ASBESTOS_REPORT.pdf

P.O. Box 13216 Lansing, MI 48901 Phone: 888.449.4566 Fax: 888.448.8739 www.redcedarconsulting.net

October 7, 2025

Mr. Brian Taylor City of Jackson Community Development Department Jackson, MI 49202

RE: Asbestos Containing Material and Hazardous Materials Inspection 521 Wildwood Ave. Jackson, MI 49201 Parcel ID: 521 Wildwood Ave.

Dear Mr. Taylor:

Red Cedar Consulting has completed an asbestos-containing material (ACM) and hazardous materials inspection at 521 Wildwood Ave. Jackson, Michigan (Subject Property). This inspection was completed at the request of the City of Jackson to comply with the United States Environmental Protection Agency (USEPA) requirements for demolition and renovation set forth under the National Emissions Standards for Hazardous Air Pollutants (NESHAP, 40 CFR Part 61). This inspection was also completed to comply with the Occupational Safety and Health Administration (OSHA) Asbestos Standards for Construction (29 CFR 1926.1101) which limits employee exposure to asbestos.

SUBJECT PROPERTY

The Subject Property is comprised of a 0.38-acre residential parcel which contains an approximate 4,947 square foot residential building (the Building) constructed in 1900. The Building was constructed on a concrete basement with two aboveground floors. The exterior walls of the Building were finished with brick while the roof was sealed with asphalt shingles. The Building can be further divided into a living room, dining room, kitchen, a parlor, five bedrooms and two bathrooms on the first floor while the second floor contains six bedrooms and two bathrooms.

VISUAL INSPECTION AND SAMPLING

Asbestos Containing Materials Inspection

Darrell DeMaster of Red Cedar Consulting (Red Cedar), accredited State Of Michigan/EPA Asbestos Building Inspector (Accreditation Number A31159) who completed training per the Michigan Asbestos Workers Accreditation Act 440, completed an inspection of the Subject Property on August 29, and September 10, 2025, for suspected asbestos containing building materials.

Project No.: 12-1027

This inspection, and subsequent sample collection was completed in accordance with the USEPA Asbestos Hazard Emergency Response Act (AHERA) (40 CFR Part 763) assessment and sampling protocol.

During the completion of the inspection, each area of the Subject Property was visually inspected for asbestos containing building materials (ACBM). Following the completion of the visual inspection, Red Cedar staff identified each suspect area of friable and non-friable ACBM and sorted them into one of three homogenous categories for sampling purposes. AHERA defines friable as a material that when dry, may be crumbled, pulverized, or reduced to powder by hand pressure. A homogenous area is defined by OSHA as an area of surfacing, thermal system insulation (TSI) or miscellaneous material that is uniform in color and texture. Surfacing materials are most commonly found in sprayed-on, troweled-on or otherwise applied to surfaces, such as acoustical plaster on ceilings and fireproofing materials on structural members. TSI refers to materials applied to pipes, fittings, boilers, ductwork, or other components to prevent heat loss or gain, or condensation. Any material that does not fall under the surfacing or TSI category, such as floor tile, drywall, and acoustical ceiling tile are placed into the miscellaneous materials category.

Following the completion of the visual inspection, Red Cedar staff identified the following materials as suspect ACBM:

• Asphalt Shingle

• Drywall and Joint Compound

• Linoleum

• 12”x12” Vinyl Floor Tile

• Flashing

• Cement Board

• Plaster

• Textured Surfacing

Red Cedar staff collected thirty-eight samples of suspect ACBM separated into sixteen distinct homogenous groups for laboratory analysis. Samples were collected and submitted to APEX Research Inc. Laboratories (APEX) (Accreditation Number 102118-0) for laboratory analysis. Analysis was completed utilizing polarized light microscopy (PLM) which is the Environmental Protection Agency (EPA) approved method for analysis of bulk materials for asbestos. PLM analysis completed pursuant to method (EPA 600/M4-82-020) identifies asbestos fiber bundles by the visual properties displayed when the sample is treated with various dispersion staining liquids. The laboratory report completed following the sample analysis indicates if asbestos is present, and at what percentage along with a description and percentage of other fibrous and non-fibrous materials and sample color. Chain-of-custody documentation was followed from sample collection through shipping and receiving of the samples at the designated laboratory. The documentation assures that samples will meet the quality assurance/quality control measures defined by AHERA. The laboratory analytical report prepared by APEX for the thirty-eight samples is included as Attachment A.

