Appendix_A_-_Unit_Specifications_for_Bid_No._23-0390-ITB.pdf

Appendix Equipment and Material Specifications

Pump Stations 159 and 183

PEACEMAKER® 4X4 CONVERTING SERIES SCRUBBER

STAGE ONE – PERSNICKETY® H2S CONVERTING® MEDIA

STAGE TWO – PERSNICKETY® POLISHING® MEDIA

Odor Control Made Easy! PEACEMAKER® Converting/Polishing Dry Air Scrubbers Copyright © 2016 Syneco Systems, Inc. All Rights Reserved

AN ADVANCEMENT IN ODOR CONTROL TECHNOLOGY

PEACEMAKER® Dry Air Scrubbers provide two stage chemistry for the control of odors from hydrogen sulfide (H2S), mercaptans, ammonia, amines and other odors generated in wastewater collection and treatment systems. They are easy to use, effective and economic.

Lift Stations Headworks Grit Rooms Sludge Processing

In what follows, when we say “odor” we mostly mean H2S. We know there are other reduced-sulfur and nitrogen-based compounds involved and we have planned for them, but H2S is the main culprit and is most important in discussion and design.

OUR DESIGN PRINCIPLE…..SIMPLICITY

“The Best Solution Should be the Simplest, but Not Simpler.” — Albert Einstein

Often it is the simplest solution that works the best. Complexity is the enemy of effective, long-term odor control. Too much fussing, too many bells and whistles spell trouble.

Peacemaker scrubbers are one or two vessel fixed-bed systems, containing two stages of media.

There is one moving part, a blower. Only one thing can happen – foul air goes in, clean air comes out. There are no chemicals to add and there is no maintenance to do for the service life of the scrubber. When your Peacemaker does need attention, the entire scrubber is replaced or the media is replaced, depending upon the size of the scrubber and whether you choose to lease, buy or a service contract. But no matter how simple and easy, odor control solutions must be effective to be worthwhile.

PHONE: 952.927.9215

FAX: 952.927.9224

EMAIL: sales@synecosystems.com WEB: www.synecosystems.com

PEACEMAKER® SCRUBBERS GET THE JOB DONE

STAGE ONE – PERSNICKETY® H2S CONVERTING® MEDIA

Converting technology uses a patented polymeric amine, formulated for maximum removal of H2S and volatile mercaptans. The combination of multiple amine sites and organophilic properties allows for fast, efficient removal of these problematic compounds. This chemistry reacts with H2S and mercaptans to form water-soluble and non-volatile poly sulfides that are readily biodegradable. In simple words, gaseous H2S is turned into a stable liquid polymer. All of our scrubber systems are designed to achieve a H2S reduction of 99% through the Stage 1 media bed.

STAGE TWO – PERSNICKETY® POLISHING® MEDIA Activated carbon does a very efficient job of scrubbing low levels of H2S and other malodors. 99% of the H2S and the majority of volatile mercaptans, organic amines and organic sulfurs are removed in the converting bed.

With that being accomplished, the polishing bed will easily remove the remaining low level malodors. This results in complete and economic odor control.

PHONE: 952.927.9215

FAX: 952.927.9224

EMAIL: sales@synecosystems.com WEB: www.synecosystems.com

Odor Control Made Easy! PEACEMAKER® Converting/Polishing Dry Air Scrubbers Copyright © 2016 Syneco Systems, Inc. All Rights Reserved

CORROSION CONTROL

IT ISN’T ALWAYS JUST ABOUT ODOR

Corrosion control is a substantial secondary benefit, and in some cases it is primary. H2S accumulates in enclosed spaces. Turbulence releases it to atmosphere, but Henry’s Law is in play, too. It is not unusual to find several hundred ppm of H2S in enclosed spaces. It eventually forms sulfuric acid, a highly corrosive compound. In most cases, H2S cannot simply be exhausted into a neighborhood. But when it is continuously drawn off and scrubbed, corrosion commonly reduces by ninety percent or more, and complaints stay in check.

SIZING PEACEMAKER® SCRUBBERS

THERE ARE TWO ESSENTIAL QUESTIONS TO BE ANSWERED.

How much airflow is required? Benefits accrue from moving only enough air to maintain a slight negative pressure. This will prevent fugitive malodors and provide the best economics.

Higher-than-necessary airflow increases static pressure through the media bed and reduces residence time. A larger scrubber may be needed and cost would increase.

PHONE: 952.927.9215

FAX: 952.927.9224

EMAIL: sales@synecosystems.com WEB: www.synecosystems.com

Odor Control Made Easy! PEACEMAKER® Converting/Polishing Dry Air Scrubbers Copyright © 2016 Syneco Systems, Inc. All Rights Reserved

To calculate optimum airflow we must determine the potential for air displacement (e.g. gpm pumped into a wet well). Of course, if there is an air exchange requirement for confined space entry or a need for higher airflow for any other reasons, it can be accommodated.

LEASE, BUY OR SERVICE CONTRACT

Lease The length of “term” for most PEACEMAKER® leases is one to three years. At the end of term, we provide a new scrubber, if you wish, and you return the old one to us, freight collect. If conditions change from one term to the next, we can change the new scrubber to match the new conditions. You will never be stuck with out-grown and useless equipment.

In addition, our lease agreement is like our scrubbers — simple and straightforward.

Buy If your PEACEMAKER® needs to come from a capital budget, this is obviously the way to

go. It will still be a great value. Lease or buy, labor and maintenance costs will be minimal.

There just is not much to do once the scrubber is up and running besides enjoying the nice clean air and the very quiet phone.

Service Contract The length of “term” for most PEACEMAKER® service contracts is three to five years.

With a service contract, H2S loadings and CFM would have to be well documented and we would guarantee the life of the scrubber system for the life of the service contract based on those levels.

How much H2S is in that air? This can be a difficult question to answer. It can be influenced by time of day, time of year, residence time, measuring techniques and numerous additional factors.

Truth is it is hard to escape applying some judgment in making this determination. Experience helps, of course, but Peacemaker systems have built-in flexibility and scalability, which helps, too. Ultimately, the formula is simple: cfm airflow x ppm H2S = quantity of media required.

This is an important process, and we need to work together. We start with a review of “PEACEMAKER® Converting/Polishing Dry Air Scrubber Sizing Information.”

AVAILABLE SIZES

When we have determined the quantity of media required, we simply match that need to the correct vessel size and add the right fan to provide desired airflow at the existing static pressure.

