A.2.11.3 HAZMAT REPORT.pdf

INSPECTION REPORT FOR

ASBESTOS, LEAD & ARSENIC

REPLACE HVAC SYSTEM

US ARMY MUSEUM

FORT DERUSSY, OAHU, HAWAII

Prepared for:

Nagamine Okawa Engineers, Inc.

1003 Bishop Street, Suite 2025

Honolulu, Hawaii 96813

Prepared by:

EnviroQuest, Inc.

98-029 Hekaha Street, Suite 21

Aiea, Hawaii 96701 808.486.5881 eqi@enviroquestinc.com

March 28, 2018

ENVIROQUEST Project 11576.2

EQI Project No. 11576.2 ii

TABLE OF CONTENTS

EXECUTIVE SUMMARY

1.0 INTRODUCTION

2.0 ASBESTOS

2.1 Methodology

2.2 Results

3.0 LEAD

3.1 Methodology

3.2 Results

4.0 ARSENIC

4.1 Methodology

4.2 Results

5.0 SUMMARY

5.1 Asbestos

5.2 Lead

5.3 Arsenic

6.0 LIMITATIONS

TABLES

Table 1 - Homogeneous Material Summary Table 2 - Lead Paint Summary Table 3 - Arsenic Sample Summary

APPENDICES

1. Asbestos Laboratory Analytical Report

2. Lead Laboratory Analytical Report

3. Arsenic Laboratory Analytical Report

EQI Project No. 11576.2 1

EXECUTIVE SUMMARY

ENVIROQUEST, INC. (EQI) was retained by Nagamine Okawa Engineers, Inc. to conduct a limited hazardous material inspection of the US Army Museum, Fort DeRussy, Honolulu, HI. The inspection was conducted on November 9, 2017 and February 16, 2018.

The objective of our inspection was to determine the location of asbestos-containing materials (ACMs), lead-based paints (LBPs) and arsenic containing materials (ASCMs) that may be impacted by the planned replacement of existing HVAC system.

Asbestos

Asbestos containing materials were not identified in this inspection. The National Emission Standard for Hazardous Air Pollutants (NESHAP), 40 CFR 61 Part M, defines asbestos containing materials as those which contain greater than 1% asbestos.

Lead

Based on the laboratory analytical results from this inspection, the listed building component was painted or coated with lead-based paint (LBP).

Color Location Condition

Beige Concrete ceiling Intact

United States Environmental Protection Agency (EPA) defines lead-based paint as paint or other coatings containing lead equal to, or in excess of, 0.5% by weight. Lead at concentrations below the EPA guideline was also detected in other paint/coatings (see Table 2). The contractor’s employees removing or disturbing the painted material also must be informed that it contains lead and must have received training under United States Occupational Safety and Health Administration (OSHA) 29 CFR 1926.62 Lead.

If the painted components containing the lead are scheduled for demolition, composite samples of the expected building waste generated should be collected for Toxicity Characteristic Leaching Procedure (TCLP) analysis to determine the waste disposal characterization. Hawaii Administrative Rules, Title 11, Department of Health, Chapter 261, Hazardous Waste Management allows a maximum concentration of lead contaminant by TCLP at 5.0 mg/L. TCLP results for lead exceeding the 5.0 mg/L threshold requires the material to be disposed of as hazardous waste. Results below this threshold allow for the materials to be disposed of as construction debris.

Arsenic

Arsenic containing materials were not identified in this inspection.

EQI Project No. 11576.2 2

1.0 INTRODUCTION

This report presents the results of the limited hazardous material inspection of the US Army Museum, Fort DeRussy, Honolulu, HI. The inspection was conducted on November 9, 2017 and February 16, 2018.

The objective of our inspection was to determine the location of ACMs, LBPs and ASCMs that may be impacted by the planned replacement of existing HVAC system.

EQI Project No. 11576.2 3

2.0 ASBESTOS

Thirty six samples were collected from suspect asbestos-containing materials. The samples were collected by the Hawaii Department of Health (HDOH) accredited Asbestos Building Inspector, Mr. Benson Eugenio (HIASB-3029).

2.1 Methodology

Prior to sampling, EQI visually surveyed the project areas for suspect asbestos-containing materials and homogeneous areas (areas that have uniform color, texture, and appearance.)

Suspect materials were divided into friable and non-friable materials and placed in one of the following EPA categories:

• Surfacing Materials (sprayed or troweled-on materials)

• Thermal Systems Insulations (materials generally applied to various mechanical systems)

• Miscellaneous Materials (any materials which do not fit in the above categories)

Sampling methodology followed the general guidelines for bulk asbestos sampling as presented in Section 40, Part 763 (AHERA) of the Code of Federal Regulations (CFR) and Hawaii Administrative Rules (HAR) 11-501 and 11-502.

2.2 Results

Samples were submitted to Forensic Analytical in Rancho Dominguez, California. The samples were analyzed by polarized-light microscopy (PLM), using EPA Method 600/R-93-116, Visual Area Estimation.

Forensic Analytical is accredited for bulk asbestos analysis through successful participation in the US Department of Commerce, National Institute of Standards and Technologies (NIST), National Voluntary Laboratory Accreditation Program (NVLAP). The laboratory is currently registered to provide asbestos laboratory services in the State of Hawaii under Title 11 of the Hawaii Administrative Rules (HAR), Chapter 504.

Based on the laboratory analytical report, none of the 36 samples were identified as ACM. The National Emission Standard for Hazardous Air Pollutants (NESHAP), 40 CFR 61 Part M, defines asbestos containing materials as those which contain greater than 1% asbestos. In accordance with NESHAP requirements, samples consisting of distinct layers of materials were analyzed and reported separately by the laboratory.

A summary of the homogenous materials is presented in Table 1. The laboratory analytical report and chain of custody form are included in Appendix 1.