Hazardous Materials Inspection

On August 29 and September 10, 2025 the Subject Property was also inspected for the presence of hazardous materials which include but are not limited to polychlorinated biphenyls (PCBs) and potential mercury containing equipment and any items or containers that may contain or be classified as a hazardous or regulated material. Each material, if identified, was documented along with the approximate location. Any materials identified as hazardous are included in Table 1.

INSPECTION RESULTS AND RECOMMENDATIONS

During the completion of the asbestos inspection, thirty-eight samples of suspect ACM were collected and are documented in Table 2 along with the Red Cedar sample number, description, friability, material type, ACM classification, sample location, material quantity and laboratory analytical results. A Site Diagram was prepared which provides the general building layout and sample locations and is included as Attachment B.

ACM, as defined by the USEPA NESHAP is “any material containing more than 1 percent asbestos as determined using the method specified in appendix E, subpart E, 40 CFR part 763 Section 1, Polarized Light Microscopy”.

Friable ACM is defined by NESHAP as any material containing more than 1 percent asbestos that, when dry, can be crumbled, pulverized, or reduced to powder by hand pressure. Friable ACM is a concern due to the ease of unintentionally disturbing the ACM which may result in “visible emissions” which is known as a Fiber Release Episode.

Non-friable asbestos-containing material is defined as “material containing more than 1 percent asbestos that, when dry, cannot be crumbled, pulverized, or reduced to powder by hand pressure. Non-friable ACMs are separated into Category I and Category II ACM. Category I ACM is any asbestos containing packing’s, gaskets, resilient floor coverings (vinyl floor tile and linoleum are examples of these) and asphalt roofing products. Category II ACM is stated by NESHAP as any material excluding Category I non-friable ACM such as drywall, plaster or fiberboard insulation.

Presumed Asbestos Containing Material

Presumed Asbestos Containing Materials (PACM) are suspect surfacing, TSI and miscellaneous materials found in buildings constructed prior to 1980 which are classified as and due to the age of the structure, are assumed to be ACM and do not require sample collection and analysis. OSHA dictates that PACM may be “rebutted” following a complete inspection pursuant to AHERA protocol.

The HVAC Duct Wrap and Air-O-Cell Pipe Wrap located in the Building was classified as PACM due to the age of the structure and samples were not collected.

Table 3 lists the location, material description, friability, condition, material type (surfacing, thermal or miscellaneous) and approximate quantity of all PACM documented at the Subject Property.

Table 4 provides a summary of all ACM documented at the Subject Property which includes the material location, description, and approximate quantity.

Friable ACM’s

HVAC Duct Wrap and Air-O-Cell Pipe Wrap identified in the Building in conjunction with the heating systems are classified as friable ACM. The visual assessment to quantify the extent of this material identified Friable ACM at the following locations within the basement, first and second floors:

• Basement (HVAC Wrapped Ductwork, 50 lin. ft.)

• Basement Crawl Space Misc. debris and clean-up (Air-O-Cell, 200 sq. ft.)

Category I ACM

Five types of resilient floor covering were found within the Building and were found to contain up to 10% Chrysotile asbestos. The assessment to quantify the extent of this material identified approximately 1,104

sq. ft. of this material within the Building. The locations and quantities of the different types of floorings are listed below:

• Beige Linoleum, Dining (468 sq. ft.)

• 12”x12” Red Vinyl Floor Tile, Bedroom 1 (168 sq. ft.)

• 12”x12” Red Medallion Vinyl Floor Tile, 2nd Fl. Bedroom 1 (156 sq. ft.)

• 12”x12” Brown and Gray Vinyl Floor Tile, 2nd Fl. Bedroom 4 (156 sq. ft.)

• Multilayered Gray Linoleum, 2nd Fl. Bathroom 2 (156 sq. ft.)

Asphalt roof samples with tar collected during the completion of the inspection were found to contain up to 10% Chrysotile asbestos. The assessment to quantify the extent of this material identified 100 sq. ft. of asphalt roofing materials with tar on the Building.

Roof Flashing samples collected during the completion of the inspection were found to contain up to 10% Chrysotile asbestos. The assessment to quantify the extent of this material identified 30 lin. ft. of roof flashing materials on the Building.

Category II ACM

No Category II non-friable ACM was identified during the completion of this inspection.

