Appendix F1 - Ft Lyon Em Generator Design Drawings 10.11.2024.pdf

1. GENERAL: THESE DRAWINGS REMAIN THE SOLE PROPERTY OF MCSHEA CONSULTING AND MAY BE USED ONLY FOR THE PROJECT AS INDICATED BY NAME AND LOCATION. ANY OTHER USE REQUIRES PRIOR, WRITTEN PERMISSION. THE CONTRACTOR WILL PROVIDE ALL MATERIALS, LABOR, EQUIPMENT, TOOLS, TRANSPORTATION, LICENSES, FEES, PERMITS, ETC. TO COMPLETE THE ELECTRICAL WORK DESCRIBED ON THE DRAWINGS. THE CONTRACTOR WILL WARRANT EQUIPMENT, MATERIAL AND WORKMANSHIP FOR A MINIMUM PERIOD OF ONE YEAR FROM THE DATE OF ACCEPTANCE. WARRANTY SHALL INCLUDE REPLACEMENTS OR REPAIRS WITHOUT COST TO THE OWNER DURING THE WARRANTY PERIOD. ELECTRICAL WORK SHALL BE PERFORMED IN ACCORDANCE WITH THE 2018 NATIONAL ELECTRICAL CODE (NEC) AND ALL OTHER APPLICABLE LOCAL CODES AND ORDINANCES. ALL EQUIPMENT SHALL BE

INSTALLED IN ACCORDANCE WITH MANUFACTURERS' RECOMMENDATIONS.

2. USE OF DRAWINGS: DO NOT SCALE FROM THE ELECTRICAL DRAWINGS. FOR EXACT LOCATIONS USE ARCHITECT'S DIMENSIONED DRAWINGS, SHOP DRAWINGS AND FIELD MEASUREMENTS. VERIFY ALL LOCATIONS WITH THE

ARCHITECT PRIOR TO ELECTRICAL ROUGH-IN.

3. WIRING: ALL WIRING FOR LIGHTING AND POWER SYSTEMS WILL BE IN CONDUIT OR CABLE ASSEMBLIES APPROVED BY THE GOVERNING AUTHORITIES. CONDUCTOR SIZES SHOWN ARE BASED ON AMPACITIES FOR COPPER CONDUCTORS, UNLESS OTHERWISE NOTED. WHEN APPROVED BY ENGINEER, FEEDERS MAY BE ALUMINUM CONDUCTORS OF EQUIVALENT AMPACITIES. GROUNDING CONDUCTORS SHALL BE PROVIDED FOR ALL CIRCUITS SHOWN ON THE DRAWINGS. PROVIDE BLOCKING AND OTHER NECESSARY SUPPORTS IN WALLS AND CEILINGS FOR MATERIAL AND EQUIPMENT TO BE PROVIDED. BRANCH CIRCUIT NUMBERS SHOWN ON THE DRAWINGS MAY BE REARRANGED WITHIN A GIVEN PANELBOARD TO SUIT THE NEEDS OF THE INSTALLATION. ELECTRICAL BRANCH CIRCUITS SHALL BE

BALANCED BETWEEN LINES AND PHASES.

4. UTILITY COORDINATION: PROVIDE ALL COORDINATION WITH THE UTILITY INCLUDING LOAD DATA FORMS AND APPLICATION FOR SERVICE AS APPLICABLE. INSTALLATION OF SERVICE, PRIMARY OR SECONDARY FEEDERS AND

METERING SHALL BE PERFORMED IN ACCORDANCE WITH THE UTILITIY REQUIREMENTS.

5. GROUNDING: PROVIDE A COMPLETE GROUNDING SYSTEM AS REQUIRED BY THE NEC AND LOCAL AUTHORITIES HAVING JURISDICTION. ALL BRANCH CIRCUITS SHALL INCLUDE A GROUND CONDUCTOR. USE OF RACEWAY FOR

GROUNDING IS NOT PERMITTED. GALVANIZED GROUND RODS ARE NOT PERMITTED.

6. PANELBOARDS: PROVIDE MINIMUM INTEGRATED EQUIPMENT SHORT CIRCUIT RATING AS INDICATED ON PANEL SCHEDULES. PROVIDE BOLT-ON BREAKERS UNLESS OTHERWISE NOTED. PROVIDE CIRCUIT BREAKERS SHOWN ON THE PANELBOARD SCHEDULES. ALL TERMINATIONS AND LUGS SHALL BE RATED FOR 75-DEGREE CONDUCTORS.

7. PROVIDE TYPEWRITTEN CIRCUIT SCHEDULES TO IDENTIFY PANELBOARD AND EACH BRANCH BREAKER. ACCEPTABLE

MANUFACTURERS ARE SQUARE D, SIEMENS AND EATON.

8. WIRING DEVICES: PROVIDE SPECIFICATION GRADE 15 AND 20- AMPERE SWITCH AND RECEPTACLE DEVICES, AS APPLICABLE. OTHER DEVICES SHALL BE PROVIDED AS INDICATED AND SHALL MATCH PLUG-CONNECTED EQUIPMENT FURNISHED FOR THE PROJECT. DEVICE WALL PLATES SHALL BE SMOOTH, NYLON TYPE AND SHALL BE OFFICE WHITE

IN COLOR OR AS OTHERWISE SPECIFIED. DEVICE COLOR SHALL MATCH WALL PLATES.

9. DISCONNECT SWITCHES: HEAVY DUTY QUICK-MAKE, QUICK-BREAK TYPE, NON-FUSED UNLESS OTHERWISE NOTED.

PROVIDE MEANS TO LOCK SWITCH IN OFF POSITION WITH PAD-LOCK. ENCLOSURES SHALL BE NEMA TYPE 1 OR NEMA TYPE 3R FOR OUTDOOR INSTALLATION. PROVIDE PERMANENT LABELS FOR DISCONNECTS TO INDICATE EQUIMENT

SERVED.

10. LIGHTING FIXTURES: SEE LIGHT FIXTURE SCHEDULE. PROVIDE ALL FIXTURES WITH LAMPS AS INDICATED. WHERE REQUIRED, FIXTURES SHALL BE WET OR DAMP LOCATION LABELED. VERIFY MOUNTING HEIGHTS PRIOR TO

ELECTRICAL ROUGH-IN.

