Addendum Two.pdf

COMMONWEALTH OF KENTUCKY

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

INVITATION TO BID NO: RFB-156-24

FOR: Cottages 111, 112 & 117 Renvoations Phase II Oakwood Intermediate Care Facility Cabinet for Health and Family Services Pulaski County, Kentucky

DATE: February 10, 2024

ADDENDUM NO. Two (2)

BIDDER SHALL CONFORM TO THE FOLLOWING CHANGES AS SAME SHALL BECOME BINDING

UPON THE CONTRACT TO BE ISSUED IN RESPONSE TO THIS INVITATION TO BID.

Item 1: Refer to addendum to be distributed by Lynn Imaging for all additions, deletions, and/or changes to specifications and/or drawings.

END OF ADDENDUM

Invitation to Bid No. RFB-156-24 For: Cottages 111, 112 & 117 Renvoations Phase II Oakwood Intermediate Care Facility Cabinet for Health and Family Services Pulaski County, Kentucky

Susan Ward, Statewide Procurement Analyst II Division of Engineering and Contract Administration

Account No. 729-C9SE-OW40-00

Oakwood Cottages 111, 112 & 117 Renovation

Cabinet for Health & Family Services

Somerset, KY

AI Project #2046

Addendum #2

The project contract documents are hereby amended as follows:

GENERAL

1. Select construction photos taken inside cottages 103 & 108 during the demolition of the phase one cottage renovation project have been included on the pages that following, for your reference only.

The scope in phase one cottages did not include the installation of any new ductwork below slab.

ARCHITECTURAL

DRAWINGS

Floor plan sheets D11-01- and D17-01

2. Refer to the attached drawing sheets revised for clarification purposes.

ADDENDUM

Page 1 of 3 Find a way.

Date: February 9, 2024

Project: Oakwood Cottages 111, 112 & 117 Renovations Phase II

KFI Project Number: 22-0366.00

Addendum Number: 2

THIS ADDENDUM IS A CONTRACT DOCUMENT AND MAY APPLY TO ANY OR ALL CONTRACTS AND SUBCONTRACTS UNLESS OTHERWISE SPECIFIED HEREIN

OR SHOWN ON THE ATTACHED DRAWINGS (IF ANY). ALL WORK REQUIRED BY THIS ADDENDUM SHALL BE IN COMPLETE ACCORD WITH THE CONTRACT

DOCUMENTS AND SUBSEQUENT ADDENDA THERETO. THE ITEMS LISTED IN THIS ADDENDUM ARE NOT IN ANY ORDER IN REGARD TO THE DRAWINGS

OR THE SPECIFICATIONS. ALL CONTRACTORS ARE CAUTIONED TO EXAMINE EACH AND EVERY ITEM OF THIS ADDENDUM.

THE FOLLOWING CHANGES OR CLARIFICATIONS TO THE PLANS & SPECIFICATIONS SHALL BE INCLUDED AS PART OF THE CONTRACT DOCUMENT

SPECIFICATION CHANGES:

Section Number:

1. Refer to Section 232113. Delete paragraph 3.7-E. There is no external water piping on this project and glycol is not required.

2. Refer to Section 271513. There is no cable tray in this project. Remove all references to cable trays. All cables shall be installed in conduit.

DRAWING CHANGES:

1. Refer to drawing nos. H11-10R3, H17-10R3, and H17-20R3 for revisions.

CONTRACTOR QUESTIONS:

1. VAV-14 & -16 are in schedule but missing in floor plans. Please clarify.

a. Not all units shown on schedule may be on floor plans.

2. VAVs found on floor plan have multiple quantities with the same tag. Please clarify.

a. Same sizes of mechanical equipment may use same tags and quantity will be based on drawing takeoff.

3. There are VAVs shown on floor plans with missing tags. Please clarify.

a. See revision drawings included in this addendum.

4. RH-3, RH-5, RH-7, RH-9, RH-10, RH-11 and RH-12 is mentioned in schedule but missing in floor plan.

Please clarify.

a. Not all units shown on schedule may be on floor plans.

5. Reheat Coil found on floor plan have multiple quantity with the same tag. Please clarify.

Page 2 of 3 Find a way.

a. Same sizes of mechanical equipment may use same tags and quantity will be based on drawing takeoff.

6. Please confirm that Cottages 111 & 112 have the exact same mechanical equipment.

a. Cottages 111 & 112 have identical layouts.

7. Can BIM Modeling spec be provided so all MEP trades know BIM requirements desired for this project?

Such as software needed (Revit) and clash detection (Navisworks). And what trades are specifically involved. Who will be the lead on the BIM and run the clash detection, etc.

a. See specifications and addendum #1 for coordination requirements. General and mechanical contractors will take lead and all necessary contractors will be involved in coordination and clash detection.

8. Can existing below slab sanitary piping be abandoned in place except where new below slab sanitary piping may interfere?

a. It will be acceptable to abandon below slab piping shown to be demolished, where it does not interfere or abut with installation of any new work. Open ends shall be sealed with concrete.

9. Will the under slab ductwork have to be PVC Coated? Or any special requirements?

a. See specification section 233113 – METAL DUCTS.

10. Provide detail of under slab duct chase construction. Poured in slab? Build chase? Please clarify method and underground duct material desired.

a. See specification section referenced above for underslab duct specification. Duct will be buried under building slab.

11. Does the new AHU in basement get new concrete pad?

a. If locations are acceptable existing concrete pads can be reused. Pads will be cut back or added to as required for new equipment sizes.

12. Demo plan sheet (D11-01) only depicts a small amount of concrete floor slab removal. This is somewhat misleading. There will be an extensive amount of concrete floor slab removal for our underground plumbing and underground ductwork. The plumbing and HVAC plans do not mention anything about saw cutting, floor removal, etc. for our new work going in. At pre-bid it was mentioned by design team approximately 60% of flooring would be removed. Please clarify.

a. See Addendum #1. Contractors shall coordinate for additional demolition where required for installation of work.

13. Can Camus Hydronic be listed as an Equal under section 235339?

a. Equipment will not be preapproved. Refer to Section 235239, paragraph 2.2-A. Specification is

“open” to equipment meeting specifications.

14. Boiler flow diagram shows controls valves for the variable primary. Is the boiler manufacturer to supply or the controls contractor?

Page 3 of 3 Find a way.

a. Valve may be supplied and controlled by either boiler or controls contractors, but must be visible to users thru DDC.

15. Specification for BAS conduit installation requirements refer to section 260533 and 270528, both sections that do not exist in the spec-book. Please state the requirement for conduit for BAS wiring.

a. 260533 is Raceways and Boxes for Electrical Systems. This section is applicable to all raceways required for all cabling on the project. The specified raceways are EMT and GRC.