EQI Project No. 11576.2 4

TABLE 1

Homogeneous Material Summary

Homogenous Material ACM1 (Y/N) Location Sample

ID

Friable (Y/N)

Est Qty (ACM) (ft2) Condition2

Multi-layered roofing material (shingle/tar/felt/insulation) N Main roof

11576.2-01 11576.2-02 11576.2-03

N -- G

Multi-layered roofing material (shingle/tar/felt/insulation) N Upper roof

11576.2-04 11576.2-05 11576.2-06

N -- G

Gray caulking N 2nd floor, window frames 11576.2-07 11576.2-08 11576.2-09

N -- G

Tan coating N 2nd floor, floor 11576.2-10 11576.2-11 11576.2-12

N -- G

Plaster N 2nd floor, exterior wall 11576.2-13 11576.2-14 11576.2-15

N -- G

Gypsum walls N 2nd floor, partition walls 11576.2-16 11576.2-17 11576.2-18

N -- G

Gray sealant N 2nd floor, fan coil unit (FCU) #4 11576.2-19 11576.2-20 11576.2-21

N -- G

Paper foil wrap over yellow fiberglass insulation N 1st floor, Collection Room, pipe system

(runs, elbows and tees)

11576.2-22 11576.2-23 11576.2-24

N -- G

Gray sealant N 1st floor, wall 11576.2-25 11576.2-26 11576.2-27

N -- G

Brown mastic N 1st floor, concrete ceiling 11576.2-28 11576.2-29 11576.2-30

N -- G

Paper foil wrap over yellow fiberglass insulation N 1st floor, Exhibit/Education office, pipe system (runs, elbows and tees)

11576.2-31 11576.2-32 11576.2-33

N -- G

1. ACM=>1% asbestos content

2. Good (G); Damaged (D) <10% distributed or 25% localized; Significant Damage (SD), >10% distributed or 25% localized

EQI Project No. 11576.2 5

TABLE 1

Homogeneous Material Summary

Homogenous Material ACM1 (Y/N) Location Sample

ID

Friable (Y/N)

Est Qty (ACM) (ft2) Condition2

Gypsum board N 1st floor office (below the Gallery), ceiling

216-01A 216-02A 216-03A

N -- G

EQI Project No. 11576.2 6

3.0 LEAD

Ten paint chip samples were collected from painted or coated materials that may be disturbed by the planned replacement of existing HVAC system.

3.1 Methodology

Prior to sampling, EQI visually surveyed the project areas for painted building components. Our sampling methodology generally followed the “Guidelines for the Evaluation and Control of Lead-Based Paint Hazard in Housing” published by the Department of Housing and Urban Development (HUD) in 1995.

The bulk samples were collected using a hand chisel and then placed into individual plastic bags which were sealed and labeled. The samples were then placed into another sealed bag for storage. Sampling equipment was cleaned between each sampling to avoid cross-contamination between samples.

Samples were submitted to Forensic Analytical in Rancho Dominguez, California. The samples were analyzed in accordance with EPA Method 3050B/7000B Lead, Flame Atomic Absorption Spectrophotometry. Forensic Analytical is accredited for lead analysis through successful participation in the American Industrial Hygiene Association’s (AIHA) Environmental Lead Laboratory Accreditation Program (ELLAP).

3.2 Results

Based on the laboratory analytical report, 1 of the 9 samples exceeded the EPA threshold of 0.5% lead by weight. The EPA defines lead-based paint as paint or other coatings containing lead equal to, or in excess of, 0.5 percent lead by weight. Note that paint with measurable amounts of lead below the EPA threshold was also identified in other paint/coatings.

A summary of lead paint is presented in Table 2. The laboratory analytical report and chain of custody form are included in Appendix 2.

EQI Project No. 11576.2 7

TABLE 2

Lead Paint Summary

Paint Color Int/Ext LBP1 (Y/N)

LCP2

(Y/N) Paint Location Sample ID Condition3,4

Tan Ext N Y 2nd floor, plaster wall 11576.2-01L Intact Tan Ext N N 2nd floor, floor 11576.2-02L Intact

White Int N N 2nd floor, partition gypsum walls 11576.2-03L Intact Black Int N N 2nd floor, metal ceiling 11576.2-04L Intact Beige Int N N 1st floor, Collection room, concrete wall 11576.2-05L Intact Gray Int N Y 1st floor, Collection room, concrete wall 11576.2-06L Intact Gray Int N Y 1st floor, Collection room, concrete ceiling 11576.2-07L Intact Beige Int Y N 1st floor, concrete ceiling 11576.2-08L Intact

Off-white Int N Y 1st floor, Exhibit/Education office, CMU wall 11576.2-09L Intact Off-white Int N N 1st floor, office (directly below the Gallery) 216-01L

1. LBP = >0.5% lead by weight

2. LCP = >laboratory detection limit but <0.5%

3. Exterior: Intact – Entire surface is intact; Fair - < 10ft2; Poor - >10 ft2

4. Interior: Intact – Entire surface is intact; Fair - < 2ft2 or < 10%; Poor - >2 ft2 or >10%

EQI Project No. 11576.2 8

4.0 ARSENIC

One composite sample from suspect homogeneous arsenic-containing roofing insulation was collected the roof

4.1 Methodology

Prior to sampling, EQI visually surveyed the roofing material for suspect arsenic-containing materials. EQI collected the sample from the following material:

• Roofing brown/tan insulation layer

Composite sampling strategy was utilized to determine the arsenic concentration in the insulation. The sample consisted of three random subsamples from the roof.

4.2 Results

The sample was submitted to Forensic Analytical, in Hayward, California for analysis using Atomic Absorption Spectroscopy, Flame in accordance with EPA Method ICP, 3050B/6010B.

Based on the laboratory analytical laboratory report, the insulation was not identified as an arsenic containing material. The laboratory analytical report and chain of custody forms are included in Appendix 3.

