends is not permitted.

3.8.1.4 Thread ends. All thread ends shall be trimmed to 1/4 inch maximum length.

3.8.2 Automatic stitching. Automatic machines may be used to perform any of the stitch patterns, provided the requirements for the stitch pattern, stitches per inch, and size and type of thread are met;

and at least three overlapping or backstitches are used to secure the ends of the stitching.

3.8.3 Cutting. The parts of the shirt shall be cut in accordance with the patterns specified in 3.7.1 and from the materials and in the quantity specified in Table II.

3.8.4 Appearance of seams. The seams on the finished shirt shall finish smooth and flat and shall have an appearance rating of 4.0 or greater. Puckering on a major portion of a seam that is worse than a rating of 4.0 shall be scored as a puckered seam. The test method for the appearance of seams shall be as specified in Table VI.

3.9 Manufacturing operation requirements. The PT Shirt shall be manufactured in accordance with the manufacturing operation requirements specified in Table III. The contractor is not required to follow the exact sequence of operations. Any basting or holding stitches required to facilitate manufacture are permissible provided the thread is removed or does not show on the finished garments.

Automated apparel equipment may be used to perform any of the operations specified in Table III, providing that the seam and stitch type are as specified and the finished component conforms to the required configuration. Minor modifications are permitted where necessary when using automated equipment. Any modifications shall not alter the dimensional, serviceability, or appearance requirements cited in this purchase description.

3.9.1 Shade and size marking. The component parts of the PT Shirt shall be marked, ticketed, or bundled to ensure a uniform shade and size throughout each shirt. Any method may be used except:

a. Corrosive metal fastening devices.

b. Sew-on type tickets.

c. Adhesive type tickets, which leave an impression or traces of paper adhesive on the material upon removal of the tickets.

d. Any marking medium that would tend to leave a permanent mark.

TABLE III. Stitches and Seams requirements.

Stitch Type

Seam and Stitch Type

Stitch per Inch

401 LSbp-2(B) 10-12 406 EFa-2 10-12 506 SSa-1 8-10

3.10 Finished measurements. The finished measurements for the PT Shirt shall conform to Table IV.

TABLE IV. Finished measurements (inches).

Size 1/2

Chest (A)

1/2 Waist

(B)

1/2 Sweep

(C)

Sleeve Opening

(D)

Front Neck Drop (E)

Back Neck Drop (F)

Sleeve Length

(G)

Center Back

Length (H)

2X-Small 16 15 16-3/4 4-7/8 3-5/8 7/8 13-1/2 25-1/2 X-Small 17-1/2 16-1/2 18-1/4 5-1/2 3-3/4 1 14 26-1/4 Small 19 18 19-3/4 6-1/8 3-7/8 1-1/8

14-1/2

Medium 20-1/2 19-1/2 21-1/4 6-3/4 4 1-1/4

27-3/4

Large 22 21 22-3/4 7-3/8 4-1/8 1-3/8

15-1/2

28-1/2

X-Large 24 23 24-3/4 8-1/4 4-1/4 1-1/2

29-1/4

2X-Large 26 25 26-3/4 9-1/8 4-3/8 1-5/8

Size 1/2

Chest (A)

1/2 Waist

(B)

1/2 Sweep

(C)

Sleeve Opening

(D)

Front Neck Drop (E)

Back Neck Drop (F)

Sleeve Length

(G)

Center Back

Length (H)

16-1/2

3X-Large 28 27 28-1/2 10 4-1/2 1-3/4

30-3/4

4X-Large 30 29 30-1/4 10-7/8 4-5/8 1-7/8 17-1/2 31-1/2

TOLERANCE

±1/2 ±1/2 ±1/2 ±1/4 ±1/4 ±1/4 ±1/4

±1/2

3.10.1 Methods of measurement. The PT Shirt shall be laid smooth and flat, and measured as follows:

(A) 1/2 Chest Measure across from folded edge to folded edge (or side seam to side seam), approximately 1 inch below armhole.

(B) 1/2 Waist At the narrowest area of the waist, measure from folded edge to folded edge.

(C) 1/2 Sweep Measure in a straight line from the bottom of one side seam, across the shirt to the bottom of the opposite side seam.

(D) Sleeve Opening With the short sleeve smooth and flat, measure the bottom hem of the short sleeve from folded edge to folded edge.

(E) Front Neck Drop Measure from imaginary line connecting high point of one shoulder to high point of other shoulder to lowest point at center front at neckband joining seam.

(F) Back Neck Drop Measure from imaginary line connecting high point of one shoulder to high point of other shoulder to lowest point at center back at neckband joining seam.

(G) Short Sleeve Length Measure from neck joining seam at high point shoulder to bottom edge of hem.