16. What are the sizes of the listed existing equipment below

a. EX panel 2A-C being demolished: 120/208V, 400A Square D QMB Distribution Panelboard with Fused Switches.

b. Ex Emergency panel being demolished: 120/208V, 12 pole, 100 amp panel

c. Ex Transfer Switch: 120/208V, Zenith 75 amps, Type MT7E

d. Ex Generator: 120/208V, 15KW

17. Due to NEC Code we cannot install junction boxes above a inaccessible ceiling, The specs call for EMT to be ran on branch circuits. This will cause issues and there will need to be access panels installed pretty frequently. Just want to clarify that is the direction we are going.

a. Access Doors are specified in Section 083150. The intent is that close coordination will need to be done with all trades to minimize the quantity of access panels required. Locate junction and pull boxes near other equipment above ceiling that will need to be accessible.

18. For all systems there will be conduit rough in to above accessible ceiling, are we to run conduit for each device as pathway or are J-hook pathways ran in a central location okay for system raceways ?

a. All system cabling shall be ran in conduits. Multiple cables may be combined into larger conduits.

END OF ADDENDUM

D11-03

A

B

C

8 9

A.

B.

C.

D11-03

D11-03

D11-03 2

D-1

P-1

P-3P-3P-3

P-3

P-2

P-2

D-1D-1

P-3

P-3

D-1

D11-03

D11-03

Sim

D-10

5' - 4"±

5' - 4"±

9' - 8"±

2' - 10

2' - 10"±

D-6

D-7

D-7

D-10

D-1D-1

D-1D-1

D-2D-2

D-6

D11-03

D-11

D-10

D-11

D-11

P-2P-2P-2

D-11

EXT-11

D-1

D-12

D-13

D-13

D-12

TYP.

D-12

D-15

D-15

D-15

D-0

D-1D-1

D-1D-1D-1

D-1

D-1

D-0

D-9 D-9

D-3

D-9

D-3

P-3

D-12

D-12D-12

P-1

P-1

P-3

P-1

P-1

D-4

D-4

D-7 D-7

D-7

D-7

EXISTING BELOW SLAB CHASE NOTE:

HORIZONTAL CHASES OF CMU AND CONCRETE CONSTRUCTION WITH DUCTWORK EXIST

BELOW SLAB. PLEASE REFER TO MECHANICAL DRAWINGS FOR LAYOUT OF NEW BELOW

SLAB RETURN AIR DUCTWORK / HORIZONTAL DUCT CHASES REQUIRED. EXISTING CHASES

MAY BE REUSED WHERE IT IS PRACTICAL. CONTRACTOR SHALL BE RESPONSIBLE TO

CLOSE THE ENDS OF ANY AND ALL EXISTING ABANDONED CHASES (WHERE EXPOSED BY

SLAB TRENCHING FOR UTITILIES, ETC.) WITH MASONRY, TO CONTROL THE SPREAD OF

NEW DGA TO BE INSTALLED BELOW AREAS OF NEW SLAB. SLAB PATCHING WILL BE

REQUIRED AT SELECT EXISTING DUCT OPENINGS, SUCH AS AT BEDROOM WALLS.

SALVAGE ITEMS NOTE:

REFER TO DEMOLITION SECTION IN THE PROJECT SPECIFICATIONS FOR A LIST OF MAJOR

ITEMS TO BE SALVAGED. CONTRACTOR SHALL COORDINATE SALVAGE WITH OWNER / END

USER TO DETERMINE FINAL SALVAGE LIST AND STORAGE LOCATION OF THOSE ITEMS.

SLAB DEMO NOTE:

DEMOLITION OF ADDITIONAL SLAB AREAS WILL BE NECESSARY, AS REQUIRED FOR THE

INSTALLATION OF NEW SANITARY WASTE PIPING AND RETURN AIR DUCTWORK. REFER TO

PLUMBING AND HVAC DRAWINGS.

D-6 D-6

D-6

D-6

DRAWING NO.

ACCOUNT

NO.

729-C9SE-OW40-00

COMMONWEALTH OF KENTUCKY

FINANCE AND ADMINISTRATION CABINET

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

DIVISION OF ENGINEERING AND CONTRACT

ADMINISTRATION

FRANKFORT, KENTUCKY

DECA REVIEWED

DECA LOG #

2023.09.20RTA DATE

A&E FILE NO.

DKCHECKED BY

DRAWN BY

DRAWING DATE

DRAWING INFORMATION

PHASE C - RTA

DATEDESCRIPTION OF REVISIONS

REVISION HISTORY OF THIS DRAWING

DATEDESCRIPTION OF REVISIONS

MDF

OAKWOOD - RENOVATION OF COTTAGES 111, 112, & 117

2441 US HIGHWAY 27, SOMERSET - PULASKI COUNTY, KY

Architectural Investments

222 SOUTH FIRST STREET - SUITE 206

LOUISVILLE, KENTUCKY 40202-1367

PHONE: 502-562-9220 FAX: 502-589-1571

[P lo tS ta m p E v a l]

-M A

Y -2 architectural investments

DEMOLITION FLOOR PLAN - COTTAGES 111 & 112

D11-01

DESIGN INTENT

2023.09.20

1/8" = 1'-0"

GROUND FLOOR - DEMOLITION

KEYNOTES

D-0 GENERAL INTERIOR DEMOLITION OF ALL OF INTERIOR CONSTRUCTION COMPLETE - EXTERIOR WALLS, WINDOWS, DOORS, STRUCTURAL ITEMS ONLY TO REMAIN UNO, CONTRACTOR TO PROVIDE AN EMPTY

SHELL FOR TOTAL NEW CONSTRUCTION.

D-1 REMOVE EXISTING INTERIOR WALLS & DOORS (SHOWN DASHED) THROUGHOUT AREA OF WORK, INCLUDING, BUT NOT LIMITED TO, DOORS, FRAMES, WINDOWS AND PLASTER / GYPSUM BOARD, METAL FRAME WALL CONSTRUCTION, CERAMIC TILE, WOOD TRIM AND TRANSOMS. REMOVE ALL ELECTRIC / LOW VOLTAGE / DATA OUTLETS, WIRING AND CONDUIT. THE AREA OF WORK INCLUDES THE ENTIRE INTERIOR OF COTTAGE. NOTES: A. SALVAGE DOOR HARDWARE FOR RE-USE - REFER TO SELECTIVE DEMOILITION SPECIFICATIONS FOR COMPLETE LIST AND ADDITIONAL INFORMATION. B. PROTECT ALL

EXISTING ADJACENT CONSTRUCTION TO REMAIN FROM DAMAGE.

D-2 SAW-CUT AND REMOVE PORTION OF EXISTING CONCRETE SLAB AS REQUIRED FOR NEW WORK, REINFORCE AT PERIMETER OF NEW OPENING PER STRUCTURAL; INSPECT SLAB FOR CONDUIT PRIOR TO DEMOLITION AND NOTIFY A/E TEAM IMMEDIATELY IF ITEMS OF CONCERN ARE IDENTIFIED.

PROTECT BALANCE OF EXISTING SLAB (TO REMAIN) FROM DAMAGE, THROUGHOUT AREA OF WORK.