RECOMMENDATIONS

Asbestos Containing Materials

HVAC material identified in the Building system and listed below is classified as friable ACM and should be removed prior to any renovation/demolition activities.

• Basement (HVAC Wrapped Ductwork, 50 lin. ft.)

• Basement Crawl Space Misc. debris and clean-up (Air-O-Cell, 200 sq. ft.)

The Category I roofing materials and resilient floor coverings are non-friable ACM’s that should be abated to mitigate any future exposure.

Please note: The location of samples obtained during this inspection were in a random fashion and areas that were not identified during this inspection may be damaged or have become damaged since the inspection was completed. If Category I or Category II friable materials are discovered prior to or during the demolition/renovation process, these materials must be abated prior to commencement of any demolition/renovation activities at the Subject Property.

Hazardous Materials

Hazardous Materials identified at the Subject Property and documented in Table 1 which require proper removal and disposal consist of the following items:

• No Hazardous Materials Identified

REGULATORY REQUIREMENTS

A Notification of intent to Renovate/Demolish form must be filed with the Michigan Department of Environmental Quality- Air Quality Division at least 10 working days prior to any renovation or demolition activities at a site.

The Notification of Intent to Renovate/Demolish form must also be completed and submitted to the MIOSHA-Asbestos Program whenever demolition, encapsulation and/or renovation activities at a site involving greater than ten lineal feet and/or fifteen square feet of ACM will be completed.

Regulated asbestos containing materials per NESHAP (40 CFR Part 61) which falls into any of the following categories are ACM’s that must be removed prior to any renovation/demolition activities at the Subject Property.

• Friable asbestos material.

• Category I non-friable ACM that has become friable.

• Category I non-friable ACM that will be or has been subjected to sanding, grinding, cutting, or abrading.

• Category II non-friable ACM that has a high probability of becoming or has become crumbled, pulverized, or reduced to powder by the forces expected to act on the material in the course of renovation or demolition operations.

Asbestos abatement should only be performed by a certified asbestos abatement contractor licensed to complete abatement work. The contractor must also follow the standards and requirements set forth per the OSHA Asbestos Standards for Construction (29 CFR 1926.1101) and the USEPA NESHAP (40 CFR Part 61).

Additional information regarding the OSHA Asbestos Standards for Construction (29 CFR 1926.1101) and the USEPA NESHAP (40 CFR Part 61) can be obtained by contacting the associated agency below.

NESHAP Asbestos Program MIOSHA-CSHD-Asbestos Program Department of Environmental Quality State of Michigan Phone: 517-284-6777 Phone: 517-284-7680 Email: asbestos@michigan.gov

DISCLAIMER

Red Cedar Consulting performed destructive testing methods in an attempt to access and inspect all areas of the Building. Unfortunately, due to the age of construction along with multiple additions/renovations that may have been completed on the Building, additional inspections may be required if suspect ACM material not documented within this report is encountered during renovation/demolition activities.

This report was prepared at the request and for exclusive use by the City of Jackson and may not be reproduced or sold without written permission from Red Cedar Consulting.

We appreciate the opportunity to provide the requested services. Please contact us at (888) 449-4566 with any questions or concerns.

Sincerely, Red Cedar Consulting

Aaron Paquet

Michigan/EPA Certified Asbestos Building Inspector (A30955)

©2025 Red Cedar Consulting, LLC.

Attachment A

APEX Research Laboratory Analytical Results

Certificate of Laboratory Analysis Test Method, Polarized Light Microscopy (PLM)

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 01 Asbestos Present: NO Cellulose - 40%

Cust. #: WA-HM-01A No Asbestos Observed Other - 60% Material: Brown Shingle Location:

Appearance: black,fibrous,homogenous Layer: 1 of 1

Lab ID #: 119620 - 02 Asbestos Present: NO Cellulose - 40% Cust. #: WA-HM-01B No Asbestos Observed Other - 60% Material: Brown Shingle Location:

Appearance: black,fibrous,homogenous Layer: 1 of 1

Lab ID #: 119620 - 03 Asbestos Present: NO Cellulose - 20% Cust. #: WA-HM-02A No Asbestos Observed Other - 80% Material: Drywall Location:

Appearance: white,fibrous,nonhomogenous Layer: 1 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. Liability limited to cost of analysis.

Project: 521 Wildwood Ave.

