4. Maintenance Specs.pdf

TYPICALS

805 MOBILIZATION / EQUIPMENT MOVING (10/16)

1. DESCRIPTION

This Section consists of one or more mobilizations of personnel, equipment, supplies, and incidentals to the project site, or sites listed in the Schedule of Items.

2. REQUIREMENT

a. Make equipment available for inspection before it is used on National Forest System lands.

b. Moving is complete, when the contractor has moved from the present work site to the ordered work site and returned to the previous location.

c. Equipment will be clean and weed free before it arrives on National Forest System lands.

3. LOCATION OF WORK

As specified on roads listed on the Road Listing, Shown on the Plans, or as ordered by the Contracting Officer.

4. MEASUREMENT

Measurement under this Section will be made by the total number of units for each item listed in the Schedule of Items completed and accepted.

Mile: work activity will be measured along the shortest feasible route to the nearest one (1) mile, from the starting location of the move, to the ordered work site.

5. PAYMENT

a. The accepted quantities will be paid at the contract price per unit of measurement for the Section 805 pay items listed in the schedule of items. Mobilization is complete when all equipment, personnel, and materials are moved to the project site and work has been started. Payment will be full compensation for the work prescribed in this Section.

Mobilization is incidental unless ordered for a specific project at a specific time.

b. Payment will be made under:

Pay Item Description Pay Unit

805 (1) Mobilization Mile

811 BLADING (10/16)

This work consists of

a. Surface blading native or aggregate roadbed to a condition to facilitate traffic and provide proper drainage.

b. Smooth blading to remove loose surfacing materials from the wheel paths and store the removed materials in a recoverable windrow.

Blading includes shaping the crown or slope of traveled way, berms, and drainage dips in accordance with this specification. Compaction is required when ordered by the Contracting Officer.

2. MAINTENANCE REQUIREMENTS

a. Timing

Surface blading shall be performed during the contract period as ordered by the Government.

b. General

1) The existing traveled way and shoulders, including turnouts unless otherwise ordered, shall be bladed and shaped to produce a surface which is uniform, consistent to grade, and crowned or cross-sloped as indicated by the character of the existing surface unless otherwise shown in the Road Listing, to at least one half inch (1/2") per foot of width, but not more than three quarter inch (3/4") per foot of width. Surfacing materials shall be thoroughly loosened to no less than 2 inch depth or the depth of potholes or corrugations. Scarification to facilitate cutting to the full depth of potholes or corrugations may be elected by the Contractor but will be considered incidental to blading. Scarification shall not go deep enough to cause contamination of the surfacing.

2) When Section 891 is included in the Road Listing, the Contractor shall apply water during blading when sufficient moisture is not present to prevent segregation. Water supply, hauling, and application shall be in accordance with Section 891 and shall be incidental to blading unless Pay Items for Section 891 are included in the Schedule of Items.

3) Existing native, rock or aggregate surfaced drainage dips shall be shaped incidental to blading to divert surface runoff to existing outlet devices, ditches and discharge locations.

4) The Contractor shall establish a blading pattern which provides a uniform driving surface, retains the surfacing on the roadbed and provides a thorough mixing of the materials within the completed surface width. Upon final blading, no disturbed rock shall protrude more than two (2) inches above the adjacent surface unless otherwise provided in the contract. Material not meeting this dimension shall be removed and placed outside the roadbed so as not to obstruct drainage ways or structures. This material may be scattered off the roadbed if there is free drainage.

5) Watering will not be required for smooth blading. Smooth blading shall be accomplished without distorting the existing cross-slope or crown of the traveled way. Loose surfacing materials shall be moved and stored on the high side of super-elevated curves and sections with uniform inslope or outslope. In crowned sections, the material shall be stored on either or both sides as elected. Stored materials shall be windrowed and shall be placed to provide not less than eleven (11) feet of smoothed traveled way on one- lane segments or twenty (20) feet of smoothed traveled way on two-lane or sections with turnouts. Windrows which may collect water on the road shall have holes cut through for drainage at least every 500 feet.

c. Routine Blading

1) Upon completion of blading, the surfaces shall conform to the dimensions shown in the Special Project Specifications 811-3.