D-3 REMOVE ALL EXISTING FLOOR, WALL & CEILING FINISHES THROUGHOUT, INCLUDING, BUT NOT LIMITED TO: FLOOR TILE, CARPET, VWC ETC. PROTECT ANY EXISTING SUBSTRATES THAT ARE TO REMAIN, PATCH AND PREPARE SURFACES TO RECEIVE NEW FINISHES.

D-4 REMOVE EXISTING PLUMBING FIXTURES THROUGHOUT, TEMPORARILY CAP OFF EXISTING PIPING

BELOW SLAB AS NEEDED. REFER TO PLUMBING DRAWINGS.

D-6 REPLACE / REWORK EXISTING CONCRETE SLAB PORTION AS REQUIRED TO PROVIDE 1/8" PER 1'-0"

SLOPE MINIMUM TO FLOOR DRAIN IN NEW WORK - REFER TO PLUMBING.

D-7 SAW-CUT / REPLACE EXISTING CONCRETE SLAB PORTION AS REQUIRED TO RECEIVE NEW ADA

ACCESSIBLE ROLL-IN SHOWER FLOOR PAN - REFER TO PLUMBING.

D-9 REMOVE EXISTING CASEWORK, COUNTERTOP, BASE AND WALL CABINETS THROUGHOUT.

D-10 REMOVE EXISTING EXTERIOR HM DOOR & FRAME (SHOWN DASHED), PROTECT ANY ADJACENT SURFACES TO REMAIN FROM DAMAGE. REFER TO ELEVATIONS. SALVAGE, RETAIN AND STORE PER

OWNER DIRECTION.

D-11 REMOVE PORTION OF EXISTING EXTERIOR MASONRY / METAL FRAMING AND PLASTER WALL CONSTRUCTION (SHOWN DASHED), AS REQUIRED FOR NEW LAYOUT. SALVAGE AS MUCH BRICK AS

POSSIBLE FOR RE-USE IN INFILL. PROTECT ADJACENT SURFACES FROM DAMAGE. REFER TO

ELEVATIONS.

D-12 REMOVE EXISTING EXTERIOR STEEL WINDOW SHOWN DASHED, TYPICAL THROUGHOUT (EXCEPT

CLERESTORY IS TO REMAIN). PROTECT ADJACENT SURFACES FROM DAMAGE. REFER TO

ELEVATIONS.

D-13 EXISTING EXTERIOR STEEL CLERESTORY WINDOW SYSTEM ABOVE TO REMAIN, PROTECT FROM

DAMAGE, TYPICAL. REMOVE BLINDS, CLEAN AND PREPARE STEEL FRAMES TO RECEIVE PAINT.

D-15 REMOVE EXISTING EXISTING PLASTER / GWB AND BATT INSULATION FROM EXISTING METAL FRAME

EXTERIOR WALLS (GABLE ENDS & SERVICE ENTRANCE), PROTECT WALL CONSTRUCTION FROM

DAMAGE.

EXT-11 EXISTING WALL HYDRANT FIRE SERVICE CONNECTION TO REMAIN - PRTOECT FROM DAMAGE.

P-1 PROTECT ALL EXISTING EXTERIOR BUILDING CONSTRUCTION FROM DAMAGE, WHICH IS TO REMAIN, EXCEPT WHERE NOTED OTHERWISE. THIS INCLUDES (BUT IS NOT LIMITED TO) ROOFING, GUTTERS, WOOD EAVES AND MASONRY WALL CONSTRUCTION.

P-2 PROTECT ALL EXISTING EXTERIOR WALL CONSTRUCTION FROM DAMAGE, WHICH IS TO REMAIN, EXCEPT WHERE NOTED OTHERWISE. THIS INCLUDES (BUT IS NOT LIMITED TO) MASONRY, STEEL

FRAMING AND STEEL CLERESTORY WINDOW SYSTEM.

P-3 PROTECT ALL EXISTING STEEL STRUCTURE, STRUCTURAL CONCRETE, AND WOOD ROOF DECKING FROM DAMAGE, TYPICAL THROUGHOUT. CLEAN, SAND AND PAINT INTERIOR STEEL TO BE EXPOSED, AS

PER SCHEDULE.

SCOPE NOTE:

EXISTING DEMO, AND NEW CONFIGURATIONS OF

COTTAGES 111 & 112 ARE VIRTUALLY IDENTICAL.

ALL WORK SCOPE ON SHEETS NUMBERED 'A11- '

APPLIES EQUALLY TO BOTH COTTAGES 111 & 112.

FOR SIMPLICITY, ALL ROOM AND DOOR TAGS ARE

SHOWN STARTING WITH '11,' INDICATING

COTTAGE 111. ROOMS IN COTTAGE 112 MAY BE

IDENTIFIED USING '12' AS THE FIRST TWO DIGITS.

HAZARDOUS MATERIALS NOTE:

AN ENVIRONMENTAL SURVEY OF THE COTTAGES WAS COMPLETED IN AUG. 2020.

NO HAZARDOUS MATERIALS OF CONCERN WERE IDENTIFIED, WITH EXCEPTION OF

THE FIRE DOORS. CORES OF SUCH FIRE DOORS MUST NOT BE DISTURBED DURING

REMOVAL AND SHALL BE PROPERLY DISPOSED. A COPY OF THIS REPORT MAY BE

OBTAINED FROM THE ARCHITECT UPON REQUEST, FOR INFORMATION ONLY.

Addendum #2 2/8/24

A

B

C

D17-03

12 11

A.

B.

C.

A17-05

D17-03

D17-03

D-10

D-11D-11D-11

D-1D-1D-1

D-1D-1

D-1D-1

P-2

D-1D-1D-1P-2P-2

D-12 D-11

D-0

D-3

D-0

D-3

P-2

P-1

P-1

D-6

D-7

D-6

D-7

D-6

D-2

D-2

D-14

D-15

P-2

D-10

D-10

EXT-11

d

12' - 6" ±

D-6

D-4

D-4

D-4

D-13

D-13

D-12

D-12

D-15

D-15

D-15

D-9

D-9

D-1

D-1

D-7

D-7

D-6

D-6

EXISTING BELOW SLAB CHASE NOTE:

HORIZONTAL CHASES OF CMU AND CONCRETE CONSTRUCTION WITH DUCTWORK EXIST

BELOW SLAB. PLEASE REFER TO MECHANICAL DRAWINGS FOR LAYOUT OF NEW BELOW

SLAB RETURN AIR DUCTWORK / HORIZONTAL DUCT CHASES REQUIRED. EXISTING CHASES

MAY BE REUSED WHERE IT IS PRACTICAL. CONTRACTOR SHALL BE RESPONSIBLE TO

CLOSE THE ENDS OF ANY AND ALL EXISTING ABANDONED CHASES (WHERE EXPOSED BY

SLAB TRENCHING FOR UTITILIES, ETC.) WITH MASONRY, TO CONTROL THE SPREAD OF

NEW DGA TO BE INSTALLED BELOW AREAS OF NEW SLAB. SLAB PATCHING WILL BE

REQUIRED AT SELECT EXISTING DUCT OPENINGS, SUCH AS AT BEDROOM WALLS.