PHONE: 952.927.9215

FAX: 952.927.9224

EMAIL: sales@synecosystems.com WEB: www.synecosystems.com

Odor Control Made Easy! PEACEMAKER® Converting/Polishing Dry Air Scrubbers Copyright © 2016 Syneco Systems, Inc. All Rights Reserved

Limited Warranty:

Our only obligation shall be to replace or pay for any material proved defective. Beyond the purchase price of materials supplied by us, we assume no liability for damages of any kind and the user accepts the product “as is” and without warranties, expressed or implied. The suitability of the product for an intended use shall be solely up to the user.

7945 STONE CREEK DR STE 50

CHANHASSEN MN 55317

PHONE: 952.927.9215

FAX: 952.927.9224

EMAIL: sales@synecosystems.com

PEACEMAKER® 4x4 Converting Series Scrubber Copyright © 2016 Syneco Systems, Inc. All Rights Reserved

PEACEMAKER® 4X4 CONVERTING SERIES SCRUBBER

FAN See “VBW-6 FAN SPECIFICATIONS” for details.

PHYSICAL

Vessel 1.9 SG Black/White HDPE

Cover 1/4″ Black/White ABS

Influent Coupling (Foul Air Intake) 4″ Diameter

Lower Air Diffuser Molded 1/4″ ABS

Height (without fan) 55-1/2″

Diameter 48

Media (maximum) 48 Cu-Ft

Foot Print 48″x54″

Charged Weight 2,600lbs.

Airflow (maximum) 200 CFM

Fan (maximum) VBW-6

MISCELLANEOUS

Storage/Use Store and use away from acids and reducing agents. Do not add any chemicals to the scrubber other than those recommended by the manufacturer. Syneco Systems reserves the right to change specifications without prior notice. In no case will such changes have an adverse effect on the performance of the product.

PHONE: 952.927.9215

FAX: 952.927.9224

EMAIL: sales@synecosystems.com WEB: www.synecosystems.com mailto:sales@synecosystems.com mailto:sales@synecosystems.com http://synecosystems.com/wp/products-information/equipment/equipment-data/550c-ng/ outline dimensions:

[note: motor shown is for 50Hz performance.

Motor dimensions for 60Hz operation may vary]

Motor type:

Squirrel cage induction motor IP44 as std, IP55 available nominal supply:

220/240V or 115V 1Ph 50Hz

115/230V 1Ph 50/60Hz

380/420VY / 220/240VD 3Ph 50Hz

440/480VY / 250/280VD 3Ph 60Hz options:

Inlet & discharge guards, Inlet filters, Spigots

Materials:

Fancase: Cast aluminium LM6

Impellers: Galvanised sheet steel

Finishes: Unpainted/Stove enamel (black) as std

Mounting options: Motor feet or Pedestal noise levels: 76.5dB(A) Free Air, 1M

Weight: 6Kgs / 13Lbs

Motor Variations: ATEX, CE, CSA, UL available

Please note (1) - all drawings measurements are in millimeters (mm) Please note (2) - above technical specifications are subject to change

VBL-6 FAN SPECIFICATIONS

[Please note - image above may not be representative of the unit supplied]

VBL6 Fan Specifications Copyright © 2016 Syneco Systems, Inc. All Rights Reserved Page 1

PHONE: 952.927.9215

FAX: 952.927.9224

Syneco Systems, Inc.

7945 Stone Creek Drive, Suite 50

Chanhassen, MN 55317 Tele: 952-927-9215

Fax: 952-927-9224

E-mail: sales@synecosystems.com

Syneco Systems Peacemaker Dry Air Scrubber Media Refill Instructions

Media Change Instructions:

Please note that the bags have been marked/identified by the factory as to their designated scrubber and order of placement.

Procedure:

• Remove Fan.

• Remove all screws from the top cover of the Peacemaker Odor Control System.

• Add register marks to cover and tank for proper realignment after refill. Remove cover and inspect gasket material.

• Remove the bridge by lifting up on one end and pulling it out.

• Remove old media with use of Vacuum Truck or Shoveling / Scooping out media.

• Inspect Diffusing Chamber and tank for proper fitment.

• Add Converting Media First (Bottom Layer). Add to the middle of the tank and then spread Media evenly to the sides of the tank (this is imperative so that you do not cause tank distortion). Smooth flat.

• Add Polishing Media (Top Layer). Add to the middle of the tank and then spread Media evenly to the sides of the tank. Smooth flat.

• Add the bridge back in to place.

• Add the Tank Cover to the tank and line the cover to the tank with use of the register marks.

• Add all the Screws the cover for an air tight seal.

• Add Fan back to the effluent flange and secure in to place.

Further Questions:

Please Contact Syneco Systems at sales@synecosystems.com or please call (952)927-9215.

Thank you!

Syneco Systems Inc PERSNICKETY® BRAND CONVERTER MEDIA SDS pg. 1 www.synecosystems.com

PHONE: 952.927.9215

FAX: 952.927.9224

EMAIL: sales@synecosystems.com

Current as of 09/16/2015

Section 1: Product and Company Identification Product Name: PERSNICKETY® BRAND CONVERTER MEDIA Family Name: Oxidizing Media for Odor Control Company Name: Syneco Systems, Inc.

Telephone Numbers: Emergency: (CHEMTREC): 1-800-424-9300 Product Information: 952-927-9215 (Monday-Friday 8:00 am – 4:30 pm CST)

Section 2: Hazards Identification Potential Health Effects EYES: May be irritating/corrosive.

SKIN: May be irritating/corrosive.

INGENSTION: May be harmful if swallowed. It can irritate nose and throat.

INHALATION: May be irritating to eyes and respiratory tract.

Section 3: Compositions/Information on Ingredients The specific identities of certain components of this formulation are withheld as trade secrets.

COMPONENT CONCENTRATION

Component A 61 % Component B 9.5 %

Section 4: First-Aid Measures Eyes: Immediately wash eyes with water for at least 15 minutes. Lift upper and lower lids and rinse well under them. Get immediate medical attention.

Skin: Wash with soap and water. If irritation persists get medical attention.

Ingestion: Do not induce vomiting. Do not give anything by mouth to an unconscious person. Immediately drink large quantities of water or milk. Get medical attention.

Section 5: Fire-Fighting Measures Flammable Properties: This product is non-flammable.

Flash Point: None Flammable Limits: N/A The product is non-flammable.

Extinguishing Media: Water fog.

Fire & Explosion Hazards: This product is not combustible unless it comes in direct contact with acids and organic material while in use or in disposal of spent material.

Fire Fighting Equipment: Wear full bunker gear including a positive pressure self-contained breathing apparatus.

Section 6: Accidental Release Measures Scoop up spilled dry material and place in an appropriate container for disposal. If the material is wet, the spill area must be rinsed thoroughly, as a corrosive residue may remain. Do not allow spilled wet material to evaporate to dryness.

