8fd9c5b7-db25-48ea-b074-b24f0103d9ab.pdf

P.O. Box 13216 Lansing, MI 48901 Phone: 888.449.4566 Fax: 888.448.8739 www.redcedarconsulting.net

December 11, 2024

Mr. Brian Taylor City of Jackson Community Development Department Jackson, MI 49202

RE: Asbestos Containing Material and Hazardous Materials Inspection 112 E Wilkins St. Jackson, MI 49203 Parcel ID: 5-020400000

Dear Mr. Taylor:

Red Cedar Consulting has completed an asbestos-containing material (ACM) and hazardous materials inspection at 112 E Wilkins St. Jackson, Michigan (Subject Property). This inspection was completed at the request of the City of Jackson to comply with the United States Environmental Protection Agency (USEPA) requirements for demolition and renovation set forth under the National Emissions Standards for Hazardous Air Pollutants (NESHAP, 40 CFR Part 61). This inspection was also completed to comply with the Occupational Safety and Health Administration (OSHA) Asbestos Standards for Construction (29 CFR 1926.1101) which limits employee exposure to asbestos.

SUBJECT PROPERTY

The Subject Property is comprised of a .08 acre residential parcel which contains an approximate 1,674 square foot residential building (the Building) constructed in 1910. The Building was constructed on a concrete basement with two aboveground floors. The exterior walls of the Building were finished with vinyl over wood lap while the roof was sealed with asphalt shingles. The Building can be further divided into a front porch, living room, dining room, kitchen, bath, and two bedrooms on the first floor while the second floor contains a living room, dining room, kitchen, bathroom and a bedroom.

VISUAL INSPECTION AND SAMPLING

Asbestos Containing Materials Inspection

Jeff Cain of Red Cedar Consulting (Red Cedar), accredited State Of Michigan/EPA Asbestos Building Inspector (Accreditation Number A14057) who completed training per the Michigan Asbestos Workers Accreditation Act 440, completed an inspection of the Subject Property on November 20, 2024 for suspected asbestos containing building materials.

Project No.: 12-1027

This inspection, and subsequent sample collection was completed in accordance with the USEPA Asbestos Hazard Emergency Response Act (AHERA) (40 CFR Part 763) assessment and sampling protocol.

During the completion of the inspection, each area of the Subject Property was visually inspected for asbestos containing building materials (ACBM). Following the completion of the visual inspection, Red Cedar staff identified each suspect area of friable and non-friable ACBM and sorted them into one of three homogenous categories for sampling purposes. AHERA defines friable as a material that when dry, may be crumbled, pulverized, or reduced to powder by hand pressure. A homogenous area is defined by OSHA as an area of surfacing, thermal system insulation (TSI) or miscellaneous material that is uniform in color and texture. Surfacing materials are most commonly found in sprayed-on, troweled-on or otherwise applied to surfaces, such as acoustical plaster on ceilings and fireproofing materials on structural members. TSI refers to materials applied to pipes, fittings, boilers, ductwork, or other components to prevent heat loss or gain, or condensation. Any material that does not fall under the surfacing or TSI category, such as floor tile, drywall, and acoustical ceiling tile are placed into the miscellaneous materials category.

Following the completion of the visual inspection, Red Cedar staff identified the following materials as suspect ACBM:

• Asphalt Shingle

• Tar Paper

• Window Trim Caulk

• Window Glazing

• Chimney Caulk

• Duct Paper

• Linoleum

• Vinyl

• 2’x4’ Ceiling Paper

• Drywall with Compound

• Shower Trim Caulk

• Plaster

Red Cedar staff collected forty-five samples of suspect ACBM separated into twenty distinct homogenous groups for laboratory analysis. Samples were collected and submitted to APEX Research Inc.