SALVAGE ITEMS NOTE:

REFER TO DEMOLITION SECTION IN THE PROJECT SPECIFICATIONS FOR A LIST OF MAJOR

ITEMS TO BE SALVAGED. CONTRACTOR SHALL COORDINATE SALVAGE WITH OWNER / END

USER TO DETERMINE FINAL SALVAGE LIST AND STORAGE LOCATION OF THOSE ITEMS.

SLAB DEMO NOTE:

DEMOLITION OF ADDITIONAL SLAB AREAS WILL BE NECESSARY, AS REQUIRED FOR THE

INSTALLATION OF NEW SANITARY WASTE PIPING AND RETURN AIR DUCTWORK. REFER TO

PLUMBING AND HVAC DRAWINGS.

DRAWING NO.

ACCOUNT

NO.

729-C9SE-OW40-00

COMMONWEALTH OF KENTUCKY

FINANCE AND ADMINISTRATION CABINET

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

DIVISION OF ENGINEERING AND CONTRACT

ADMINISTRATION

FRANKFORT, KENTUCKY

DECA REVIEWED

DECA LOG #

2022.x.xRTA DATE

A&E FILE NO.

KBCHECKED BY

DRAWN BY

DRAWING DATE

DRAWING INFORMATION

PHASE C - RTA

DATEDESCRIPTION OF REVISIONS

REVISION HISTORY OF THIS DRAWING

DATEDESCRIPTION OF REVISIONS

MDF

OAKWOOD - RENOVATION OF COTTAGES 111, 112, & 117

2441 US HIGHWAY 27, SOMERSET - PULASKI COUNTY, KY

Architectural Investments

222 SOUTH FIRST STREET - SUITE 206

LOUISVILLE, KENTUCKY 40202-1367

PHONE: 502-562-9220 FAX: 502-589-1571

[P lo tS ta m p E v a l]

-M A

Y -2 architectural investments

DEMOLITION FLOOR PLAN - COTTAGE 117

D17-01

DESIGN INTENT

2023.06.30

1/8" = 1'-0"

GROUND FLOOR - DEMOLITION

KEYNOTES

D-0 GENERAL INTERIOR DEMOLITION OF ALL OF INTERIOR CONSTRUCTION COMPLETE - EXTERIOR WALLS, WINDOWS, DOORS, STRUCTURAL ITEMS ONLY TO REMAIN UNO, CONTRACTOR TO PROVIDE AN EMPTY SHELL

FOR TOTAL NEW CONSTRUCTION.

D-1 REMOVE EXISTING INTERIOR WALLS & DOORS (SHOWN DASHED) THROUGHOUT AREA OF WORK, INCLUDING, BUT NOT LIMITED TO, DOORS, FRAMES, WINDOWS AND PLASTER / GYPSUM BOARD, METAL FRAME WALL CONSTRUCTION, CERAMIC TILE, WOOD TRIM AND TRANSOMS. REMOVE ALL ELECTRIC / LOW VOLTAGE / DATA OUTLETS, WIRING AND CONDUIT. THE AREA OF WORK INCLUDES THE ENTIRE INTERIOR OF COTTAGE. NOTES:

A. SALVAGE DOOR HARDWARE FOR RE-USE - REFER TO SELECTIVE DEMOILITION SPECIFICATIONS FOR COMPLETE LIST AND ADDITIONAL INFORMATION. B. PROTECT ALL EXISTING ADJACENT CONSTRUCTION TO

REMAIN FROM DAMAGE.

D-2 SAW-CUT AND REMOVE PORTION OF EXISTING CONCRETE SLAB AS REQUIRED FOR NEW WORK, REINFORCE AT PERIMETER OF NEW OPENING PER STRUCTURAL; INSPECT SLAB FOR CONDUIT PRIOR TO DEMOLITION AND NOTIFY A/E TEAM IMMEDIATELY IF ITEMS OF CONCERN ARE IDENTIFIED. PROTECT BALANCE OF EXISTING SLAB

(TO REMAIN) FROM DAMAGE, THROUGHOUT AREA OF WORK.

D-3 REMOVE ALL EXISTING FLOOR, WALL & CEILING FINISHES THROUGHOUT, INCLUDING, BUT NOT LIMITED TO:

FLOOR TILE, CARPET, VWC ETC. PROTECT ANY EXISTING SUBSTRATES THAT ARE TO REMAIN, PATCH AND

PREPARE SURFACES TO RECEIVE NEW FINISHES.

D-4 REMOVE EXISTING PLUMBING FIXTURES THROUGHOUT, TEMPORARILY CAP OFF EXISTING PIPING BELOW SLAB

AS NEEDED. REFER TO PLUMBING DRAWINGS.

D-6 REPLACE / REWORK EXISTING CONCRETE SLAB PORTION AS REQUIRED TO PROVIDE 1/8" PER 1'-0" SLOPE

MINIMUM TO FLOOR DRAIN IN NEW WORK - REFER TO PLUMBING.

D-7 SAW-CUT / REPLACE EXISTING CONCRETE SLAB PORTION AS REQUIRED TO RECEIVE NEW ADA ACCESSIBLE

ROLL-IN SHOWER FLOOR PAN - REFER TO PLUMBING.

D-9 REMOVE EXISTING CASEWORK, COUNTERTOP, BASE AND WALL CABINETS THROUGHOUT.

D-10 REMOVE EXISTING EXTERIOR HM DOOR & FRAME (SHOWN DASHED), PROTECT ANY ADJACENT SURFACES TO REMAIN FROM DAMAGE. REFER TO ELEVATIONS. SALVAGE, RETAIN AND STORE PER OWNER DIRECTION.

D-11 REMOVE PORTION OF EXISTING EXTERIOR MASONRY / METAL FRAMING AND PLASTER WALL CONSTRUCTION (SHOWN DASHED), AS REQUIRED FOR NEW LAYOUT. SALVAGE AS MUCH BRICK AS POSSIBLE FOR RE-USE IN

INFILL. PROTECT ADJACENT SURFACES FROM DAMAGE. REFER TO ELEVATIONS.

D-12 REMOVE EXISTING EXTERIOR STEEL WINDOW SHOWN DASHED, TYPICAL THROUGHOUT (EXCEPT CLERESTORY

IS TO REMAIN). PROTECT ADJACENT SURFACES FROM DAMAGE. REFER TO ELEVATIONS.

D-13 EXISTING EXTERIOR STEEL CLERESTORY WINDOW SYSTEM ABOVE TO REMAIN, PROTECT FROM DAMAGE, TYPICAL. REMOVE BLINDS, CLEAN AND PREPARE STEEL FRAMES TO RECEIVE PAINT.