11. ALTERNATES NOT ACCEPTABLE UNLESS NOTED AS "OR EQUAL" ON LIGHT FIXTURE SCHEDULE.

12. VOICE/DATA: RACEWAY SYSTEM BY CONTRACTOR. ALL RACEWAYS SHALL BE PROVIDED WITH PULLSTRINGS OF MINIMUM OF 400-LB. TEST STRENGTH. ALL EQUIPMENT, RECEPTACLES AND CABLING BY OTHERS. PROVIDE BLANK COVERS OVER ALL UNUSED OUTLETS. CABLES, DEVICES AND CABLE TERMINATION IS BY OTHERS.

13. ELECTRICAL CONTRACTOR TO VERIFY CONNECTION TYPE, POWER REQUIREMENTS, MOUNTING HEIGHTS, AND LOCATIONS OF ALL EQUIPMENT WITH TENANT PRIOR TO ROUGH IN. SEE MANUFACTURER'S INSTALLATION MANUALS

FOR SPECIFIC DETAILS ON ALL EQUIPMENT.

14. (E) DENOTES DEVICE IS EXISTING. EXISTING DEVICES TO REMAIN ON EXISTING CIRCUIT AND/OR SWITCHES UNLESS

SHOWN OTHERWISE.

15. (R) DENOTES DEVICE IS BEING RELOCATED FROM WITHIN EXISTING SPACE AND TO REMAIN ON EXISTING CIRCUIT

AND/OR SWITCH UNLESS SHOWN OTHERWISE.

16. INFORMATION ON EXISTING CONDITIONS ARE BASED ON EXISTING PANEL DIRECTORIES, AVAILABLE DRAWINGS FROM LOCAL BUILDING DEPARTMENTS, AND ON SITE VERIFICATIONS WHERE POSSIBLE. ELECTRICAL CONTRACTOR TO

COORDINATE WITH ALL EXISTING CONDITIONS PRIOR TO NEW CONSTRUCTION.

17. VERIFY THAT ALL EXISTING EQUIPMENT SCHEDULED TO BE REUSED IS IN GOOD WORKING CONDITION. REPAIR AND

REPLACE AS NEEDED.

18. CONTRACTORS AND SUB-CONTRACTORS SHALL CAREFULLY REVIEW THE CONSTRUCTION DOCUMENTS.

INFORMATION REGARDING THE COMPLETE WORK IS DISPERSED THROUGHOUT THE DOCUMENT SET AND CANNOT BE

ACCURATELY DETERMINED WITHOUT REFERENCE TO THE COMPLETE DOCUMENT SET.

19. DEMOLITION PLANS SHOW GENERAL DEMOLITION WORK TO BE PERFORMED. NOT ALL EXISTING CONDITIONS SHOWN.

CONTRACTOR TO PERFORM ALL NECESSARY DEMOLITION WORK REQUIRED TO PRODUCE THE BUILDING MODIFICATIONS SHOWN ON THE CONTRACT DOCUMENTS. COORDINATE WITH BUILDING OWNER PRIOR TO DISPOSAL

OF ANY EXISTING EQUIPMENT.

20. ALL ABANDONED UTILITIES ARE TO HAVE CONDUITS, PIPING, OR WIRES REMOVED BACK TO SOURCE OR CAPPED OFF

IN CONCEALED SPACES WHERE POSSIBLE.

21. VERIFY ALL EQUIPMENT REQUIREMENTS AND FINAL LOCATIONS WITH TENANT AND MANUFACTURER.

22. ALL EXPOSED CONDUIT SHALL BE ROUTED PERPENDICULAR, PARALLEL, AND TIGHT TO NEW/EXISTING STRUCTURAL

ELEMENTS.

23. GFI PROTECTION (WHERE REQUIRED PER CODE) TO BE LOCATED ON FACEPLATE OF RECEPTACLE. IF FACEPLATE IS NOT EASILY ACCESSIBLE THEN PROVIDE GFI CIRCUIT BREAKER. GFCI DEVICES MAY NOT BE LOCATED ABOVE OR

BEHIND APPLIANCES.

24. CONNECT EGRESS LIGHTING FIXTURES AND EXIT SIGNS TO AREA LIGHTING CIRCUIT AHEAD OF ANY SWITCH PER NEC 700-12(F) INCLUDING ANY NIGHT LIGHTS. FIXTURES SHOWN SHADED OR LABELED ARE EMERGENCY EGRESS (EM)

WITH BATTERY PACK, NIGHT LIGHT (N) OR BOTH (EM/N).

25. COORDINATE TELECOM, DATA, SECURITY, AND AV EQUIPMENT WITH TENANT AND EQUIPMENT PROVIDERS.

26. ALL DEDICATED CIRCUITS SHALL HAVE THEIR OWN SEPARATE HOT, NEUTRAL, AND GROUND WIRES. CONDUIT SHALL

NOT BE USED AS A GROUND. NEUTRAL AND GROUNDS SHALL NOT BE SHARED.

27. MC CABLE ONLY ALLOWED IN CONCEALED AREAS THAT WILL NOT BE SUBJECTED TO DAMAGE. EXAMPLES ARE ABOVE

CEILINGS AND WITHIN WALLS.

28. ELECTRICAL CONTRACTOR TO COORDINATE ALL LOW VOLTAGE, SPEAKER, AND VOLUME CONTROL WORK. SINGLE GANG PRE-CONSTRUCTION RING FOR EACH VOLUME CONTROL LOCATION WITH PULL STRING, CONDUIT STUB UP

WHERE REQUIRED AT 48" FROM FINISHED FLOOR

29. CONTRACTOR TO REVIEW ENTIRE CONSTRUCTION DOCUMENT SET OF PROJECT TO COORDINATE ALL NECESSARY WORK. THIS INCLUDES MECHANICAL DRAWINGS FOR ALL SWITCHES, CONTROLS, AND INTERLOCKS.

2021 INTERNATIONAL BUILDING CODE

2021 INTERNATIONAL FIRE CODE

2021 INTERNATIONAL MECHANICAL CODE

2021 INTERNATIONAL FUEL GAS CODE

2021 INTERNATIONAL PLUMBING CODE

2021 INTERNATIONAL ENERGY CONSERVATION CODE

2023 NATIONAL ELECTRIC CODE (NEC)

2021 INTERNATIONAL EXISTING BUILDING CODE

HEALTH DEPARTMENT RULES AND REGULATIONS

NATIONAL FIRE PROTECTION ASSOCIATION STANDARDS

IN CASE OF CONFLICTS WITH CODE, DRAWINGS OR SPECIFICATION, THE MORE STRINGENT SHALL PREVAIL.