TABLE 3

Arsenic Sample Summary

Sample ID Arsenic (Y/N) Material Description Material Location

110917-01A N Brown/tan fibrous insulation Roof

EQI Project No. 11576.2 9

5.0 SUMMARY

5.1 Asbestos

Asbestos containing materials were not identified in this inspection. The NESHAP, 40 CFR 61 Part M, defines asbestos containing materials as those which contain greater than 1% asbestos.

5.2 Lead

Based on the laboratory analytical results from this inspection, the listed building component was painted or coated with lead-based paint (LBP).

Color Location Condition

Beige Concrete ceiling Intact

EPA defines lead-based paint as paint or other coatings containing lead equal to, or in excess of, 0.5% by weight. Lead at concentrations below the EPA guideline was also detected in other paint/coatings (see Table 2). The contractor’s employees removing or disturbing the painted material also must be informed that it contains lead and must have received training under OSHA 29 CFR 1926.62 Lead.

If the painted components containing the lead are scheduled for demolition, composite samples of the expected building waste generated should be collected for TCLP analysis to determine the waste disposal characterization. Hawaii Administrative Rules, Title 11, Department of Health, Chapter 261, Hazardous Waste Management allows a maximum concentration of lead contaminant by TCLP at 5.0 mg/L. TCLP results for lead exceeding the 5.0 mg/L threshold requires the material to be disposed of as hazardous waste. Results below this threshold allow for the materials to be disposed of as construction debris.

5.3 Arsenic

Arsenic containing materials were not identified in this inspection.

EQI Project No. 11576.2 10

6.0 LIMITATIONS

The information set forth is based solely on the agreed upon scope of services, on personal observation, laboratory data, and information provided by Nagamine Okawa Engineers, Inc.

Although this inspection provides information on the relative presence or absence of asbestos-containing materials, lead-based paint and arsenic containing materials, it should not be construed as a final statement that all hazardous materials have been identified.

Given the often obscure and elusive nature of hazardous materials, it is never possible to absolutely dismiss the possibility of additional hazardous materials. EnviroQuest, Inc. expressly disclaims any and all liability, representations, expressed or implied, contained in, or for omission from this report, or any other written or oral communication which might be interpreted as establishing the total extent of all liability present at the subject property.

Our services have been performed with usual thoroughness and competence of the consulting profession, in accordance with the standard of professional services at this time. No other warranty or representation, either expressed or implied is included or intended.

Any question regarding our work and this report, the presentation of the information, and the interpretation of the data are welcome and should be referred to the undersigned. EQI greatly appreciates this opportunity to assist you with your industrial hygiene needs. We look forward to working with you again in the future.

David Leigh Manager/CIH

Appendix 1

Asbestos Laboratory Analytical Report/

Chain-of-Custody Form

Final Report

(EPA Method 600/M4-82-020 and 600/R-93-116, Visual Area Estimation)

Bulk Asbestos Analysis 7104Client ID:EnviroQuest, Inc.

B249460Report Number:Steve Tanaka

Date Received:98-029 Hekaha Street 11/16/17Date Analyzed:Suite 21 11/17/17Date Printed:Aiea, HI 96701

First Reported:

710411576.2; USACE HVAC System, Museum Ft. DeRussy FALI Job ID:Job ID/Site:

Date(s) Collected: 11/09/2017 33Total Samples Submitted:

Total Samples Analyzed: 33

11/14/17

11/17/17

Sample ID Lab Number Asbestos

Type Percent in

Layer Asbestos AsbestosPercent in Percent in

Type TypeLayer Layer

11576.2-01 51102832 Layer: Grey Roof Shingle ND Layer: Black Semi-Fibrous Tar ND Layer: Grey Roof Shingle ND Layer: Black Semi-Fibrous Tar ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (Trace) Fibrous Glass (10 %) Synthetic (15 %)

11576.2-02 51102833 Layer: Grey Roof Shingle ND Layer: Black Semi-Fibrous Tar ND Layer: Grey Roof Shingle ND Layer: Black Semi-Fibrous Tars ND Layer: Black Felts ND Layer: Brown Fibrous Material ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (5 %) Fibrous Glass (15 %) Synthetic (15 %)

11576.2-03 51102834 Layer: Grey Roof Shingle ND Layer: Black Semi-Fibrous Tar ND Layer: Brown Fibrous Material ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (20 %) Fibrous Glass (10 %) Synthetic (15 %)

11576.2-04 51102835 Layer: Grey Roof Shingle ND Layer: Black Semi-Fibrous Tar ND Layer: Black Felt ND Layer: Wood ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (10 %) Fibrous Glass (15 %) Synthetic (20 %)

2959 Pacific Commerce Drive, Rancho Dominguez, CA 90221 / Telephone: (310) 763-2374 (888) 813-9417 / Fax: (310) 763-8684

Report Number: B249460 Date Printed: 11/17/17Client Name: EnviroQuest, Inc.

Sample ID Lab Number Asbestos

Type Percent in

Layer Asbestos AsbestosPercent in Percent in

Type TypeLayer Layer

11576.2-05 51102836 Layer: Grey Roof Shingle ND Layer: Black Tar ND Layer: Black Felt ND Layer: Grey Roof Shingle ND Layer: Black Felt ND Layer: Tan Fibrous Material ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (10 %) Fibrous Glass (15 %) Synthetic (15 %)

11576.2-06 51102837 Layer: Grey Roof Shingle ND Layer: Black Felt ND Layer: Grey Roof Shingle ND Layer: Black Felt ND Layer: Tan Fibrous Material ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (10 %) Fibrous Glass (25 %) Synthetic (10 %)

11576.2-07 51102838 Layer: Grey Non-Fibrous Material ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (Trace)

11576.2-08 51102839 Layer: Tan Non-Fibrous Material ND Layer: Grey Non-Fibrous Material ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (Trace)

11576.2-09 51102840 Layer: White Drywall ND Layer: Grey Non-Fibrous Material ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (Trace)

11576.2-10 51102841 Layer: Off-White Plaster ND Layer: Grey Non-Fibrous Material ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (Trace)