D-14 REMOVE EXISTING SPIRAL STAIR, PATCH AS REQUIRED AT ANCHORING LOCATIONS. PROTECT ALL ADJACENT

SURFACES FROM DAMAGE.

D-15 REMOVE EXISTING EXISTING PLASTER / GWB AND BATT INSULATION FROM EXISTING METAL FRAME EXTERIOR

WALLS (GABLE ENDS & SERVICE ENTRANCE), PROTECT WALL CONSTRUCTION FROM DAMAGE.

EXT-11 EXISTING WALL HYDRANT FIRE SERVICE CONNECTION TO REMAIN - PRTOECT FROM DAMAGE.

P-1 PROTECT ALL EXISTING EXTERIOR BUILDING CONSTRUCTION FROM DAMAGE, WHICH IS TO REMAIN, EXCEPT WHERE NOTED OTHERWISE. THIS INCLUDES (BUT IS NOT LIMITED TO) ROOFING, GUTTERS, WOOD EAVES AND

MASONRY WALL CONSTRUCTION.

P-2 PROTECT ALL EXISTING EXTERIOR WALL CONSTRUCTION FROM DAMAGE, WHICH IS TO REMAIN, EXCEPT WHERE NOTED OTHERWISE. THIS INCLUDES (BUT IS NOT LIMITED TO) MASONRY, STEEL FRAMING AND STEEL

CLERESTORY WINDOW SYSTEM.

HAZARDOUS MATERIALS NOTE:

AN ENVIRONMENTAL SURVEY OF THE COTTAGES WAS COMPLETED IN AUG. 2020.

NO HAZARDOUS MATERIALS OF CONCERN WERE IDENTIFIED, WITH EXCEPTION OF

THE FIRE DOORS. CORES OF SUCH FIRE DOORS MUST NOT BE DISTURBED DURING

REMOVAL AND SHALL BE PROPERLY DISPOSED. A COPY OF THIS REPORT MAY BE

OBTAINED FROM THE ARCHITECT UPON REQUEST, FOR INFORMATION ONLY.

Addendum #2 2/9/24

REF.

D

T

T

T

T

T

T

T

T

MAIN SUPPLY AND RETURN AIR

DUCT UP FROM FLOOR BELOW

TO ABOVE THIS FLOOR CEILING.

A

1 2 3 5 6 74

A.

B.

C.

1107 1105 1104 1102 1114A

1114B

1109 1111 1100

1118S

1118C

EF-1

EF-1

EF-1

EF-1

EF-1

EF-1

EF-1

EF-1

EF-1

EF-1

EF-1

30"x10" SA24"x10" SA

12"x12" SA

20"x12" PA 48"x12" PA

"ø

E A

1106 1103

1117A

IU-1

VAV-12

418-139616"x10" SA

6"ø EA

"ø E

A

VAV-8

200-624

S-12

312 CFM

"ø

E A

L-1

S-8

600 CFM

6"ø E

A

6"ø E

A

L-1

6"ø EA6"ø E

A

8"ø E

A

10"ø E

A

10"ø E

A

14"x12" S A

18"x14" S A

S-12

365 CFM

VAV-10

219-730

VAV-12

418-1436

S-4

200 CFM

S-4

200 CFM

S-4

200 CFM

10"x10" S A

8"x8" S A

12"x12" S A

S-8

724 CFM

27"x1 5" S

A

VAV-12

397-1324

S-13

719 CFM

VAV-10

216-719

VAV-5

120-240

S-1

60 CFM

S-8

715 CFM

S-12

312 CFM

S-8

650 CFM

S-8

650 CFM

S-1

60 CFM

S-1

60 CFM

VAV-12

675-1600

S-12

350 CFM

VAV-6

90-350

S-1

60 CFM

16"x10" SA

18"x16" SA

VAV-8

225-650

VAV-12

550-1455

DEMOLITION NOTE:

REMOVE ALL HVAC ITEMS (EQUIPMENT, PIPING, DUCTWORK, ETC.) IN IT'S ENTIRETY. SEE SPECIFICATIONS FOR LIST OF

EQUIPMENT TO BE TURNED OVER TO OWNER.

UNDERSLAB DUCTWORK AND PIPING MAY BE ABANDONED WHERE IT DOES NOT INTERFERE WITH INSTALLATION OF

NEW WORK.

WHERE DUCTWORK, AND PIPING ARE ABANDONED, ENDS SHALL BE REMOVED TO BELOW SLAB, PLUGGED WITH

CONCRETE, AND SLAB REPARED AS REQUIRED FOR NEW CONSTRUCTION.

2 2 2 2 2 2

2 2

27"x15" SA

14"x12" S A

VAV-6

150-359

VAV-5

120-349

VAV-5

120-349

5"ø PA

5"ø PA

6"ø EA

R-7

305 CFM

R-7

305 CFM

5"ø PA

5"ø PA

5"ø P

A

5"ø P

A

R-7

305 CFM

R-7

305 CFM

R-7

305 CFM

R-7

305 CFM

R-7

305 CFM

R-7

305 CFM

R-7

305 CFM

R-7

305 CFM

R-7

305 CFM

R-7

305 CFM

R-7

305 CFM

R-7

305 CFM

R-6

2000 CFM

R-6

650 CFM

R-7

350 CFM

R-6

750 CFM

R-7

360 CFM

R-7

305 CFM

6"ø S

A

6"ø S

A

6"ø S

A

12"x12" S A

5"ø P

A

20"ø P

A

12"ø P

A 10"ø

P A

8"ø P

A

6"ø P

A

12"ø P

A

6"ø PA

8"x10" S A

18"x14" S A

S-12

349 CFM

S-12

349 CFM

S-12

349 CFM

S-12

349 CFM

S-12

349 CFM

S-12

370 CFM S-12

350 CFM

S-12

365 CFM

S-12

359 CFM

10"x 8" S

A

10"x 8" S

A

10"x 8" S

A

10"x 10" S

A

12"x12" S A

10"x 8" S

A S-12

359 CFM

S-12

359 CFM

S-12

359 CFM

S-12

359 CFM

VAV-5

120-349

VAV-5

120-349

C E N ENFO

SE

ENOIS AL

GN

I

E

AT

P R

S

T K

E

C.

CHRISTOPHER

KEATH

L I S

D RE

Y

EFO K

C

TN

U

18328

NOTE:

IT IS NOT INTENDED THAT THE PLANS SHOW ALL OFFSETS IN PIPES, CONDUITS, AND DUCTS REQUIRED FOR INSTALLATION OF THE WORK. DETAILS AND SECTIONS ARE INCLUDED FOR SOME AREAS TO SHOW INTENDED RELATIONSHIP OF THE WORK OF VARIOUS TRADES. IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR AND SUB-CONTRACTORS TO COORDINATE INSTALLATION OF THE WORK AND TO PROVIDE THE NECESSARY OFFSETS, TRANSFORMATIONS, AND FITTINGS REQUIRED. NO ADDITIONAL COMPENSATION WILL BE ALLOWED FOR CORRECTION CONFLICTS BETWEEN THE WORK OF VARIOUS TRADES. DETAILS AND SECTIONS ARE SHOWN FOR THE CONTRACTORS CONVENIENCEAND SHALL NOT BE CONSIDERED COMPLETE IN EVERY DETAIL.