GENERAL ELECTRICAL NOTES

WIRING NOTES

NO.4 AWG

NO.6 AWG

NO.8 AWG

NO.10 AWG

NO.12 AWG

HOMERUN WIRE SIZE

NO.10 AWG191FT TO 300FT

NO.10 AWG121FT TO 190FT

NO.12 AWG

NO.12 AWG

NO.10 AWG

CIRCUIT WIRE SIZELENGTH

1FT TO 50FT

76FT TO 120FT

51FT TO 75FT

HOMERUNS AND BRANCH WIRING FOR 20 AMP CIRCUITS SHALL BE AS FOLLOWS:

FIRE ALARM WIRING:

1. FIRE ALARM INSTALLER TO COORDINATE WITH FIRE MARSHALL ON REQUIRED

DOCUMENTATION NEEDED.

2. FIRE ALARM INSTALLER TO VERIFY LOCATION OF FIRE ALARM PANEL.

3. FIRE ALARM INSTALLER TO PROVIDE DUCT SMOKE DETECTORS FOR HVAC UNITS PER

SECTION 606 OF THE INTERNATIONAL MECHANICAL CODE. REFER TO MECHANICAL

RTU SCHEDULE FOR DETERMINATION OF UNITS TO RECEIVE SMOKE DETECTORS.

MOUNTING HEIGHT NOTES

MOUNTING HEIGHT OF ALL EXISTING AND NEW ELECTRICAL RECEPTACLES, SWITCHES

AND CONTROLS SHALL COMPLY WITH ICC/ANSI A117.1-2017

· PER SECTION 308.2 FORWARD REACH.

·· UNOBSTRUCTED - MINIMUM OF 15 INCHES AND A MAXIMUM OF 48 INCH ABOVE

FINISHED FLOOR.

·· OBSTRUCTED - WHERE OBSTRUCTION IS 20 INCHES MAX A MAXIMUM OF 48

INCHES ABOVE FINISHED FLOOR. WHERE OBSTRUCTION EXCEEDS 20 INCHES A

MAXIMUM OF 44 INCHES ABOVE FINISHED FLOOR.

· PER SECTION 308.3 SIDE REACH.

·· UNOBSTRUCTED - MINIMUM OF 15 INCHES AND A MAXIMUM OF 48 INCHES ABOVE

FINISHED FLOOR.

·· OBSTRUCTED - WHERE OBSTRUCTION HEIGHT IS 34 INCHES MAX AND DEPTH IS

GREATER THAN 10 AND 24 INCHES MAX A MAXIMUM OF 46 INCHES ABOVE

FINISHED FLOOR. WHERE OBSTRUCTION HEIGHT IS 34 INCHES MAX AND DEPTH

IS 10 INCHES MAX A MAXIMUM OF 48 INCHES ABOVE FINISHED FLOOR.

LIGHTING SYMBOLS

DESCRIPTIONSYMBOL

UNO

ELECTRICAL SYMBOL LEGEND

X

X

X

X X

X

D

OC

SPECIAL SYSTEMS SYMBOLS

S

S

E

N

PUSH BUTTON DOOR BELLDB

REMOTE RELEASE. PROVIDE JUNCTION BOX WITH 3/4" CONDUIT UP IN WALL WITH PULL

STRING STUBBED 24" ABOVE CEILING.KE

ALARM CONTROL KEYPAD. PROVIDE JUNCTION BOX WITH 3/4" CONDUIT UP IN WALL WITH

PULL STRING STUBBED 24" ABOVE CEILING.AK

ACCESS CONTROL KEYPAD. PROVIDE JUNCTION BOX WITH 3/4" CONDUIT UP IN WALL

WITH PULL STRING STUBBED 24" ABOVE CEILING.KP

INTERCOM. PROVIDE JUNCTION BOX WITH 3/4" CONDUIT UP IN WALL WITH PULL STRING

STUBBED 24" ABOVE CEILING.I

PANIC BUTTON. PROVIDE JUNCTION BOX WITH 3/4" CONDUIT UP IN WALL WITH PULL

STRING STUBBED 24" ABOVE CEILING.P

AMBUSH MONITOR. PROVIDE JUNCTION BOX WITH 3/4" CONDUIT UP IN WALL WITH PULL

STRING STUBBED 24" ABOVE CEILING.AM

CCTV CAMERA LOCATION. PROVIDE JUNCTION BOX WITH 3/4" CONDUIT UP IN WALL WITH

PULL STRING STUBBED 24" ABOVE CEILING.

POWER SYMBOLS

M

J J

ABBREVIATIONS

COMMUNICATION SYSTEM SYMBOLS

CIRCUITING SYSTEM SYMBOLS

FIRE ALARM SYMBOLS

F F

F

F

S

H

S

ONE-LINE SYMBOLS

ID

AMPS

VOLTS

G

N L

NOTE: NOT ALL SYMBOLS ARE USED. VERIFY ALL CONNECTIONS AND RECEPTACLE TYPES FOR EQUIPMENT FROM APPROVED MECHANICAL AND EQUIPMENT SUBMITTALS PRIOR TO INSTALLATION.

DESCRIPTIONSYMBOL

DESCRIPTIONSYMBOL

DESCRIPTIONSYMBOL

DESCRIPTIONSYMBOL

DESCRIPTIONSYMBOL

DESCRIPTIONSYMBOL

DESCRIPTIONSYMBOL

FACP

ACC

W

X

X

C

X xxAnP

M

L

ROCKER DIMMER WITH SIDE ADJUSTABLE SLIDE, SINGLE POLE SWITCH, 1000W, 120V,

UNO., MOUNT 48" AFF.

4-WAY, TOGGLE SWITCH, 20A, SINGLE POLE, VOLTAGE AS REQUIRED. MOUNT 48" AFF.

3-WAY, TOGGLE SWITCH, 20A, SINGLE POLE, VOLTAGE AS REQUIRED. MOUNT 48" AFF.

TOGGLE SWITCH, 20A, SINGLE POLE, VOLTAGE AS REQUIRED. MOUNT 48" AFF.

EXIT SIGN, ALL EXITS LIGHTS TO HAVE 1HR MINIMUM BATTERY BACKUP. SHADING

INDICATES ILLUMINATED FACE, PROVIDE CHEVRONS AS INDICATED. MOUNT 7'6" TO

BOTTOM OF FIXTURE ABOVE FINISHED FLOOR.

EMERGENCY LIGHT FIXTURE, IE FROGEYE, ALL EMERGENCY LIGHTS TO HAVE 1HR

MINIMUM BATTERY BACKUP.