Laboratories (APEX) (Accreditation Number 102118-0) for laboratory analysis. Analysis was completed utilizing polarized light microscopy (PLM) which is the Environmental Protection Agency (EPA) approved method for analysis of bulk materials for asbestos. PLM analysis completed pursuant to method (EPA 600/M4-82-020) identifies asbestos fiber bundles by the visual properties displayed when the sample is treated with various dispersion staining liquids. The laboratory report completed following the sample analysis indicates if asbestos is present, and at what percentage along with a description and percentage of other fibrous and non-fibrous materials and sample color. Chain-of-custody documentation was followed from sample collection through shipping and receiving of the samples at the designated laboratory. The documentation assures that samples will meet the quality assurance/quality control measures defined by AHERA. The laboratory analytical report prepared by APEX for the forty-five samples is included as Attachment A.

Hazardous Materials Inspection

On November 20, 2024, the Subject Property was also inspected for the presence of hazardous materials which include but are not limited to polychlorinated biphenyls (PCBs) and potential mercury containing equipment and any items or containers that may contain or be classified as a hazardous or regulated material. Each material, if identified, was documented along with the approximate location. Any materials identified as hazardous are included in Table 1.

INSPECTION RESULTS AND RECOMMENDATIONS

During the completion of the asbestos inspection, forty-five samples of suspect ACM were collected and are documented in Table 2 along with the Red Cedar sample number, description, friability, material type, ACM classification, sample location, material quantity and laboratory analytical results. A Site Diagram was prepared which provides the general building layout and sample locations and is included as Attachment B.

ACM, as defined by the USEPA NESHAP is “any material containing more than 1 percent asbestos as determined using the method specified in appendix E, subpart E, 40 CFR part 763 Section 1, Polarized Light Microscopy”.

Friable ACM is defined by NESHAP as any material containing more than 1 percent asbestos that, when dry, can be crumbled, pulverized, or reduced to powder by hand pressure. Friable ACM is a concern due to the ease of unintentionally disturbing the ACM which may result in “visible emissions” which is known as a Fiber Release Episode.

Non-friable asbestos-containing material is defined as “material containing more than 1 percent asbestos that, when dry, cannot be crumbled, pulverized, or reduced to powder by hand pressure. Non-friable ACMs are separated into Category I and Category II ACM. Category I ACM is any asbestos containing packing’s, gaskets, resilient floor coverings (vinyl floor tile and linoleum are examples of these) and asphalt roofing products. Category II ACM is stated by NESHAP as any material excluding Category I non-friable ACM such as drywall, plaster or fiberboard insulation.

Presumed Asbestos Containing Material

Presumed Asbestos Containing Materials (PACM) are suspect surfacing, TSI and miscellaneous materials found in buildings constructed prior to 1980 which are classified as and due to the age of the structure, are assumed to be ACM and do not require sample collection and analysis. OSHA dictates that PACM may be “rebutted” following a complete inspection pursuant to AHERA protocol.

No PACM was identified during the completion of this inspection. All suspect materials identified were sampled and analyzed for ACM.

Table 3 lists the location, material description, friability, condition, material type (surfacing, thermal or miscellaneous) and approximate quantity of all PACM documented at the Subject Property.

Table 4 provides a summary of all ACM documented at the Subject Property which includes the material location, description, and approximate quantity.

Friable ACM’s

Duct Wrap identified in the building in conjunction with the forced air heating system is classified as friable ACM. The visual assessment to quantify the extent of this material identified HVAC Duct Wrap at the following locations within the basement, first and second floors:

• 2nd Fl. (1 register, 10 sq. ft. and vertical chase to basement, 25 sq. ft.)

• Basement (5 register boots, 2 sq. ft. each, 10 sq. ft.)

Category I ACM

One type of resilient floor covering (Vinyl Yellow Multilayer) located within the 2nd floor Dining Room was found to contain up to 2% Chrysotile asbestos. The assessment to quantify the extent of this material identified approximately 168 sq. ft. of this material within the Building.

Category II ACM

Chimney caulk samples, collected from the Basement were found to contain up to 10% asbestos following analysis. The assessment to quantify the extent of this material identified approximately 2 sq.

ft. of chimney caulk within the Building.

RECOMMENDATIONS

Asbestos Containing Materials

HVAC material identified in the Building system and listed below is classified as friable ACM and should be removed prior to any renovation/demolition activities.