Section 7: Handling and Storage Store in a cool, dry place. Do not allow material to get wet, as a corrosive solution may result. Store separately from acids, reducing agents, organic material such as solvents, fuel, wood (i.e. pallets) and paper. Do not store in steel drums. After handling, wash hands with soap and water.

Syneco Systems Inc PERSNICKETY® BRAND CONVERTER MEDIA SDS pg. 2

PHONE: 952.927.9215

FAX: 952.927.9224

Section 8: Exposure Controls/Personal Protection Engineering Controls: Ensure adequate ventilation, especially in confined areas.

Personal Protective Equipment:

Respiratory Protection: If dust is present or in confined spaces wear a NIOSH/MSHA approved Respirator with an organic vapor cartridge.

Skin protection: Wear chemical resistant gloves.

Eye protection: Wear safety glassed or gloves.

Exposure guidelines: PEL/TLV has not been established for the product as a whole.

COMPONENT OSHA PLE/TWA ACGIH TLV/TWA

Amorphous Silica 15 (total dust) 10 (total dust) Crystalline Silica (Quartz) 1.0 mg/m3 (as respirable dust) 0.05 (as respirable dust)

Section 9: Physical and Chemical Properties Appearance: Tan colored granular solid.

Flammability: Non-flammable Odor: Amine/ammonia odor.

pH: 10-11 Melting/Freezing Point: N/A Boiling Point: N/A Weight: 50 lbs./cu.ft.

Solubility: Not soluble.

Section 10: Stability and Reactivity Stability: This product is stable under normal storage conditions.

Conditions to avoid: Stable under normal conditions.

Incompatibility: Organic, combustible materials, decomposed acids, oxidizing agents, exposure to direct sunlight.

Hazardous Decomposition Products: Oxides of carbon and nitrogen.

Chemical stability This product is stable under normal storage conditions.

Other Hazardous reactions: Contact with acids, organic materials, reducing and oxidizing agents will release chlorine and/or chlorine gas.

Section 11: Toxicological Information

Toxicological testing data is not available for the product as a whole. The following information is provided by combining information from individual components.

Routes of Exposure Eye: May cause irritation if dust gets in the eye.

Skin: Not absorbed by the skin but may cause dryness or irritation with prolonged exposure.

Ingestion: Ingestion of small quantities is not considered harmful but may cause irritation of the mouth, throat and stomach.

Inhalation: Acute inhalation can cause irritation of the nasal passage and lung congestion, coughing and general throat irritation.

Chronic Effects: This product contains a small amount of naturally occurring crystalline silica. Respirable crystalline silica may cause lung cancer and lung disease if inhaled for prolonged periods.

Chronic inhalation of dust should be avoided.

Syneco Systems Inc PERSNICKETY® BRAND CONVERTER MEDIA SDS pg. 3

PHONE: 952.927.9215

FAX: 952.927.9224

EMAIL: sales@synecosystems.com

Carcinogenicity: This product is partially composed of amorphous silica, but can contain a small fraction (<1%) of crystalline silica. Respirable crystalline silica is classified by IARC and NTP as a known human carcinogen. Crystalline silica only causes cancer when inhaled in a respirable form. It does not cause cancer by any other route of exposure.

Section 12: Ecological Information Persistence and Degradability: Non-biodegradable.

Bioaccumulative Potential: Little potential for bioaccumulation.

Mobility in Soil: No mobility.

Section 13: Disposal Considerations Waste Disposal: Disposal is as a solid waste. Treatment, storage, transportation, and disposal must be in compliance with local, state and federal laws and regulations. Contact local or state environmental agency for specific regulations.

Section 14: Transport Information DOT Shipping Name: Not regulated.

UN ID Number: N/A Hazard Class: Non-hazardous for D.O.T purposes.

Section 15: Regulatory Information OSHA Hazard Communication Rule, 29 CFR 1901.1200:

According to the OSHA Hazard Communications standard, this product is considered hazardous because it contains Component B and trace amounts of crystalline silica.

CERLA/SUPERFUND, 40 CFR 117.302: This compound contains NO compounds subject to 40 CFR 117.302.

SARA 313 Information: This product contains the following toxic chemicals subject to the reporting requirements of section 313 of the Emergency Planning Community Right-To-Know Act of 1986 and of 40 CFR 372: NONE

Toxic Substances Control Act (TSCA): The ingredients of this product are all on the TSCA Inventory List.

California Proposition 65: The following statement is made in order to comply with the California Safe Drinking Water and Toxic Enforcement Act of 1985:

“Notice: This product contains a chemical known to the state of

California to cause cancer, birth defects, or other reproductive harm.”

[22 CCR 12705 (b)]. This product contains CRYSTALLINE SYLICA.

Section 16: Other Information

NFPA RATING HMIS RATING

Fire 1 Health 1 Health 1 Flammability 1 Reactivity 0 Reactivity 1 Hazard 0 Protection B This data is furnished gratuitously independent of any sales of the product and only for your investigation and independent verification. While the information is believed to be correct, Syneco Systems, Inc. shall in no event be responsible for any damages whatsoever, directly or indirectly, resulting from the publication, use of, or reliance upon the data contained herein. No warranty, either expressed or implied, of merchantability, of fitness, or of any nature with respect to the product, or to the data is made herein.

Syneco Systems Inc PERSNICKETY® BRAND CONVERTER POLISHING MEDIA SDS pg. 1

FAX: 952.927.9224

EMAIL: sales@synecosystems.com WEB: www.synecosystems.com

Current as of 10/29/2015

Section 1: Product and Company Identification Product Name: PERSNICKETY® BRAND CONVERTER POLISHING MEDIA Family Name: Oxidizing Media for Odor Control Chemical Name: Activated Carbon Synonyms: Coconut Shell Base Activated Carbon Company Name: Syneco Systems, Inc.

Telephone Numbers: Emergency: (310) 885-4555 Product Information: 952-927-9215 (Monday-Friday 8:00 am – 4:30 pm CST)

Section 2: Hazards Identification OSHA Regulatory Status - Not Regulated Health Effects - Prolonged over exposure to carbon dust can produce skin and eye irritation.

-Prolonged inhalation can cause irritation of mucus membranes.

(See Sections IV & XI)

HMIS INDEX:

HMIS Index details are as follows;

HEALTH: 0

FLAMMABILITY: 1

REACTIVITY: 0

PPE: E

GHS CLASSIFICATION

NOTE: Health effects comments refer to the pure component knowing that the concentration on the carbon is significantly less than 100%.

Hazard Symbol Hazard/Category Warning Respiratory Irritation Category 3 Dust causes respiratory, skin and eye irritation.

Eye Irritation 2A

Prolonged or repeated inhalation or ingestion can cause irritation of mucous membranes.

