Addendum 2 Resinous Flooring Specification Sheet.pdf

ZERO VOC

DUR-A-CHIP™

Topcoat - Clear Armor-Top

Grout Coat - Clear Dur-A-Glaze #4, or Ultra Clear

Second Chip Broadcast - Clear Dur-A-Glaze #4 and Broadcast of

Macro or Micro Decorative Vinyl Chip

Chip Broadcast - Dur-A-Gard OPF and Broadcast of Macro or

Micro Decorative Vinyl Chip

Primer - Dur-A-Glaze WB, Dur-A-Glaze MVP*, or Elast-O-Coat

Prepared Substrate - Concrete Surface Profile (CSP) of 3-4

*Dur-A-Glaze MVP Primers include any available version of

Dur-A-Glaze MVP Primer.

SYSTEM OVERVIEW

DUR-A-CHIP is a seamless, decorative flooring system consisting of 100% solids epoxy body coats with decorative Macro or Micro vinyl chip broadcasts, finished with a durable urethane topcoat ensuring excellent wear and chemical resistance.

FEATURES & BENEFITS

· Long Lasting Seamless flooring systems for years of service with minimal maintenance

· Wear / Chemical Resistant High quality urethane topcoat for superior wear and chemical resistance

· Decorative Multiple blends of Macro or Micro vinyl chip blends for a unique look

· Non Slip Textured finishes aid in a safer floor, even when wet

COMMON USE SITES

· Locker Rooms

IMPORTANT!

Before using DUR-A-FLEX products, read and understand its accompanying Safety Data Sheet & Application Instructions for important safety information.

STANDARD TERMS AND CONDITIONS OF SALE, INCLUDING STANDARD WARRANTY APPLY - VISIT DUR-A-FLEX.COM FOR THE LATEST VERSION

CONNECTICUT | GEORGIA | ILLINOIS | CALIFORNIA

TOLL FREE 800-253-3539 | 860-528-9838 | DUR-A-FLEX.COM

230424

SHALE RED ROCK

OCEAN

ACADIA GALAXY

SEA GLASS

OLIVE STONE

TUSCANY SAHARA

MICRO CHIP

MACRO CHIP

EARTHSTONE

FLINT OLIVINE

ADOBE

CARBON FIELDSTONE

PEBBLE

LEDGE

MESA FOSSIL

WHEAT PEWTER

COBALT

MARINA COBBLESTONE

CALYPSO

OYSTER SHELL

SCARLET GLACIER

COLORS

Available in a wide variety of standard Macro, Micro, Earthstone, RX Designer, or Claystone Designer vinyl chip blends. For a full list of available colors visit DUR-A-FLEX.COM.

FARMINGTON HAVENGOODWIN ENFIELDWINDSOR

AVON WENDELL HAMPTONHUDSON

HARDWICK

HARVARD

HADLEY

ALPINE CHERRY

LAWN

FORGE BASIN

PATHWAY

CANARY

INDIGO

RX DESIGNER BLENDS

CLAYSTONE DESIGNER BLENDS

APPLICATION INSTRUCTIONS

DUR-A-CHIP is applied by broadcast method.

When recommended spread rates are followed, a double broadcast of either MICRO or MACRO decorative chip will produce a nominal system thickness of 60 mils. Surface finish can be smooth or textured for added slip resistance.

SURFACE PREPARATION

Surface must be clean, sound, dry and free of all oil, grease, detergent film, sealers and/or curing compounds. A surface profile of CSP 3 is appropriate for most applications. All paint should be removed unless it is a properly applied, totally de-glossed, high quality epoxy. Upper level rooms, like mechanical rooms, bathrooms, or wet process areas that have space below should receive ELAST-O-COAT seamless fluid applied membrane. Please refer to the DUR-A-FLEX Surface Preparation Guide on our website for detailed instructions. No epoxy coatings should be applied unless surface temperature is a minimum of 5 degrees F above dew point. See Dew Point Calculation Chart on our website for detailed instructions.

NOTE: For each application of material and before mixing, mark your batches to ensure you achieve your spread rate targets. This is best accomplished by dividing your target spread rate by the width of the area being coated (or your planned wet edge). Example: If your spread rate is 100 square feet and your area is 20 feet wide you would make a mark every 5 feet (100 divided by 20 = 5).