OAKWOOD - RENOVATION OF COTTAGES 111, 112 & 117

2441 US HIGHWAY 27, SOMERSET - PULASKI COUNTY, KY

Architectural Investments

222 SOUTH FIRST STREET - SUITE 206

LOUISVILLE, KENTUCKY 40202-1367

PHONE: 502-562-9220 FAX: 502-589-1571

[P lo tS ta m p

E v a l]

M A Y architectural investments

REVISION HISTORY OF THIS DRAWING

DRAWING NO.

DECA REVIEWED

DECA LOG #

DESCRIPTION OF REVISIONS DATE DESCRIPTION OF REVISIONS DATE

DRAWING INFORMATION

A & E FILE NO.

DRAWING DATE

DRAWN BY

CHECKED BY

PHASE

RTA DATE

COMMONWEALTH OF KENTUCKY

FINANCE AND ADMINISTRATION CABINET

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

FRANKFORT, KENTUCKY

ACCOUNT NO.

2023.09.20

729 - C 9SE - OW40 - 00

CK

21303

2022.09.20

CK

HVAC PLAN - COTTAGES 111 & 112

H11-10

C - RTA

ROOM SCHEDULE

ROOM NUMBER ROOM NAME

8-Q Space

1100 LIVING

1101 HALL

1102 BEDROOM

1103 BATH

1104 BEDROOM

1105 BEDROOM

1106 BATH

1107 BEDROOM

1108 JAN

1109 BEDROOM

1110 BATH

1111 BEDROOM

1112 I.T.

1113 TOILET

1114A OFFICE

1114B MED / CHART

1115 THERAPY / VISIT

1116 DINING

1117 KITCHEN

1117A PANTRY

1118A LAUNDRY

1118C CLEAN LIN

1118S SPOILED UTILITY

1119 STAFF LOUNGE

1120 LIVING

1121 HALL

1122 BEDROOM

1123 BATH

1124 BEDROOM

1125 BEDROOM

1126 BATH

1127 BEDROOM

1128 JAN

1129 BEDROOM

1130 BATH

1131 BEDROOM

1132 OFFICE

1134 TOILET

SCALE: 1/8" = 1'-0"

GROUND FLOOR HVAC - NEW

CODED NOTES:

1 FLUE AND COMBUSTION AIR PIPING UP TO CONCENTRIC VENT THRU ROOF. PIPING SHALL BE PER MANUFACTURER'S GUIDELINES

AND RATED FOR 200 DEG F MINIMUM.

2 REMOTE OPERATED DAMPER IN DUCTWORK.

3 MAKE CONNECTION TO PRIMARY AIR DUCT USING BELLMOUTH FITTING.

4 STACKED TERMINAL UNITS SO THAT THEY ARE ACCESSIBLE THROUGH ONE ACCESS DOOR.

5 INSTALL TEMPERATURE SENSOR RECESSED IN WALL WITH STAINLESS STEEL COVER PLATE. STAFF HVAC CONTROL SYSTEM

PASSWORD SHALL ALLOW CHANGES TO HEATING AND COOLING SETPOINTS.

6 PROVIDE AND INSTALL REMOVABLE ASPEN MINI BLANC CONDENSATE PUMP.

7 VENT DRYER TO ROOF ACCORDING TO MANUFACTURERS INSTRUCTIONS. PROVIDE ROOF CAP VENT COVER WITH BIRD SCREEN.

8 MOUNT RECIRCULATION HOOD ABOVE RANGE. HOOD TO BE PROVIDED BY OWNER.

9 24"x24" ACCESS DOOR (REFER TO SPECIFICATION NO. 08315).

10 BID SHALL INCLUDE ADDITIONAL ACCESS DOOR IN EQUIPMENT PIT. CONSTRUCTION OF ACCESS DOOR SHALL BE INDENTICAL TO EXISTING. COORDINATE EXACT LOCATION WITH OWNER AFTER ALL COMPONENTS ARE INSTALLED. COMPONENTS SHALL BE

INSTALLED SO THAT ALL EQUIPMENTS IS FULLY ACCESSIBLE THRU TWO ACCESS DOORS.

1 Addendum #2 2/8/24

T

T

T T

T

T

T

T

T

T

T

MAIN SUPPLY AND RETURN AIR DUCT

UP FROM FLOOR BELOW TO ABOVE

THIS FLOOR CEILING.

"ø

E A

EF-1

30"x10" SA24"x10" SA16"x10" SA

"ø E

A

6"ø EA

12"x12" SA

14"x12" SA

20"x12" SA

S-9

719 CFMS-8

500 CFM

36"x6" SA

S-8

633 CFM

"x

S A

"x

S A

S-12

365 CFM

12"ø PA

"x

P A

"ø

E A

1709 1711 1700

1707 1705 1704 1702 1712 1713

1719C

1719A

1716A

1719B

L-1

1710 EF-1

"ø

E A

S-12

370 CFM2

S-12

365 CFM

EF-1

8"ø EA

S-12

365 CFM

2 2

S-12

430 CFM

VAV-12

438-1460

IU-1

VAV-12

340-1133

VAV-10

222-741

S-8

599 CFM

VAV-8

129-430

58"x18" PA

S-9

719 CFM

VAV-12

338-1127

VAV-12

438-1460

"x

P A

S-8

627 CFM

S-12

359 CFM

"x

S A

EF-1

S-12

359 CFM

EF-1

L-1

12"ø EA

S-12

365 CFM

EF-1

6"ø EA

S-12

365 CFM

S-12

365 CFM

"ø

E A

EF-110

"ø

E A

"x

S A

S-8

500 CFM

S-13

719 CFM

VAV-10

216-719

R-5

1941 CFM

VAV-5

50-71

S-11

71 CFM

6"ø EA

6"ø EA R-1

256 CFM

VAV-5

50-120

S-11

120 CFM

VAV-6

95-316

S-6

316 CFM

DEMOLITION NOTE:

REMOVE ALL HVAC ITEMS (EQUIPMENT, PIPING, DUCTWORK, ETC.) IN IT'S ENTIRETY.

SEE SPECIFICATIONS FOR LIST OF EQUIPMENT TO BE TURNED OVER TO OWNER.

UNDERSLAB DUCTWORK AND PIPING MAY BE ABANDONED WHERE IT DOES NOT

INTERFERE WITH INSTALLATION OF NEW WORK.

WHERE DUCTWORK, AND PIPING ARE ABANDONED, ENDS SHALL BE REMOVED TO

BELOW SLAB, PLUGGED WITH CONCRETE, AND SLAB REPARED AS REQUIRED FOR

NEW CONSTRUCTION.