2959 Pacific Commerce Drive, Rancho Dominguez, CA 90221 / Telephone: (310) 763-2374 (888) 813-9417 / Fax: (310) 763-8684

Sample ID Lab Number Asbestos

Type Percent in

Layer Asbestos AsbestosPercent in Percent in

Type TypeLayer Layer

11576.2-11 51102842 Layer: Off-White Plaster ND Layer: Beige Non-Fibrous Material ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (Trace)

11576.2-12 51102843 Layer: Off-White Non-Fibrous Material ND Layer: Beige Non-Fibrous Material ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (Trace)

11576.2-13 51102844 Layer: Grey Plaster ND Layer: Paint ND Layer: Tan Plaster ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (Trace)

11576.2-14 51102845 Layer: Grey Plaster ND Layer: Paint ND Layer: Tan Plaster ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (Trace)

11576.2-15 51102846 Layer: Grey Plaster ND Layer: Paint ND Layer: Tan Plaster ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (Trace)

11576.2-16 51102847 Layer: White Drywall ND Layer: White Skimcoat/Joint Compound ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (15 %) Fibrous Glass (3 %)

11576.2-17 51102848 Layer: White Drywall ND Layer: White Skimcoat/Joint Compound ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (15 %) Fibrous Glass (Trace)

2959 Pacific Commerce Drive, Rancho Dominguez, CA 90221 / Telephone: (310) 763-2374 (888) 813-9417 / Fax: (310) 763-8684

Sample ID Lab Number Asbestos

Type Percent in

Layer Asbestos AsbestosPercent in Percent in

Type TypeLayer Layer

11576.2-18 51102849 Layer: White Drywall ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (10 %) Fibrous Glass (3 %)

11576.2-19 51102850 Layer: Grey Non-Fibrous Material ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (Trace)

11576.2-20 51102851 Layer: Grey Non-Fibrous Material ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (Trace)

11576.2-21 51102852 Layer: Grey Non-Fibrous Material ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (Trace)

11576.2-22 51102853 Layer: Yellow Fibrous Material ND Layer: Tan Fibrous Material with Foil ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (10 %) Fibrous Glass (75 %)

11576.2-23 51102854 Layer: Yellow Fibrous Material ND Layer: Tan Fibrous Material with Foil ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (10 %) Fibrous Glass (75 %)

11576.2-24 51102855 Layer: Yellow Fibrous Material ND Layer: Tan Fibrous Material with Foil ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (10 %) Fibrous Glass (75 %)

11576.2-25 51102856 Layer: White Foam ND Layer: Off-White Non-Fibrous Material ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (Trace)

2959 Pacific Commerce Drive, Rancho Dominguez, CA 90221 / Telephone: (310) 763-2374 (888) 813-9417 / Fax: (310) 763-8684

Sample ID Lab Number Asbestos

Type Percent in

Layer Asbestos AsbestosPercent in Percent in

Type TypeLayer Layer

11576.2-26 51102857 Layer: White Foam ND Layer: Off-White Non-Fibrous Material ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (Trace)

11576.2-27 51102858 Layer: White Foam ND Layer: Off-White Non-Fibrous Material ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (Trace)

11576.2-28 51102859 Layer: Brown Mastic ND Layer: Paint/Coating ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (3 %)

11576.2-29 51102860 Layer: Brown Mastic ND Layer: Paint/Coating ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (3 %)

11576.2-30 51102861 Layer: Brown Mastic ND Layer: Paint/Coating ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (3 %)

11576.2-31 51102862 Layer: Yellow Fibrous Material ND Layer: Tan Fibrous Material with Foil ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (10 %) Fibrous Glass (75 %)

11576.2-32 51102863 Layer: Yellow Fibrous Material ND Layer: Tan Fibrous Material with Foil ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (10 %) Fibrous Glass (75 %)

2959 Pacific Commerce Drive, Rancho Dominguez, CA 90221 / Telephone: (310) 763-2374 (888) 813-9417 / Fax: (310) 763-8684

Sample ID Lab Number Asbestos

Type Percent in

Layer Asbestos AsbestosPercent in Percent in

Type TypeLayer Layer

11576.2-33 51102864 Layer: Yellow Fibrous Material ND Layer: Tan Fibrous Material with Foil ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (10 %) Fibrous Glass (75 %)

Analytical results and reports are generated by Forensic Analytical Laboratories Inc. (FALI) at the request of and for the exclusive use of the person or entity (client) named on such report. Results, reports or copies of same will not be released by FALI to any third party without prior written request from client. This report applies only to the sample(s) tested.

Supporting laboratory documentation is available upon request. This report must not be reproduced except in full, unless approved by FALI. The client is solely responsible for the use and interpretation of test results and reports requested from FALI. Forensic Analytical Laboratories Inc. is not able to assess the degree of hazard resulting from materials analyzed. FALI reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified. All samples were received in acceptable condition unless otherwise noted.

Note: Limit of Quantification ('LOQ') = 1%. 'Trace' denotes the presence of asbestos below the LOQ. 'ND' = 'None Detected'.

Tiffani Ludd, Laboratory Supervisor, Rancho Dominguez Laboratory

2959 Pacific Commerce Drive, Rancho Dominguez, CA 90221 / Telephone: (310) 763-2374 (888) 813-9417 / Fax: (310) 763-8684

EnviroQuest PLM DATA SHEET kM'j! .tiZProiect Name: Project No.:. Date: l \ O C | | g

J _ o f A Page:.

Material Description:

5 ^

Friabte

Non-friable

Sample No. Location % Asb. Asb. Type j\.CH/.J - 0 1

4?

CONDITION: % Damaaed: 1 Localized: % Distributed: Total Material Quantity:

Surfacing Material TSI

• Sig Damage

• Damaged

• Good Cond.

MISC.

• Sig, Damage

• Damaged

• Good Cond

% Crumbling -

% Delaminating -

% HzO/Gouges -

• Sig Damage

• Damaged

• Good Cond.