LIGHT FIXTURE WITH EM BALLAST, EM BALLAST TO PROVIDE 1000 LUMENS MINIMUM.

TRACK HEAD, CAPITAL LETTER DENOTES TYPE.

POLE LIGHT, SEE LIGHT FIXTURE SCHEDULE AND DETAILS FOR POLE SPECIFICATION.

CAPITAL LETTER DENOTES TYPE.

BOLLARD, CAPITAL LETTER DENOTES TYPE.

SPOT LIGHT, CAPITAL LETTER DENOTES TYPE.

CEILING MTD. LIGHT FIXTURE, IE. GLOBE, DOWNLIGHT, PENDANT, ETC. SEE LIGHT

FIXTURE SCHEDULE FOR SIZE AND MOUNTING. CAPITAL LETTER DENOTES TYPE, LOWER

CASE LETTER DENOTES SWITCH LEG.

WALL MTD. LIGHT FIXTURE, IE. WALL PACK, SCONCE, CYLINDER, ETC. CAPITAL LETTER

DENOTES TYPE, LOWER CASE LETTER DENOTES SWITCH LEG.

WALL BRACKET LIGHT FIXTURE, SEE LIGHT FIXTURE SCHEDULE FOR SIZE. CAPITAL

LETTER DENOTES TYPE, LOWER CASE LETTER DENOTES SWITCH LEG.

STRIP LIGHT FIXTURE, SEE LIGHT FIXTURE SCHEDULE FOR SIZE AND MOUNTING.

CAPITAL LETTER DENOTES TYPE, LOWER CASE LETTER DENOTES SWITCH LEG.

LIGHT FIXTURE, SEE LIGHT FIXTURE SCHEDULE FOR SIZE AND MOUNTING. CAPITAL

LETTER DENOTES TYPE, LOWER CASE LETTER DENOTES SWITCH LEG.

NURSE CALL LIGHT

NURSE/EMERGENCY CALL BUTTON

WALL MTD. SPEAKER

CEILING MTD. SPEAKER

PUSHBUTTON OPERATOR.

LOW VOLTAGE SWITCH, WALL MTD., 48" AFF.

DUAL TECH OCCUPANCY SENSOR, CEILING MTD.

PHOTOCELL SWITCH, MOUNT ON NORTH FACING EXTERIOR WALL, UNO.

TELEPHONE OUTLET. WIRING BY OTHERS, UNO. MOUNT 18" AFF.

TELEPHONE OUTLET. WIRING BY OTHERS, UNO. WALL PHONE, MOUNT 48" AFF.

DATA OUTLET. WIRING BY OTHERS, UNO. MOUNT 18" AFF.

DATA/TELEPHONE OUTLET, WIRING BY OTHERS UNO. MOUNT 18" AFF.

CATV OUTLET, WIRING BY OTHERS, UNO. MOUNT 18" AFF.

CIRCUIT RUN, #12W, 1/2" CONDUIT UNO.

HOMERUN, #12W, 1/2" CONDUIT UNO., ARROWS INDICATE QUANTITY.

CIRCUIT RUN, UNDER FLOOR OR GROUND, #12W, 1/2" CONDUIT UNO.

BRANCH CIRCUIT WITH REQUIRED EQUIPMENT CONNECTION.

BRANCH CIRCUIT BREAK

HORN ONLY

HORN AND STROBE

STROBE ONLY

MANUAL PULL STATION

SMOKE DETECTOR

HEAT DETECTOR

DUCT SMOKE DETECTOR

MAGNETIC DOOR HOLD OPEN

FIRE/ SMOKE DAMPER

FIRE ALARM CONTROL PANEL

ANNUNCIATION PANEL

CIRCUIT BREAKER, FRAME AND TRIP AS INDICATED.

POWER TRANSFORMER, RATING AS INDICATED.

GROUND ELECTRODE

CURRENT TRANSFORMER (CT)

NON-FUSIBLE SWITCH, RATING AS INDICATED.

FUSIBLE SWITCH, RATING AND FUSE SIZE AS INDICATED.

FEEDER SCHEDULE KEY TAG

UTILITY TRANSFORMER

UTILITY ELECTRIC METER

MOTOR WITH DISCONNECT

MOTOR WITH CONTROLLER AND DISCONNECT

GENERATOR

TRANSFER SWITCH

WEATHERHEAD

PANELBOARD OR LOADCENTER, IDENTIFICATION, AMPERES AND VOLTAGE.

OVERHEAD DOOR

TAMPER-PROOF

MOUNT DEVICE 6" AFF, HORIZONTALLY.

ELECTRIC WATER COOLER

TRANSIENT VOLTAGE SURGE SUPPRESSOR

UNDER COUNTER, MOUNT RECEPTACLE HORIZONTALLY,

1" ABOVE BACKSPLASH. OVER COUNTER, MOUNT RECEPTACLE HORIZONTALLY,

UNLESS NOTED OTHERWISE.

FLUSH MTD. PANELBOARD/LOADCENTER.

SURFACE MTD. PANELBOARD/LOADCENTER.

FUSIBLE DISCONNECT SWITCH, RATING AS INDICATED.

NON FUSIBLE DISCONNECT SWITCH, RATING AS INDICATED. RATING AS INDICATED.

MOTOR

POWER POLE WITH COMM AND POWER.

4"X4" JUNCTION BOX, FLUSH/SURFACE MTD.

FLOOR BOX, FLUSH MOUNTED PROVIDE DEVICE, BOX AND COVER AS SPECIFIED.

MANUAL MOTOR STARTER WITH THERMAL OVERLOAD

PLUGMOLD, MULTI-OUTLET RACEWAY, RECEPTACLES SPACED 12" OC, UNO. MOUNT

ABOVE COUNTER.

SPECIAL PURPOSE RECEPTACLE, NEMA TYPE AS INDICATED. MOUNT AT HEIGHT AS

REQUIRED PER EQUIPMENT.

DUPLEX RECEPTACLE, 20A, 120V, 3 WIRE GROUNDED, NEMA 5-20R, UNO. WITH TIE-BAR

REMOVED FOR SWITCHING. MOUNT 18" AFF.

SPECIAL RECEPTACLE, 220V, TYPE AS INDICATED OR MATCH EQUIPMENT CAP. MOUNT

AT HEIGHT AS REQUIRED PER EQUIPMENT.

