77244807 - Typicals.pdf

PDF 735 KB Posted

Attached to
26-032
Solicitation number
336-ITB26-032-3218-2027
Issued by
Polk County, Iowa

About this file

This file contains construction details and typical drawings for the Iowa Communications Network (ICN) relating to ICN OSP Project #77244807, a City of Des Moines cable relocation project in Polk County, Iowa. The document provides standardized construction specifications for handhole installations measuring 24 inches by 36 inches by 30 inches, including detailed diagrams for handhole placement, cable coiling, pedestal location, and grounding requirements. The specifications detail HDPE duct placement, fiber cable routing, tracer wire termination, and locate pedestal installation using TRI-VIEW pedestals with ISO levers. Key construction requirements include a minimum 5-foot right-of-way clearance, 3/4-inch crushed rock material (not pea gravel), proper cable tensioning and coiling around handhole walls, and ground rod installation in the handhole base with approximately 6 inches exposed above gravel. Tracer wire specifications call for #10 or #12 AWG solid copper wire for locate purposes and #6 or #8 AWG solid bare copper wire for grounding, with specific termination procedures including needle-nose plier eyelet bending and flat washer installation.

The document represents ICN's standard construction details and was updated on October 11, 2023, with previous revisions dating back to August 21, 2015. The drawings include revision histories and notes that this documentation is provided for general information purposes only and is not intended to determine precise ICN placement; contractors are instructed to call One Call (1-800-292-8989 or 811) before excavation. The file includes multiple sheets showing typical handhole cable coil arrangements, locate pedestal configurations, and comprehensive notes on locate wire bonding procedures using 3M SCOTCHLOK shield bonding kits and FOSC closure sealing kits. No specific pricing, set-asides, or contract award information is contained within this technical specification document.

View the file

Other files

File Type Posted
77244807 - ENGINEERING PLANS.pdf PDF
ITB - Construction Checklist 2025.pdf PDF
77244807 - Scope of Work (SOW).docx DOCX document
1471181-event.pdf PDF
26-032 ITB OSP #77244807 Polk Co - DSM fiber project.docx DOCX document

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

37 5/8"

30"

12" min.

6"

35 5/8"

26"

37 5/8"

37 5/8"

26"

R

I G

H

T

O

F

W

A

Y

5'

MIN.

5' 6" ±

4' TYP.

2-3'

HANDHOLE PLACEMENT TYPICAL

24" X 36" X 30" HAND HOLE

IOWA COMMUNICATIONS NETWORK

AutoCAD SHX Text 24"x36"x30" HAND HOLE

AutoCAD SHX Text

HDPE DUCT

AutoCAD SHX Text

CABLE

AutoCAD SHX Text

SOIL GRADE

AutoCAD SHX Text

FIBER

AutoCAD SHX Text

CABLE

AutoCAD SHX Text

FIBER

AutoCAD SHX Text

CABLE

AutoCAD SHX Text

HDPE

AutoCAD SHX Text

DUCT

AutoCAD SHX Text TAPE CABLES TOGETHER MATCHING LENGTHS WHERE POSSIBLE. COIL CABLE AROUND WALLS OF HANDHOLE

AutoCAD SHX Text

TYPICAL LOCATE PEDESTAL

AutoCAD SHX Text

TYPICAL SPLICE MARKER

AutoCAD SHX Text

STEEL POST (U- OR T-POST)

AutoCAD SHX Text

3/4" CRUSHED ROCK (NO GRAVEL INSIDE HH)

AutoCAD SHX Text

DO NOT USE PEA GRAVEL OR OTHER ROUND STONE

AutoCAD SHX Text

WIRE MESH

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

SIZE:

AutoCAD SHX Text

GRIMES STATE OFFICE BUILDING

AutoCAD SHX Text

ICN

AutoCAD SHX Text C

AutoCAD SHX Text

, COPY WITH PERMISSION

AutoCAD SHX Text O:\AutoCAD Standards\TYPICALS\TYPICAL-HH PLACEMENT.dwg

AutoCAD SHX Text

AutoCAD SHX Text

DES MOINES, IOWA 50319

AutoCAD SHX Text

400 EAST 14TH STREET

AutoCAD SHX Text

THIS DRAWING IS PROVIDED FOR GENERAL

AutoCAD SHX Text

INFORMATION ONLY AND IS NOT TO BE USED

AutoCAD SHX Text

TO DETERMINE PRECISE ICN PLACEMENT.

AutoCAD SHX Text

CALL ONE CALL BEFORE EXCAVATION

AutoCAD SHX Text

(1-800-292-8989 OR 811)

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

REVISION

AutoCAD SHX Text

REVISION

AutoCAD SHX Text

REVISION

AutoCAD SHX Text

REVISION

AutoCAD SHX Text

REVISION

AutoCAD SHX Text

REVISION

AutoCAD SHX Text

REVISION

AutoCAD SHX Text

REVISION

AutoCAD SHX Text 8-21-15

AutoCAD SHX Text 8-19-16

AutoCAD SHX Text 8-24-16

AutoCAD SHX Text 12-11-17

AutoCAD SHX Text 7-19-18

AutoCAD SHX Text 11-4-19

AutoCAD SHX Text 6-30-21

AutoCAD SHX Text 10-11-23

AutoCAD SHX Text

CONSTRUCTION DETAIL

AutoCAD SHX Text

HANDHOLE TYPICAL - ICN STANDARD

AutoCAD SHX Text 24" x 36" x 30"