Wet activated carbon removes oxygen from air causing a severe hazard to workers in enclosed or confined space.

PRECAUTIONARY STATEMENTS-

Prevention Avoid generation of dust during handling.

The dust or fines may be more susceptible to catalytic reaction than the large mesh product.

Avoid breathing dust.

Wash thoroughly after handling.

Use in a well ventilated area.

Avoid release to environment.

Response IF INHALED: Remove to fresh air and keep at rest in a position comfortable for breathing.

Seek Medical attention for any breathing difficulty.

IF IN EYES: Rinse cautiously with water for several minutes. Seek medical attention if irritation persists.

CONTACT WITH SKIN: Remove contaminated clothing. Rinse cautiously with soap and water for several minutes. Seek medical attention if irritation persists.

IF INGESTED: Drink a large volume of water; seek medical attention.

Storage Store in a well-ventilated place.

Keep container tightly closed.

Syneco Systems Inc PERSNICKETY® BRAND CONVERTER POLISHING MEDIA SDS pg. 2

FAX: 952.927.9224

EMAIL: sales@synecosystems.com WEB: www.synecosystems.com

Section 3: Compositions/Information on Ingredients Chemical Name (CAS#) % PEL (OSHA) TLV(ACGIH) Other Carbon* (7440-44-0) 100 N/A N/A N/A

*ACGIH (TWA) for reparable dust is 2.5 mg/m3

There are no established PEL, TWA or TLV values for this material. Caution should be taken for respirable dust. The product has no known carcinogenic properties.

Non-Hazardous components are recorded at 3% or >; Acute hazards are recorded when present at 1% or >; Chronic hazards are recorded when present at 0.01% or >.

This is not intended to be a comprehensive compositional disclosure.

Section 4: First-Aid Measures In ease off ingestion do not induce vomiting. Dilute by giving water or milk. Seek medical attention.

In case of inhalation remove to fresh air. Administer first aid as appropriate. Seek medical attention.

In case of skin contact, wash thoroughly with soap and water. If irritation persists seek medical attention.

In case of eye contact flush with lukewarm water for at least 15 minutes. Lift upper and lower eye lids occasionally.

Seek medical attention.

OTHER:

The effects of chronic and sub-chronic exposure have not been determined. Safe handling on a long-term basis should emphasize protection against respective or long-term exposure to carbon dust inhalation and avoidance of contact to any liquids that may leach off the impregnated carbon. Affected individuals with pre-existing conditions pertaining to digestive, respiratory, skin or eye problems can be more susceptible to potential effects of carbon dust.

HEALTH HAZARD DATA:

Route (s) of Entry:

Ingestion: Carbon is non-toxic through ingestion. Dust may cause mild irritation to the digestive tract resulting in nausea or diarrhea.

Inhalation: The physical nature of carbon may irritate the respiratory system. Dust may cause mild irritation to the upper respiratory tract

Skin: Carbon is non-toxic through skin absorption. Dust may cause mild irritation probably reddening.

Eye Irritation: The physical nature of carbon may cause eye irritation. Dust may cause mild irritation probably reddening.

Section 5: Fire-Fighting Measures Flash Point: N/A Extinguishing media: Alcohol foam, CO2, dry chemical, water.

Special Firefighting procedures: Exercise caution when responding to any chemical fire.

Respiratory protection is essential.

Decomposition Products: CO may be formed in fire.

Thermal Decomposition: Sulfur Oxides (SOx)

FIRE FIGHTING MEASURES:

Flashpoint: Not Applicable.

Non-flammable: 16CFR1500.44.

Not Self Heating: UN Manual of Tests and Criteria, Test N.3.

Syneco Systems Inc PERSNICKETY® BRAND CONVERTER POLISHING MEDIA SDS pg. 3

Flammability Limits in Air: LFL and UFL Not Applicable.

GENERAL HAZARD: Carbon Monoxide and Carbon Dioxide gas may be generated during combustion. Caution is advised.

Contact of activated carbon with strong oxidizers such as ozone or liquid oxygen may cause rapid combustion.

Fire is possible at elevated temperatures or by contact with an ignition with most types of organic solids. Activated carbon is difficult to ignite and when it does, it has a tendency to burn or smolder very slowly without any smoke or flame.

Toxic gases will form upon combustion.

FIRE FIGHTING INSTRUCTIONS: If possible to do safely, move smoldering activated carbon to a non-hazardous area, preferably out of doors. Extinguish fire using water fog, fine water spray, carbon dioxide or foam. Avoid stirring up dust clouds.

FIREFIGHTING EQUIPMENT: Firefighting personnel should wear full protective equipment, including self-contained breathing apparatus (SCBA) for all inside fires and large outdoor fires.

HAZARDOUS COMBUSTION PRODUCTS: Combustion products may include smoke and oxides of carbon (for example, carbon monoxide). Materials allowed to smolder or long periods in enclosed spaces, may produce amounts of carbon monoxide which reach the lower explosive limit (carbon monoxide LEL = 12.5% in air). Under certain conditions, any airborne dust may be an explosion hazard. Used activated carbon may produce additional combustion products.

Section 6: Accidental Release Measures

Reportable Quantities: No EPA requirements.

Personal Precautions: Wear protective equipment, keep unnecessary personnel away, and ventilate area of spill.

Environmental Precautions: The carbon is not soluble in water; however, dust particles can cause a particulate emission if discharged to waterways.

Block all entrances to sewers and drains to avoid introducing the material into the waterways.

Steps To Be Taken For Containment & Clean-up: Block all entrances to sewers and drains.

Vacuum, shovel or sweep up spilled material, neutralize and place in closed container for disposal.

Do not release to sewer or waterway Remove product to appropriate storage area until it can be properly disposed of in accordance with local, state and federal regulations.

Avoid formation of dust.

Waste Disposal Method: Unused product may have a lot pH.

Used product may contain hazardous chemicals or hazardous properties that may have to be examined to determine proper disposal method.

Dispose in accordance with local, state, and federal regulations.

Syneco Systems Inc PERSNICKETY® BRAND CONVERTER POLISHING MEDIA SDS pg. 4

FAX: 952.927.9224

EMAIL: sales@synecosystems.com WEB: www.synecosystems.com

Disposal Considerations: Activated carbon, in its original state, is not a hazardous material or hazardous waste. Follow applicable governmental regulations for waste disposal.

Used activated carbon may become classified as a hazardous waste depending upon the application.

Follow applicable regulations for disposal.

Recycling (reactivation) may be a viable alternative to disposal.

