SLEDGE_Lead_Assessment_Report_(Mar17).pdf

6.0 FINDINGS AND ASSESSMENTS (LEAD BASED PAINT)

PAINT FILM QUALITY

Intact (surface deterioration is <2 SF or 10%)

Deteriorated (surface deterioration is >2 SF or 10%)

CATEGORIES OF PAINT DETERIORATION

Surface Coat Failure: top layer of paint is flaking, peeling, or otherwise detaching from layers below

Multi-Layer Coat Failure: several top layers are delaminating from layers below, i.e. blistering, flaking, peeling

Paint Failure: due to unsound substrate, i.e. rotted wood, rust

Paint Abrasion: paint is rubbing from mechanical or human friction

Chipped Paint: pieces of paint are loosened or broken due to impact

6.1 Tender One Hold

Location Paint Film Quality Categories of Paint Deterioration

Intact Deteriorated Surface

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X X

Deck X X X

Forward Bulkhead X X X X

AFT Bulkhead X X X X

Port Bulkhead X X X X

Starboard Bulkhead X X X X

Lead Dust Wipe Sampling Sample # Sample Location Material

Description Sample Result

(microgram/ft2) Greater than

SFLC 0000

Notes

OH – LW01 One Hold Starboard Floor

Wipe 15.5 No

OH – LW02 One Hold Starboard Overhead

Wipe 11 No

OH – LW03 One Hold Starboard Bulkhead

Wipe 15.7 No

OH – LW04 One Hold Forward Bulkhead

Wipe <10 No

OH – LW05 One Hold Port Bulkhead

Wipe 13.5 No

OH – LW06 One Hold Port Forward Floor

Wipe 43.8 No

OH – LW07 One Hold Starboard Bilge

Wipe 26.4 No

OH – LW08 One Hold Center Waste Pipe

Wipe <10 No

OH – LW09 One Hold Forward Exhaust Fan

Wipe 115 No

OH – LW10 One Hold Center AFT Light

Wipe 16 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and food prep areas and 200 micrograms/ft2 for all other areas.

Recommendations

Throughout Area:

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned using HEPA vacuums and wet wipes to ensure levels of lead dust do not exceed the permissible exposure limit.

• If other materials are found and suspected to contain lead they should be tested before disturbed. Deteriorated areas should be abated or stabilized if found to contain lead.

Overhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Aft Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Starboard Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Forward Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Port Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Other:

• Center Waste Pipe o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Forward Exhaust Fan o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Center Aft Light o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard o Recommend bulk paint chip sampling.

6.2 Barge BOSN Hole

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X

Deck X X X

Forward Bulkhead X X X

AFT Bulkhead X X X

Port Bulkhead X X X

Starboard Bulkhead X X X

Description Sample Result

(microgram/ft2) Greater than

SFLC 0000

Notes

BH – LW01 BOSN Hole AFT Port Floor

Wipe 31.3 No

BH – LW02 BOSN Hole AFT Port Overhead

Wipe <10 No

BH – LW03 BOSN Hole AFT Port Bulkhead

Wipe <10 No

BH – LW04 BOSN Hole AFT Center Floor

Wipe 19.3 No

BH – LW05 BOSN Hole AFT Center Overhead

Wipe <10 No

BH – LW06 BOSN Hole Forward Starboard

Floor

Wipe 186.3 No

BH – LW07 BOSN Hole Forward Starboard

Bulkhead

Wipe <10 No

BH – LW08 BOSN Hole Forward Center Floor

Wipe 19.8 No

BH – LW09 BOSN Hole Yellow Locker

Wipe <10 No

BH – LW10 BOSN Hole Forward Center Locker

Wipe <10 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned using HEPA vacuums and wet wipes to ensure levels of lead dust do not exceed the permissible exposure limit.

• If other materials are found and suspected to contain lead they should be tested before

Overhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

• New deck plates have recently been installed in many of the areas.