VAV-10

216-719

S-12

370 CFM

S-6

316 CFM

.19 .18 .17 .15 .14 .13.16

.12 .11

.10

.C.

.1

.2

.3

.5

.6

.4

.8

.9

VAV-5

120-370

VAV-5

120-365

VAV-5

120-370

S-12

365 CFM

S-12

365 CFM

R-7

305 CFM

R-7

310 CFM

R-7

305 CFM

R-6

1020 CFM

R-7

370 CFM

R-7

305 CFM

R-7

305 CFM

5"ø PA

5" ø P

A

5" ø P

A

5"ø PA

R-7

310 CFM

R-7

305 CFM

R-7

305 CFM

R-7

305 CFM

R-7

305 CFM

R-7

305 CFM

R-7

305 CFM

R-6

630 CFM

R-7

305 CFM

R-7

305 CFM

R-6

1015 CFM

R-6

539 CFM

VAV-8

129-430

VAV-10

216-719

VAV-5

50-71

VAV-5

120-365

EF-1

EF-1

EF-1

EF-1

C E N ENFO

SE

ENOIS AL

GN

I

E

AT

P R

S

T K

E

C.

CHRISTOPHER

KEATH

L I S

D RE

Y

EFO K

C

TN

U

18328

NOTE:

IT IS NOT INTENDED THAT THE PLANS SHOW ALL OFFSETS IN PIPES, CONDUITS, AND DUCTS REQUIRED FOR INSTALLATION OF THE WORK. DETAILS AND SECTIONS ARE INCLUDED FOR SOME AREAS TO SHOW INTENDED RELATIONSHIP OF THE WORK OF VARIOUS TRADES. IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR AND SUB-CONTRACTORS TO COORDINATE INSTALLATION OF THE WORK AND TO PROVIDE THE NECESSARY OFFSETS, TRANSFORMATIONS, AND FITTINGS REQUIRED. NO ADDITIONAL COMPENSATION WILL BE ALLOWED FOR CORRECTION CONFLICTS BETWEEN THE WORK OF VARIOUS TRADES. DETAILS AND SECTIONS ARE SHOWN FOR THE CONTRACTORS CONVENIENCEAND SHALL NOT BE CONSIDERED COMPLETE IN EVERY DETAIL.

OAKWOOD - RENOVATION OF COTTAGES 111, 112 & 117

2441 US HIGHWAY 27, SOMERSET - PULASKI COUNTY, KY

Architectural Investments

222 SOUTH FIRST STREET - SUITE 206

LOUISVILLE, KENTUCKY 40202-1367

PHONE: 502-562-9220 FAX: 502-589-1571

[P lo tS ta m p

E v a l]

M A Y architectural investments

REVISION HISTORY OF THIS DRAWING

DRAWING NO.

DECA REVIEWED

DECA LOG #

DESCRIPTION OF REVISIONS DATE DESCRIPTION OF REVISIONS DATE

DRAWING INFORMATION

A & E FILE NO.

DRAWING DATE

DRAWN BY

CHECKED BY

PHASE

RTA DATE

COMMONWEALTH OF KENTUCKY

FINANCE AND ADMINISTRATION CABINET

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

FRANKFORT, KENTUCKY

ACCOUNT NO.

2023.09.20

729 - C 9SE - OW40 - 00

CK

21303

2022.09.20

CK

HVAC PLAN - COTTAGE 117

H17-10

C - RTA

SCALE: 1/8" = 1'-0"

GROUND FLOOR HVAC - NEW

ROOM SCHEDULE

ROOM NUMBER ROOM NAME

1700 LIVING

1701 HALL

1702 BEDROOM

1703 BATH

1704 BEDROOM

1705 BEDROOM

1706 BATH

1707 BEDROOM

1708 JAN

1709 BATHING

1710 BATH

1711 BEDROOM

1712 OFFICE / MED / CHART

1713 THERAPY / VISIT

1714 TOILET

1716 KITCHEN

1716A PANTRY

1717 DINING

1718 IT

1719A CLEAN LIN.

1719B LAUNDRY

1719C SOILED

1720 LIVING

1721 HALL

1722 BEDROOM

1723 BATH

1724 BEDROOM

1725 BEDROOM

1726 BATH

1727 BEDROOM

1728 JAN

1729 BEDROOM

1730 BATH

1731 BEDROOM

1732 STAFF LOUNGE

1733 OFFICE

1734 TOILET

CODED NOTES:

1 FLUE AND COMBUSTION AIR PIPING UP TO CONCENTRIC VENT THRU ROOF. PIPING SHALL BE PER

MANUFACTURER'S GUIDELINES AND RATED FOR 200 DEG F MINIMUM.

2 REMOTE OPERATED DAMPER IN DUCTWORK.

3 STACK TERMINAL UNITS SO THAT THEY ARE ACCESSIBLE THRU ONE ACCESS DOOR.

4 MAKE CONNECTION TO PRIMARY AIR DUCT USING BELLMOUTH FITTING.

5 INSTALL TEMPERATURE SENSOR RECESSED IN WALL WITH STAINLESS STEEL COVER PLATE. STAFF HVAC

CONTROL SYSTEM PASSWORD SHALL ALLOW CHANGES TO HEATING AND COOLING SETPOINTS.

6 VENT DRYER TO ROOF ACCORDING TO MANUFACTURERS INSTRUCTIONS. PROVIDE ROOF CAP VENT COVER

WITH BIRD SCREEN.

7 MOUNT RECIRCULATION HOOD ABOVE RANGE. HOOD TO BE PROVIDED BY OWNER.

8 BID SHALL INCLUDE ADDITIONAL ACCESS DOOR IN EQUIPMENT PIT. CONSTRUCTION OF ACCESS DOOR SHALL BE IDENTICAL TO EXISTING. COORDINATE EXACT LOCATION WITH OWNER AFTER ALL COMPONENTS ARE INSTALLED. COMPONENTS SHALL BE INSTALLED SO THAT ALL EQUIPMENT IS FULLY ACCESSIBLE THRU TWO

ACCESS DOORS.

9 24"x24" ACCESS DOOR (REFER TO SPECIFICATION NO. 08315).

T

T

T T

T

T

T

T

T

T

T

T

OUT DOOR UNIT FOR

INDOOR VRF UNIT.