SIMPLEX RECEPTACLE, 20A, 120V, 3 WIRE GROUNDED, NEMA 5-20R, UNO. SUBSCRIPT 'C'

DENOTES CLOCK RECEPTACLE, MOUNT AT HEIGHT DIRECTED BY ARCHITECT.

QUAD RECEPTACLE, 20A, 120V, 3 WIRE GROUNDED, NEMA 5-20R, UNO. MOUNT 18" AFF.

SUBSCRIPT DENOTES TYPE. IE. IG=ISOLATED GROUND, GFI=GFCI, WP=WEATHERPROOF.

DUPLEX RECEPTACLE, 20A, 120V, 3 WIRE GROUNDED, NEMA 5-20R, UNO. MOUNT 18" AFF.

SUBSCRIPT DENOTES TYPE. IE. IG=ISOLATED GROUND, GFI=GFCI, WP=WEATHERPROOF,

C=CONTROLLED RECEPTACLE WITH ONE RECEPTACLE CONTROLLED VIA OCCUPANCY

SENSOR AND BE MARKED PER NEC 406.3(E).

T TIME SWITCH, WALL MTD., 48" AFF.

D DAYLIGHT SENSOR, MOUNT ON NORTH FACING EXTERIOR WALL, UNO.

OC

UC

TVSS

EWC

H

TP

OHD

DUPLEX RECEPTACLE SAME AS ABOVE BUT WITH (2)USB PORTS.

DUAL TECH OCCUPANCY SENSOR, WALL MTD., 48" AFF. PROVIDE 0-10V DIMMING

ADJUSTABLE SLIDE.

DUAL TECH OCCUPANCY SENSOR, WALL MTD.

X

X

X

X

X

PC

OC

OC

xxAnP

X

CEILING MOUNTEDCLG

DROP CORDD

X

2021 IECC COMPLIANCE

THE 2021 INTERNATIONAL ENERGY CODE (IECC) SHALL BE FOLLOWED FOR THESE SET OF DOCUMENTS. THE FOLLOWING

CODE SECTIONS ARE HIGHLIGHTED BUT DO NOT INCLUDE EVERYTHING REQUIRED.

401 GENERAL REQUIREMENTS

402 BUILDING ENVELOPE REQUIREMENTS

402.5.10 RECESSED LIGHTING

403 BUILDING MECHANICAL SYSTEMS

403.4.1.4 HEATED OR COOLED VESTIBULES

THE HEATING SYSTEM FOR HEATED VESTIBULES AND AIR CURTAINS WITH INTEGRAL HEATING SHALL BE PROVIDED WITH CONTROLS CONFIGURED TO SHUT OFF THE SOURCE OF HEATING WHEN THE OUTDOOR AIR TEMPERATURE IS GREATER THAN 45°F (7°C). VESTIBULE HEATING AND COOLING SYSTEMS SHALL BE CONTROLLED BY A THERMOSTAT LOCATED IN THE VESTIBULE CONFIGURED TO LIMIT HEATING TO A TEMPERATURE NOT GREATER THAN 60°F (16°C) AND COOLING TO A TEMPERATURE NOT LESS THAN 85°F (29°C).

403.13 MECHANICAL SYSTEMS LOCATED OUTSIDE OF THE BUILDING THERMAL ENVELOPE

SECTIONS 403.13.1 THROUGH 403.13.3 SHALL APPLY TO MECHANICAL SYSTEMS PROVIDING HEAT

OUTSIDE OF THE THERMAL ENVELOPE OF A BUILDING.

405 ELECTRICAL POWER AND LIGHTING SYSTEMS

405.2.1.1 OCCUPANT SENSOR CONTROL FUNCTION

OCCUPANT SENSOR CONTROLS IN WAREHOUSES SHALL COMPLY WITH SECTION 405.2.1.2. OCCUPANT SENSOR CONTROLS IN OPEN PLAN OFFICE AREAS SHALL COMPLY WITH SECTION 405.2.1.3. OCCUPANT SENSOR CONTROLS IN CORRIDORS SHALL COMPLY WITH SECTION 405.2.1.4. OCCUPANT SENSOR

CONTROLS FOR ALL OTHER SPACES SPECIFIED IN SECTION 405.2.1 SHALL COMPLY WITH THE

FOLLOWING:

1. THEY SHALL AUTOMATICALLY TURN OFF LIGHTS WITHIN 20 MINUTES AFTER ALL OCCUPANTS HAVE

LEFT THE SPACE.

2. THEY SHALL BE MANUAL ON OR CONTROLLED TO AUTOMATICALLY TURN ON THE LIGHTING TO NOT

MORE THAN 50% POWER.

3. THEY SHALL INCORPORATE A MANUAL CONTROL TO ALLOW OCCUPANTS TO TURN OFF LIGHTS.

405.2.2.1 TIME-SWITCH CONTROL FUNCTION

405.2.3.1 LIGHT-REDUCTION CONTROL FUNCTION

405.2.4 DAYLIGHT-RESPONSIVE CONTROLS

SECTIONS 405.2.4.1 THROUGH 405.2.4.4 SHALL APPLY TO DAYLIGHT-RESPONSIVE CONTROLS.

405.2.5 SPECIFIC APPLICATION CONTROLS

405.2.7 EXTERIOR LIGHTING CONTROLS

SECTIONS 405.2.7.1 THROUGH 405.2.7.4 SHALL APPLY TO EXTERIOR LIGHTING CONTROLS.

405.2.8 PARKING GARAGE LIGHTING CONTROL

405.4 LIGHTING FOR PLANT GROWTH AND MAINTENANCE

405.7 ELECTRICAL TRANSFORMERS:

ELECTRICAL TRANSFORMERS SHALL MEET THE MINIMUM EFFICIENCY REQUIREMENTS OF TABLE 405.7 AS TESTED AND RATED IN ACCORDANCE WITH THE TEST PROCEDURES LISTED IN DOE 10 CFR 431.

405.8 ELECTRICAL MOTORS:

ELECTRICAL MOTORS SHALL MEET THE MINIMUM EFFICIENCY REQUIREMENTS OF TABLES 405.8(1)

THROUGH 405.8(4) WHEN TESTED AND RATED IN ACCORDANCE WITH THE DOE 10 CFR 431.