Aft Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Starboard Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Forward Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Port Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Other:

• Yellow Locker o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Forward Center Locker o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

6.3 Barge Engine Room

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X

Deck X X X

Forward Bulkhead X X X

AFT Bulkhead (I-Beams & L-Beams)

X X X

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

BER – LW01 Barge Engine Room Port AFT Floor

Wipe 11.2 No

BER – LW02 Barge Engine Room Port AFT Bulkhead

Wipe <10 No

BER – LW03 Barge Engine Room Port AFT Overhead

Wipe <10 No

BER – LW04 Barge Engine Room AFT Center Floor

Wipe 15.6 No

BER – LW05 Barge Engine Room AFT Center Overhead

Wipe <10 No

BER – LW06 Barge Engine Room Port Forward Floor

Wipe 18.6 No

BER – LW07 Barge Engine Room Starboard AFT Floor

Wipe 45.5 No

BER – LW08 Barge Engine Room Forward Center

Overhead

Wipe <10 No

BER – LW09 Barge Engine Room Forward Starboard

Floor

Wipe 45.2 No

BER – LW10 Barge Engine Room Forward Center Exhaust Tube

Wipe 152.6 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned permissible exposure limit.

• If other materials are found and suspected to contain lead they should be tested before disturbed. Deteriorated areas should be abated or stabilized if found to contain lead.

Overhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

• New deck plates have recently been installed in many of the areas.

AFT Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Starboard Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Forward Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Port Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Other:

• Forward Center Exhaust Tube o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

6.4 Barge Forward Engineering

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X X

Deck X X X X X

Forward Bulkhead X X X

AFT Bulkhead X X X

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

FE – LW01 Forward Engineering Forward Center Floor

Wipe 37.6 No

FE – LW02 Forward Engineering Forward Center

Overhead

Wipe <10 No

FE – LW03 Forward Engineering Forward Center

Bulkhead

Wipe <10 No

FE – LW04 Forward Engineering Center Floor

Wipe 46.9 No

FE – LW05 Forward Engineering Starboard Center Bilge

Wipe 82.7 No

FE – LW06 Forward Engineering Port AFT Bulkhead

Wipe 10.9 No

FE – LW07 Forward Engineering Forward Eng Locker

Wipe 35.7 No

FE – LW08 Forward Engineering AFT Center Floor

Wipe 89.4 No

FE – LW09 Forward Engineering AFT Red Toolbox

Wipe 90.8 No

FE – LW10 Forward Engineering Overhead Red Pipe

Wipe <10 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned

Overhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

AFT Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Starboard Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Forward Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Port Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Other:

• Forward Eng. Locker o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• AFT Red Toolbox o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Overhead Red Pipe o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

6.5 Barge Line Locker

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X X

Deck X X X

Forward Bulkhead X X X

AFT Bulkhead X X X X

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

LL – LW01 Barge Line Locker AFT Starboard Floor

Wipe 319.2 Yes

LL – LW02 Barge Line Locker AFT Starboard Pipe

Wipe 24.9 No

LL – LW03 Barge Line Locker Center Floor

Wipe 220.5 Yes

LL – LW04 Barge Line Locker Center Overhead

Wipe <10 No

LL – LW05 Barge Line Locker Center Bilge

Wipe 364.5 Yes

LL – LW06 Barge Line Locker Port Forward Bilge

Wipe 114.2 No

LL – LW07 Barge Line Locker Starboard Forward

Bulkhead

Wipe <10 No

LL – LW08 Barge Line Locker Port Forward Vent Pipe

Wipe 10.2 No

LL – LW09 Barge Line Locker Port Forward Bulkhead

Wipe 14.2 No

LL – LW10 Barge Line Locker Forward Center Light

Wipe 12.3 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned using HEPA vacuums and wet wipes to ensure levels of lead dust do not exceed the permissible exposure limit.

Specification 0000.

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were above than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

• The entire compartment should be HEPA vacuumed and wet wiped.

AFT Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Starboard Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Forward Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Port Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

• Recommend bulk paint chip sampling.