MIXING AREA

Select a convenient mix area and protect the surface from spillage by covering with a layer of cardboard and/or sheet of plastic. Be generous with the amount of space you allocate for this function. The more comfortably your mixer works, the less likely you are to have a “mix error”. Make ready all necessary tools, mix and measure containers, etc. DO NOT MIX ANY EPOXY UNTIL READY FOR IMMEDIATE USE. Once hardener and resin are combined, it must be used without delay. Apply masking tape wherever coating is intended to stop. To obtain neat, straight, chip resistant edges at termination points and/ or drains, a “keyed edge” must be installed.

PRE-PATCH

Pre-patch badly eroded, spalled or cracked areas with the proper material: Use ELAST-O-COAT thickened with NO SAG 1 for moving joints and DUR-A-GLAZE #4 mixed with NO-SAG 2 or Flintshot for non-moving joints. BE SURE TO LEAVE AS

LITTLE EXCESS AS POSSIBLE AS IT WILL BE HIGHLIGHTED

IN SUCCESSIVE STEPS. Sanding or grinding pre-patch areas will help in hiding deviations.

JOINT GUIDELINES

Refer to the Joint Guidelines for complete details on our website.

PRIMING

All surfaces must be primed with DUR-A-GLAZE WB Primer, DUR-A-GLAZE MVP Primers*, or ELAST-O-COAT as soon as the surface has been prepared.

*Dur-A-Glaze MVP Primers include any available version of Dur-A-Glaze MVP, MVP2, or MVP3 Primer.

95 Goodwin Street East Hartford, CT 06108

Tel: 800-253-3539 • Fax: 860-528-2802 • www.dur-a-flex.com • contact_us@dur-a-flex.com

DUR-A-CHIP DECORATIVE EPOXY FLOORING

IMPORTANT! Read these instructions carefully several days prior to starting your work. Seek answers to any questions you may have before you begin. DUR-A-FLEX, Inc. maintains a Technical Staff that will be glad to answer your questions and give you advice pertaining to your particular installation.

IMPORTANT!

Before using DUR-A-FLEX products, read and understand its accompanying Safety Data Sheet.

STANDARD TERMS AND CONDITIONS OF SALE, INCLUDING STANDARD WARRANTY APPLY - VISIT DUR-A-FLEX.COM FOR THE LATEST VERSION

CAUTION! As with all chemical products, individuals may have different reactions to exposure to specific products. This is dependent upon many factors, including the individual’s personal characteristics, the size of the installation, the ventilation available, the intensity of the exposure or the length of the exposure. Individuals may experience discomfort during the installation process of one product, but not another.

In some cases this is experienced as a skin irritation and in others it is experienced as an inhalant irritation. Typically, it disappears once the exposure is eliminated. In some cases people can become “sensitized” to a product and experience the discomfort every time there is exposure without Personal Protective Equipment (“PPE”).

To protect yourself from various exposures or discomfort during the mixing and application of our products, we recommend covering exposed skin including, using gloves, long sleeves, safety glasses and a respirator such as the 3M 8577 P95 Universal Disposable Carbon Respirator or a cartridge respirator.

Use only as directed. KEEP OUT OF REACH OF CHILDREN.

Do not reseal moisture-contaminated hardener. This will result in carbon dioxide generation or possible violent rupture of container.

220715

APPLICATION METHOD

A. Prepare the surface as outlined in the DUR-A-FLEX

Surface Preparation Guide.

B. Measure out 1/2 gallon of DUR-A-GARD OPF hardener and

1 gallon of DUR-A-GARD resin. When combining, be sure to add the hardener first. Add the resin and scrape out the container. Be careful to pour both hardener and resin into the center of the mixing pail. Mix the blended epoxy with a slow speed power drill with a Jiffler type mixing blade for 2 minutes. Always scrape the sides and bottom of the measuring bucket to assure thorough blending.

C. Apply the mixed DUR-A-GARD using a non-shed 18,” 3/8 inch nap roller at 300-350 Sq Ft per gallon by the dip and roll method. Back roll with a quality, non-shed roller 18,” 3/8 inch nap roller.

D. Broadcast MICRO or MACRO decorative chip. While wearing spiked shoes, walk on the wet epoxy holding a 2-gallon container and broadcast the decorative chip until the floor appears dry (0.10 lbs per SF for macro and

0.15 lbs per SF for micro chips). Be sure to keep moving while throwing the chips UP into the air so it falls vertically onto the epoxy. IMPORTANT: Do not “seed” the edge that will be joining the next section. Be sure to leave a “WET EDGE” (a 24” strip “unseeded” to permit overlapping when proceeding onto next section). Do not walk on the decorative chip with spiked shoes. Be sure to keep any impurities out of the chips such as broom bristles, debris, etc. Allow to cure.