Section 7: Handling and Storage Storage Temperature: Ambient

Storage Pressure: Atmospheric

Handling: Follow good handling and housekeeping practices to minimize spills, generation of airborne dusts, and accumulation of dusts on exposed surfaces.

Use with adequate exhaust ventilation to draw dust away from workers' breathing zones.

Keep away from ignition sources.

Use in well ventilated areas.

Protect containers from physical damage.

Avoid prolonged contact with eyes and skin.

Prevent or minimize exposures to dusts by using appropriate personal protection equipment

Avoid Wash exposed skin areas thoroughly with soap and water after handling.

Storage: Dry airtight storage recommended.

Store in cool, dry, ventilated area and in closed containers.

Maintain good housekeeping.

Store away from strong oxidizers such as ozone, liquid oxygen, chlorine, permanganate, etc.

Keep away from heat or flames or ignition sources.

Section 8: Exposure Controls/Personal Protection Respiratory Protection: Use NIOSH/MSHA approved respiratory protection equipment appropriate to the material and/or its concentration where airborne exposure is likely. If exposures cannot be kept to a minimum with engineering controls, consult respirator manufacturer to determine appropriate type equipment for a given application. Observe respirator use limitations specified by NIOSH/MSHA or the manufacturer.

Ventilation/Local Exhaust: Essential in confined areas Eye Protection: Safety glasses or goggles with side shields are recommended for any type of handling. Where eye contact or dusty conditions may be likely, dust tight goggles are recommended. Have eye flushing equipment available.

Skin Protection: Avoid contact with the skin. Wear appropriate dust resistant clothing. Wash contaminated clothing and clean protective equipment before reuse. Wash skin thoroughly after handling. Protective gloves are recommended.

Airborne Exposure Guidelines: Recommended Exposure Limits Activated Carbon 8-hr TWA

Syneco Systems Inc PERSNICKETY® BRAND CONVERTER POLISHING MEDIA SDS pg. 5

Total Dust 10 mg/m3* Respirable Fraction 3 mg/m3*

EXPOSURE CONTROL:

NOTE: PEL, TLV and Toxicological data when available are provided for the pure component knowing that the carbon product contains a lesser percentage.

Component *Activated Carbon

OSHA ACGIH Other Limits

PEL TLV

Data not available Data not available

Exposure Guidelines Wet activated carbon removes oxygen from air posing a hazard to workers in enclosed or confined space.

Before entering such an area, sample the air within to assure sufficient oxygen supply. Use work procedures for low oxygen levels, observing all local, state and federal regulations. Comment: Remove from the area any worker who shows allergic reactions from exposure to sulfur.

Engineering Controls Exhaust ventilation should be designed to prevent accumulation and recirculation in the workplace and safely remove carbon black from the air.

Note: Wet activated carbon removes oxygen from air causing a severe hazard to workers in enclosed or confined space. If risk of overexposure exists, wear an approved respirator. Provide adequate ventilation in warehouse or closed storage area.

Personal Protective Equipment Use of NIOSH approved particulate filter is recommended if dust is generated in handling. The usual precautionary measures for handling chemicals should be followed, i.e. gloves, safety glasses w/side shields or goggles, long sleeve shirt or lab coat, dust respirator if dusty and/or other protective clothing/equipment as determined appropriate.

General Hygiene The usual precautionary measures for handling chemicals should be followed: i.e. Keep away from food and beverage; remove contaminated clothing immediately; wash hands before breaks or eating; avoid contact with eyes and skin.

*OSHA and ACGIH have not established specific exposure limits for this material. The recommended exposure limits for these activated carbon products are based on the Threshold Limit Values adopted by ACGIH for Particulates (insoluble) Not Otherwise Classified.

The OSHA PEL for Nuisance Dust is 15 mg/m3 (5 mg/m3 respirable fraction).

Section 9: Physical and Chemical Properties Appearance: Granular, powder of extruded pellet Odor: None Color: Black pH Value: 7-10 Specific Gravity, (H2O = 1): 3.5 Solubility in water: Insoluble Vapor Pressure: 0 Vapor Density: Solid Relative Density: 0.4 – 0.7 Flammability: > 220O C Auto Ignition Temperature: > 220O C Melting Point: N/A

Syneco Systems Inc PERSNICKETY® BRAND CONVERTER POLISHING MEDIA SDS pg. 6

FAX: 952.927.9224

EMAIL: sales@synecosystems.com WEB: www.synecosystems.com

Boiling Point: N/A Freezing Point: N/A Flash Point: N/A Evaporation: N/A Molecular Weight: N/A

Section 10: Stability and Reactivity Chemical Stability : This product is stable under normal storage conditions.

Conditions to Avoid : None Possibility of Hazardous Reaction :

Will Not Occur

Conditions to Avoid : None Incompatibility / Materials to Avoid :

Strong oxidizers such as oxygen, ozone, chlorine, permanganates, etc…alkali metals, liquid acids.

Hazardous Decomposition Products :

Carbon monoxide and carbon dioxide gas can be generated if combustion of this material takes place.

Sulfur oxides emission is possible during combustion.

Caution: High concentrations of organics in air will cause temperature rise due to heat of adsorption. At very high concentration levels this may result in a thermal excursion, referred to as a bed fire. High concentrations of Ketones and Aldehydes may cause a rise in bed temperature due to adsorption and oxidation.

Section 11: Toxicological Information NOTE: Toxicological data is provided for the pure component knowledge that the carbon product contains a lesser %

ACUTE EFFECTS

Toxicity Studies Oral LD50 Not determined on the finished product.

Dermal LD50 Not determined on the finished product.

Inhalation See section IV - Ingestion See section IV - Eye Irritation See section IV - Skin Irritation See section IV - Target Organs or Systems Eyes, skin, and upper respiratory system Signs and Symptoms of Exposure See section III & IV Irritation and redness of eyes, irritation of skin and respiratory system may result from exposure to carbon dust.

CHRONIC EFFECTS

Carcinogenicity Not determined on the finished product

Mutagenicity Not determined on the finished product

Reproductive Effects Not determined on the finished product

Developmental Factors Not determined on the finished product

Section 12: Ecological Information NOTE: Ecological data is provided for the pure component knowledge that the carbon product contains a lesser %.

Ecotoxicity Not determined on the finished product.

Mobility in Environmental Media Not determined on the finished product.

Bioaccumulation/Accumulation Not determined on the finished product.

Persistence/Degradability Not determined on the finished product.

Any Other Adverse Effects Not determined on the finished product.

Syneco Systems Inc PERSNICKETY® BRAND CONVERTER POLISHING MEDIA SDS pg. 7

FAX: 952.927.9224

EMAIL: sales@synecosystems.com WEB: www.synecosystems.com

Section 13: Disposal Considerations See Section VI

Storage and disposal should be in accordance with applicable local, state and federal laws and regulations.