6.6 Forward ATON Hold

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X X

Deck X X X

Forward Bulkhead X X X X

AFT Bulkhead X X X X

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

FA – LW01 Forward ATON Center Bilge

Wipe 67.7 No

FA – LW02 Forward ATON Center Overhead

Wipe <10 No

FA – LW03 Forward ATON Forward Bulkhead

Wipe <10 No

FA – LW04 Forward ATON Port Forward Bulkhead

Wipe 19 No

FA – LW05 Forward ATON AFT Center Light

Wipe 27.4 No

FA – LW06 Forward ATON AFT Bilge Center

Wipe 141.6 No

FA – LW07 Forward ATON Starboard Bulkhead

Wipe <10 No

FA – LW08 Forward ATON AFT Vent Pipe

Wipe 16.1 No

FA – LW09 Forward ATON AFT Bulkhead

Wipe <10 No

FA – LW10 Forward ATON AFT Hanging Shelf

Wipe <10 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned using HEPA vacuums and wet wipes to ensure levels of lead dust do not exceed the permissible exposure limit.

• If other materials are found and suspected to contain lead they should be tested before

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

AFT Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Starboard Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Forward Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Port Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Other:

• AFT Center Light o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• AFT Vent Pipe o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• AFT Hanging Shelf o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

6.7 Barge Rigging Hold

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X

Deck X X X

Forward Bulkhead X X X

AFT Bulkhead X X X

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

RH – LW01 Barge Rigging Hold Port Bilge

Wipe 17 No

RH – LW02 Barge Rigging Hold Port Forward Bulkhead

Wipe <10 No

RH – LW03 Barge Rigging Hold Port Bulkhead

Wipe <10 No

RH – LW04 Barge Rigging Hold Center Bilge Floor

Wipe 20 No

RH – LW05 Barge Rigging Hold AFT Center Pipe

Wipe <10 No

RH – LW06 Barge Rigging Hold Center Overhead

Wipe <10 No

RH – LW07 Barge Rigging Hold Starboard Bulkhead

Wipe <10 No

RH – LW08 Barge Rigging Hold Forward Heater

Wipe 13.2 No

RH – LW09 Barge Rigging Hold Starboard Forward

Bulkhead

Wipe <10 No

RH – LW10 Barge Rigging Hold AFT Center Bulkhead

Wipe <10 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned using HEPA vacuums and wet wipes to ensure levels of lead dust do not exceed the permissible exposure limit.

Specification 0000.

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

AFT Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Starboard Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Forward Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Port Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Other:

• AFT Center Pipe o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Forward Heater o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

6.8 Barge EM Shop

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X X X

Deck X X X X X

Forward Bulkhead X X X

AFT Bulkhead X X X

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

ES – LW01 EM Shop Forward Overhead

Hatch

Wipe 38.1 No

ES – LW02 EM Shop Starboard Forward

Bilge

Wipe 59.8 No

ES – LW03 EM Shop Forward Center Floor

Wipe 19.3 No

ES – LW04 EM Shop Forward Center

Overhead

Wipe <10 No

ES – LW05 EM Shop Port Forward Bulkhead

Wipe <10 No

ES – LW06 EM Shop Forward Heater

Wipe 16.3 No

ES – LW07 EM Shop AFT Port Floor

Wipe 84.4 No

ES – LW08 EM Shop AFT Center Bulkhead

Wipe <10 No

ES – LW09 EM Shop Starboard AFT Light

Wipe 341.9 Yes

ES – LW10 EM Shop Port AFT Overhead

Wipe <10 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned

Overhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

AFT Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Starboard Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Forward Bulkhead

• No sampling was performed.

• Recommend bulk paint chip sampling.

Port Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Other:

• Forward Heater o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Starboard AFT Light o Lead Dust Wipe sampling was performed and results were above than SFLC Standard

Specification 0000.

o The entire compartment should be HEPA vacuumed and wet wiped.