NVLAP Lab Code 102118-0

APEX Research Inc., 7717 Kensington Ct., Brighton, MI 48116

(734) 449-9990, Fax (734) 449-9991 Page 1 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 03a Asbestos Present: NO Other - 100%

Cust. #: WA-HM-02A No Asbestos Observed Material: Joint Compound Location:

Appearance: white,nonfibrous,homogenous Layer: 2 of 2

Lab ID #: 119620 - 04 Asbestos Present: NO Cellulose - 20% Cust. #: WA-HM-02B No Asbestos Observed Other - 80% Material: Drywall Location:

Appearance: white,fibrous,nonhomogenous Layer: 1 of 2

Lab ID #: 119620 - 04a Asbestos Present: NO Other - 100% Cust. #: WA-HM-02B No Asbestos Observed Material: Joint Compound Location:

Appearance: white,nonfibrous,homogenous Layer: 2 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 2 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 05 Asbestos Present: YES Other - 90%

Cust. #: WA-HM-03A Chrysotile - 10% Material: Beige Linoleum Location:

Appearance: beige,fibrous,nonhomogenous Layer: 1 of 1

Lab ID #: 119620 - 06 Asbestos Present:

Cust. #: WA-HM-03B Material: Beige Linoleum Location: NOT ANALYZED Appearance:

Layer: 1 of 1

Lab ID #: 119620 - 07 Asbestos Present: YES Other - 95% Cust. #: WA-HM-04A Chrysotile - 5% Material: 12x12 Red Vinyl Floor Tile Location:

Appearance: red,fibrous,homogenous Layer: 1 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 3 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 07a Asbestos Present: NO Other - 100%

Cust. #: WA-HM-04A No Asbestos Observed Material: Glue Location:

Appearance: yellow,nonfibrous,homogenous Layer: 2 of 2

Lab ID #: 119620 - 08 Asbestos Present:

Cust. #: WA-HM-04B Material: 12x12 Red Vinyl Floor Tile Location: NOT ANALYZED Appearance:

Layer: 1 of 2

Lab ID #: 119620 - 08a Asbestos Present: NO Other - 100% Cust. #: WA-HM-04B No Asbestos Observed Material: Glue Location:

Appearance: yellow,nonfibrous,homogenous Layer: 2 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 4 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 09 Asbestos Present: NO Cellulose - 5%

Cust. #: WA-HM-05A No Asbestos Observed Fiberglass - 10% Material: Tan 9" Square Linoleum Other - 85% Location:

Appearance: beige,fibrous,nonhomogenous Layer: 1 of 1

Lab ID #: 119620 - 10 Asbestos Present: NO Cellulose - 5% Cust. #: WA-HM-05B No Asbestos Observed Fiberglass - 10% Material: Tan 9" Square Linoleum Other - 85% Location:

Appearance: beige,fibrous,nonhomogenous Layer: 1 of 1

Lab ID #: 119620 - 11 Asbestos Present: YES Other - 90% Cust. #: WA-HM-06A Chrysotile - 10% Material: Flashing (Roof) Location:

Appearance: black,fibrous,homogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 5 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 12 Asbestos Present:

Cust. #: WA-HM-06B Material: Flashing (Roof) Location: NOT ANALYZED Appearance:

Layer: 1 of 1

Lab ID #: 119620 - 13 Asbestos Present: NO Cellulose - 40% Cust. #: WA-HM-07A No Asbestos Observed Other - 60% Material: Rolled Brown Shingle Location:

Appearance: black,fibrous,nonhomogenous Layer: 1 of 2

Lab ID #: 119620 - 13a Asbestos Present: YES Other - 90% Cust. #: WA-HM-07A Chrysotile - 10% Material: Roof Tar Location:

Appearance: black,fibrous,homogenous Layer: 2 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 6 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 14 Asbestos Present: NO Cellulose - 40%

Cust. #: WA-HM-07B No Asbestos Observed Other - 60% Material: Rolled Brown Shingle Location:

Appearance: black,fibrous,nonhomogenous Layer: 1 of 1

Lab ID #: 119620 - 15 Asbestos Present: YES Other - 95% Cust. #: WA-HM-08A Chrysotile - 5% Material: 12x12 Red Medallion Vinyl Floor Tile Location:

Appearance: red,fibrous,homogenous Layer: 1 of 2

Lab ID #: 119620 - 15a Asbestos Present: NO Other - 100% Cust. #: WA-HM-08A No Asbestos Observed Material: Glue Location:

Appearance: yellow,nonfibrous,homogenous Layer: 2 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 7 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 16 Asbestos Present:

Cust. #: WA-HM-08B Material: 12x12 Red Medallion Vinyl Floor Tile Location: NOT ANALYZED Appearance:

Layer: 1 of 2

Lab ID #: 119620 - 16a Asbestos Present: NO Other - 100% Cust. #: WA-HM-08B No Asbestos Observed Material: Glue Location:

Appearance: yellow,nonfibrous,homogenous Layer: 2 of 2

Lab ID #: 119620 - 17 Asbestos Present: NO Other - 100% Cust. #: WA-HM-09A No Asbestos Observed Material: Cement Board Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 8 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 18 Asbestos Present: NO Other - 100%

Cust. #: WA-HM-09B No Asbestos Observed Material: Cement Board Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 1

Lab ID #: 119620 - 19 Asbestos Present: NO Cellulose - 10% Cust. #: WA-HM-10A No Asbestos Observed Fiberglass - 5% Material: Cream Linoleum Other - 85% Location:

Appearance: brown,fibrous,nonhomogenous Layer: 1 of 1

Lab ID #: 119620 - 20 Asbestos Present: NO Cellulose - 10% Cust. #: WA-HM-10B No Asbestos Observed Fiberglass - 5% Material: Cream Linoleum Other - 85% Location:

Appearance: brown,fibrous,nonhomogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 9 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 21 Asbestos Present: YES Other - 95%

Cust. #: WA-HM-11A Chrysotile - 5% Material: 12x12 Brown & Gray Stone Vinyl Floor Tile Location:

Appearance: brown,fibrous,homogenous Layer: 1 of 2

Lab ID #: 119620 - 21a Asbestos Present: NO Other - 100% Cust. #: WA-HM-11A No Asbestos Observed Material: Glue Location:

Appearance: yellow,nonfibrous,homogenous Layer: 2 of 2

Lab ID #: 119620 - 22 Asbestos Present:

Cust. #: WA-HM-11B Material: 12x12 Brown & Gray Stone Vinyl Floor Tile Location: NOT ANALYZED Appearance:

Layer: 1 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 10 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 22a Asbestos Present: NO Other - 100%

Cust. #: WA-HM-11B No Asbestos Observed Material: Glue Location:

Appearance: yellow,nonfibrous,homogenous Layer: 2 of 2

Lab ID #: 119620 - 23 Asbestos Present: YES Other - 90% Cust. #: WA-HM-12A Chrysotile - 10% Material: Multilayered Gray Linoleum Location:

Appearance: grey,fibrous,homogenous Layer: 1 of 5

Lab ID #: 119620 - 23a Asbestos Present: NO Other - 100% Cust. #: WA-HM-12A No Asbestos Observed Material: Mastic Location:

Appearance: black,nonfibrous,homogenous Layer: 2 of 5

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 11 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 23b Asbestos Present: YES Other - 95%

Cust. #: WA-HM-12A Chrysotile - 5% Material: Red Floor Tile Location:

Appearance: red,fibrous,homogenous Layer: 3 of 5

Lab ID #: 119620 - 23c Asbestos Present: NO Other - 100% Cust. #: WA-HM-12A No Asbestos Observed Material: Glue Location:

Appearance: yellow,nonfibrous,homogenous Layer: 4 of 5

Lab ID #: 119620 - 23d Asbestos Present: NO Cellulose - 5% Cust. #: WA-HM-12A No Asbestos Observed Fiberglass - 5% Material: Linoleum Other - 90% Location:

Appearance: white,fibrous,nonhomogenous Layer: 5 of 5

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 12 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 24 Asbestos Present:

Cust. #: WA-HM-12B Material: Multilayered Gray Linoleum Location: NOT ANALYZED Appearance:

Layer: 1 of 5

Lab ID #: 119620 - 24a Asbestos Present: NO Other - 100% Cust. #: WA-HM-12B No Asbestos Observed Material: Mastic Location:

Appearance: black,nonfibrous,homogenous Layer: 2 of 5

Lab ID #: 119620 - 24b Asbestos Present:

Cust. #: WA-HM-12B Material: Red Floor Tile Location: NOT ANALYZED Appearance:

Layer: 3 of 5

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 13 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 24c Asbestos Present: NO Other - 100%