Activated Carbon is an adsorbent media; hazard classification is generally determined by the adsorbate that the carbon has picked up.

Consult with the US EPA Guidelines as per 40 CFR Part 261.3 for the classifications of hazardous waste before disposal.

Section 14: Transport Information USDOT (United States Department of Transportation) Regulations Proper Shipping Name: Steam Activated Carbon, Non-Regulated OR Carbon, Activated, Non-Regulated Shipping Class: Class 70 Hazard Class: Not Applicable See *Note Below UN/NA Number: Not Applicable Packing Group: Not Applicable Freight Classification: STCC Code - #2899643 / NMFC #40560 DOT Marking: Not Applicable DOT Placard: Not Applicable Precautions To Be Taken In Transportation: No specific precautions

See Section

Section 15: Regulatory Information

US FEDERAL REGULATIONS

OSHA (29 CFR1910:1200): Not Regulated

See Table Z-1 of 29CFR1910.1000, Limits For Air Contaminates.

CERCLA/SUPERFUND (40CFR117, 302): Contains no CERCLA hazardous substances.

Notification of spills of this material is not required Specific reporting requirements at the local, regional, or state level pertaining to releases of this material may exist.

RCRA (40CFR261.33, 261.20-24): This product, in its original state, does not meet the criteria of hazardous waste.

Toxic Substances Control Act (40CFR710): Activated carbon does not contain any relevant components.

Clean Water Act (40CFR122.21 and 40CFR122.42):

Activated carbon does not contain any substances regulated as pollutants.

Clean Air Act (CAA, Section112, 40CFR82):

Activated carbon does not contain any components listed as Hazardous Air Pollutants, Flammable Substances, Toxic Substances, or Class 1 or 2 Ozone Depletors.

California Prop. 65 Product and impregnate component are not listed.

Section 302 - Extremely Hazardous Substances

(40CFR355):

This product is not listed as an extremely hazardous substance.

SECTION 313-

List of Toxic Chemicals:

This product is not listed.

Amendments and Reauthorization Act of 1986 (Title III), Sections 302, and 313

SARA 311/312 Hazard Categories Acute Health Hazard Chronic Health Hazard Fire hazard

NO

NO

NO

NO

NO

Syneco Systems Inc PERSNICKETY® BRAND CONVERTER POLISHING MEDIA SDS pg. 8

FAX: 952.927.9224

EMAIL: sales@synecosystems.com WEB: www.synecosystems.com

Sudden release of pressure hazard Reactive Hazard

NO

NO

Activated carbon, (CAS: 7440-44-0) is found on the following regulatory lists:

US EPA High Production Volume Program Chemical List US FDA CFSAN Color Additive Status List 4 US FDA CFSAN Color Additive Status List 6 US DOE Temporary Emergency Exposure Limits (TEELs) US - Hawaii Air Contaminant Limits US - Idaho - Toxic and Hazardous Substances - Mineral Dust US - Minnesota Hazardous Substance List US - Minnesota Permissible Exposure Limits (PELs) US - Rhode Island Hazardous Substance List US - Vermont Permissible Exposure Limits Table Z-1-A Final Rule Limits for Air Contaminants US - Washington Permissible exposure limits of air contaminants Canada - British Columbia Occupational Exposure Limits Canada - Yukon Permissible Concentrations for Airborne Contaminant Substances Canada Domestic Substances List (DSL) International Air Transport Association (IATA) Dangerous Goods Regulations OECD Representative List of High Production Volume (HPV) Chemicals

CANADIAN CLASSIFICATION

WHMIS (CPR, SOR/88-66): Product and impregnate component are listed

DSL #. Product and impregnate component are listed

EEC Council Directives relating to the classification, packaging, and labeling of dangerous substances and preparations

Risk and Safety Phrases R36: Irritating to the eyes R37: Irritating to the respiratory system R38: Irritating to the skin

Section 16: Other Information This data is furnished gratuitously independent of any sales of the product and only for your investigation and independent verification. While the information is believed to be correct, Syneco Systems, Inc. shall in no event be responsible for any damages whatsoever, directly or indirectly, resulting from the publication, use of, or reliance upon the data contained herein. No warranty, either expressed or implied, of merchantability, of fitness, or of any nature with respect to the product, or to the data is made herein.

Note: The recommended C.F.M.'s may change over time according to conditions at the specific air scrubber location.

MONTHY INSPECTIONS

* Inspect the fan and all electrical connections. Check the air flow.

The Peacemaker should not require any maintenance. However, regular inspections should be performed to insure continued complete odor control.

PEACEMAKER DRY AIR SCRUBBER

Installation Date:

PEACEMAKER LOCATION

SYNECO SYSTEMS, INC.

Web site: www.synecosystems.com

E Mail: sales@synecosystems.com

Phone: 952-927-9215

* Check the condensate drain to insure that any condensate water is draining properly.

* Inspect the scrubber tank and all plumbing connections.

http://www.synecosystems.com/ http://www.synecosystems.com/ http://www.synecosystems.com/ http://www.synecosystems.com/ http://www.synecosystems.com/ http://www.synecosystems.com/ http://www.synecosystems.com/

Syneco Systems, Inc.

7945 Stone Creek Drive, Suite 50

Chanhassen, MN 55317 Tele: 952-927-9215

Fax: 952-927-9224

E-mail: sales@synecosystems.com

Startup Checklist / Instructions 1: The Peacemaker Odor Control System will be delivered on a temporary pallet.

2: The Peacemaker Odor Control System needs to be taken off the truck and set in to place. This can be done with a boom truck, forklift, or bobcat.

3: The Blower, Blast Gate, and Condensate Hosing will come in a box in side of the Peacemaker Odor Control System. Please remove the tank cover so media can be added.

4: Media: It’s important to empty each media superbag in the center of the tank.

The Converting Media goes in first. Once added, even the material out. Add the secondary Polishing Media. Once added, ever the material out, clean off any media that might be along the top rim of the tank before adding the tank.

5: The vent from the needs to be plumbed / ducted to the blast gate (which is already preset for to the correct airflow).

6: The blast gate will need to be attached to the influent coupling of the

Peacemaker Odor Control System.

7: Once the system is in place and plumbed properly, the Blower will need to be taken out of the box and added to the top of the Peacemaker.

8: Once attached, the Blower will need to be plugged in and turned on.

9: The Condensate hose will need to be screwed in to the Peacemaker with the hose barb fitting to the lower right of the Influent Coupling. Syneco Systems, Inc recommends that the condensate hose drains back in to the waste stream.

10: The Peacemaker Odor Control System will now be fully operational.

11: Installation Instructions are attached.