405.11 AUTOMATIC RECEPTACLE CONTROL

THE FOLLOWING SHALL HAVE AUTOMATIC RECEPTACLE CONTROL COMPLYING WITH SECTION 405.11.1:

1. AT LEAST 50% OF ALL 125V, 15- AND 20-AMP RECEPTACLES INSTALLED IN ENCLOSED OFFICES, CONFERENCE ROOMS, ROOMS USED PRIMARILY FOR COPY OR PRINT FUNCTIONS, BREAKROOMS, CLASSROOMS AND INDIVIDUAL WORKSTATIONS, INCLUDING THOSE INSTALLED IN MODULAR

FURNITURE NOT SHOWN ON THE CONSTRUCTION DOCUMENTS.

2. AT LEAST 25% OF BRANCH CIRCUIT FEEDERS INSTALLED FOR MODULAR FURNITURE NOT SHOWN ON

THE CONSTRUCTION DOCUMENTS.

405.11.1 AUTOMATIC RECEPTACLE CONTROL FUNCTION

406 ADDITIONAL EFFICIENCY REQUIREMENTS

406.1 NEW BUILDINGS SHALL ACHIEVE A TOTAL OF 10 CREDITS FROM TABLES 406.1(1) THROUGH 406.1(5) WHERE THE TABLE IS SELECTED BASED ON THE USE GROUP OF THE BUILDING AND FROM CREDIT

CALCULATIONS AS SPECIFIED IN RELEVANT SUBSECTIONS OF SECTION 406.

408 SYSTEM COMMISSIONING

408.2.1 COMMISSIONING PLAN REQUIRED

408.3.1 FUNCTIONAL TESTING

PRIOR TO PASSING FINAL INSPECTION, THE REGISTERED DESIGN PROFESSIONAL OR APPROVED AGENCY SHALL PROVIDE EVIDENCE THAT THE LIGHTING CONTROL SYSTEMS HAVE BEEN TESTED TO ENSURE THAT CONTROL HARDWARE AND SOFTWARE ARE CALIBRATED, ADJUSTED, PROGRAMMED AND

IN PROPER WORKING CONDITION IN ACCORDANCE WITH THE CONSTRUCTION DOCUMENTS AND

MANUFACTURER'S INSTRUCTIONS. FUNCTIONAL TESTING SHALL BE IN ACCORDANCE AND PER THE PROCEDURES WITHIN SECTIONS 408.3.1.1 AND 408.3.1.3 FOR THE APPLICABLE CONTROL TYPE.

408.3.2 DOCUMENTATION REQUIREMENTS

A FINAL COMMISSIONING REPORT SHALL BE DELIVERED TO THE BUILDING OWNER PER SECTION 408.2.5

OF THE 2021 IECC.

C CO DETECTOR

OWNERSHIP OF INSTRUMENTS OF

SERVICE

All Drawings, Reports, Plans, Specifications, Computer Files (including CAD files), field information, notes, sketches, and other design materials prepared by the Engineer and his/her consultants as instruments of service shall remain the property of the Engineer. The Engineer shall retain all common law, statutory and other reserved rights, including the Copyright thereto.

SHEET

FO

R

T

LY

O N

E M

ER

G

EN

C

Y G

EN

ER

AT

O

R R

EP

LA

C

EM

EN

T

C

O R

D

5, L

AS

A

N

IM

AS

C O

PROJECT #: 23-6865

DRAWN BY: JL

CHECKED BY: MRM

FULL SET ISSUE HISTORY:

REVIEW SET 06.26.20241

CLIENT:

SHEET REVISION:

cShea 4445 Northpark Dr. Suite 200 Colorado Springs, CO 80907 mcsheaconsulting.com Project #: 23-6865 onsulting, LLC

MECHANICAL + ELECTRICAL + PLUMBING

E0.1

ARCHITECT:

11/11/2024

90% REVIEW SET 09.25.20242

BID SET 10.11.20243

AutoCAD SHX Text S

AutoCAD SHX Text S

AutoCAD SHX Text S

AutoCAD SHX Text S

AutoCAD SHX Text S

AutoCAD SHX Text S

AutoCAD SHX Text S

AutoCAD SHX Text S

OWNERSHIP OF INSTRUMENTS OF

SERVICE

All Drawings, Reports, Plans, Specifications, Computer Files (including CAD files), field information, notes, sketches, and other design materials prepared by the Engineer and his/her consultants as instruments of service shall remain the property of the Engineer. The Engineer shall retain all common law, statutory and other reserved rights, including the Copyright thereto.

SHEET

FO

R

T

LY

O N

E M

ER

G

EN

C

Y G

EN

ER

AT

O

R R

EP

LA

C

EM

EN

T

C

O R

D

5, L

AS

A

N

IM

AS

C O

PROJECT #: 23-6865

DRAWN BY: JL

CHECKED BY: MRM

FULL SET ISSUE HISTORY:

REVIEW SET 06.26.20241

CLIENT:

SHEET REVISION:

cShea 4445 Northpark Dr. Suite 200 Colorado Springs, CO 80907 mcsheaconsulting.com Project #: 23-6865 onsulting, LLC

MECHANICAL + ELECTRICAL + PLUMBING

E4-0.1

ARCHITECT:

11/11/2024

90% REVIEW SET 09.25.20242

BID SET 10.11.20243

500KVA

UTILITY

TRANSFORMER

1200A SERVICE

RATED AUTOMATIC

3-POLE TRANSFER

SWITCH

750 KVA

GENERATOR

480/277V, 3Ø

300kVA

NEMA

3R

XFMR

XFMR

(E)

PANEL

'DP3'

600A

480/277V 3Ø(E)

600A (E)

600A

(E) 600A, 480/277V, 2 SECTION

PANEL

'D3'

(E) 1600A, 208/120V

'MSB-4L'

OUTSIDE INSIDE

600A

600A 480V

NEMA 3R

DISCONNECT

600A

DISCONNECT

#2/0 AL

GND. IN

"3C

X

ISC = 42,958A

X

ISC = 18,798A

X

ISC = 9,983A

X

ISC = 9,941A

X

ISC = 16,556A

XISC = 9,966A

600A

DISCONNECT

DP3

1200A

MAIN

C .W

. P

IP

E

SE

R

VI

C E

G R

O U

N D

R O

D

BU

IL

D

IN

G S

TE

EL

#3 /0

#3 /0

#4 C

U

#3 /0

#3 /0

TE

LE

PH

O

N E

BO

AR

D

#6

GROUND BUS

20' MIN. CONCRETE

ENCASED ELECTRODE

EXOTHERMIC WELDED

CONNECTION

1600A

EXISTING

SERVICE

TRANSFORMER

480V,3Ø

(2 OF 2)

(E)

XFMR

(E)