6.9 Tender Ventilation

Coat

Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Three Ducts Facing FWD X N/A N/A N/A N/A N/A

Three Ducts Facing AFT X N/A N/A N/A N/A N/A

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

VT – LW01 Ventilation Tender Starboard Forward

Vent

Wipe 16.2 No

VT – LW02 Ventilation Tender Forward Center Vent

Wipe 67.1 No

VT – LW03 Ventilation Tender Port Discharge Vent

Wipe 22.4 No

VT – LW04 Ventilation Tender Starboard Ex Vent AFT

Wipe 18.7 No

VT – LW05 Ventilation Tender Venter Ex Vent AFT

Wipe 37.3 No

VT – LW06 Ventilation Tender Port Ex Vent Pipe

Wipe 15.5 No

VT – LW07 Ventilation Tender Port AFT Vent Pipe

Wipe 28.9 No

VT – LW08 Ventilation Tender Starboard Duct Blanket

Wipe 18.5 No

VT – LW09 Ventilation Tender Forward Duct Pipe

Wipe 52.7 No

VT – LW10 Ventilation Tender AFT Duct Pipe Cover

Wipe 17.7 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned using HEPA vacuums and wet wipes to ensure levels of lead dust do not exceed the permissible exposure limit.

• If other materials are found and suspected to contain lead they should be tested before disturbed. Deteriorated areas should be abated or stabilized if found to contain lead.

Ventilation Ducts (6 ducts were not painted):

6.10 Tender Mess Deck & Galley

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X X

Deck X X X

Forward Bulkhead X X X

AFT Bulkhead X X X

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

MD – LW01 Mess Deck Forward Floor Port

Wipe 10.8 No

MD – LW02 Mess Deck Port Forward

Overhead

Wipe <10 No

MD – LW03 Mess Deck Port Forward Bulkhead

Wipe <10 No

MD – LW04 Mess Deck AFT Prep Table

Wipe <10 No

MD – LW05 Mess Deck Port Heater Vent

Intake

Wipe <10 No

MD – LW06 Mess Deck Port Heater Ex Vent

Wipe 10 No

MD – LW07 Mess Deck Center Floor

Wipe 12 No

MD – LW08 Mess Deck Center AFT Bulkhead

Wipe <10 No

MD – LW09 Mess Deck Starboard Bulkhead

Wipe <10 No

MD – LW10 Mess Deck Starboard Floor

Wipe 11 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned using HEPA vacuums and wet wipes to ensure levels of lead dust do not exceed the

• Area was difficult to assess due to the paneling.

Overhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

• The coaming had a large amount of chipping from impact but still considered intact.

AFT Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Forward Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Port Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Starboard Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Other:

• AFT Prep Table o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Port Heater Vent Intake o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Port Heater Ex Vent o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

6.11 Tender CO Berthing Area

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X

Deck X X X

Forward Bulkhead X X X

AFT Bulkhead X X X

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

CO – LW01 CO Berthing Area Center Floor

Wipe <10 No

CO – LW02 CO Berthing Area Port Bulkhead

Wipe <10 No

CO – LW03 CO Berthing Area Forward Bulkhead

Wipe <10 No

CO – LW04 CO Berthing Area Center Overhead

Wipe 13.3 No

CO – LW05 CO Berthing Area Left Desk Top

Wipe <10 No

CO – LW06 CO Berthing Area AFT Bulkhead

Wipe <10 No

CO – LW07 CO Berthing Area Forward Starboard

Bulkhead

Wipe <10 No

CO – LW08 CO Berthing Area Forward Heater Vent

Wipe <10 No

CO – LW09 CO Berthing Area Forward Heater Intake

Wipe <10 No

CO – LW10 CO Berthing Area AFT Center Floor

Wipe <10 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned using HEPA vacuums and wet wipes to ensure levels of lead dust do not exceed the

• Area was difficult to assess due to the paneling and carpeting.

Overhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

AFT Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Forward Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Port Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Starboard Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Other:

• Left Desk Top o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Forward Heater Vent o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Forward Heater Intake o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

6.12 Tender EPO/XPO Berthing Area

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X

Deck X X X

Forward Bulkhead X X X

AFT Bulkhead X X X

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

EPO – LW01 EPO Berthing Area Forward Port Floor

Wipe <10 No

EPO – LW02 EPO Berthing Area Port Forward

Overhead

Wipe 10.9 No

EPO – LW03 EPO Berthing Area State Room Door

Wipe <10 No

EPO – LW04 EPO Berthing Area Starboard Bulkhead

Wipe <10 No

EPO – LW05 EPO Berthing Area Port Bulkhead

Wipe <10 No

EPO – LW06 EPO Berthing Area AFT Bulkhead

Wipe <10 No

EPO – LW07 EPO Berthing Area Heater Intake

Wipe <10 No

EPO – LW08 EPO Berthing Area Heater Exhaust Vent

Wipe <10 No

EPO – LW09 EPO Berthing Area Starboard Light

Wipe <10 No

EPO – LW10 EPO Berthing Area Storage Locker Top

Wipe <10 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned using HEPA vacuums and wet wipes to ensure levels of lead dust do not exceed the

• Area was difficult to assess due to the paneling and carpeting.

Overhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

AFT Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Forward Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Port Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Starboard Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Other:

• State Room Door o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Heater Intake o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Heater Exhaust Vent o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Starboard Light o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

• Storage Locker Top o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

6.13 Tender Crew Berthing Area

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X

Deck X X X

Forward Bulkhead X X X

AFT Bulkhead X X X

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

CB – LW01 Crew Berthing Port Door

Wipe <10 No

CB – LW02 Crew Berthing Port Forward Floor

Wipe <10 No

CB – LW03 Crew Berthing AFT Locker

Wipe <10 No

CB – LW04 Crew Berthing Center Aft Floor

Wipe <10 No

CB – LW05 Crew Berthing Center Overhead

Wipe <10 No

CB – LW06 Crew Berthing Starboard Bulkhead

Wipe <10 No

CB – LW07 Crew Berthing Forward Bulkhead

Wipe <10 No

CB – LW08 Crew Berthing Starboard Center Floor

Wipe <10 No

CB – LW09 Crew Berthing AFT Center Bunk

Wipe <10 No

CB – LW10 Crew Berthing Heater Ex Vent

Wipe <10 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned using HEPA vacuums and wet wipes to ensure levels of lead dust do not exceed the permissible exposure limit.

• Area was difficult to assess due to the paneling, bunks, lockers, etc.

Specification 0000.

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

AFT Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Forward Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Port Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Starboard Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Other:

• Port Door o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• AFT Locker o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• AFT Center Bunk o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Heater Ex Vent o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

6.14 Tender Engine Room

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X X

Deck X X X

Forward Bulkhead X X X

AFT Bulkhead X X X

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

TER – LW01 Tender Engine Room Center Floor

Wipe 17 No

TER – LW02 Tender Engine Room Center Overhead

Wipe 19 No

TER – LW03 Tender Engine Room Port Bulkhead

Wipe 16.5 No

TER – LW04 Tender Engine Room Forward Bulkhead

Wipe 11.3 No

TER – LW05 Tender Engine Room Port Electric Panel Top

Wipe 14.2 No

TER – LW06 Tender Engine Room Starboard F. O. Tank

Door

Wipe 12.8 No

TER – LW07 Tender Engine Room AFT Bulkhead

Wipe 12.5 No

TER – LW08 Tender Engine Room AFT Center Floor

Wipe 28.4 No

TER – LW09 Tender Engine Room Middle Step

Wipe 23.9 No

TER – LW10 Tender Engine Room Starboard Bulkhead

Wipe 22.2 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned using HEPA vacuums and wet wipes to ensure levels of lead dust do not exceed the

• Area was difficult to assess due to the paneling.

Overhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

AFT Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Forward Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Port Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Starboard Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Other:

• Port Electrical Panel Top o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Starboard F. O. Tank Door o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Middle Step o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

6.15 Tender Shaft Alley

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X

Deck X X X X

Forward Bulkhead X X X

AFT Bulkhead X X X

Lead Bulk Sampling

Description

Sample Result (By Weight)

Greater than HUD Standard

(0.5 % by weight)

Notes

SA – L01 Shaft Alley Port Bulkhead

Forward

Multi-Layer Paint

<0.0084% No See Note A

SA – L02 Shaft Alley Forward Bulkhead

Forward

Multi-Layer Paint

<0.0091% No See Note A

Note A: Although the sample is less than the Permissible Exposure Limit, the paint still contains lead and should be handled accordingly.