% Gouge/Punct -

% Crushed -

% H;0 Stains -

% Crumbling -

% Delaminating -

% H;0/Gouges-

Contact Potential • High • Moderate • Low

Vibration Potential • High • Moderate Low

Air Erosion

OVERALL POTENTIAL RATING

• High

• Significant Damage

• Moderate

• Damage

• Low

• Minimal Damage

Material Description: Qjifl^^rhA P€&r M ^4t^l4.<^ ^ l ^ T c O i y

Sample No. " ' " Location ' \\ii;$3^^^^%y^

Friable

Non-friable

% Asb, Asb. Type

CONDITION: b Damaged: % Localized: % Distributed: Total Material Quantity:

Surfacing Material TSI Misc.

a Sig, Damage . % Crumbling - • Sig, Damage % Gouge/Punct - • Sig, Damage % Crumbling -a Damaged % Delaminating - • Damaged % Crushed - • Damaged % Delaminating -a Good Cond % H20/Gouqes - n Good Cond. % HiO Stains - • Good Cond % HjO/Gouges-

Contact Potential • High • Moderate • Low

Vibration Potential • High • Moderate • Low

• .Low Air Erosion • High • Moderate

Surfacing <1,000 ff'= 3 Samples 1,000-5,000 ft^ = 5 Samples >5,000 fl^ = 7 Samples •

TSI Minimum of 3 Samples (Run) UNLESS • <6 In. or fr' = 1 Sample Minimum of 3 Samples (Elbow.S. T )

Misc. Minimum of 3 Samples {Hawaii)

Surfacing Sig. Damage = > fO% Dist. or 25% Local Damaged = < f 0% Dist. or 25% Local Good = Very Limited Damage

TSI

Sig. Damage = f 0% Missing Jacket OR

> 10% Dist. or 25%, Local Damaged = < f 0% Missing Jacket OR

< 10% Dist. or 25% Local Good = Very Limited Damage

Misc Sig, Damage = > fO% Dist. or25% Local Damaged = <10% Dist. or 25% Local Good - Very Limited Damage

98-029 Hekaha Street.-Suite 21, Aiea, HI 96701 Phone: (808) 486-5881 Fax: (808) 486-5889 E-mail: eqi@enviroquestinc.com

EnviroQuest , ^ ^ i ^ . . ^ HifA- n i.

Project No.: | | v ^ - K ; ^ 4 ' Project Name: L f e A ^ H V i / y i^j/JfyjA^

PLM DATA

Date:

Material Description:

Friable

Non-friable

Sample No Location

CONDITION: % Distributed Total Material Quantity:

Surfacing Material

• Sig, Damage n Damaged

• Good Cond.

'o Crumbling - 'o Delaminating - 'A H;0/Gouges -

• Sig. Damage

• Damaged

• Good Cond-

GOuge/PunCi - % Crushed -

% H;0 Stains -

O Sig Damage D Damaged

• Good Cond.

% Crufnbling -ti Delaminating - % H;0/GQuges-

Contact Potential • High Vibration Potential • High

High

OVERALL POTENTIAL RATING • Significant Damage • Minimal Damage

Material Description: TQLIA ^P\J^ CQ^H^W^ Friable

Non-friable

Sample No.. Location

XL

Total Material Quai mtlty:

Surfacing Material

• Sig. Damage

• Damaged

• Good Cond.

• Sig. Damage

• Damaged

• Good Cond.

'o Crumbling -a Delaminating - A HzQ/Gouges -

• Sig. Damage

• Damaged

• Good Cond.

Vo Gouge/Punct - % Crushed -

% HzO Stains -

% Crumbling - % Delaminating - % HjO/Geuges-

Contact Potential • High • Moderate • Low Vibration Potential _High_ • Moderate

• Moderate

High

OVERALL POTENTIAL RATING It Damage Damage li Damage

Material Description:

Friable

Non-friable

Sample No. Location

\l Material Quantity: % Damaged:

Surfacing Material O Sig. Damage

• Damaged

• Good Cond.

• Sig, Damage

• Damaged

• Good Cond.

% Crumbling - 'a Delaminating - A H;0/GQuge5 -

• Sig. Damage

• Damaged

• Good Cond.

% Gouge/Punct - % Crushed -

%H;0 Stains-

% Crumbling - % Delaminating - % H;0/GQuges-

Contact Potential High • Low Vibration Potential Hiflh_

_High • Moderate

• Damage

• Low

OVERALL POTENTIAL RATING Significant Damage

98-029 Hekaha Street, Suite 21, Aiea, HI 96701 Phone: (808) 486-5881 Fax: (808) 486-5889 E-mail: eqi@enviroquestinc.com 8-10-4-201 Sagamiono, Minami-ku, Sagamihara-shi, Kanagawa-ken 252-0303 Phone: (042) 851-5675

EnviroQuest

Project No.: j j C - ^ ' .tiy Project Name: Date:

Î SJSS/ Page: of

Material Description: M^Ct ( ^ V V C N k r l l ^{ ^ C U P ^ H d N o ' n S i e

Sample No. ^ ' ' ' Location

CONDITION: % Dama 3ed: % Localized: % Distributed: | Total Material Quantity:

Surfacing M atatiai TSI Misc.

• Sig- Damage % Crumbling -

• Damaged % Delaminating ^

• Good Cond. %H,0/Gouges-

• Sig. Damage % Gouge/Punct-

• Damaged % Crushed •

• Good Cond. %H,0 Stains-

• Sig. Damage % Crumbling-

• Damaged % Delaminating -

• Good Cond. % H,0/Gouqes-

Gontact Potential • High • Moderate • Low

\/lKAitlnrt DAtBntiil i-li/rh 1̂ iLjInHarata 1 ^ 1 rwn viDraiion poisniiai L J riign L J MOueraie L J LOW

Air Erosion • High • Moderate • Low

OVERALL POTENTIAL RATING • Significant Damage • Damage • Minimal Damage

Material Description: Qjfi^ £M\<^IM/VY Friable

Non-frlable

Sample No Location

1 ^

I Total Material Quantity: CONDITION; % Damaged:

Surfacing Material

• Sig. Damage

• Damaged

• Good Cond.