• 2nd Fl. (1 register, 10 sq. ft. and vertical chase to basement, 25 sq. ft.)

• Basement (5 register boots, 2 sq. ft. each, 10 sq. ft.)

Chimney caulk identified on the interior of the Building must be abated prior to completion of any renovation/demolition activities at the Subject Property. Any Category II non-friable ACM that has a high probability of becoming or has become crumbled, pulverized, or reduced to powder by the forces expected to act on the material in the course of renovation or demolition operations must be properly abated.

The Category I resilient floor covering (Vinyl Yellow Multilayer) is a non-friable ACM that should be abated to mitigate any future exposure.

Please note: The location of samples obtained during this inspection were in a random fashion and areas that were not identified during this inspection may be damaged or have become damaged since the inspection was completed. If Category I or Category II friable materials are discovered prior to or during the demolition/renovation process, these materials must be abated prior to commencement of any demolition/renovation activities at the Subject Property.

Hazardous Materials

Hazardous Materials identified at the Subject Property and documented in Table 1 which require proper removal and disposal consist of the following items:

• No Hazardous Materials Identified

REGULATORY REQUIREMENTS

A Notification of intent to Renovate/Demolish form must be filed with the Michigan Department of Environmental Quality- Air Quality Division at least 10 working days prior to any renovation or demolition activities at a site.

The Notification of Intent to Renovate/Demolish form must also be completed and submitted to the MIOSHA-Asbestos Program whenever demolition, encapsulation and/or renovation activities at a site involving greater than ten lineal feet and/or fifteen square feet of ACM will be completed.

Regulated asbestos containing materials per NESHAP (40 CFR Part 61) which falls into any of the following categories are ACM’s that must be removed prior to any renovation/demolition activities at the Subject Property.

• Friable asbestos material.

• Category I non-friable ACM that has become friable.

• Category I non-friable ACM that will be or has been subjected to sanding, grinding, cutting, or abrading.

• Category II non-friable ACM that has a high probability of becoming or has become crumbled, pulverized, or reduced to powder by the forces expected to act on the material in the course of renovation or demolition operations.

Asbestos abatement should only be performed by a certified asbestos abatement contractor licensed to complete abatement work. The contractor must also follow the standards and requirements set forth per the OSHA Asbestos Standards for Construction (29 CFR 1926.1101) and the USEPA NESHAP (40 CFR Part 61).

Additional information regarding the OSHA Asbestos Standards for Construction (29 CFR 1926.1101) and the USEPA NESHAP (40 CFR Part 61) can be obtained by contacting the associated agency below.

NESHAP Asbestos Program MIOSHA-CSHD-Asbestos Program Department of Environmental Quality State of Michigan Phone: 517-284-6777 Phone: 517-284-7680 Email: asbestos@michigan.gov

DISCLAIMER

Red Cedar Consulting performed destructive testing methods in an attempt to access and inspect all areas of the Building. Unfortunately, due to the age of construction along with multiple additions/renovations that may have been completed on the Building, additional inspections may be required if suspect ACM material not documented within this report is encountered during renovation/demolition activities.

This report was prepared at the request and for exclusive use by the City of Jackson and may not be reproduced or sold without written permission from Red Cedar Consulting.

We appreciate the opportunity to provide the requested services. Please contact us at (888) 449-4566 with any questions or concerns.

Sincerely, Red Cedar Consulting

Aaron Paquet

Michigan/EPA Certified Asbestos Building Inspector (A30955)

©2024 Red Cedar Consulting, LLC.

Attachment A

APEX Research Laboratory Analytical Results

Certificate of Laboratory Analysis Test Method, Polarized Light Microscopy (PLM)

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 01 Asbestos Present: NO Fiberglass - 30%

Cust. #: WS-HM-01A No Asbestos Observed Other - 70% Material: Roofing M/L - Shingle Location:

Appearance: black,fibrous,nonhomogenous Layer: 1 of 4

Lab ID #: 114312 - 01a Asbestos Present: NO Fiberglass - 30% Cust. #: WS-HM-01A No Asbestos Observed Other - 70% Material: Shingle Location:

Appearance: black,fibrous,nonhomogenous Layer: 2 of 4

Lab ID #: 114312 - 01b Asbestos Present: NO Cellulose - 60% Cust. #: WS-HM-01A No Asbestos Observed Other - 40% Material: Felt Location:

Appearance: brown,fibrous,nonhomogenous Layer: 3 of 4

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. Liability limited to cost of analysis.