RH-2

2.0

RH-6

2.5

RH-4

2.0

RH-4

2.0

RH-6

2.5

1" HWS

3/4" HWS

1 1/4" HWS

3/4" HWS 1 1/4" HWR

1" HWR

1" HWS

3/4" HWR

3/4" HWS

3/4" HWR

3/4" HWS

1 1/4" HWR

1 1/4" HWS

3/4" HWS

3/4" HWS

3/4" HWS

1" HWS

3/4" HWS

3/4" HWS

3/4" HWS

3/4" HWS

3/4" HWS

3/4" HWR

1" HWR

2" HW

S

/2 H

W S

H

W S

1 1/2" HWS

3/4" HWR

2" HWR

3/4" HWR

3/4" HWR

/2 H

W R

3/4" HWR

3/4" HWR

1 1/2" HWR

3/4" HWR

1" HWR

3/4" HWR

3/4" HWR

1709 1710 1711 1700

1707 1705 1704 1702 1712 1713

1716A

1719A

1719C

1719B

RH-8

4.0

RH-8

4.0

RH-6

2.5

RH-6

2.5

IU-1

3 3

RH-6

2.5 3

RH-6

2.5

RH-1

1.0

RH-1

1.0

RH-2

2.0

RH-8

4.0

OU-1 OU-2

OU-3 OU-4

REFR

3/4" CD

2 2

.19

.A

.18 .17

.B

.C

.15 .14 .13.16

.12 .11

.10

.A.

.B.

.C.

.1

.2

.3

.5

.6

.7

.4

.8

.9

VAV-5

120-370

RH-1

1.0

VAV-5

120-365

RH-1

1.0

3/4" HWR

3/4" HWS

3/4" HWS

3/4" HWR

3/4" HWR

3/4" HWS

3/4" HWS

3/4" HWR

RH-1

1.0

RH-1

1.0

R E F R

R E F R

REFR

REFR

1" CD

2" HWR

2" HWS

2" H W

S

2" H W

R

2" HW

S

2" HW

R

3" HWS

3" HWR

ET-1

PU-1A

AS-1

B-2B

IU-2

OU-1 OU-2

OU-4OU-3

PU-2

CV-5

FILL

REFR

1 9

PU-1B

1"

B-2A

AHU-1

VFD-1B

VFD-1A

3/4" CD

.A

.B

.C

.13

.12 .11

.A.

.B.

.C. .6

.7

.8

.9

C E N ENF

O

SE

ENOIS

AL

GN

I

E

AT

P R

S

T K

E

C.

CHRISTOPHER

KEATH

L I S

D RE

Y

EFO K

C

TN

U

18328

NOTE:

IT IS NOT INTENDED THAT THE PLANS SHOW ALL OFFSETS IN PIPES, CONDUITS, AND DUCTS REQUIRED FOR INSTALLATION OF THE WORK. DETAILS AND SECTIONS ARE INCLUDED FOR SOME AREAS TO SHOW INTENDED RELATIONSHIP OF THE WORK OF

VARIOUS TRADES. IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR AND SUB-CONTRACTORS TO COORDINATE INSTALLATION OF THE WORK AND TO PROVIDE THE NECESSARY OFFSETS, TRANSFORMATIONS, AND FITTINGS REQUIRED. NO ADDITIONAL

COMPENSATION WILL BE ALLOWED FOR CORRECTION CONFLICTS BETWEEN THE WORK OF VARIOUS TRADES. DETAILS AND SECTIONS ARE SHOWN FOR THE CONTRACTORS CONVENIENCEAND SHALL NOT BE CONSIDERED COMPLETE IN EVERY DETAIL.

OAKWOOD - RENOVATION OF COTTAGES 111, 112 & 117

2441 US HIGHWAY 27, SOMERSET - PULASKI COUNTY, KY

Architectural Investments

222 SOUTH FIRST STREET - SUITE 206

LOUISVILLE, KENTUCKY 40202-1367

PHONE: 502-562-9220 FAX: 502-589-1571

[P lo tS ta m p

E v a l]

M A Y architectural investments

REVISION HISTORY OF THIS DRAWING

DRAWING NO.

DECA REVIEWED

DECA LOG #

DESCRIPTION OF REVISIONS DATE DESCRIPTION OF REVISIONS DATE

DRAWING INFORMATION

A & E FILE NO.

DRAWING DATE

DRAWN BY

CHECKED BY

PHASE

RTA DATE

COMMONWEALTH OF KENTUCKY

FINANCE AND ADMINISTRATION CABINET

DEPARTMENT FOR FACILITIES AND SUPPORT SERVICES

DIVISION OF ENGINEERING AND CONTRACT ADMINISTRATION

FRANKFORT, KENTUCKY

ACCOUNT NO.

2023.09.20

729 - C 9SE - OW40 - 00

CK

21303

2022.09.20

CK

HVAC PIPING PLAN - COTTAGE 117

H17-20

C - RTA

SCALE: 1/8" = 1'-0"

GROUND FLOOR HVAC PIPING - NEW

ROOM SCHEDULE

ROOM NUMBER ROOM NAME

1700 LIVING

1701 HALL

1702 BEDROOM

1703 BATH

1704 BEDROOM

1705 BEDROOM

1706 BATH

1707 BEDROOM

1708 JAN

1709 BATHING

1710 BATH

1711 BEDROOM

1712 OFFICE / MED / CHART

1713 THERAPY / VISIT

1714 TOILET

1716 KITCHEN

1716A PANTRY

1717 DINING

1718 IT

1719A CLEAN LIN.

1719B LAUNDRY

1719C SOILED

1720 LIVING

1721 HALL

1722 BEDROOM

1723 BATH

1724 BEDROOM

1725 BEDROOM

1726 BATH

1727 BEDROOM

1728 JAN

1729 BEDROOM

1730 BATH

1731 BEDROOM

1732 STAFF LOUNGE

1733 OFFICE

1734 TOILET

SCALE: 1/8" = 1'-0"

BASEMENT HVAC PIPING - NEW

CODED NOTES:

1 PIPING OFFSET FOR CLARITY. BRACKET PIING TO WALL; DO NOT

SUPPORT PIPING FROM GRATING.

2 PROVIDE 24"x24" ACCESS DOOR IN DRYWALL CEILING, POSITION ACCESS

DOOR SO THAT ALL CONTROL PANELS AND HEATING COIL VALVES ARE

ACCESSIBLE THRU DOORS.

3 PIPE REHEAT COILS SO THAT ALL VALVES ARE ACCESSIBLE THRU

DRYWALL CEILING ACCESS DOOR.

4 HVAC HOT WATER SUPPLY AND RETURN PIPING UP TO UPPER LEVERL.

5 HVAC HOT WATER SUPPLY AND RETURN PIPING DOWN TO LOWER

LEVEL.

6 REFRIGERANT PIPING UP TO UPPER LEVEL.

7 DX UNIT 3/4" CONDENSATE FROM UPPER LEVEL.

8 CONNECT FILL PIPING TO AUTOMATIC AIR ELIMINATOR CONNECTION AT

TOP OF AIR SEPARATOR.

9 REFRIGERANT PIPING SHALL BE SIZED BY EQUIPMENT MANUFACTURER.

SUBMIT SIZING AND LAYOUT.

10 REFRIGERANT PIPING DOWN TO MECHANICAL ROOM.

11 3/4" CONDENSATE LINE DOWN TO MECHANICAL ROOM BELOW.

12 PROVIDE AND INSTALL REMOVABLE ASPEN MINI BLANC CONDENSATE

PUMP.