E. Sweep off the excess decorative chip using a stiff, clean, dry broom with synthetic bristles.

F. Scrape the floor with a trowel or floor scraper. Sweep and vacuum the floor again.

G. Measure out 1 part DUR-A-GLAZE #4 hardener and 2 parts DUR-A-GLAZE #4 resin and mix the blended epoxy for 2 minutes. Be sure to follow the procedures outlined in step (B). Mix only what you can apply within 5 - 10 minutes. NOTE: Do not use “Fast” Hardeners for topcoats as they yellow very quickly and could produce pinholes.

H. Apply the mixed DUR-A-GLAZE #4 WATER CLEAR at 100- 150 Sq Ft per gallon with a flat squeegee and back roll with a quality 18”, 3/8” non-shed roller.

I. Broadcast MICRO or MACRO decorative chip. Follow procedures outlined in step (D) above. Allow to cure.

J. Sweep off the excess decorative chip using a stiff, clean, dry broom with synthetic bristles.

K. Scrape the floor with a trowel or floor scraper. Sweep and vacuum the floor again.

L. Apply a coat of DUR-A-GLAZE #4 at 100-150 Sq Ft per gallon with a flat squeegee and back roll with a quality 18”, 3/8” non-shed roller. Follow the same procedure for mixing as outlined in step (F). For anti-slip properties, back roll Aluminum Oxide #54 to #36 into grout coat.

M. Apply Armor Top per Product Data Sheet instructions.

Remove all masking tape as you proceed, before it gets out of reach. Allow to cure.

IMPORTANT: Be sure to pour the hardener into the mixing bucket first, when working with the epoxy and vice versa when working with the urethane. Always scrape the sides and bottom of mixing container to assure thorough blending. USE SIGNS AND BARRIERS to keep traffic out of the area. Do not allow any water on coated surface for 24-48 hours. Chemical spillage must be prevented for approximately 5 days.

NOTE: Use DUR-A-SOLVE or a Xylene for clean up.

PRODUCT DATA SHEET

DESCRIPTION

DUR-A-CHIP SEAMLESS FLOORING is a decorative, “poured in place” flooring system consisting of liquid polymers and color-fast decorative chips. DUR-A-CHIP is designed to provide a terrazzo-like appearance. In addition to its seamless cleanability, it requires no waxing.

BENEFITS

• Easy Installation

• Low Odor

• Meets USDA, FDA, OSHA standards

• Easy To Use

• Good Abrasion Resistance

• Easy Maintenance

LIMITATIONS

This product is best suited for application in temperatures between 60°F and 90°F. Substrate must be clean, sound, and dry.

TYPICAL USES

COLORS

DUR-A-CHIP is available in MACRO or MICRO decorative chips. The MACRO and MICRO chips are available in standard blends, custom colors. Please refer to the MACRO, MICRO, and Earthstone Chip Color Chart.

PACKAGING

DUR-A-GARD OPF is available in 1-gallon and 5-gallon pails.

DUR-A-GLAZE #4 is available in 1-gallon, 5-gallon pails and drums. ARMOR TOP is available as kits. DUR-A-CHIP is available in 10 lb or in 40 lb boxes.

SURFACE PREPARATION

This product requires preparation in order to perform as expected. Substrate must be profiled clean, sound, and dry.

Please refer to the master Surface Preparation Guide on our website for more information.

APPLICATION METHOD

DUR-A-CHIP incorporates DUR-A-GARD OPF for the base coat and is grout coated with DUR-A-GLAZE #4 and top coated with ARMOR TOP.

GUIDE SPECIFICATIONS

This product is part of the DUR-A-FLEX family of polymer systems. Please contact DUR-A-FLEX for complete three part guide specs.

DRAWINGS AND DETAILS

Standard CAD drawings and details are available for coves, drains, breaches, transitions, etc. Please contact DUR-A-FLEX for actual drawings.

JOINT GUIDELINES

Refer to the Joint Guidelines for complete details on our website.

MOISTURE CONCERNS

Please refer to the Floor Evaluation Guidelines at www.dur-a-flex.com for complete details.

CHEMICAL RESISTANCE

This product is resistant to most common chemicals. Please refer to master Chemical Resistance Chart on our website for actual resistance to specific chemicals/reagents.