2) Roadbed width in excess of the dimensions shown shall be shaped only as needed to provide drainage away from the traveled way. Established grasses and other vegetation shall not be removed from the excess width except as incidental to providing drainage or unless otherwise provided in the contract.

d. Compaction

Roads requiring compaction will be included in the Road Listing. Unless otherwise specified, all traveled ways requiring compaction shall be compacted by breaking track while operating equipment on the traveled way.

e. Intrusions

Where the minimum width shown in the Special Project Specifications is not available, the Contractor will construct berms where ordered and marked on the ground. Material to provide berms will come from sources designated in the Special Project Specifications.

f. Undercutting

Roadway back slope shall not be undercut.

g. Intersections

1) At intersections, the roadbeds of side roads which are not closed or restricted from vehicular use shall be bladed to assure smooth transitions.

2) Field evidence of closure or restrictions shall be considered to be signing, cross ditching in the road surface (traveled way), earth berms or other devices placed to discourage or eliminate use by passenger cars, also roads listed for work under Sections 835 or 838 shall be considered restricted.

3) Side roads listed for work under this Section shall be considered as not restricted.

h. Cleaning of Structures

Materials resulting from work under this Section shall not be allowed to remain on or in structures, such as bridges, culverts, cattleguards, or drainage dips.

i. Berms

Existing berms shall be maintained to the condition of adjacent segments when ordered by the Government.

3. MEASUREMENT

a. Measurement under this Section will be made by the total number of units for each item listed in the Schedule of Items completed and accepted.

b. Measurement for blading will be single-lane mile measured along the centerline of the roadway (see quantity measurement terms). Two-lane roads will be measured as two

(2) single-lane miles. Measurement will be measured to the nearest one-tenth (0.1) mile.

c. Each intersection bladed under 2.g. will be equivalent to one-tenth (0.1) single-lane mile; however, when the intersecting side road is scheduled for subsequent blading under this Section, no measurement will be made.

d. Berm maintained or established will be measured by linear foot.

e. No measurement will be made under this Section for compaction method specified in 2.d. For roads needing compaction with special compaction equipment (ie. pneumatic or steel roller), use pay items in Section 807 for additional compaction efforts.

4. PAYMENT

a. The quantities measured and accepted will be paid for at the contract unit price shown in the Schedule of Items.

b. Payment will be made under:

Pay Item Description Pay Unit

811 (1) Blading Surfaced Roads Single-Lane Mile

811 (2) Blading Native and Pit Run Roads Single-Lane Mile

811 (3) Smooth Blading Single-Lane Mile

811 (4) Berm Maintained Linear Foot

811 (5) Establishing Berms Linear Foot

813 SPOT SURFACING (10/16)

This work consists of placing surface aggregate as staked on the ground, or designated by the Government. It includes preparing the area, furnishing, hauling, and placing all necessary materials and other work necessary to blend with the adjacent road cross section.

2. MATERIALS

a. Materials will be Government furnished when stated in the task order.

b. Materials furnished by the Contractor shall conform to the gradation requirements shown in the task order and the quality requirements of Section 893.

3. MAINTENANCE REQUIREMENTS

The area to be spot surfaced shall be thoroughly loosened to a minimum depth of one inch (1") prior to placement of aggregate.

4. MIXING AND PLACING

a. When scheduled coincident with work under Section 811, spot surfacing and existing aggregate, when ordered, shall be mixed with water until a uniform mixture is obtained prior to final shaping and compaction.

b. The material shall otherwise be spread on the prepared area in layers no more than four

(4) inches in depth. When more than one (1) layer is required, each layer shall be shaped and compacted before the succeeding layer is placed. Upon completion, the spot surfacing shall reasonably conform to the adjacent cross section and provide smooth transitions in the road profile.

c. Compaction shall be accomplished by breaking track while operating equipment on the traveled way

5. MEASUREMENT

a. The quantity will be the weight of the actual aggregate placed in tons, cubic yards of aggregate measured in place, or square yards of aggregate measured in place, whichever is shown in the Schedule of Items.

b. Hauling is considered incidental.

6. PAYMENT

a. The accepted quantities will be paid for at the contract unit prices shown in the Schedule of Items

b. For payment by weight, certified weight ticket shall be submitted to the Contracting Officer.

c. Payment will be made under:

Pay Item Description Pay Unit

813 (1) Spot Surfacing, Grading__, Commercial Source

Ton

813 (2) Spot Surfacing, Grading__, Commercial Source

Cubic Yard

813 (3) Spot Surfacing, Grading__, Commercial Source

Square Yard

813 (4) Spot Surfacing, Grading__, Government Source

Ton

813 (5) Spot Surfacing, Grading__, Government Source

Cubic Yard

813 (6) Spot Surfacing, Grading__, Government Source

Square Yard

814 ASPHALT PAVEMENT PATCHING (10/16)

This work consists of patching potholes and skin patching of asphalt surfaces. The work includes preparing the area to be patched, furnishing and placing all necessary materials and work. All areas to be patched will be marked by the Government.