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

SA – LW01 Shaft Alley Starboard Forward

Floor

Wipe 23.9 No

SA – LW02 Shaft Alley Hydraulic Steering

Tank

Wipe <10 No

SA – LW03 Shaft Alley Starboard Forward

Bulkhead

Wipe <10 No

SA – LW04 Shaft Alley AFT Floor

Wipe 21.7 No

SA – LW05 Shaft Alley Forward Starboard

Heater

Wipe 17.7 No

SA – LW06 Shaft Alley Potable Water Tank

Wipe <10 No

SA – LW07 Shaft Alley Forward Center Floor

Wipe 22.4 No

SA – LW08 Shaft Alley Forward Center Bilge

Wipe 11.8 No

SA – LW09 Shaft Alley AFT Center Overhead

Wipe <10 No

SA – LW10 Shaft Alley Port Bulkhead

Wipe <10 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned using HEPA vacuums and wet wipes to ensure levels of lead dust do not exceed the permissible exposure limit.

• Area was difficult to assess due to insulation.

• If other materials are found and suspected to contain lead they should be tested before disturbed. Deteriorated areas should be abated or stabilized if found to contain lead.

Overhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Bulk paint chip sampling was not performed because Lt. Troch indicated that it was already confirmed to contain lead. If the area begins to deteriorate, the deck should be abated or stabilized.

AFT Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Forward Bulkhead:

• No Lead Dust Wipe sampling was performed.

• Bulk sampling was performed and the results were lower than HUD standards (0.5% by weight).

Port Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Bulk sampling was performed and the results were lower than HUD standards (0.5% by weight).

Starboard Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Other:

• Hydraulic Steering Tank o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Forward Starboard Heater o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Potable Water Tank o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

6.16 Tender Main Deck Passageways & Ladders

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X

Deck X X X

Forward Bulkhead X X X

AFT Bulkhead X X X

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

MP – LW01 Main Passage AFT Door

Wipe <10 No

MP – LW02 Main Passage AFT Overhead Panel

Wipe <10 No

MP – LW03 Main Passage AFT Port Bulkhead

Wipe <10 No

MP – LW04 Main Passage Center Floor

Wipe <10 No

MP – LW05 Main Passage Heating Unit Vent

Wipe <10 No

MP – LW06 Main Passage Starboard Center

Bulkhead

Wipe <10 No

MP – LW07 Main Passage Fire Ext. Center

Wipe <10 No

MP – LW08 Main Passage Forward Floor

Wipe <10 No

MP – LW09 Main Passage Forward Overhead

Panel

Wipe 10.3 No

MP – LW10 Main Passage Starboard Forward

Bulkhead

Wipe <10 No

MP – LW11 Main Passage Starboard Fuse Panel

Cover

Wipe <10 No

MP – LW12 Main Passage Overhead Smoke Det.

Wipe <10 No

MP – LW13 Main Passage AFT Floor

Wipe <10 No

MP – LW14 Main Passage Port Bulletin Board

Wipe <10 No

MP – LW15 Main Passage Top Starboard Bulletin

Board

Wipe <10 No

MP – LW16 Main Passage Port Side Vent

Wipe <10 No

MP – LW17 Main Passage Forward Port Window

Sill

Wipe <10 No

MP – LW18 Main Passage Forward Port Combing

Wipe <10 No

MP – LW19 Main Passage Em. Light Unit

Wipe <10 No

MP – LW20 Main Passage Center Overhead Light

Wipe <10 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned using HEPA vacuums and wet wipes to ensure levels of lead dust do not exceed the permissible exposure limit.

• Area was difficult to assess due to the paneling.

• If other materials are found and suspected to contain lead they should be tested before disturbed. Deteriorated areas should be abated or stabilized if found to contain lead.

Overhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

AFT Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Forward Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Port Bulkhead:

Starboard Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Other:

• AFT Door o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Heating Unit Vent o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Fire Ext Center o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• STBD Fuse Panel Cover o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Port Side Vent o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• EM Light Unit o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Center Overhead Light o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

6.17 Tender 01 Deck Passageways & Ladders

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X

Deck X X X

Forward Bulkhead X X X

AFT Bulkhead X X X

Port Bulkhead X X X

Ladders X

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

01P – LW01 01 Passage Starboard Bulkhead

Wipe <10 No

01P – LW02 01 Passage Center Overhead

Wipe 13.3 No

01P – LW03 01 Passage Center Floor

Wipe 10.3 No

01P – LW04 01 Passage Port Bulkhead

Wipe <10 No

01P – LW05 01 Passage Stairwell to Pilothouse

Wipe 12 No

01P – LW06 01 Passage Lower Hand Rail

Wipe <10 No

01P – LW07 01 Passage Lower Stairs

Wipe 12.3 No

01P – LW08 01 Passage Overhead Light

Wipe <10 No

01P – LW09 01 Passage Port Side Combing

Wipe 15.5 No

01P – LW10 01 Passage Port Floor

Wipe <10 No

01P – LW11 01 Passage Port AFT Bulkhead

Wipe <10 No

01P – LW12 01 Passage Starboard AFT

Bulkhead

Wipe <10 No

01P – LW13 01 Passage AFT Floor

Wipe 10.3 No

01P – LW14 01 Passage Bottom Step Lower

Wipe 26.7 No

01P – LW15 01 Passage Portrait on AFT

Bulkhead

Wipe <10 No

01P – LW16 01 Passage Forward Port Combing

Wipe <10 No

01P – LW17 01 Passage Upper Hand Rail

Wipe <10 No

01P – LW18 01 Passage Upper Bottom Step

Wipe 37.1 No

01P – LW19 01 Passage Upper Step Top

Stairwell

Wipe <10 No

01P – LW20 01 Passage Emergency Light

Wipe 16 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned using HEPA vacuums and wet wipes to ensure levels of lead dust do not exceed the permissible exposure limit.

• Area was difficult to assess due to the paneling.

• If other materials are found and suspected to contain lead they should be tested before disturbed. Deteriorated areas should be abated or stabilized if found to contain lead.

Overhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

AFT Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Forward Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Port Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Starboard Bulkhead:

• Stairwell to Pilot House o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Lower Handrail o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Lower Stairs o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Overhead Light o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Bottom Step Lower o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Upper Handrail o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Upper Bottom Step o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Upper Step Top Stairwell o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Emergency Light o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

6.18 Lazarette

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X X

Deck X X X X X

Forward Bulkhead X X X

AFT Bulkhead X X X

Description

Sample Result (By Weight)

Greater than HUD Standard

(0.5 % by weight)

Notes

LAZ – L01 Lazarette Overhead Center

Multi-Layer Paint

<0.0071% No See Note A

LAZ – L02 Lazarette Port Bulkhead

Forward

Multi-Layer Paint

<0.0369% No See Note A

LAZ - 03 Lazarette AFT Bulkhead

Center

Multi-Layer Paint

<0.0331% No See Note A

Note A: Although the sample is less than the Permissible Exposure Limit, the paint still contains lead and should be

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

LAZ – LW01 Lazarette Starboard Forward

Bilge

Wipe 28.4 No

LAZ – LW02 Lazarette Starboard Forward

Bulkhead

Wipe 148.3 No

LAZ – LW03 Lazarette Starboard Overhead

Wipe 20 No

LAZ – LW04 Lazarette Center Ingot Cover

Wipe 44.3 No

LAZ – LW05 Lazarette Forward Center Pipe

Wipe 78.5 No

LAZ – LW06 Lazarette Starboard Rudder

Housing

Wipe 18.2 No

LAZ – LW07 Lazarette Starboard AFT

Bulkhead

Wipe 24.7 No

LAZ – LW08 Lazarette Port Bilge

Wipe 18.7 No

LAZ – LW09 Lazarette Port Overhead

Wipe 433.7 Yes

LAZ – LW10 Lazarette Port AFT Bulkhead

Wipe 156.2 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned using HEPA vacuums and wet wipes to ensure levels of lead dust do not exceed the permissible exposure limit.

• If other materials are found and suspected to contain lead they should be tested before disturbed. Deteriorated areas should be abated or stabilized if found to contain lead.

Overhead:

• Lead Dust Wipe sampling was performed and results were above the SFLC Standard Specification 0000.