12: The Media Change / Refill Instructions are attached.

13: Contact Syneco Systems, Inc with any questions at (952)927-9215.

Pump Stations 110 and 196 Ecosorb® 130 CFM Vapor Phase Unit

Technical Data Sheet

The OMI 130 CFM unit uses vapor phase dispersion to produce sub-micron particles for the highest efficiency possible when used with Ecosorb® Odor Neutralizer.

Made of 16-gauge powder coated steel with a durable locking handle, the unit can be bolted to the concrete pad or to a uni-strut rack. The unit has been designed to stand up to the outside elements, but can also be used indoors.

This self-contained system requires only a power supply, which means no filters, complicated mixing equipment, pumps or nozzles. Simply pour 5 gallons of Ecosorb into the product supply tank, lock the door, and walk away. After 21-30 days of use, drain the product tank and add another 5 gallons of Ecosorb. Otherwise maintenance is limited to rinsing the product storage tank out every six months.

heat dissipation

*Ecosorb® is a trademark of OMI Industries. REV 12-20-12

Ecosorb® 130 CFM Vapor Phase Unit

IDEAL FOR:

TECHNICAL SPECS

One Corporate Drive, Suite 100

www.omi-industries.com

Ecosorb® Remarkably effective. Surprisingly simple.

Pump Station 72 Engineered Air

Model Number LM1/O/MV/GH1

SUBMITTAL RECORD

JOB NAME: PS072 DK8547(OF315)JOB NO:

CUSTOMER: ENGINEER:KLOOTE CONTRACTING, INC. METZGER WILLARD, INC.

EngA MODEL: QTY: TAG:LM1/O/MV/GH1 1 OX1

SHIPPING AND APPROVAL INFORMATION

MOUNTING Outdoor Base Mounted ACCESS As Per Drawing

OPERATING WEIGHT 2370 lbUNIT MINIMUM AMBIENT 20°F SHIPPING WEIGHT 2420 lb

NO. OF PIECES 2 (Unit + Exhaust Stack)

• Intertek ETLus approval.

•GH1 is sized to neutralize 7.1 g/hr of H2S.

EXHAUST AIR DATA

AIR FLOW 375 CFM FAN SIZE (1) 805F JRW CL SD TSP 1.5 in w.c. RPM 2555

MOTOR SIZE 1/2 HP TYPE (RPM) TEFC (3450) ESP BHP 0.24 BHP

•Exhaust air fan/motor c/w epoxy coated assembly.

•Exhaust air consist of 300 CFM oxidant air and 75 CFM foul air.

AIR OPENING DATA

AIR OPENING LOCATION DAMPER TYPE OPERATION

EXHAUST AIR See Below [1] FOUL AIR Bottom OUTSIDE AIR Bottom

• [1] See Mechanical Drawing •Foul air connection c/w 4" Dia PVC Connection

CONSTRUCTION DATA

UNIT CABINET 18 gauge 316 stainless steel sheet metal c/w 2" 3 lb/ft³ insulation on entire unit casing.

UNIT LINER 22 gauge 316 stainless steel solid liner throughout including unit underside.

UNIT FLOOR 18 gauge 316 stainless steel sheet metal on entire unit floor.

Floor c/w floor drain connection through floor (see mechanical drawing for locations)

AIRSIDE DOOR All access stainless steel hinged c/w padlockable stainless steel lever type door handles

SERVICE DOOR Electrical access stainless steel hinged c/w padlockable stainless steel lever type door handles

•316 stainless steel air mixer (see mechanical drawing).

ELECTRICAL DATA

POWER SUPPLY MINIMUM CIRCUIT AMPACITY MAXIMUM FUSE(D.E.) MAXIMUM BREAKER

120 / 1 / 60 32.0 AMPS 40 AMPS 40 AMPS

•See Electrical Data Sheet for details.

•Unit mounted NEMA 4X non fused disconnect switch c/w neutral kit.

•Unit mounted components with Nema 4X rating include the following:

Electrical control panel(s) Air Proving Switch

•Wiring to be color coded and numbered.

•Motor and sensor wiring c/w 316 stainless steel conduit, liquid tight flex and 316 stainless steel fittings.

•Exhaust air motor is 230V/3PH/60HZ. Motor three phase FLA is 1.8 amps.

1 DATE 26Feb2020 Continued on page 2

EngA MODEL: QTY: TAG:LM1/O/MV/GH1 1 OX1

FILTER SECTION DATA Face Loaded c/w Type 8 Holding Frame FILTER TYPE EngA Standard Pleated with MERV 13 rating QTY/SIZE 1 16 x 20 x 4" QTY/SIZE

TOTAL GROSS AREA 2.22 SQ.FT. FACE VELOCITY 135 FPM @ 300 CFM

•Filters may be shipped loose or mounted in the tracks •1 spare set of filters (filter metal frame not included) shipped loose •316 Stainless steel filter frame.

SHIPPED LOOSE ITEMS (See filter section for filters and spare filters) 1 Exhaust stack (Engineered Air) 1 Blast Gate Belled PVC 4.00 (United Equipment & fabricators 325040D) 6 Coorstek ADS96R Spare Corona Plates

2 DATE 26Feb2020 SUBMITTED BY SAM SEGO / TJB

1 2

R R

TAG:

DATE:

DRN.BY:

CHKD.BY:

DWG.NO:REVISION:

OX-1

MAR 28 2019

TJB05/14/2019 - ANL

JLC 08547M-01-1

LM SERIES

LM1/O/MV/GH1

DAT PANEL

1 2

41 2

1 8

1 4

61 2

AC

C

ES

S

AC

C

ES

S

AC

C

ES

S

AC

C

ES

S

S .S

. N

EM

A

X D

IS

C

O N

N

EC

T

" 3

S

.S

AI

R

M

IX

ER

N

EM

A 4X

A/ C

U N

IT

H 2S

O

TR

AN

SM

IT

TE

R S

LI

FT

IN

G

PA

D

S

O

H

2S

SA

M

PL

E

TU

BE

S

H 2S

S

AM

PL

E

TU

BE

S

R

* 1 "Ø

S .S

. D R

AI

N

C O

N N

EC

TI

O N

(T

YP

O F

3)

01 2

(8 ) M

O U

N

TI

N G

TA

BS

c /w

/4

" Ø

PR

E- D

R

IL

LE

D

H O

LE

S

Tag: OX-1

Fan information

Size/Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Class

Volumetric Flow Speed (RPM)

Max Speed

Power

SP

Outlet Vel805F/JRW SD

375 2555

4,550 RPM @ 70 °F

0.24

1.5(in WC)

(BHP)

(FPM)

(CFM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.075Density (lb/ft³)

Adjusted for Apply Compressibility

70855259677684898992Inlet dB Sound

Power Ea.