Cust. #: WA-HM-12B No Asbestos Observed Material: Glue Location:

Appearance: yellow,nonfibrous,homogenous Layer: 4 of 5

Lab ID #: 119620 - 24d Asbestos Present: NO Cellulose - 5% Cust. #: WA-HM-12B No Asbestos Observed Fiberglass - 5% Material: Linoleum Other - 90% Location:

Appearance: white,fibrous,nonhomogenous Layer: 5 of 5

Lab ID #: 119620 - 25 Asbestos Present: NO Other - 100% Cust. #: WA-HM-13A No Asbestos Observed Material: 12x12 Gray Mottled Vinyl Floor Tile Location:

Appearance: pink,nonfibrous,homogenous Layer: 1 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 14 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 25a Asbestos Present: NO Other - 100%

Cust. #: WA-HM-13A No Asbestos Observed Material: Glue Location:

Appearance: yellow,nonfibrous,homogenous Layer: 2 of 2

Lab ID #: 119620 - 26 Asbestos Present: NO Other - 100% Cust. #: WA-HM-13B No Asbestos Observed Material: 12x12 Gray Mottled Vinyl Floor Tile Location:

Appearance: red,nonfibrous,homogenous Layer: 1 of 2

Lab ID #: 119620 - 26a Asbestos Present: NO Other - 100% Cust. #: WA-HM-13B No Asbestos Observed Material: Glue Location:

Appearance: yellow,nonfibrous,homogenous Layer: 2 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 15 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 27 Asbestos Present: NO Cellulose - 2%

Cust. #: WA-HM-14A No Asbestos Observed Fiberglass - 15% Material: Gray Pebble Linoleum Other - 83% Location:

Appearance: grey,fibrous,nonhomogenous Layer: 1 of 1

Lab ID #: 119620 - 28 Asbestos Present: NO Cellulose - 2% Cust. #: WA-HM-14B No Asbestos Observed Fiberglass - 15% Material: Gray Pebble Linoleum Other - 83% Location:

Appearance: grey,fibrous,nonhomogenous Layer: 1 of 1

Lab ID #: 119620 - 29 Asbestos Present: NO Other - 100% Cust. #: WA-HS-01A No Asbestos Observed Material: Plaster Finish Coat Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 16 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 29a Asbestos Present: NO Hair - 5%

Cust. #: WA-HS-01A No Asbestos Observed Other - 95% Material: Plaster Base Coat Location:

Appearance: grey,fibrous,homogenous Layer: 2 of 2

Lab ID #: 119620 - 30 Asbestos Present: NO Other - 100% Cust. #: WA-HS-01B No Asbestos Observed Material: Plaster Finish Coat Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 2

Lab ID #: 119620 - 30a Asbestos Present: NO Hair - 2% Cust. #: WA-HS-01B No Asbestos Observed Other - 98% Material: Plaster Base Coat Location:

Appearance: grey,fibrous,homogenous Layer: 2 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 17 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 31 Asbestos Present: NO Other - 100%

Cust. #: WA-HS-01C No Asbestos Observed Material: Plaster Finish Coat Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 2

Lab ID #: 119620 - 31a Asbestos Present: NO Hair - 2% Cust. #: WA-HS-01C No Asbestos Observed Other - 98% Material: Plaster Base Coat Location:

Appearance: grey,fibrous,homogenous Layer: 2 of 2

Lab ID #: 119620 - 32 Asbestos Present: NO Other - 100% Cust. #: WA-HS-01D No Asbestos Observed Material: Plaster Finish Coat Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 18 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 32a Asbestos Present: NO Hair - 2%

Cust. #: WA-HS-01D No Asbestos Observed Other - 98% Material: Plaster Base Coat Location:

Appearance: grey,fibrous,homogenous Layer: 2 of 2

Lab ID #: 119620 - 33 Asbestos Present: NO Other - 100% Cust. #: WA-HS-01E No Asbestos Observed Material: Plaster Finish Coat Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 2

Lab ID #: 119620 - 33a Asbestos Present: NO Hair - 5% Cust. #: WA-HS-01E No Asbestos Observed Other - 95% Material: Plaster Base Coat Location:

Appearance: grey,fibrous,homogenous Layer: 2 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 19 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 34 Asbestos Present: NO Other - 100%

Cust. #: WA-HS-01F No Asbestos Observed Material: Plaster Finish Coat Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 2

