IPD 5429.doc

ITEM PURCHASE DESCRIPTION

General Services Administration

7510-01-652-5429 UI: CS

TAPE, PRESSURE SENSITIVE ADHESIVE

DESCRIPTION

IN ACCORDANCE WITH SAE-AMS-T-22085, TAPES, PRESSURE-SENSITIVE, ADHESIVE, PRESERVATION AND SEALING

ITEM NAME

TAPE, PRESSURE SENSITIVE ADHESIVE

I.A.W.

3M P/N 481 1 IN X 36 YD

TYPE II - FOR USE WITH OR WITHOUT OVERCOATING

OVERALL WIDTH

1.000 INCHES

OVERALL LENGTH

36.00 YARDS (PER ROLL)

CORE DIAMETER

3.000 INCHES

OVERALL THICKNESS

0.009 INCHES

UNIT TYPE

PRESERVATION SEALING TAPE

OVERALL COLOR

BLACK

OVERALL MATERIAL

COTTON, LINEN, PLASTIC, OR PAPER

SURFACE LUSTER

LUSTERLESS

MATERIAL TRANSPARENCY

OPAQUE

ADHESIVE LOCATION

ONE SIDE

USAGE DESIGN

FOR EXTERIOR PRESERVATION AND SEALING OF MILITARY

VEHICLES, AIRCRAFT, MISSILES AND OTHER RELATED

EQUIPMENT DURING HANDLING, SHIPMENT AND STORAGE

ENVIRONMENTAL PROTECTION

WEATHER RESISTANT

UNIT PACKAGE QUANTITY

36 ROLLS PER CASE

PACKAGING/PACKING: Thirty-six (36) pressure sensitive adhesive tapes shall be packaged in a case in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

PACKAGING/PACKING

SHELF LIFE

ITEM: Tapes, Pressure Sensitive, Adhesive

Type II: Extendable

Age on Delivery: 4 Months

Shelf Life Code: 6 (24 Months Extendable Shelf Life)

Tapes shall be delivered within four (4) months after the manufacture date, and have a shelf life of twenty-four (24) months after the manufacture date. After twenty-four (24) months, the Government reserves the right to extend the shelf life at its discretion.

SHELF LIFE MARKINGS: Unless otherwise specified in the contract or purchase order, each roll and intermediate container shall be marked with the date of manufacture, expiration or inspection date, and lot/batch number as applicable.

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations - In accordance with MIL-STD-129P, dated December 15, 2002, and Change 4, dated September 19, 2007. Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

PALLETIZATION

PALLETIZATION & PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activity. The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade . Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment. Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17.

PCM

GSA prefers and encourages the procurement of Pressure Sensitive Adhesive products that are Executive Order 13148, Sec. 702 compliant. Information on E.O. 13148 may be found at:

www.archives.gov/federal-register/executive-orders/disposition.html.

THE GENERAL SERVICES ADMINISTRATION POLICY IS TO SEEK THE HIGHEST PERCENTAGE OF RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offerer/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market. The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which impair its usefulness. The material shall be free from dirt, contamination, mold release compounds, or other foreign matter.

Printed on: 6/28/2018, 8:57:28 AM Page 2

_1126594845.doc