PANEL

'DP3'

600A

480/277V 3Ø(E)

600A

EXISTING

SERVICE

TRANSFORMER

208V,3Ø

(1 OF 2)

(E)

XFMR

(E) 600A

(E) 600A, 480/277V, 2 SECTION

PANEL

'D3'

(E) 1600A, 208/120V

'MSB-4L'

OUTSIDE INSIDE

1600A

ELEVATORELEVATOR

J (E)

'EM4'(E)

'DP-4A'(E)

'EM4'(E)

SERVICE

DISCONNECT (E)

DEMO

EXISTING SERVICE

TRANSFORMER (2 OF 2)

DEMO

EXISTING SERVICE

TRANSFORMER (1 OF 2)

"MSB-4L"

XFMR (E)

ATS ABOVE (E)

"DP3" (E)

ELEVATOR

DISCONNECT (E)

ELEVATOR

DISCONNECT (E)

ELEV TRANSFER

ELEVATORELEVATOR

500KVA, 480V, 3Ø,

UTILITY TRANSFORMER

(REUSE EXISTING PAD)

600A, 480V

NEMA 3R

DISCONNECT (2 OF 2)

1200A, 480V, SERVICE

RATED AUTOMATIC

3-POLE TRANSFER

SWITCH

300KVA, 3Ø, NEMA 3R

TRANSFORMER

(REUSE EXISTING PAD)

750KVA

EMERGENCY

GENERATOR

ENCLOSURE

J (E)

'EM4'(E)

'DP-4A'(E)

'EM4'(E)

SERVICE

DISCONNECT (E)

"MSB-4L"

XFMR (E)

ATS ABOVE (E)

"DP" (E)

ELEVATOR

DISCONNECT (E)

ELEVATOR

DISCONNECT (E)

ELEV TRANSFER

OWNERSHIP OF INSTRUMENTS OF

SERVICE

All Drawings, Reports, Plans, Specifications, Computer Files (including CAD files), field information, notes, sketches, and other design materials prepared by the Engineer and his/her consultants as instruments of service shall remain the property of the Engineer. The Engineer shall retain all common law, statutory and other reserved rights, including the Copyright thereto.

SHEET

FO

R

T

LY

O N

E M

ER

G

EN

C

Y G

EN

ER

AT

O

R R

EP

LA

C

EM

EN

T

C

O R

D

5, L

AS

A

N

IM

AS

C O

PROJECT #: 23-6865

DRAWN BY: JL

CHECKED BY: MRM

FULL SET ISSUE HISTORY:

REVIEW SET 06.26.20241

CLIENT:

SHEET REVISION:

cShea 4445 Northpark Dr. Suite 200 Colorado Springs, CO 80907 mcsheaconsulting.com Project #: 23-6865 onsulting, LLC

MECHANICAL + ELECTRICAL + PLUMBING

E4-1.1

ARCHITECT:

11/11/2024

90% REVIEW SET 09.25.20242

BID SET 10.11.20243

SCALE:

PROPOSED ONE-LINE DIAGRAM - BUILDING 4

E4-1.1 NONESCALE:

EXISTING ONE-LINE DIAGRAM - BUILDING 41

E4-1.1 NONE

SCALE:

EXISTING BUILDING 4 ELECTRICAL PLAN

1/8"=1'-0"E4-1.1

SCALE:

PROPOSED BUILDING 4 ELECTRICAL PLAN

1/8"=1'-0"E4-1.1

CONCRETE FOOTER

All Drawings, Reports, Plans, Specifications, Computer Files (including CAD files), field information, notes, sketches, and other design materials prepared by the Engineer and his/her consultants as instruments of service shall remain the property of the Engineer. The Engineer shall retain all common law, statutory and other reserved rights, including the Copyright thereto.

SHEET

FO

R

T

LY

O N

E M

ER

G

EN

C

Y G

EN

ER

AT

O

R R

EP

LA

C

EM

EN

T

C

O R

D

5, L

AS

A

N

IM

AS

C O

PROJECT #: 23-6865

DRAWN BY: JL

CHECKED BY: MRM

FULL SET ISSUE HISTORY:

REVIEW SET 06.26.20241

CLIENT:

SHEET REVISION:

cShea 4445 Northpark Dr. Suite 200 Colorado Springs, CO 80907 mcsheaconsulting.com Project #: 23-6865 onsulting, LLC

MECHANICAL + ELECTRICAL + PLUMBING

E6-0.1

ARCHITECT:

11/11/2024

(E)

TRANSFORMER

1200A 480V SERVICE

RATED AUTOMATIC

3-POLE TRANSFER

SWITCH

XFMR

(E)

400 KVA

GENERATOR

480/277V, 3Ø

OUTSIDE INSIDE

(E)

PANEL 'MSB-6H'

1200A, 480/277V, 3Ø

1200A

MCB

(E)

PANEL

'EMD-6'

300A 480/277V

3Ø

NEW FEEDER

ISC = 42,958A

ISC = 42,958A

X

ISC = 22,247A

1200A

MAIN

300A

C .W

. P

IP

E

SE

R

VI

C E

G R

O U

N D

R O

D

BU

IL

D

IN

G S

TE

EL

#3 /0

#3 /0

#4 C

U

#3 /0

#3 /0

TE

LE

PH

O

N E

BO

AR

D

#6

GROUND BUS

20' MIN. CONCRETE

ENCASED ELECTRODE

EXOTHERMIC WELDED

CONNECTION

X X

STAIR

UP

'EMD6'(E)

'FL6'(E)

'F'(E)

'MSB-6H'(E)

LIGHTING

CONTACTOR(E)

'EM6'(E)

'UC'(E)

'D'(E)

'E'(E)

'G'(E)

J

(E)

EXISTING SERVICE

TRANSFORMER

EXISTING

EMERGENCY

GENERATOR

ENCLOSURE

ATS (D)

480V

TRANSFORMER

XFMR

(E)

PANEL 'MCB-6'

1200A, 480/277V, 3Ø

OUTSIDE INSIDE

(E)

PANEL

'EMD-6'

300A 480/277V

3Ø

400A, 480V AUTOMATIC

3-POLE TRANSFER

SWITCH

400 KVA

GENERATOR

600A, 480/277V, 3Ø

DEMO EXISTING ATS(E)

PANEL 'MSB-6H'

1200A, 480/277V, 3Ø

1200A

MCB 300A

STAIR

UP

'EMD6'(E)

'FL6'(E)

'F'(E)

'MSB-6H'(E)

LIGHTING

CONTACTOR(E)

'EM6'(E)

'UC'(E)

'D'(E)

'E'(E)

'G'(E)

EXISTING SERVICE

TRANSFORMER

REUSE

EXISTING

EMERGENCY

GENERATOR

ENCLOSURE

1200A, 480V, SERVICE

RATED AUTOMATIC

3-POLE TRANSFER

SWITCH

OWNERSHIP OF INSTRUMENTS OF

SERVICE

All Drawings, Reports, Plans, Specifications, Computer Files (including CAD files), field information, notes, sketches, and other design materials prepared by the Engineer and his/her consultants as instruments of service shall remain the property of the Engineer. The Engineer shall retain all common law, statutory and other reserved rights, including the Copyright thereto.