• Sig. Damage n Damaged

• Good Cond.

% Crumbling - % Delaminating - % H:0/Gouges •

• Sig. Damage

• Damaged

• Good Cond-

% Gouge/Punct- % Crushed -

% H;0 Stains -

% Crumbling - % Delaminating - % H^O/Gouges-

Contact Potential _n_Hifln_ •

Vibration Polential

.D_tJi2t

• Significant Damage

• Moderate

• Damage OVERALL POTENTIAL RATING Minimal Damage

Material Description:

QomnlQ Mn I \n til A ll / ' > A t i \ ^

Friable

Non-friable

Sample No.

-4 I -4

I Total Material Quantity:

Surfacing Material

• Sig. Damage

• Damaged

• Good Cond.

• Sig. Damage

• Damaged

• Good Cond-

• Sig. Damage

• Damaged

• Good Cond

% Crumbling - % Delaminating - % HjO/Gouges -

• Moderate

• Moderate

% Gouge/Punct - % Crushed -

% Ĥ O Stains •

% Crumbling - % Delaminating - % HzO/Gouges-

Contact Potential Vibration Potential _ g _ H i f l h _

• Significant Damage

• Moderate • Low

• Minim OVERALL POTENTIAL RATING ^ a m a g ^

98-029 Hekaha Street, Suite 21, Aiea, HI 96701 Phone: (808) 486-5881 Fax: (808) 486-5889 E-mail: eqi@enviroquestlnc.com

EnviroQuest

Project No.:_ l^r?^iZ Prelect N a n < ^ S . A ^ \}^(^0 ^ QjL^mi

PLM DA

Material Description:

Date: • r

Page: ^ of 4"

Friable

Non-friable

Sample No. ition

I Total Material Quantity:

Surfacing Material P Sig. Damage

• Damaged

• Good Cond.

• Sig. Damage D Damaged

• Good Cond.

i, Crumbling - % Delaminating - % HsOAjQuges -n High

• Sig. Damage

• Damaged

• Good Cond-

% Gouge/Punct - % C rustled -

% H2O Stains -

• Low

% Crumbling - % Delaminating - % HjO/Gouges-

Contact Potential g High Vibration Potential

• High

D Moderate

• Moderate

OVERALL POTENTIAL RATING ^ignificarv^amag^ Damage • Minimal Damage

Material Description:

Friable

Non-friabie

Sample No. Location

CONDITION: % Damaged: % Localized: % Distributed: Total Material Quantity:

Surfacing Material

• Sig. Damage

• Damaged

• Good Cond.

• Sig. Damage

• Damaged

• Good Cond.

% Crumbling - % Delaminating - % HjO/Gouges -

% Gouge/Punct - % Crushed -

% H;0 Stains -

• Sig, Damage

• Damaged

• Good Cond

% Crumbling - % Delaminating - % H^Q/GQugeS-

Contact Potential • High

• High

• Low Vitiralion Potential • Low

High •

"5" OVERALL POTENTIAL RATING • Significant Damage • Damage II^Damag^

Material Description:

Sample No. | ^ Locatiofi V̂ L&0[̂ (Wv̂ ^̂ 1

Friable

Non-friable xX i Total Materiel Quantity:" % Damaged:

Surfacing Material

• Sig. Damage

• Damaged

• Good cond

• Sig. Damage

• Damaged

• Good Cofxt.

% Crumbling - % Delaminating - % H;O/G0uQeS -

• Sig. Damage

• Damaged

• Good Cond.

% Gouge/Punct - % Crushed -

%HjO Stains -

% Crumbling • % Delaminating - % H^Q/Gouges-

Contact Potential • .High

Vibration Potential • High • Low High • Low

• Minimal Damage OVERALL POTENTIAL RATING Sign! Damage Damage

98-029 Hekaha Street, Suite 21, Aiea, HI 96701 Phone: (808) 486-5881 Fax: (808)486-5889 E-mail: eqi@enviroquestinc.eom

Final Report

(EPA Method 600/M4-82-020 and 600/R-93-116, Visual Area Estimation)

Bulk Asbestos Analysis 7104Client ID:EnviroQuest, Inc.

B254057Report Number:Steve Tanaka

Date Received:98-029 Hekaha Street 02/22/18Date Analyzed:Suite 21 02/22/18Date Printed:Aiea, HI 96701

First Reported:

710411576.2; Army Museum, Fort DeRussy FALI Job ID:Job ID/Site:

Date(s) Collected: 02/16/2018 3Total Samples Submitted:

Total Samples Analyzed: 3

02/20/18

02/22/18

Sample ID Lab Number Asbestos

Type Percent in

Layer Asbestos AsbestosPercent in Percent in

Type TypeLayer Layer

216-01A 51121078 Layer: White Drywall ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (10 %) Fibrous Glass (2 %)

216-02A 51121079 Layer: White Drywall ND Layer: Off-White Skimcoat/Joint Compound ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (15 %) Fibrous Glass (2 %)

216-03A 51121080 Layer: White Drywall ND Layer: Drywall Tape ND Layer: Off-White Skimcoat/Joint Compounds ND Layer: Paint ND

Asbestos (ND)Total Composite Values of Fibrous Components:

Cellulose (15 %) Fibrous Glass (2 %)

Analytical results and reports are generated by Forensic Analytical Laboratories Inc. (FALI) at the request of and for the exclusive use of the person or entity (client) named on such report. Results, reports or copies of same will not be released by FALI to any third party without prior written request from client. This report applies only to the sample(s) tested.