(H) Center Back Length Measure from the center back neck, at collar joining seam, down to edge of hem

3.11 Workmanship. The finished PT Shirt shall conform to the quality of product established by this specification. As a final step in the contractor’s production quality control plan before formation of a lot, each PT Shirt shall be examined and laid out flat on a table prior to folding for packaging. A PT Shirt containing a selected defect shall not be included in the end item lot. Selected defects are those defects listed in ANSI/ISEA 107 indicated by an asterisk. The occurrence of defects shall not exceed the applicable point value or defect level.

4. VERIFICATION

4.1 Classification of inspections. The inspection requirements specified herein are classified as follows:

a. First article inspection (see 4.2).

b. Quality conformance inspection (see 4.3).

4.2 First article inspection. The first article sample(s) shall be submitted in accordance with 3.1.

The sample size will be as specified in the procurement document and shall be inspected for compliance with design, configuration, workmanship, and dimensional requirements. The presence of excessive defects, as defined by the contract, or failure to pass any test, shall be cause for rejection of the first article.

4.3 Quality conformance inspection. Conformance inspection shall consist of all examinations and tests specified in this purchase description. Unless otherwise specified, sampling for conformance inspection shall be in accordance with the provisions of ANSI/ISEA 107. The inspection and the AQL shall be as specified in the contract or purchase order.

4.3.1 Component and material inspection. In accordance with 4.2 and 4.3, components and materials shall be inspected in accordance with all the requirements of referenced documents unless otherwise excluded, amended, modified, or qualified in this purchase description or applicable purchase document.

4.3.1.1 Component testing. In addition to any testing required, components listed in Table V shall be tested for the characteristics noted. The methods of testing specified in Table V shall be followed. The lot and sample sizes shall be as follows:

Lot size Sample size 800 or less 2

801 to 22,000 inclusive 3 22,001 or more 5

The lot shall be unacceptable if one or more sample units fail to meet any test requirement specified.

Component Lot size unit Sample unit Thread

Reflective Label

Spool Sheet Piece

3 each thread 1 each design 3 each label

TABLE V. Component tests.

Thread Shrinkage 3.6.1 ASTM D204

Label Colorfastness to Laundering 3.6.3 AATCC TM61, 2A

Reflective Flaking and delamination 3.6.2.1.1 AATCC TM135 (1), IV, (A)i Reflectivity 3.6.2.1 ANSI-107

AATCC TM135 (1), IV, (A)i

4.3.2 In-process inspection. Inspection shall be made at any point or during any phase of the manufacturing process to determine whether construction details that cannot be examined in the finished product are in accordance with specified requirements. This inspection shall include verification that the working patterns conform to the Government patterns in all respects. Whenever any nonconformance is

Component Characteristic Requirement Test Method noted, corrections shall be made to the affected items and lot in-process. Items that cannot be corrected shall be removed from production.

4.3.3 End item testing. The appearance rating of the seams and stitching of the finished PT Shirt shall be examined in accordance with Table VI and shall have a rating of 4.0 or greater after five launderings. This requirement shall be applicable to all seams including the collar, armholes, side and underarm seams, and sleeve hem.

TABLE VI. End item testing.

Characteristic Requirement Test Method

Seam Appearance 4.3.3 AATCC TM143 (1), IV, (A)i Reflective durability after 50 washes (flaking and delaminating)

4.3.4 AATCC TM150 (1), IV, (A)i

Dimensional stability after 3 launderings 4.3.5.1 AATCC TM150 (1), IV, (A)i

4.3.4 Reflective durability requirements. After application of the symbols on the garments, an additional test shall be performed to ensure proper application of the transfers. The garments shall be washed at a water temperature of 120 degrees Fahrenheit with a mild detergent for fifty cycles with the machine set on a normal/cotton sturdy cycle. Three samples of each garment shall be tested in accordance with AATCC TM150 (1), IV, (A)i. A visual inspection shall be performed after 50 cycles.

There shall be no evidence of flaking, peeling or delaminating. A certificate of compliance will be acceptable for this requirement (see 4.6).

4.3.5 End item dimensional inspection. In accordance with 3.10, finished PT Shirts shall meet the measurements in Table IV when measured as specified in 3.10.1. The occurrence of defects shall not exceed the applicable point value limit specified in purchase order or contract.

4.3.5.1 End item dimensional stability after laundering. End item shall not shrink or extend more than 5 percent in length after 3 launderings in accordance with AATCC TM150 (1), VI, (A)i. One garment each size from a regular length shall be tested.

4.4 End item visual examination. Each PT Shirt shall be examined for the defects listed below (see Table VII).

TABLE VII. End item visual examination.