Octave Bands 1 2 3 4

LwA: The overall (single value) fan sound power level in dB re.

dBA: Estimated sound pressure level (re:0.0002 microbar) based on a single ducted installation at 5 ft., using a directivity factor of 1.

5 6 7 8 LwA dBA

-12

Watts, ‘A’ weighted.

Customer:

Job ID:

Job Name: PS072

DK8547

Date: November 13, 2018

All quotations per Twin City Fan Terms and Conditions found at www.twincityfan.com/TC_TCF.pdf

Ver 10.1 January 2017 - Created 11-13-2018 Updated 11-13-2018 Owner Timothy Bernhart TCF Self Registered

BROWN

WHITE

YELLOW

RED

BLUE

ORANGE

COLOR LEGEND

GREEN

SHIELD

BLACK

- BR (LINE 2)

- W (NEUTRAL)

- YL (LINE 3)

- RD (120V)

- BL (24V)

- OR (LINE 1)

- GR (GROUND)

- SH (RED/BLACK)

- BK

ELECTRICAL DATA

EngA MODEL: QTY: TAG:LM1/O/MV/GH1 1 OX1

Power Supply

Minimum Circuit Ampacity

Terminal Block to Accept

Maximum Fuse (Dual Element)

Maximum Breaker

120 / 1 / 60 32.0 AMPS 8 Awg 40 AMPS 40 AMPS

Components Model Minimum Conductor Size

Ampacity

FLA / LRA

DAT 210 14 Awg 12.8 AC Unit 14 Awg 6.6 Control Circuit 14 Awg .4 Main Control Xfmr 14 Awg .6 Fan Controller KBVF 14 Awg 8.3

UNIT CONTROL PANEL(S) SHORT CIRCUIT CURRENT RATING (SCCR)

Short circuit current 5 kA rms symmetrical, 120 V maximum

WIRING DRAWING LEGEND

APS Air Proving Switch ASF Auto Fan Switch AUX Auxiliary Contact BM Burner Motor C Contactor CCH Compressor Crankcase Heater CFC Condenser Fan Control CLC Compressor Loading Control CPM Compressor Protection Module CR Cooling Relay CS Current Sensor DHSS Draft Hood Spill Switch

DM Damper Motor FR Fan Relay GND Ground GV Gas Valve HL High Limit HPC High Pressure Control HR Heating Relay IGN Ignition Control ITP Internal Thermo Protection LPC Low Pressure Control M Motor MV Main Gas Valve

NFD Non Fused Disconnect OL Thermal Overload PS Pressure Sensor PV Pilot Gas Valve R Relay RevHL Reverse Airflow High Limit TB Terminal Block TDF Time Delay Fuse TDR Time Delay Relay TS Temperature Sensor VFD Variable Frequency Drive XFMR Transformer

UNIT FUNCTION

Exhaust air motor three phase FLA is 1.8 amps.

Unit disconnect switch 'on', service switch ‘on.

Unit on/off switch 'on' exhaust blower starts and runs continuously. Exhaust blower speed is controlled a variable speed control.

Unit on/off switch 'off', exhaust blower shutdown. Unit is off.

GH1 Generator Head Hand/Off/Auto switch in ‘Auto', generator head airflow switch 'closed', three minute purge timer activated. Purge timer contacts 'closed', inverter and corona transformer enabled. Oxidation level is modulated as required to neutralize foul air H2S by unit mounted controller and H2S sensor.

Hand/Off/Auto switch ‘Hand', operation as above, except oxidation level is controlled via manual oxidation potentiometer.

Hand/Off/Auto switch ‘Off', generator head shuts down.

Note 1 Refer to manuals shipped with unit for a more detailed explanation of maintenance, component(s) and/or controller(s).

Note 2 Go to www.engineeredair.com/manuals/manuals.asp for online manual details.

DATE: 26FEB2020 SUBMITTED BY: SAM SEGO / TJB

www.engineeredair.com/manuals/manuals.asp

Pump Station 16 Engineered Air

Model Numbers GH4 and LM3/O

DRAWING TRANSMITTAL SHEET

JOB NO. DK8526(OF314)

DATE August 09, 2019

ORLANDO HEAD OFFICE OTHER USA

SALES OFFICE & FACTORY SALES OFFICES

251 PLAZA DRIVE SUITE A

OVIEDO FL

32765

(407) 3598743

DESOTO KANSAS DESOTO, CLEVELAND, RICHMOND, DENVER, HOUSTON,

CINCINNATI, KANSAS, CHICAGO, COLUMBUS, DALLAS,

ST LOUIS, INDIANAPOLIS, OMAHA, PITTSBURGH, AUSTIN,

CHARLOTTE, SAN FRANCISCO, PORTLAND, WASHINGTON,

SAN DIEGO

CONTRACTOR TLC DIVERSIFIED, INC.

ADDRESS 2719 17TH St E

Palmetto FL 342219314

ENGINEER ARCADIS

JOB NAME PINELLAS COUNTY PS 016 OC

THIS ORDER IS SUBJECT TO APPROVAL. MANUFACTURING IS HELD PENDING RETURN OF ONE APPROVED COPY OF

THESE FORMS TO THE INDICATED OFFICE.

THIS ORDER IS NOT SUBJECT TO APPROVAL AND IS BEING MANUFACTURED ACCORDING TO THE ATTACHED FORMS.

COPIES ENCLOSED DESCRIPTION

1 EngA Submittal Revision Summary

4 EngA Submittal Record PS016 OC 4 EngA Mechanical Drawing 08526M011 4 EngA Mechanical Drawing 08526M012 4 EngA Lamicoid Detail Drawing 08526L011 4 EngA Generator Head Performance Data Sheet 08526M012 4 TwinCity Exhaust Air Fan Performance Curve and Sound Data PS016 OC 4 EngA Internal Wiring Diagram 08526E011 4 EngA Internal Wiring Diagram 08526E012 4 EngA Electrical Data Sheet PS016 OC 4 EngA Field Wiring Diagram 08526F011

4 EngA Installation, Operation and Maintenance Manual (LM Series) 4 TwinCity IM105 Piezometer Ring Installation, Operation & Maintenance Manual

PER CHRIS ZINDER / TJB

SUBMITTAL REVISIONS

JOB NAME: PINELLAS COUNTY PS 016 OC DK8526(OF314)JOB NO:

CUSTOMER: TLC DIVERSIFIED, INC.

ENGINEER: ARCADIS REVISION DATE: Aug 09, 2019

CHANGES AND/OR REVISIONS MADE TO THIS ORDER:

08/09/2019:

Rev…