SHEET

FO

R

T

LY

O N

E M

ER

G

EN

C

Y G

EN

ER

AT

O

R R

EP

LA

C

EM

EN

T

C

O R

D

5, L

AS

A

N

IM

AS

C O

PROJECT #: 23-6865

DRAWN BY: JL

CHECKED BY: MRM

FULL SET ISSUE HISTORY:

REVIEW SET 06.26.20241

CLIENT:

SHEET REVISION:

cShea 4445 Northpark Dr. Suite 200 Colorado Springs, CO 80907 mcsheaconsulting.com Project #: 23-6865 onsulting, LLC

MECHANICAL + ELECTRICAL + PLUMBING

E6-1.1

ARCHITECT:

11/11/2024

90% REVIEW SET 09.25.20242

BID SET 10.11.20243

SCALE:

PROPOSED ONE-LINE DIAGRAM - BUILDING 6

E6-1.1 NONESCALE:

EXISTING ONE-LINE DIAGRAM - BUILDING 61

E6-1.1 NONE

SCALE:

EXISTING BUILDING 6 ELECTRICAL PLAN

1/8"=1'-0"E6-1.1

SCALE:

PROPOSED BUILDING 6 ELECTRICAL PLAN

1/8"=1'-0"E6-1.1

All Drawings, Reports, Plans, Specifications, Computer Files (including CAD files), field information, notes, sketches, and other design materials prepared by the Engineer and his/her consultants as instruments of service shall remain the property of the Engineer. The Engineer shall retain all common law, statutory and other reserved rights, including the Copyright thereto.

SHEET

FO

R

T

LY

O N

E M

ER

G

EN

C

Y G

EN

ER

AT

O

R R

EP

LA

C

EM

EN

T

C

O R

D

5, L

AS

A

N

IM

AS

C O

PROJECT #: 23-6865

DRAWN BY: JL

CHECKED BY: MRM

FULL SET ISSUE HISTORY:

REVIEW SET 06.26.20241

CLIENT:

SHEET REVISION:

cShea 4445 Northpark Dr. Suite 200 Colorado Springs, CO 80907 mcsheaconsulting.com Project #: 23-6865 onsulting, LLC

MECHANICAL + ELECTRICAL + PLUMBING

E8-0.1

ARCHITECT:

11/11/2024

TRANSFORMER

1200A SERVICE

RATED AUTOMATIC

3-POLE TRANSFER

SWITCH

750 KVA

GENERATOR

480/277V, 3Ø

300kVA

XFMR

XFMR

OUTSIDE INSIDE

400A

400A 480V

NEMA 3R

DISCONNECT

X

ISC = 7,484A

ISC = 42,958A

ISC = 18,798A

X X

X

ISC = 7,461A

X

ISC = 13,352A

X

ISC = 21,970A

3 3

#3/0 AL

GND. IN

"3C

REPLACE W/

LIKE FOR LIKE

1200A

MAIN

(A)

PANEL 'MDB-8L'

800A, 208/120V, 3Ø

800A

MCB

(A)

PANEL 'MDB-8H'

800A, 480/277V, 3Ø

800A

MCB

C .W

. P

IP

E

SE

R

VI

C E

G R

O U

N D

R O

D

BU

IL

D

IN

G S

TE

EL

#3 /0

#3 /0

#4 C

U

#3 /0

#3 /0

TE

LE

PH

O

N E

BO

AR

D

#6

GROUND BUS

20' MIN. CONCRETE

ENCASED ELECTRODE

EXOTHERMIC WELDED

CONNECTION

TO BLDG. No.7

ELEVATOR

'MDP'(E)

J

(E)

'FL8'(E)

ATS #2(E)'EM8'(E)

ATS #1(E)

EXISTING EMERGENCY GENERATOR

ENCLOSURE LOCATED WEST OF THIS

AREA

500KVA, 480V, 3Ø,

UTILITY

TRANSFORMER

300KVA, 3Ø, NEMA

3R TRANSFORMER

750KVA

EMERGENCY

GENERATOR

ENCLOSURE

400A, 480V

NEMA 3R

DISCONNECT

1200A, 480V, SERVICE

RATED AUTOMATIC

3-POLE TRANSFER

SWITCH

'LIGHTS'(E)

800A, 480V 'MSB-8H' (B)

800A, 208V 'MSB-4L' (A)

OWNERSHIP OF INSTRUMENTS OF

SERVICE

All Drawings, Reports, Plans, Specifications, Computer Files (including CAD files), field information, notes, sketches, and other design materials prepared by the Engineer and his/her consultants as instruments of service shall remain the property of the Engineer. The Engineer shall retain all common law, statutory and other reserved rights, including the Copyright thereto.

SHEET

FO

R

T

LY

O N

E M

ER

G

EN

C

Y G

EN

ER

AT

O

R R

EP

LA

C

EM

EN

T

C

O R

D

5, L

AS

A

N

IM

AS

C O

PROJECT #: 23-6865

DRAWN BY: JL

CHECKED BY: MRM

FULL SET ISSUE HISTORY:

REVIEW SET 06.26.20241

CLIENT:

SHEET REVISION:

cShea 4445 Northpark Dr. Suite 200 Colorado Springs, CO 80907 mcsheaconsulting.com Project #: 23-6865 onsulting, LLC

MECHANICAL + ELECTRICAL + PLUMBING

E8-1.1

ARCHITECT:

11/11/2024

90% REVIEW SET 09.25.20242

BID SET 10.11.20243

SCALE:

PROPOSED ONE-LINE DIAGRAM - BUILDING 8

E8-1.1 NONE

SCALE:

PROPOSED BUILDING 8 ELECTRICAL PLAN

1/8"=1'-0"E8-1.1