NVLAP Lab Code 102118-0

APEX Research Inc., 7717 Kensington Ct., Brighton, MI 48116

(734) 449-9990, Fax (734) 449-9991 Page 1 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 01c Asbestos Present: NO Fiberglass - 30%

Cust. #: WS-HM-01A No Asbestos Observed Other - 70% Material: Felt Location:

Appearance: black,fibrous,homogenous Layer: 4 of 4

Lab ID #: 114312 - 02 Asbestos Present: NO Fiberglass - 30% Cust. #: WS-HM-01B No Asbestos Observed Other - 70% Material: Roofing M/L - Shingle Location:

Appearance: black,fibrous,nonhomogenous Layer: 1 of 4

Lab ID #: 114312 - 02a Asbestos Present: NO Fiberglass - 30% Cust. #: WS-HM-01B No Asbestos Observed Other - 70% Material: Shingle Location:

Appearance: black,fibrous,nonhomogenous Layer: 2 of 4

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 2 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 02b Asbestos Present: NO Cellulose - 60%

Cust. #: WS-HM-01B No Asbestos Observed Other - 40% Material: Felt Location:

Appearance: black,fibrous,nonhomogenous Layer: 3 of 4

Lab ID #: 114312 - 02c Asbestos Present: NO Fiberglass - 30% Cust. #: WS-HM-01B No Asbestos Observed Other - 70% Material: Felt Location:

Appearance: black,fibrous,homogenous Layer: 4 of 4

Lab ID #: 114312 - 03 Asbestos Present: NO Cellulose - 60% Cust. #: WS-HM-02A No Asbestos Observed Other - 40% Material: Tar Paper Location:

Appearance: black,fibrous,homogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 3 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 04 Asbestos Present: NO Cellulose - 60%

Cust. #: WS-HM-02B No Asbestos Observed Other - 40% Material: Tar Paper Location:

Appearance: black,fibrous,homogenous Layer: 1 of 1

Lab ID #: 114312 - 05 Asbestos Present: NO Other - 100% Cust. #: WS-HM-03A No Asbestos Observed Material: Window Trim Caulk Location:

Appearance: beige,nonfibrous,homogenous Layer: 1 of 1

Lab ID #: 114312 - 06 Asbestos Present: NO Other - 100% Cust. #: WS-HM-03B No Asbestos Observed Material: Window Trim Caulk Location:

Appearance: beige,nonfibrous,homogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 4 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 07 Asbestos Present: NO Other - 100%

Cust. #: WS-HM-04A No Asbestos Observed Material: Window Glaze Location: Basement Appearance: beige,nonfibrous,homogenous Layer: 1 of 1

Lab ID #: 114312 - 08 Asbestos Present: NO Other - 100% Cust. #: WS-HM-04B No Asbestos Observed Material: Window Glaze Location: Basement Appearance: beige,nonfibrous,homogenous Layer: 1 of 1

Lab ID #: 114312 - 09 Asbestos Present: NO Other - 100% Cust. #: WS-HM-05A No Asbestos Observed Material: Window Glaze Location: 1st Floor Appearance: beige,nonfibrous,homogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 5 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 10 Asbestos Present: NO Other - 100%

Cust. #: WS-HM-05B No Asbestos Observed Material: Window Glaze Location: 1st Floor Appearance: beige,nonfibrous,homogenous Layer: 1 of 1

Lab ID #: 114312 - 11 Asbestos Present: NO Other - 100% Cust. #: WS-HM-06A No Asbestos Observed Material: Window Glaze Location: 2nd Floor Appearance: beige,nonfibrous,homogenous Layer: 1 of 1