• Bulk sampling was performed and the results were lower than HUD standards (0.5% by weight).

• The entire compartment should be HEPA vacuumed and wet wiped.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

AFT Bulkhead:

• No Lead Dust Wipe sampling was performed.

• Bulk sampling was performed and the results were lower than HUD standards (0.5% by weight).

Forward Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Port Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Bulk sampling was performed and the results were lower than HUD standards (0.5% by weight).

Starboard Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

• Starboard Rudder Housing o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Forward Center Pipe o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Center Ingot Cover o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

6.19 MSD Space

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X X

Deck X X X X

Forward Bulkhead X X X

AFT Bulkhead X X X

Port Bulkhead X X X

Sewage Tank X X X X

Description

Sample Result (By Weight)

Greater than HUD Standard

(0.5 % by weight)

Notes

MSD – L01 MSD Space Overhead Pipe

Center

Multi-Layer Paint

0.9227% Yes

Note A: Although the sample is less than the Permissible Exposure Limit, the paint still contains lead and should be

Description

Sample Result (microgram/ft2)

Greater than

SFLC 0000

Notes

MSD – LW01 MSD

Entry Way Step

Wipe 15.2 No

MSD – LW02 MSD

Center AFT Bulkhead

Wipe 20.2 No

MSD – LW03 MSD

Port AFT Floor

Wipe 44.3 No

MSD – LW04 MSD

Top of Waste Tank

Wipe 25.4 No

MSD – LW05 MSD

Forward Bulkhead Port

Wipe 49.7 No

MSD – LW06 MSD

Starboard Bilge

Wipe 43.5 No

MSD – LW07 MSD

AFT Center Overhead

Pipe

Wipe 19.2 No

MSD – LW08 MSD

Starboard Bulkhead

Wipe 34.6 No

MSD – LW09 MSD

Starboard Floor

Wipe 14 No

MSD – LW10 MSD

Starboard Overhead

Wipe 11.3 No

Note: SFLC Standard Specification 000 threshold for lead wipe sampling is 40 microgram/ft2 for berthing and

• Panel vibration has the potential to cause lead dust.

• Due to potential lead dust hazards, it is recommended that the area be regularly cleaned using HEPA vacuums and wet wipes to ensure levels of lead dust do not exceed the permissible exposure limit.

• If other materials are found and suspected to contain lead they should be tested before disturbed. Deteriorated areas should be abated or stabilized if found to contain lead.

Overhead:

• Lead Dust Wipe sampling was performed and results were lower than the SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Deck:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

AFT Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Forward Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Port Bulkhead:

• No sampling was performed.

• Recommend bulk paint chip sampling.

Starboard Bulkhead:

• Lead Dust Wipe sampling was performed and results were lower than SFLC Standard Specification 0000.

• Recommend bulk paint chip sampling.

Other:

• Entry Way Step o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Top of Waste Tank o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

• AFT Center Overhead Pipe o Lead Dust Wipe sampling was performed and results were lower than SFLC Standard

Specification 0000.

o Recommend bulk paint chip sampling.

• Overhead Pipe Center o Bulk sampling was performed and the results were above HUD standards (0.5% by weight).

o Piping in this area should be abated or stabilized.

6.20 Barge Forward Rake

Coat Failure

Multi Coat

Failure

Paint Failure

Paint Abrasion

Chipped Paint

Overhead X X X

Deck X X X

Forward Bulkhead X X X

AFT Bulkhead X X X

Description

Sample Result (By Weight)

Greater than HUD Standard

(0.5 % by weight)

Notes

FR – L01 Forward Rake Deck

Forward Center

Multi-Layer Paint

<0.0074% No See Note A

FR – L02 Forward Rake Starboard Bulkhead

Center

Multi-Layer Paint

<0.0033% No See Note A

FR – L03 Forward Rake Overhead Starboard

Multi-Layer Paint

0.0079% No See Note A

FR – L04 Forward Rake Overhead Starboard

Multi-Layer Paint

0.0084% No See Note A

Note A: Although the sample is less than the Permissible Exposure Limit, the paint still contains lead and…