IMH1.pdf.pdf
PDF 176 KB Posted
- Solicitation number
- AG-82HW-S-09-0019
About this file
IMH1
View the file
Other files
| File | Type | Posted |
|---|---|---|
| Abstract of Bids S-09-0019.pdf | ||
| Amendment 2.pdf | ||
| NSSL 0231.TIF | TIF image | |
| NSSL 0229.TIF | TIF image | |
| NSSL 0233.TIF | TIF image | |
| 2002 lighting plan revised areas.pdf | ||
| NSSL 0230.TIF | TIF image | |
| NSSL 0228.TIF | TIF image | |
| Ballast selection list20090819.pdf | ||
| NSSL 0227.TIF | TIF image | |
| Amendment 1 in PDF.pdf | ||
| Pre-bid walk through attendance list Ft Collins Lighting.pdf | ||
| Lighting Spreadsheet 20090818 revision 4WCP.XLSX | XLSX spreadsheet | |
| NSSL 0234.TIF | TIF image | |
| NSSL 0232.TIF | TIF image | |
| Lithonia 20 20C fixtrures.pdf.pdf | ||
| WAL-14 spec.pdf.pdf | ||
| M-2x4.pdf.pdf | ||
| Wage Determination Ft Collins CO.pdf | ||
| Buy American excepted material or components.pdf | ||
| Lithonia 20C 20fixtures 2020090721 1 .pdf | ||
| IMH175C 2020090721 1 .pdf | ||
| Copy of Lighting Spreadsheet 20090720 revision 2GMG.pdf | ||
| AG-82HW-S-09-0019 - Replace Light Fixtures- Ft Collins - construction over 100K.DOC | DOC document | |
| WAL-14_specDL 2020090721 1 .pdf | ||
| M-2x4 2020090721 1 .pdf |
Show all 26
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
e-Vision Electronic Ballast for Metal Halide Lamps
Catalog Number IMH-175-C For (1) 150W ANSI M102, M142 or (1) 175W ANSI M137, M152 Metal Halide Lamp 120-277V 50/60Hz Electronic Status: Released
DIMENSIONS AND DATA
Lamp Data
Number Watts Input Volts
Catalog Number*
Line Current (Amps)
Input Power
(W)
Ballast Factor
Max
THD
Min Power Factor
Wiring Dia Figure Weight
(lb)
Max Distance to Lamp
(ft)
150 Watt Lamp, ANSI Code M102 or M142 (or 150W HPS Lamp ANSI S56) Minimum Starting Temp -30°C/-20°F 120 1.4 169
1 150
IMH-175-C-xxx
0.6 166
1.0 15 0.9 1 C 2.5 5
175 Watt Lamp, ANSI Code M137 or M152 Minimum Starting Temp -30°C/-20°F
120 1.7 194 1 175
IMH-175-C-xxx
0.7 191
1.0 15 0.9 2 C 2.5 5
INSTALLATION & APPLICATION NOT
1. Maximum allowable cas for measurement locatio
2. Ignition pulse is 4 kV ma
3. All leads are 12 inches lo
4. Ballast output will shutdo
5. Power must be cycled o
Data is based on tests performed by Advance transfo Specifications are subject to change without notice.
Advance • 10275 West Higg
Wiring Diagram 1
Figure C
CASE LENGTH = 7.3” [184]
MOUNTING LENGTH = 7.7” [195]
MOUNTING WIDTH = 2.9” [73]
OVERALL LENGTH = 8.02” [204]
CASE WIDTH = 3.6” [91]
HEIGHT = 1.5” [38]
Case Temperature Me
*Ordering Information Order Suffix Description
-LF Ballast with side exit leads and mounting feet
ES:
e temperature is 85°C. See figure above n x ng wn after 20 minutes if lamp fails to ignite ff – then on, after replacing lamp -BLS Ballast with bottom exit leads and mounting studs rmer in a controlled environment and representative of relative performance. Actual performance can vary depending on operating conditions.
All specifications are nominal unless otherwise noted.
ins Road • Rosemont, Illinois 60018-5603 • (847) 390-5000 • fax: 847-390-5109 • www.advancetransformer.com
A DIVISION OF PHILIPS ELECTRONICS NORTH AMERICA CORPORATION
Wiring Diagram 2 asurement Location
MEASURE CASE
TEMPERATURE ON
RIGHT HEAT SINK
CLIP AT BALAST
END
8/30/05
| Ballast for Metal Halide Lamps |
| Catalog Number IMH-175-C |
| For (1) 150W ANSI M102, M142 or (1) 175W ANSI M137, M152 Metal Halide Lamp |
| DIMENSIONS AND DATA |
| Catalog Number* |
| Line Current (Amps) |
| Input Power (W) |
| Ballast Factor |
| Max THD (%) |
| Min Power Factor |
| Wiring Dia |
| Figure |
| Weight (lb) |
| Max Distance to Lamp (ft) |
| 150 Watt Lamp, ANSI Code M102 or M142 \(or 150W |
| IMH-175-C-xxx |
| 1.4 |
| 169 |
| 1.0 |
| 15 |
| 0.9 |
| 1 |
| C |
| 2.5 |
| 5 |
| 0.6 |
| 166 |
| 175 Watt Lamp, ANSI Code M137 or M152 Minimum |
| IMH-175-C-xxx |
| 1.7 |
| 194 |
| 1.0 |
| 15 |
| 0.9 |
| 2 |
| C |
| 2.5 |
| 5 |
| 0.7 |
| 191 |
| INSTALLATION & APPLICATION NOTES: |
*Ordering Information
| Order Suffix |
| Description |
| -LF |
| Ballast with side exit leads and mounting feet |
| -BLS |
| Ballast with bottom exit leads and mounting studs |
| Data is based on tests performed by Advance transformer in a controlled environment and representative of relative performance. Actual performance can vary depending on operating conditions. Specifications are subject to change without notice. All spe |
File details come from the government source that posted it. Updated .