CLEANING

This product is considered to be a low maintenance flooring solution; however, certain textures and service environments require specific procedures. Please refer to the master Cleaning Guide on our website.

95 Goodwin Street East Hartford, CT 06108

Tel: 800-253-3539 • Fax: 860-528-2802 • www.dur-a-flex.com • contact_us@dur-a-flex.com

DUR-A-CHIP

Physical Property Test Method Result

Hardness, Shore D ASTM D-2240 75-80

Water Absorption ASTM D-570 0.04%

Flammability ASTM D-635 Self extinguishing

Flame Spread / NFPA-101 ASTM E-84 Class A

Tensile Strength ASTM D-638 3,700 psi

Flexural Strength ASTM D-790 4,700 psi

Compressive Strength ASTM D-695

ASTM C-579

16,000 psi 10,500 psi

Izod Impact (ft. Lb./in. notch) ASTM D-256 0.50

Bond Strength to Concrete ASTM D-4541 400 psi substrate fails

Elevated Temperature MIL D-3134 No slip or flow

Thermal Shock, 50 cycles of immersion in chilled & boiling water

MIL F-52505 No cracking or loss of adhesion

UV Resistance MIL F-52505 No chalking or loss of adhesion

Abrasion Resistance, CS-17 Wheel, Wgt.

Loss, 100gm. Load, 1000 cycles

ASTM D-4060 4 mg loss with (Armor Top Gloss with grit)

Static Coefficient of Friction* ANSI B101.1 >0.6

Dynamic Coefficient of Friction - Wet* ANSI A326.3 >0.42

VOC Content 0 g/L

IMPORTANT!

Before using DUR-A-FLEX products, read and understand its accompanying Safety Data Sheet & Application Instructions for important safety information.

STANDARD TERMS AND CONDITIONS OF SALE, INCLUDING STANDARD WARRANTY APPLY - VISIT DUR-A-FLEX.COM FOR THE LATEST VERSION

DUR-A-CHIP

TECHNICAL INFORMATION

Salt Spray Resistance, 25% solution at 90°F No effect after 100 hours

Toxicity Non-toxic, meets USDA requirements

201028

*Dur-A-Flex flooring systems can be built to meet or exceed the requirements of Static or Dynamic Coefficient of Friction testing per installation. Contact your Dur-A-Flex territory sales manager or tech representative for more information on alternative textures, grit/grip additives, or smooth coatings for your specific environment. A sample should always be obtained and tested prior to purchase for any non-slip flooring system.

EPOXY & POLY-THANE INSTALLATION CHECKLIST

CONNECTICUT | GEORGIA | ILLINOIS | CALIFORNIA

TOLL FREE 800-253-3539 | 860-528-9838 | DUR-A-FLEX.COM

230110

� 1/2" 450 rpm heavy duty drill

� 5 gallon power mixer

� 5" & 3" jiffler blades

� Extension cords

� Mix & measure kits

� 5 gallon pails: metal & plastic

� 2 gallon pails

� 1 gallon pails

� Rags

� Dur-A-Solve (or similar xylene based solvent)

� Cardboard and plastic for mix station

� Paint sticks

� Utility Knife

� 5 in 1 Tool

� Blue tape

� Duct tape

� Garbage bags

� Floor machine / buffer/ sander

� Sanding discs: 20 & 36 grit

� Sanding screens: 80 &120 grit

� Palm sander

� Latex gloves (or similar)

� Respirator

� Hard hat

� Safety glasses

� Knee pads

� Spike shoes

� Dust masks

� LED / Halogen lighting

� 1/8” Cove strip

� Vacuum

� Stiff bristle brooms

� Squeegees: flat & notched

� Gauge rake for self-level applications

� 18” roller covers, frames, pans

� 9” roller covers, frames, pans

� 3" chip brushes

� Margin trowels

� Flat finish trowels: 3" x 12" & 4" x 14"

� Cove trowels: 4" & 6" (have 2 of each)

� Rub stones (Marshalltown)

� Drum valves 2" & 3/4"

� Drum wrench

� Drum carts

� Leaf blowers (electric or battery powered)

NOTE: Read and understand the Application Instructions and Product Data Sheets before working with any Dur-A-Flex products. Proper PPE is the responsibility of the individual using the products. To protect yourself from various exposures or discomfort during the mixing and application of our products, we recommend covering exposed skin including, using gloves, long sleeves, safety glasses and a respirator such as the 3M 8577 P95 Universal Disposable Carbon Respirator or a cartridge respirator.