Supporting laboratory documentation is available upon request. This report must not be reproduced except in full, unless approved by FALI. The client is solely responsible for the use and interpretation of test results and reports requested from FALI. Forensic Analytical Laboratories Inc. is not able to assess the degree of hazard resulting from materials analyzed. FALI reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified. All samples were received in acceptable condition unless otherwise noted.

Note: Limit of Quantification ('LOQ') = 1%. 'Trace' denotes the presence of asbestos below the LOQ. 'ND' = 'None Detected'.

Tiffani Ludd, Laboratory Supervisor, Rancho Dominguez Laboratory

2959 Pacific Commerce Drive, Rancho Dominguez, CA 90221 / Telephone: (310) 763-2374 (888) 813-9417 / Fax: (310) 763-8684

EnviroQuest PLM DATA SHEET

Project No.: Project Name:. Date: 2/>l^//^

Page:_ ' o f ' l lJir ffilir--. ti/>ixfg^ Material Description:

Eijabie oR-frtable

Sample No. .ocation % Asb. Type

CONDITION: % Damagad: % Localized: % Distributed: Total Material Quantity:

Surfacing Material TSI

• Sig Damage

• Damaged fja' Good Cord.

Misc.

• Sig. Damage

• Damaged

• Good Cond.

% Crumbling - % Delaminating - % HaO/Gouges -

• Sig Damage

• Damaged

• Good Cond.

a Gouge/Punct - % Crustied -

% H2O Stains -

% Crumbling - % Delaminating - % HzO/Gouges-

Contact Potential • • Moderate D ^ L o w ^Low

Vibration Potential Hiah_ • Moderate Air Erosion • High

• Significant Damage

• Moderate Low

OVERALL POTENTIAL RATING • Damage Minimal Damage

Material Description:

Friable

Non-friable

Sample No. Location %Asb. Asb. Type

CONDITION: % Damaged: % Localized: % Distributed: 1 Total Material Quantity:

Surfacing Material TSI Misc.

• Sig. Damage % Crumbling • Sig. Damage % Gouge/Punct - • Sig. Damage ; % Crumbling -

• Damaged % Delaminating • Damaged , > J % Crushed - • Damaged % Delaminating -

• Good Cond. % HjO/Gouges • Good Cond. < % H2O Stains - • Good Cond, % HjO/Gouges-

Contact Potential • Higti • Moderate • Low

Vibration Potential • Hiqti • Moderate n Low

Air Erosion • High • Moderate • Low

OVERALL POTENTIAL RATING • Significant Damage • >f • Damage • Minimal Damage

Sampled By: 1̂ £ajPn<ll DOH Cert No:

Delivered to Lab By:

d By/Date/Time: Relinquished By/Date/Time:

Relinquished By/Date/Time:

TURNAROUND TIME: • < 12 Hou • 24 Hours • 3 Days • 5 Days iŴ i

Surfacing <1,000ft^ = 3 Samples 1,000-5,000 ft^ = 5 Samples >5,000 fl''= 7 Samples •

TSI Minimum of 3 Samples (Run) UNLESS <6 In. orft'^= 1 Sample Minimum of 3 Samples (Elbow & T )

Misc. Minimum of 3 Samples (Hawaii)

Surfacing Sig: Damage = > 10% Dist. or 25% Local Damaged = < 10%, Dist. or 25% Local Good - Very Limited Damage

TSI

Sig. Damage = 10%, Missing Jacket OR

> 10% Dist. or 25%, Local Damaged = <10% Missing Jacket OR

< 10% Dist. or 25% Local Good = Very Limited Damage

Misc Sig. Damage = > fO% Dist. or 25% Local Damaged = <10%, Dist. or 25%, Local Good = Very Limited Damage

98-029 Hekaha Street, Suite 21, Alea, HI 96701 Phone: (808) 486-5881 Fax: (808) 486-5889 E-mail: eql@envlroquestlnc.com

Appendix B Appendix 2

Lead-Base Paint Summary Table

XRF Spectrographs

Lead

Metals Analysis of Paints Client ID:

Report Number:

Date Received:

M191603

Job ID / Site: 11576.2; USACE HVAC System Museum, part DeRussy

EnviroQuest, Inc.

Suite 21

FALI Job ID:

Date Analyzed:

Steve Tanaka

Aiea, HI 96701

98-029 Hekaha Street

Date Printed: 11/17/17 11/17/17

First Reported: 11/17/17

11/14/17

Final Report

Date(s) Collected: 11/09/17 Total Samples Submitted:

Total Samples Analyzed:

Sample Number Lab Number Result Result Reporting Method

Analyte Units Limit* Reference

EPA 3050B/7000B0.007Pb11576.2-01L LM148633 wt% 0.006

EPA 3050B/7000B< 0.006Pb11576.2-02L LM148634 wt% 0.006

EPA 3050B/7000B< 0.008Pb11576.2-03L LM148635 wt% 0.008

EPA 3050B/7000B< 0.007Pb11576.2-04L LM148636 wt% 0.007

EPA 3050B/7000B< 0.006Pb11576.2-05L LM148637 wt% 0.006

EPA 3050B/7000B0.35Pb11576.2-06L LM148638 wt% 0.02

EPA 3050B/7000B0.009Pb11576.2-07L LM148639 wt% 0.008

EPA 3050B/7000B18Pb11576.2-08L LM148640 wt% 2

EPA 3050B/7000B0.06Pb11576.2-09L LM148641 wt% 0.01

Analytical results and reports are generated by Forensic Analytical at the request of and for the exclusive use of the person or entity (client) named on such report. Results, reports or copies of same will not be released by Forensic Analytical to any third party without prior written request from client. This report applies only to the sample(s) tested. Supporting laboratory documentation is available upon request. This report must not be reproduced except in full, unless approved by Forensic Analytical. The client is solely responsible for the use and interpretation of test results and reports requested from Forensic Analytical. Forensic Analytical is not able to assess the degree of hazard resulting from materials analyzed. Forensic Analytical reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified. Any modifications that have been made to referenced test methods are documented in Forensic Analytical's Standard Operating Procedures Manual. Sample results have not been blank corrected. Quality control and sample receipt condition were acceptable unless otherwise noted.