2. MATERIALS

Materials used for asphalt patching shall conform to the requirements in Sections 892 and

893. Bituminous mixture material shall conform to requirements of Special Project Specifications.

3. MAINTENANCE REQUIREMENTS

a. Potholes

1) Existing materials shall be removed to a minimum of two (2) inches or as necessary to reach firm support, but limited to maximum twelve (12) inch depth. If firm support for a patch is not available, the hole shall be barricaded and the Government shall be notified. Prior to Contractor placing any materials, Government will determine corrections to be made.

2) The edges of the prepared hole shall be extended to form a vertical face in un-fractured asphalt surfacing. The prepared hole shall generally be round or rectangular in shape and cleaned of all loose material. The bottom and sides shall be sprayed with an emulsified asphalt.

3) Prepared potholes shall be patched or barricaded immediately.

4) The bituminous mixture shall be placed in layers not exceeding four (4) inches. Each layer shall be compacted thoroughly with hand tampers, mechanical tampers, or rollers.

5) Finished surface shall, as a minimum, be compacted with a tamper or an 8- to 10-ton steel roller or comparable vibratory roller. Upon completion, the compacted pothole patch shall be flush with or not more than one quarter (1/4) inch above the level of the adjacent pavement.

b. Disposal

All materials removed from pothole and skin patching operations shall be removed to a disposal site designated by the COR or shown on the drawings.

4. MEASUREMENT

a. Bituminous Mixture

1) Hot and cold bituminous mixture acceptable placed will be measured by the ton.

Bituminous materials incorporated into the mixture will be incidental to the item.

2) Ton Measure - The quantity of mixture will be the number of tons in the accepted work. Any material rejected in the field as not meeting specifications shall be deducted based on estimated quantities. Rejected quantities shall be reconciled between the Government and the Contractor each day. If not reconciled each day, the Government's figures will apply.

b. The following work is incidental:

1) Cleaning of surfaces.

2) Haul and compaction of bituminous mixture.

3) Material removal and disposal.

4) Emulsified asphalt used on existing surfaces will be measured by the gallon prior to dilution. Dilution materials shall be considered incidental.

5. PAYMENT

a. The accepted quantities will be paid for at the contract unit price shown in the Schedule of Items.

b. Payment will be made under:

Pay Item Description Pay Unit

814 (1) Pothole Patching Ton

814 (2) Emulsified Asphalt Gallon

839 RESTORE DRAINAGE (10/16)

This work consists of log, limb and debris removal; blading and shaping of the roadbed to restore drainage function. This work includes shoulders, ditches, drainage dips, leadoff ditches, turnouts, and intersections; cleaning drainage facilities; removing washes and sloughs that inhibit drainage.

2. MAINTENANCE REQUIREMENTS

a. General

The existing traveled way and shoulders, including turnouts unless otherwise ordered, shall be bladed and shaped to produce a surface which is uniform, consistent to grade, and crowned or cross-sloped as indicated by the character of the existing surface unless otherwise Marked on the Ground, to at least one half inch (1/2") per foot of width, but not more than three quarter inch (3/4") per foot of width. Surfacing materials shall be thoroughly loosened to a depth of no less than 2 inches or the depth of potholes or corrugations.

Corrugations are washboarding and similar defects.

Scarification to facilitate cutting to the full depth of potholes or corrugations may be elected by the Contractor but will be considered incidental to blading. Scarification shall not go deep enough to cause contamination of the surfacing.

When Section 891 is included in the Road Listing, the Contractor shall apply water during blading when sufficient moisture is not present to prevent segregation. Water supply, hauling, and application shall be in accordance with Section 891 and shall be incidental to blading unless Pay Items for Section 891 are included in the Schedule of Items.

Existing native, rock or aggregate surfaced drainage dips shall be cleaned and shaped incidental to blading to divert surface runoff to existing outlet devices, ditches and discharge locations.