AutoCAD SHX Text

NONE

AutoCAD SHX Text 11 x 17

AutoCAD SHX Text

TYPICAL HANDHOLE

CABLE COILS NOT SHOWN

TYPICAL INSTALLATION OF

TRI-VIEW LOCATE PEDESTAL

NOTES:

-LOCATE (TRACER) WIRE: #10 or #12 AWG SOLID COPPER WIRE

-GROUND WIRE: #6 OR #8 AWG SOLID BARE COPPER WIRE

-GROUND ROD: INSTALL IN BASE OF HANDHOLE, CORNER NEAREST LOCATE PEDESTAL, LEAVE ~6-IN EXPOSED ABOVE

GRAVEL -ONE LOCATE WIRE PER FIBER CABLE AT SPLICE ENCLOSURE

-LOCATE WIRE(S) TO BE BONDED INSIDE SPLICE ENCLOSURE WITH 3M SCOTCHLOK SHIELD BONDING KIT -LOCATE WIRE(S) TO BE ROUTED OUTSIDE OF SPLICE ENCLOSURE WITH FOSC CLOSURE SEALING KIT -LOCATE WIRE(S) TO BE ROUTED VIA DUCT TO LOCATE PEDESTAL AND TERMINATED AT TERMINAL BOARD -GROUND LOCATE PEDESTAL TO GROUND ROD WITH SOLID BARE COPPER WIRE AND GROUND CLAMP

-SECURE LOCATE PEDESTAL BY PLACING OVER STEEL POST

-SET PEDESTAL AT OR NEAR RIGHT-OF-WAY, IF POSSIBLE

-MINIMUM HEIGHT OF INSTALLED PEDESTAL MUST BE 5 FEET

TRACER WIRE TERMINATION DETAIL

Termination of the locate wire at either a pedestal, puck, or in a splice case shall be made in the following fashion:

Strip off a minimum of ¾” of insulation. Using a needle nose pliers bend a wire “eyelet” on the wire end in a clockwise manner. Use a flat washer on both sides of the wire eyelet when cinching it down on the stud. Flat washers shall be of appropriate size such that the hole matches the diameter of the stud and the outside diameter of the flat washer matches reasonably close to the eyelet diameter.

IOWA COMMUNICATIONS NETWORK

AutoCAD SHX Text

HAND HOLE

AutoCAD SHX Text

HDPE DUCT

AutoCAD SHX Text

CABLE

AutoCAD SHX Text

SOIL GRADE

AutoCAD SHX Text

GROUND ROD (6" EXPOSED)

AutoCAD SHX Text

DUCT (ANY)

AutoCAD SHX Text

LOCATE WIRES

AutoCAD SHX Text

GROUND WIRE

AutoCAD SHX Text S P L I C E

AutoCAD SHX Text

STEEL POST

AutoCAD SHX Text

TERMINAL BOARD

AutoCAD SHX Text

3/4" CRUSHED ROCK

AutoCAD SHX Text

BOND LOCATE WIRES INSIDE SPLICE ENCLOSURE

AutoCAD SHX Text

GROUND WIRE BONDED TO GROUND ROD

AutoCAD SHX Text

OUTSIDE DIAMETER MUST

AutoCAD SHX Text

FIT WITHIN PEDESTAL

AutoCAD SHX Text

WITH STEEL POST

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

SIZE:

AutoCAD SHX Text

GRIMES STATE OFFICE BUILDING

AutoCAD SHX Text

ICN

AutoCAD SHX Text C

AutoCAD SHX Text

, COPY WITH PERMISSION

AutoCAD SHX Text O:\AutoCAD Standards\TYPICALS\TYP_LOCATE PEDS.dwg

AutoCAD SHX Text

AutoCAD SHX Text

DES MOINES, IOWA 50319

AutoCAD SHX Text

400 EAST 14TH STREET

AutoCAD SHX Text

THIS DRAWING IS PROVIDED FOR GENERAL

AutoCAD SHX Text

INFORMATION ONLY AND IS NOT TO BE USED

AutoCAD SHX Text

TO DETERMINE PRECISE ICN PLACEMENT.

AutoCAD SHX Text

CALL ONE CALL BEFORE EXCAVATION

AutoCAD SHX Text

(1-800-292-8989 OR 811)

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

FOR CONSTRUCTION

AutoCAD SHX Text

UPDATE

AutoCAD SHX Text

REVISION

AutoCAD SHX Text

REVISION

AutoCAD SHX Text

REVISION

AutoCAD SHX Text

REVISION

AutoCAD SHX Text 11-3-14

AutoCAD SHX Text 3-13-15

AutoCAD SHX Text 8-21-15

AutoCAD SHX Text 9-4-15

AutoCAD SHX Text 5-19-17

AutoCAD SHX Text 10-11-23

AutoCAD SHX Text

CONSTRUCTION DETAIL

AutoCAD SHX Text

LOCATE PEDESTAL TYPICAL

AutoCAD SHX Text

TRI-VIEW W/ISO LEVER

AutoCAD SHX Text

NONE

AutoCAD SHX Text 11 x 17

AutoCAD SHX Text

TYPICAL LOCATE PEDESTAL

Sheets and Views
HH TYP STANDARD_polymer concrete
TYP_LOCATE PEDS-TRIVIEW.pdf
Sheets and Views
TRIVIEW

File details come from the government source that posted it. Updated .