Beatriz Hinojosa, Laboratory Supervisor, Rancho Dominguez Laboratory

* The Reporting Limit represents the lowest amount of analyte that the laboratory can confidently detect in the sample, and is not a regulatory level. The Units for the Reporting Limit are the same as the Units for the Final Results.

2959 Pacific Commerce Drive, Rancho Dominguez, CA 90221 / Telephone: (310) 763-2374 (888) 813-9417 / Fax: (310) 763-8684

Metals Analysis of Paints

Report Number:

Date Received:

M195169

Job ID / Site: 11576.2; Army Museum, Fort Derussy

EnviroQuest, Inc.

Suite 21

FALI Job ID:

Date Analyzed:

Steve Tanaka

Aiea, HI 96701

98-029 Hekaha Street

Date Printed: 02/22/18 02/22/18

First Reported: 02/22/18

02/20/18

Final Report

Date(s) Collected: 02/16/18 Total Samples Submitted:

Total Samples Analyzed:

Sample Number Lab Number Result Result Reporting Method

Analyte Units Limit* Reference

EPA 3050B/7000B< 0.006Pb216-01L LM151476 wt% 0.006

Analytical results and reports are generated by Forensic Analytical at the request of and for the exclusive use of the person or entity (client) named on such report. Results, reports or copies of same will not be released by Forensic Analytical to any third party without prior written request from client. This report applies only to the sample(s) tested. Supporting laboratory documentation is available upon request. This report must not be reproduced except in full, unless approved by Forensic Analytical. The client is solely responsible for the use and interpretation of test results and reports requested from Forensic Analytical. Forensic Analytical is not able to assess the degree of hazard resulting from materials analyzed. Forensic Analytical reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified. Any modifications that have been made to referenced test methods are documented in Forensic Analytical's Standard Operating Procedures Manual. Sample results have not been blank corrected. Quality control and sample receipt condition were acceptable unless otherwise noted.

Beatriz Hinojosa, Laboratory Supervisor, Rancho Dominguez Laboratory

* The Reporting Limit represents the lowest amount of analyte that the laboratory can confidently detect in the sample, and is not a regulatory level. The Units for the Reporting Limit are the same as the Units for the Final Results.

2959 Pacific Commerce Drive, Rancho Dominguez, CA 90221 / Telephone: (310) 763-2374 (888) 813-9417 / Fax: (310) 763-8684

E n viro

Q u e st

M

IS

C E

LLA

N

E O

U S

B

U

LK

D

A T

S H

E

T

P roject N am e:

Location:

P age:

fo rt

Pg T urnaround T im e

H rs

H rs fc>t8H rs

A nalysis:

•T C

L P

L e a d

•M ic ro

ID

(spore)

T

P L

P

R C p io ta i Lead

D ays

D s

D ays

S am pling M edia:

•B u lk

•T a p e

•S o il •V a c u u m

•S w a b

•W a te r

D ate:

P roject N o.:

jl jQ f

•o th e r:

•W ip e

S a m p le # B u ild in g

In t/

E xt

F ir.

R o o o m p o n e n t

S u b stra te C o lo r o f W a s te S tre a re a / V o l R esult

-1

-0

-1

-0

/ffw

'^alk" 7 c

Z

2 3 3 4 4 5

5 6 6

7 7

_eeceA red b S

/D s e

I g elinquished B y/D ate/T im e

R eceived B y/D ate/T im e

A nalyzed B y

D ate A nalyzed

S E

N D

LL

C

O f^R

E S

P O

N D

E N

F

X

808.486.5889

E -m a il:

eqi@ en viroquestinc.

com

-0

9 H e ka h a S tre e t, S uite 2

, A ie a , H

I 9

P h o n e

: (808) 4

-5

F ax: (808) 4

-5

E

-m ail: e q i@ e n viro q u e stin c.co

Appendix 3

Arsenic

Metals Analysis of Bulks - TTLC

Report Number:

Date Received:

M191593

Job ID / Site: 11576.2, Usace Hvac System NW Museum, Fort De Russy

EnviroQuest, Inc.

Suite 21

FALI Job ID:

Date Analyzed:

Steve Tanaka

Aiea, HI 96701

98-029 Hekaha Street

Date Printed: 11/21/17 11/15/17

First Reported: 11/15/17

11/14/17

Final Report

Date(s) Collected: 11/09/17 Total Samples Submitted:

Total Samples Analyzed:

Sample Number Lab Number Result Result Reporting Method

Analyte Units Limit* Reference

EPA 3050B/6010B< 4As110917-01A 30784642 mg/kg 4

Analytical results and reports are generated by Forensic Analytical at the request of and for the exclusive use of the person or entity (client) named on such report. Results, reports or copies of same will not be released by Forensic Analytical to any third party without prior written request from client. This report applies only to the sample(s) tested. Supporting laboratory documentation is available upon request. This report must not be reproduced except in full, unless approved by Forensic Analytical. The client is solely responsible for the use and interpretation of test results and reports requested from Forensic Analytical. Forensic Analytical is not able to assess the degree of hazard resulting from materials analyzed. Forensic Analytical reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified. Any modifications that have been made to referenced test methods are documented in Forensic Analytical's Standard Operating Procedures Manual. Sample results have not been blank corrected. Quality control and sample receipt condition were acceptable unless otherwise noted.

Daniele Siu, Laboratory Supervisor, Hayward Laboratory

* The Reporting Limit represents the lowest amount of analyte that the laboratory can confidently detect in the sample, and is not a regulatory level. The Units for the Reporting Limit are the same as the Units for the Final Results.

3777 Depot Road, Suite 409, Hayward, CA 94545 / Telephone: (510) 887-8828 (800) 827-FASI / Fax: (510) 887-4218