Lab ID #: 119620 - 34a Asbestos Present: NO Hair - 1% Cust. #: WA-HS-01F No Asbestos Observed Other - 99% Material: Plaster Base Coat Location:

Appearance: grey,fibrous,homogenous Layer: 2 of 2

Lab ID #: 119620 - 35 Asbestos Present: NO Other - 100% Cust. #: WA-HS-01G No Asbestos Observed Material: Plaster Finish Coat Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 20 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 35a Asbestos Present: NO Hair - 2%

Cust. #: WA-HS-01G No Asbestos Observed Other - 98% Material: Plaster Base Coat Location:

Appearance: grey,fibrous,homogenous Layer: 2 of 2

Lab ID #: 119620 - 36 Asbestos Present: NO Wollastonite - 5% Cust. #: WA-HS-02A No Asbestos Observed Other - 95% Material: Textured Surfacing Location:

Appearance: white,fibrous,homogenous Layer: 1 of 1

Lab ID #: 119620 - 37 Asbestos Present: NO Wollastonite - 5% Cust. #: WA-HS-02B No Asbestos Observed Other - 95% Material: Textured Surfacing Location:

Appearance: white,fibrous,homogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 21 of 22

Report To: ARI Report # 25-119620 Mr. Aaron Paquet Date Collected:8/29-9/10/25 Red Cedar Consulting Date Received: 09/11/25 P.O. Box 13216 Date Analyzed: 09/17/25 Lansing, MI 48901 Date Reported: 09/18/25

Project: 521 Wildwood Ave.

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 119620 - 38 Asbestos Present: NO Wollastonite - 5%

Cust. #: WA-HS-02C No Asbestos Observed Other - 95% Material: Textured Surfacing Location:

Appearance: white,fibrous,homogenous Layer: 1 of 1

Lab ID #: Asbestos Present:

Cust. #:

Material:

Location:

Appearance:

Layer: of

Lab ID #: Asbestos Present:

Cust. #:

Material:

Location:

Appearance:

Layer: of

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 22 of 22

Attachment B Figure 1 Site Diagram

Figure 1a Site Diagram

Note: Figure created by Red Cedar Consulting Asbestos Sample Locations

521 Wildwood Ave.

-Not To Scale- Jackson, MI

Figure 1b Site Diagram

Note: Figure created by Red Cedar Consulting Asbestos Sample Locations

521 Wildwood Ave.

-Not To Scale- Jackson, MI

Tables

Table 1 - Summary of Hazardous Materials, 521 Wildwood Ave Jackson, Michigan

Hazardous Materials Description and Location

Location Material Description Quantity

No Hazardous Materials Identified

Table 2 - Summary of Sample Descriptions and Asbestos Laboratory Results, 521 Wildwood Ave. Jackson, Michigan

Sample Number Sample Description Friable Material

Type Material

Classification

% Asbestos Laboratory

Result Sample Location Approx. Material

Quantity

WA-HM-01A Brown Shingle No M Category I ND Building Exterior NA

WA-HM-01B Brown Shingle No M Category I ND Building Exterior NA

WA-HM-02A Drywall and Joint Compound Yes M Category II ND/ND Kitchen NA WA-HM-02B Drywall and Joint Compound Yes M Category II ND/ND Dining NA

WA-HM-03A Beige Linoleum No M Category I 10%CH Dining 468 sq. ft.

WA-HM-03B Beige Linoleum No M Category I NA Dining NA WA-HM-04A 12”x12” Red Vinyl Floor Tile No M Category I 5%CH/ND Bedroom 1 168 sq. ft.

WA-HM-04B 12”x12” Red Vinyl Floor Tile No M Category I NA/ND Bedroom 1 NA

WA-HM-05A Tan 9” Square Linoleum No M Category I ND Kitchen NA WA-HM-05B Tan 9” Square Linoleum No M Category I ND Kitchen NA

WA-HM-06A Flashing (Roof) No M Category I 10%CH Building Exterior 30 lin. ft.

WA-HM-06B Flashing (Roof) No M Category I NA Building Exterior NA WA-HM-07A Rolled Brown Shingle No M Category I ND/10%CH Building Exterior 100 sq. ft.

WA-HM-07B Rolled Brown Shingle No M Category I ND Building Exterior NA

WA-HM-08A 12”x12” Red Medallion Vinyl Floor Tile No M Category I…