Lab ID #: 114312 - 12 Asbestos Present: NO Other - 100% Cust. #: WS-HM-06B No Asbestos Observed Material: Window Glaze Location: 2nd Floor Appearance: beige,nonfibrous,homogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 6 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 13 Asbestos Present: YES Other - 90%

Cust. #: WS-HM-07A Chrysotile - 10% Material: Chimney Caulk Location: Basement Appearance: beige,fibrous,homogenous Layer: 1 of 1

Lab ID #: 114312 - 14 Asbestos Present:

Cust. #: WS-HM-07B Material: Chimney Caulk Location: Basement NOT ANALYZED Appearance:

Layer: 1 of 1

Lab ID #: 114312 - 15 Asbestos Present: YES Cellulose - 50% Cust. #: WS-HM-08A Chrysotile - 30% Other - 20% Material: Duct Paper Location:

Appearance: grey,fibrous,homogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 7 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 16 Asbestos Present:

Cust. #: WS-HM-08B Material: Duct Paper Location: NOT ANALYZED Appearance:

Layer: 1 of 1

Lab ID #: 114312 - 17 Asbestos Present: NO Cellulose - 40% Cust. #: WS-HM-09A No Asbestos Observed Other - 60% Material: Linoleum Location:

Appearance: beige,fibrous,nonhomogenous Layer: 1 of 1

Lab ID #: 114312 - 18 Asbestos Present: NO Cellulose - 40% Cust. #: WS-HM-09B No Asbestos Observed Other - 60% Material: Linoleum Location:

Appearance: beige,fibrous,nonhomogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 8 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 19 Asbestos Present: NO Cellulose - 10%

Cust. #: WS-HM-10A No Asbestos Observed Fiberglass - 5% Material: Vinyl Grey Other - 85% Location:

Appearance: beige,fibrous,nonhomogenous Layer: 1 of 1

Lab ID #: 114312 - 20 Asbestos Present: NO Cellulose - 10% Cust. #: WS-HM-10B No Asbestos Observed Fiberglass - 5% Material: Vinyl Grey Other - 85% Location:

Appearance: beige,fibrous,nonhomogenous Layer: 1 of 1

Lab ID #: 114312 - 21 Asbestos Present: NO Fiberglass - 5% Cust. #: WS-HM-11A No Asbestos Observed Other - 95% Material: Flooring Location:

Appearance: beige,fibrous,nonhomogenous Layer: 1 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 9 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 21a Asbestos Present: NO Cellulose - 10%

Cust. #: WS-HM-11A No Asbestos Observed Fiberglass - 5% Material: Linoleum Brown M/L Other - 85% Location:

Appearance: brown,fibrous,nonhomogenous Layer: 2 of 2

Lab ID #: 114312 - 22 Asbestos Present: NO Fiberglass - 5% Cust. #: WS-HM-11B No Asbestos Observed Other - 95% Material: Flooring Location:

Appearance: beige,fibrous,nonhomogenous Layer: 1 of 2

Lab ID #: 114312 - 22a Asbestos Present: NO Cellulose - 10% Cust. #: WS-HM-11B No Asbestos Observed Fiberglass - 5% Material: Linoleum Brown M/L Other - 85% Location:

Appearance: brown,fibrous,nonhomogenous Layer: 2 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 10 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 23 Asbestos Present: NO Cellulose - 5%

Cust. #: WS-HM-12A No Asbestos Observed Fiberglass - 5% Material: Linoleum Yellow Other - 90% Location:

Appearance: beige,fibrous,nonhomogenous Layer: 1 of 1

Lab ID #: 114312 - 24 Asbestos Present: NO Cellulose - 5% Cust. #: WS-HM-12B No Asbestos Observed Fiberglass - 5% Material: Linoleum Yellow Other - 90% Location:

Appearance: beige,fibrous,nonhomogenous Layer: 1 of 1

Lab ID #: 114312 - 25 Asbestos Present: NO Cellulose - 5% Cust. #: WS-HM-13A No Asbestos Observed Fiberglass - 5% Material: Brown Vinyl Wood Other - 90% Location:

Appearance: brown,fibrous,nonhomogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 11 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 26 Asbestos Present: NO Cellulose - 5%

Cust. #: WS-HM-13B No Asbestos Observed Fiberglass - 5% Material: Brown Vinyl Wood Other - 90% Location:

Appearance: brown,fibrous,nonhomogenous Layer: 1 of 1

Lab ID #: 114312 - 27 Asbestos Present: NO Cellulose - 40% Cust. #: WS-HM-14A No Asbestos Observed Mineral Wool - 30% Material: 2'x4' Drop Ceiling Tile Other - 30% Location:

Appearance: beige,fibrous,homogenous Layer: 1 of 1

Lab ID #: 114312 - 28 Asbestos Present: NO Cellulose - 40% Cust. #: WS-HM-14B No Asbestos Observed Mineral Wool - 30% Material: 2'x4' Drop Ceiling Tile Other - 30% Location:

Appearance: beige,fibrous,homogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 12 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 29 Asbestos Present: NO Cellulose - 20%

Cust. #: WS-HM-15A No Asbestos Observed Other - 80% Material: Drywall Location:

Appearance: white,fibrous,nonhomogenous Layer: 1 of 2

Lab ID #: 114312 - 29a Asbestos Present: NO Other - 100% Cust. #: WS-HM-15A No Asbestos Observed Material: Joint Compound Location:

Appearance: white,nonfibrous,homogenous Layer: 2 of 2

Lab ID #: 114312 - 30 Asbestos Present: NO Cellulose - 20% Cust. #: WS-HM-15B No Asbestos Observed Other - 80% Material: Drywall Location:

Appearance: white,fibrous,nonhomogenous Layer: 1 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 13 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 30a Asbestos Present: NO Other - 100%

Cust. #: WS-HM-15B No Asbestos Observed Material: Joint Compound Location:

Appearance: white,nonfibrous,homogenous Layer: 2 of 2

Lab ID #: 114312 - 31 Asbestos Present: NO Fiberglass - 5% Cust. #: WS-HM-16A No Asbestos Observed Other - 95% Material: Vinyl M/L Location:

Appearance: beige,fibrous,nonhomogenous Layer: 1 of 1

Lab ID #: 114312 - 32 Asbestos Present: NO Fiberglass - 5% Cust. #: WS-HM-16B No Asbestos Observed Other - 95% Material: Vinyl M/L Location:

Appearance: beige,fibrous,nonhomogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 14 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 33 Asbestos Present: NO Cellulose - 10%

Cust. #: WS-HM-17A No Asbestos Observed Fiberglass - 5% Material: Vinyl Yellow M/L Linoleum Other - 85% Location:

Appearance: beige,fibrous,nonhomogenous Layer: 1 of 4

Lab ID #: 114312 - 33a Asbestos Present: YES Other - 98% Cust. #: WS-HM-17A Chrysotile - 2% Material: Grey Floor Tile Location:

Appearance: grey,fibrous,homogenous Layer: 2 of 4

Lab ID #: 114312 - 33b Asbestos Present: NO Other - 100% Cust. #: WS-HM-17A No Asbestos Observed Material: Mastic Location:

Appearance: black,nonfibrous,homogenous Layer: 3 of 4

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 15 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 33c Asbestos Present: NO Cellulose - 60%

Cust. #: WS-HM-17A No Asbestos Observed Other - 40% Material: Felt Location:

Appearance: black,fibrous,homogenous Layer: 4 of 4

Lab ID #: 114312 - 34 Asbestos Present: NO Cellulose - 10% Cust. #: WS-HM-17B No Asbestos Observed Fiberglass - 5% Material: Vinyl Yellow M/L Linoleum Other - 85% Location:

Appearance: beige,fibrous,nonhomogenous Layer: 1 of 4

Lab ID #: 114312 - 34a Asbestos Present:

Cust. #: WS-HM-17B Material: Grey Floor Tile Location: NOT ANALYZED Appearance:

Layer: 2 of 4

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 16 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 34b Asbestos Present: NO Cellulose - 1%

Cust. #: WS-HM-17B No Asbestos Observed Other - 99% Material: Mastic Location:

Appearance: black,nonfibrous,homogenous Layer: 3 of 4

Lab ID #: 114312 - 34c Asbestos Present: NO Cellulose - 60% Cust. #: WS-HM-17B No Asbestos Observed Other - 40% Material: Felt Location:

Appearance: black,fibrous,homogenous Layer: 4 of 4

Lab ID #: 114312 - 35 Asbestos Present: NO Cellulose - 20% Cust. #: WS-HM-18A No Asbestos Observed Other - 80% Material: Drywall Location:

Appearance: white,fibrous,nonhomogenous Layer: 1 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 17 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 35a Asbestos Present: NO Other - 100%

Cust. #: WS-HM-18A No Asbestos Observed Material: Joint Compound Location:

Appearance: white,nonfibrous,homogenous Layer: 2 of 2

Lab ID #: 114312 - 36 Asbestos Present: NO Cellulose - 20% Cust. #: WS-HM-18B No Asbestos Observed Other - 80% Material: Drywall Location:

Appearance: white,fibrous,nonhomogenous Layer: 1 of 2

Lab ID #: 114312 - 36a Asbestos Present: NO Other - 100% Cust. #: WS-HM-18B No Asbestos Observed Material: Joint Compound Location:

Appearance: white,nonfibrous,homogenous Layer: 2 of 2

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 18 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 37 Asbestos Present: NO Other - 100%

Cust. #: WS-HM-19A No Asbestos Observed Material: Shower Trim Caulk Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 1

Lab ID #: 114312 - 38 Asbestos Present: NO Other - 100% Cust. #: WS-HM-19B No Asbestos Observed Material: Shower Trim Caulk Location:

Appearance: white,nonfibrous,homogenous Layer: 1 of 1

Lab ID #: 114312 - 39 Asbestos Present: NO Hair - 5% Cust. #: WS-HS-01A No Asbestos Observed Other - 95% Material: Plaster on Lathe Location:

Appearance: brown,fibrous,homogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 19 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 40 Asbestos Present: NO Hair - 5%

Cust. #: WS-HS-01B No Asbestos Observed Other - 95% Material: Plaster on Lathe Location:

Appearance: brown,fibrous,homogenous Layer: 1 of 1

Lab ID #: 114312 - 41 Asbestos Present: NO Hair - 5% Cust. #: WS-HS-01C No Asbestos Observed Other - 95% Material: Plaster on Lathe Location:

Appearance: brown,fibrous,homogenous Layer: 1 of 1

Lab ID #: 114312 - 42 Asbestos Present: NO Hair - 5% Cust. #: WS-HS-01D No Asbestos Observed Other - 95% Material: Plaster on Lathe Location:

Appearance: brown,fibrous,homogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 20 of 21

Report To: ARI Report # 24-114312 Mr. Aaron Paquet Date Collected: 11/20/24 Red Cedar Consulting Date Received: 11/21/24 P.O. Box 13216 Date Analyzed: 11/26/24 Lansing, MI 48901 Date Reported: 11/29/24

Project: 112 E. Wilkins St.

Project #: Jackson, MI

Sample Information Asbestos Type/Percent Non-Asbestos Material

Lab ID #: 114312 - 43 Asbestos Present: NO Hair - 5%

Cust. #: WS-HS-01E No Asbestos Observed Other - 95% Material: Plaster on Lathe Location:

Appearance: brown,fibrous,homogenous Layer: 1 of 1

Lab ID #: 114312 - 44 Asbestos Present: NO Hair - 5% Cust. #: WS-HS-01F No Asbestos Observed Other - 95% Material: Plaster on Lathe Location:

Appearance: brown,fibrous,homogenous Layer: 1 of 1

Lab ID #: 114312 - 45 Asbestos Present: NO Hair - 5% Cust. #: WS-HS-01G No Asbestos Observed Other - 95% Material: Plaster on Lathe Location:

Appearance: brown,fibrous,homogenous Layer: 1 of 1

For Layered Samples, each component will be analyzed and reported separately.