Material Defects and Damages Major Minor A

Minor B

a. Any hole, cut, tear, mend, drop stitch, loose knit, miss knit, slub, streak, or knitted-in waste *

b. Abrasion damaging the fabric *

c. Any broken yarns *

d. Any vertical runs *

e. Needle chew that might develop into hole *

f. Scissor or knife cut, tear, mend, pull, snag, or burn *

Shaded Part

Material Defects and Damages Major Minor A

Minor B

a. Shade varying within a part or between two or more parts on outside of garment *

b. Color not as specified X

Cleanliness

a. Any spot or stain clearly noticeable on outside of PT Shirt X

b. Any spot or stain clearly noticeable on inside of PT Shirt X

c. Thread ends not trimmed throughout major portion of PT Shirt or two or more markings not removed

X

Components

a. Any component part omitted, damaged, full, tight, or twisted *

b. Any component part off-grain *

Cutting/ Sewing

a. Raw edges, open seams X

b. Distorted parts or poor workmanship X

c. Any part of garment caught in unrelated operation or stitching X

Seams and Stitching

a. Loose or tight tension resulting in loose or tight seams X

b. Any seam puckered, distorted, pleated, irregular or open *

c. Distorted pleated, or irregular seams required to be forced out and having a depth between the fold of 1/8 inch or more X

d. Irregular seams required to be forced out and having a depth between the fold of 1/8 inch or more X

e. Unsecured seams or stitching (not backstitched at least 1/2-inch) or caught in a cross seam X

f. Any line of stitching omitted or misplaced X

g. Thread breaks stitched less than 1/2 inch beyond each end of break

X

h. Seam allowance not as specified, raw edge adversely impacting appearance or serviceability X

i. Topstitching not finishing as specified X

j. Junction of seams not meeting within 1/4 inch X

Reflective Heat Transfers

a. Heat transfer USMC symbol applied incorrectly *

b. Heat transfer USMC symbol placement not as specified *

c. USMC symbol or text peeling *

Labels

Material Defects and Damages Major Minor A

Minor B

a. Label missing, incorrect, or illegible X

b. Label positioned or attached incorrectly X

c. Heat transfer Label applied incorrectly *

d. Heat transfer Label placement not as specified *

e. Label text peeling *

Dimensions

a. Measurement of item not as specified *

b. Sleeves more than 1/2 inch different when compared to each other

X

Bar Codes and Packaging

a. Bar code or UPC code omitted or not readable by scanner

b. Human-readable interpretation (HRI) omitted or illegible

c. Bar code not visible on folded, packaged item

d. Bar code causes damage to the item

e. Any items not packaged in accordance with the contract or purchase order

4.5 Responsibility for compliance. All items shall meet all requirements of sections 3 and 4. The inspection set forth in this document shall become part of the contractor’s overall inspection system or quality program. The absence of any inspection requirements in this document shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material.

4.6 Certificate of compliance. When certificates of compliance are submitted, they shall contain verifiable actual test and inspection data. The Government reserves the right to inspect and test the material or components to verify the validity of the certification.

5. PACKAGING

5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house Contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Point’s packaging activities within the Military Service or Defense Agency or within the Military Service’s system commands. Packaging data retrieval is available from the managing Military Department’s or Defense Agency’s automated packaging files, CD-ROM products, or by contacting the responsible packaging activity.

6. NOTES

(This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.)

6.1 Intended use. The PT Shirt is intended to be worn by military personnel of the USMC.

6.2 Acquisition requirements. Acquisition documents must specify the following:

a. Title, number, and date of this purchase description.

b. Types, sizes, and lengths required (see 1.2 and 1.3).

c. Quantity required.

d. When a first article sample is required (see 3.1).

e. Packaging requirements (see 5.1).

f. Issue of individual documents referenced (see 2.2 and 2.3).

g. Conformance inspection and Acceptable Quality Limits (AQL) (see 4.3).

h. Fabric salient characteristics (Table 1 in the Physical Training Uniform SOW).

i. Guidance on size, confirmation of placement of graphics

j. Government Standard patterns (see 3.7).

6.3 Subject term (key word) listing.

PT Shirt

PTU

FIGURE 1. PT Shirt front view.

FIGURE 2. PT Shirt Reflective Placement - Front.

FIGURE 3. USMC Logo Front Chest heat transfer graphic.

FIGURE 4. EGA heat transfer graphic for sleeves

FIGURE 5. PT Shirt back view.

FIGURE 6. PT Shirt Reflective Placement - Back.

FIGURE 7. PT Shirt Reflective Striping Heat Transfer Graphic - Back.

FIGURE 8. PT Shirt, USMC text center back heat transfer graphic.

Custodial: Preparing activity:

Navy – MC Navy – MC

Review activities:

Navy – MC

DLA – CT