The Contractor shall establish a blading pattern which provides a uniform driving surface, retains the surfacing on the roadbed and provides a thorough mixing of the materials within the completed surface width.

b. Drainage Facilities

Cleaning existing drainage facilities includes roadside drainage ditches, drainage dips, inlet and outlet ditches, overside drains and flumes, inverts and interiors of culverts, culvert catch basins, drop inlets, trash racks, and sediment basins. Slash and debris shall be disposed of as in 839e. Sediment basin clean out shall be disposed for the unit price as shown in the Schedule of Items for Section 832.

Drainage structures not included under this specification are bridges, cattle guards, and culverts over 72 inches in diameter.

c. Ditches, Lead Off and Roadside

Wood, rock, trees, brush and other debris shall be removed from ditches to provide unobstructed flow of water. Slash and debris (woody or organic) shall be scattered in such a manner as not to impede the flow of water. The backslope of ditches shall not be undercut by cleaning operations. Existing ditch blocks shall be restored, reshaped, and compacted as needed for effective drainage through culverts. Catch basins shall be cleaned of material above the invert of the culvert.

d. Dips (Also called intercepting dips or rolling dips)

Existing drainage dips shall be cleaned and the outslope gradient sufficiently restored to remove surface water from roadbed, conducting the water through drainage facilities.

e. Culverts

Inlet and outlet ends, as well as four feet inside each end, of existing culvert, shall be cleaned to provide unobstructed flow of water. Natural drain culvert channels shall be cleared of all down trees, limbs, stumps, brush, rocks and other debris, that restricts the flow of water, 6 feet in width for 15 linear feet at each end. Slash and debris (woody or organic) shall be scattered in such a manner as not to impede the flow of water. The channel shall be shaped to natural streambed with constant grade at inlet and outlet ends.

f. Overside Drains and Flumes

Overside drains shall be cleaned of debris to provide an unobstructed flow of water. Debris (woody or organic) shall be scattered in such a manner as not to impede the flow of water.

g. Designed Earth Berms

Berm breaches of less than 5 cubic yards shall be filled, shaped, and compacted by wheel rolling. Fill material shall be located within 500 feet of breach or by ripping to the depth and width necessary to obliterate such defects; providing a smooth transition to adjacent satisfactory roadbed. Filling with loose material will not be acceptable.

h. Settlements

Settlements 12 inches or less in depth shall be scarified and then repaired by cutting from the roadbed on each end of the settled area, filling and wheel rolling the material into the settled area providing a smooth transition to adjacent satisfactory roadbed.

i. Washouts

Washouts in roadway of less than five cubic yards shall be filled and compacted by wheel rolling. Fill material shall be located within 500 feet of washout or as directed by the Contracting Officer.

3. METHOD OF MEASUREMENT

Measurement for maintenance will be slope distance along the centerline of the roadway. Measurement will be to the nearest one-tenth mile. No separate measurement will be made for any of the elements of work described in the foregoing

4. PAYMENT

a. Payment will be made for all units inspected and accepted at the unit price shown on the schedule of items.

b. Payments will be made under:

Pay Item Description Pay Unit

839 (1) Restore Drainage Function, Without Water Mile

839(2) Restore Drainage Function, With Water Mile

840 CORRUGATED METAL SPILLWAYS AND FLUME (10/16)

This work consists of cleaning, reconditioning, and re-installing, or the replacement of existing corrugated metal spillway inlet assemblies, flume, and other appurtenances associated with the installation requirements.

2. MATERIALS

a. Materials shall be furnished by the contractor, unless otherwise indicated. Spillway inlet assemblies, flume, and connectors shall be of the type and thickness specified by the Task Order or shown in supplemental drawings, and shall be constructed of galvanized corrugated sheet metal meeting the requirements indicated on the drawings.

b. Anchors shall be as shown in the Task Order.

3. MAINTENANCE REQUIREMENTS

a. Re-installation of existing overside drains:

1) Re-install inlet and starter section to the grade and flow line established by the drainage dip.

2) Adjacent earth berms shall be filled shaped, and compacted to provide a continuous drainage channel to the inlet structure.

3) Structures not approved for reuse shall be removed from Government land at the

4) Prior to re-installing flume, ensure that voids have been filled and the embankment compacted to provide a smooth, continuous grade from the inlet to the outlet of drainage structure.

b. Replacement of existing overside drains:

1) Remove existing structure and backfill and compact any wash-outs beneath the inlet and starter.

2) Re-establish the embankment for flume replacement by backfilling wash-outs and voids, and compacting to provide a smooth, continuous grade from the inlet to the outlet of the drainage structure.

