IPD 5427.doc

ITEM PURCHASE DESCRIPTION

General Services Administration

7510-01-652-5427 UI: CS

TAPE, PRESSURE SENSITIVE ADHESIVE

DESCRIPTION

TAPES, PRESSURE SENSITIVE ADHESIVE, MASKING, NON-STAINING - FOR AIRCRAFT PAINTING APPLICATIONS

ITEM NAME

TAPE, PRESSURE SENSITIVE ADHESIVE

I.A.W.

3M P/N 218 2 IN.

TYPE: III - PLASTIC

OVERALL WIDTH

2.000 INCHES

OVERALL LENGTH

60.00 YARDS (PER ROLL)

OVERALL CORE DIAMETER

3.000 INCHES

OVERALL THICKNESS

0.005 INCHES

OVERALL COLOR

GREEN

OVERALL MATERIAL

PLASTIC

SURFACE LUSTER

MATTE

MATERIAL TRANSPARENCY

OPAQUE

ADHESIVE LOCATION

ONE SIDE

ADHESION TO STEEL

37 OZ/IN WIDTH (40 N/100 MM) IAW ASTM D-3330

TENSILE STRENGTH

13 LBS/IN WIDTH (228 N/100 MM) IAW ASTM D-3759

ELONGATION AT BREAK

720% IAW ASTM D-3759

TEMPERATURE RATING

CYCLE UP TO 250F (121C) FOR UP TO 30 MINS

SPECIAL FEATURE

TAPE SHOULD NOT BE SUBJECTED TO OUTDOOR EXPOSURE

OR PROLONGED PERIODS OF SUNLIGHT AS TAPE MAY

BECOME DIFFICULT TO REMOVE

UNIT PACKAGE QUANTITY

24 ROLLS PER CASE

PACKAGING/PACKING: Twenty-four (24) pressure sensitive adhesive tapes shall be packaged in a case in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

PACKAGING/PACKING

SHELF LIFE

ITEM: Tapes, Pressure Sensitive, Adhesive

Type II: Extendable

Age on Delivery: 2 Months

Shelf Life Code: 4 (12 Months Extendable Shelf Life)

Tapes shall be delivered within two (2) months after the date of manufacture and have a shelf life of twelve (12) months after the date of manufacture. After twelve (12) months, the Government reserves the right to extend the shelf life at its discretion.

SHELF LIFE MARKINGS: Unless otherwise specified in the contract or purchase order, each roll and intermediate container shall be marked with the date of manufacture, expiration or inspection date, and lot/batch number as applicable.

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations - In accordance with MIL-STD-129P, dated December 15, 2002, and Change 4, dated September 19, 2007. Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

In addition, supplier shall provide MSDS in accordance with Fed-Std-313D, dated April 3, 1996, and Change Notice 1, dated March 21, 2000.

MSDS - Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities.

PCM

THE GENERAL SERVICES ADMINISTRATION POLICY IS TO SEEK THE HIGHEST PERCENTAGE OF RECOVERED MATERIAL, INCLUDING POST CONSUMER RECOVERED MATERIAL, WHICH IS COMMERCIALLY AVAILABLE. PROCUREMENT PREFERENCE WILL BE GIVEN TO ITEMS WITH THE HIGHEST POST CONSUMER MATERIAL CONTENT WITHIN REASONABLE COST.

Regulatory Requirements: The offerer/contractor is encouraged to use recovered materials to the maximum extent practicable in accordance with paragraph 23.403 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market. The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which impair its usefulness. The material shall be free from dirt, contamination, mold release compounds, or other foreign matter.

Printed on: 6/28/2018, 8:55:46 AM Page 1

_1126594845.doc