Robert T. Letarte Jr., Laboratory Director

Test Method EPA 40 CFR - Part 763 and/or EPA 600/R-93/116 was used to analyze the above samples. Matrix interference and/or resolution limits may yield false/negative results in certain circumstances. Suspect floor tiles containing <1% should be tested with SEM or TEM. This certificate of analysis relates only to the samples as submitted and to insure the integrity of the results, may only be reproduced in full. This certificate must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal

(734) 449-9990, Fax (734) 449-9991 Page 21 of 21

Attachment B Figure 1 Site Diagram

Figure 1a Site Diagram

Note: Figure created by Red Cedar Consulting Asbestos Sample Locations 112 E Wilkins St.

-Not To Scale- Jackson, MI

Figure 1b Site Diagram

Note: Figure created by Red Cedar Consulting Asbestos Sample Locations 112 E Wilkins St.

-Not To Scale- Jackson, MI

Tables

Table 1 - Summary of Hazardous Materials, 112 E Wilkins St. Jackson, Michigan

Hazardous Materials Description and Location

Location Material Description Quantity

No Hazardous Materials Identified

Table 2 - Summary of Sample Descriptions and Asbestos Laboratory Results, 112 E Wilkins St. Jackson, Michigan

Sample Number Sample Description Friable Material

Type Material

Classification % Asbestos

Laboratory Result Sample Location Approx. Material Quantity

WS-HM-01A Roofing Multilayer No M Category I ND/ND/ND/ND Building Exterior NA

WS-HM-01B Roofing Multilayer No M Category I ND/ND/ND/ND Building Exterior NA

WS-HM-02A Tar Paper Yes M Category II ND Building Exterior NA WS-HM-02B Tar Paper Yes M Category II ND Building Exterior NA

WS-HM-03A Window Trim Caulk No M Category II ND Bedroom 1 Exterior NA

WS-HM-03B Window Trim Caulk No M Category II ND Dining Exterior NA WS-HM-04A Basement Window Glazing Yes M Category II ND Basement NA

WS-HM-04B Basement Window Glazing Yes M Category II ND Basement NA

WS-HM-05A 1st Fl. Window Glazing Yes M Category II ND Dining NA WS-HM-05B 1st Fl. Window Glazing Yes M Category II ND Living NA

WS-HM-06A 2nd Fl. Window Glazing Yes M Category II ND 2nd Fl. Stairwell NA

WS-HM-06B 2nd Fl. Window Glazing Yes M Category II ND 2nd Fl. Living NA WS-HM-07A Chimney Caulk Basement No M Category II 10%CH Basement 2 sq. ft.

WS-HM-07B Chimney Caulk Basement No M Category II NA Basement NA

WS-HM-08A Duct Paper Yes M Category II 30%CH Basement Register Boots 45 sq. ft.

WS-HM-08B Duct Paper Yes M Category II NA Basement NA

WS-HM-09A Linoleum No M Category I ND Basement Stairs NA

WS-HM-09B Linoleum No M Category I ND Basement Stairs NA WS-HM-10A Vinyl Grey No M Category I ND Living NA

WS-HM-10B Vinyl Grey No M Category I ND Bedroom 1 NA

WS-HM-11A Linoleum Brown Multilayer No M Category I ND/ND Kitchen NA WS-HM-11B Linoleum Brown Multilayer No M Category I ND/ND Kitchen NA

WS-HM-12A Linoleum Yellow No M Category I ND Bathroom NA

WS-HM-12B Linoleum Yellow No M Category I ND Bathroom NA WS-HM-13A Brown Vinyl Wood No M Category I ND Dining NA

WS-HM-13B Brown Vinyl Wood No M Category I ND Stairwell Closet NA

WS-HM-14A 2’x4’ Ceiling Tile Yes M Category II ND Living Ceiling NA

Table 2 - Summary of Sample Descriptions and Asbestos Laboratory Results, 112 E Wilkins…