3) Install new drainage structure as specified by the Task Order.

4) Re-establish earth berm. Shape and compact to provide a continuous drainage channel to the inlet of the drainage structure.

4. MEASUREMENT

a. Measurement of inlet and starter assemblies will be for each unit specified and installed as a whole. Costs included are for materials, labor for fabrication and installation, and delivery.

b. Measurement will be made for each lineal foot of flume specified and installed. Measurement for anchors shall be considered incidental to flume installation.

c. Cost for disposal of removed inlets, starters, flumes, and appurtenances shall be considered incidental to the work in this specification.

5. PAYMENT

a. Accepted quantities will be paid for at the contract unit prices shown in the Schedule of Items.

b. Payment will be made under:

Pay Item Description Pay Unit

840 (1) Clean Inlet and Starter Each

840 (2) Reinstall Inlet and Starter Each

840 (3) Replace Inlet and Starter ___ (12, 18, 24, or 36) Inches

Each

840 (4) Clean Flume Each

840 (5) Reinstall Flume Linear Foot

840 (6) Replace Flume, ____ (12, 18, 24, or 36) Inches Linear Foot

840 (7) Replace Flume, Each

2'-0.25"

R1.5"

R1.5"

2'-0.25"

1'-11.5"

1"

7.2"

1"

7.2" 7.2"

1"

0.4" TYPICAL

1"

1"

6'-0"

2'-.25"

2'-.25"

U n i t e d

S t a t e s

D e p a r t m e n t o f

A g r i c u l t u r e

840-2a

F o r e s t

S e r v i c e

R

P

A C

I F

I C

S

O U

T H

W E

T

A

N G

E

LE

S

N

A T

I O

N A

L

F

O R

E S

T

LO

S

A N

G E

LE

U

N T

Y

C A

L I F

O R

N I A

CONSTRUCTION

DETAILS

OVERSIDE DRAIN

FABRICATION

24" HEADWALL

SHEET 2 OF 3

OVERSIDE DRAIN

ALTERNATE

SCALE: NTS

*Material-14 Guage Galvanized Sheet Metal j a•========::::;

t f-0 0

1'-11.5"

1.0"

7.2"

2.0"

2.0"

1.0"

R0.5"

R0.5"

0.4" TYPICAL

7.2" 7.2"

1.0"

2'-6"

2'-9.8"

R7"

1.5"

1.5"

U n i t e d

S t a t e s

D e p a r t m e n t o f

A g r i c u l t u r e

840-2a

F o r e s t

S e r v i c e

R

P

A C

I F

I

U

T H

W E

T

A

N G

E

LE

S

N

A T

I O

N A

L

F

O R

E S

T

LO

S

A N

G E

LE

U

N T

Y

C A

L I F

O R

N I A

CONSTRUCTION

DETAILS

OVERSIDE DRAIN

FABRICATION

24" STARTER

SHEET 2 OF 3

OVERSIDE DRAIN

ALTERNATE

SCALE: NTS

*Material-16 Guage Galvanized Sheet Metal

2 2

' E IDND OF < FlRS SECTION OF

ME SH & D ON LL

srcliON B-BI

INS ALL r, PRAP CLASS 2 O~~

Ov DRAINS (AP1>ROX 1 C. 'I".)

RIPR Ae;,JNSJAU,A,TlQl:i

A ~HOR· STAK S

T'l1" 1 E 2.

CALV, :},Ill'• 1 1/2' ~6" CALV, 319•~1 1 /4">- 1 /2; 0

W/ UT MID n A 'f / •~1 1.12• ij v. MACHll'i 0 T

W/i UT ANO FLAT •~•AS R t,'IHE: . LLOWANCE I ctUOES 1 GAL\I'.

/ N M-ID LAl W -l' I 't.'A'( ~ - 1$ <!< F'I. UM nP.£.

A-A

6,0'

B

·~3r A lV,iJ"'L GR D

.5'

TO.? OF BERM

FACE Oi' filRM

011N ~ll

NOTE: !..EARING FOR SIA & FLU E SHALL

B 2 M IMUM, TO A SI

Cir STR CTURE. CILA G ABQI/E

STRUCTURE S ALL BE 4 F . INIMUM.

ARTh!ENT OF AGR:ICU TURE

FOOEST SER';ICE ~EC!CN I\

FORS CLEVE

co ETAILS

OF 'J